Irrigation And Flood Control Department Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Irrigation And Flood Control Department Tender
Civil And Construction
Building Construction
Eprocure
Opening Date13 Dec 2024
Closing Date20 Dec 2024
Tender Amount₹ 2,30,87,184.31
Costs
EMD
₹ 4,61,766Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_IFC_266474_1Bid Award Id
ViewTender No
EE/CD-VI/ACS-119/2024-25Tender Authority
Irrigation And Flood Control Department ViewPurchaser Address
-
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
Supplying an filling in plinth with Jamuna sand under floors including watering, ramming, consolidating and dressing complete
31
980
30381.55
... More
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size) .
51
5141
262213.95
... More
Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete, For pipes 100 to 250 mm diameter.
1
417
417.7
... More
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately) - All works upto plinth level
149
6884
1025738.35
... More
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately) - All works above plinth level upto floor IInd level.
196
7227
1416580.2
... More
Centering and shuttering including strutting, propping etc. and removal of form for:
-
-
-
... More
Foundations, footings, bases of columns etc. for mass concrete.
199
207
41212.9
... More
Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
40
404
16172
... More
Suspended floors, roofs, landing, balconies and access platform.
601
450
271020.95
... More
Lintels, beams, plinth beams, girders, brussumers and cantilevers.
452
366
165522.4
... More
Columns, pillars, pier, abutments, posts and struts.
238
499
118904.8
... More
Stairs (excluding landings) except spiral staircases
37
447
16568.6
... More
Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level or above plinth level. Thermo-Mechanically Treated bars.
47936
60
2897731.2
... More
Granite (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the granite shade (To be secured to the backing by means of cramps, which shall be paid for separately).
1073
4897
5254481
... More
Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. 10 x 120 mm.
8584
98
841661.2
... More
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement Mortar 1:6 (1 cement : 6 coarse sand).
25
5074
126857.5
... More
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floorIInd level in all shapes and sizes in : Cement Mortar 1:6 (1 cement : 6 coarse sand).
163
5446
887722.45
... More
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement Mortar 1:4 (1 cement : 4 coarse sand).
16
730
11690.4
... More
Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry (with F.P.S. bricks)
16
60
971.2
... More
Granite (polished and machine cut) of thickness 18 mm for skirting, riser of steps etc.laid on 12 mm (average) thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the granite shade, including rubbing and polishing complete.
19
4839
91950.5
... More
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design - 100 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
2
1711
3422.4
... More
Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.
1923
247
475365.6
... More
Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required.
421
556
234286.5
... More
Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases.
8584
31
272971.2
... More
Providing and fixing 18 mm thick gang saw cut mirror polished, premoulded and prepolished machine cut for kitchen platform, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touh ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shade, Area of slab over 0.50 sqm.
31
3324
103065.7
... More
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge- Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent
529
3137
1659552.35
... More
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
12
414
4977
... More
Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete - 100x75x4 mm
158
93
14773
... More
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200 x 10 mm
50
81
4065
... More
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100 x 10 mm
55
52
2890.25
... More
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm.
34
54
1854.7
... More
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper.
12
29
352.8
... More
Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp of internal dia. 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheetwith its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/M.S. sheet box by means of 3.3 mm dia. round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia. M.S. bar bent to shape as per standard drawing.
22
138
3056.9
... More
Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
1024
504
516608
... More
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
260
1236
321555
... More
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
11
1322
14544.75
... More
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.
207
795
164637.45
... More
Providing and laying ceramic glazed floor tiles 300 x 300 mm (thickness to be specified by th manufacturer) of 1st quality conforming to IS:15622 of approved make in colours, shades except white, Ivory, Grey, Fume red brown laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc. complete.
41
798
32746.7
... More
Extra for pre finished nosing to treads of steps of marble stone.
125
327
40881.25
... More
Making khurras 45 X 45 cm with average minimum thickness of 5 cm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1m X 1m X 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete
5
200
1001.75
... More
Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes, 110 mm diameter.
29
252
7319.6
... More
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised- Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion Bend 87.5 degrees, 110 mm bend.
3
120
362.4
... More
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised- Rigid PVC rain water pipes conforming to IS:13592 Type A including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion Shoe (plain), 110 mm Shoe.
3
104
313.95
... More
Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length including cutting brickwork and fixing In cement mortar 1:4 (1 cement : 4 coarse sand) and making good the walls etc. complete, 110 mm.
49
193
9491.3
... More
Cutting holes upto 30 x 30 cm in walls including making good the same With common burnt clay F.P.S. (non modular) bricks.
5
230
1150.5
... More
12 mm cement plaster of mix: 1:4 (1cement: 4 fine sand).
114
184
21055.8
... More
15 mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1cement: 6 fine sand).
20
197
3956
... More
Providing and filling light weight foam concrete in shunken portions of toilet including compacting etc. complete as required
10
4324
43240
... More
Constructing brick masonary manhole in cement mortar 1:4 (1 cement : 4 coarse sand) R.C.C top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floting coat of neat cement complete as per standard design: Inside size 90 x 80 cm and 45 cm deep including C.I. cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.
4
9220
36881.4
... More
6 mm cement plaster of mix: 1:3 (1 cement : 3 fine sand).
912
153
140037.6
... More
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
1026
126
130045.5
... More
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: New work (two or more coats) over and including water tinnable priming coat with cement primer.
1026
100
102651.3
... More
Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
20
103
2067
... More
Supply of earth at site including excavation, royalty, loading, unloading and banking the same in layers not exceeding 20 cm in depth, breaking clods and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions including carriage of earth by mechanical transport lead upto 10.00 km and lift upto 1.50m. All kinds of soil.
92
567
52187
... More
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285 fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for seperately.) - For fixed portion - Powder coated aluminium (minimum thickness of powder coating 50 micron)
244
410
100186.4
... More
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285 fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/panelling, C.P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for seperately.) - For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of PVC/neoprene gasket required (Fittings shall be paid for seperately). - Powder coated aluminium (minimum thickness of powder coating 50 micron)
324
475
153932.4
... More
Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.
21
925
19434.45
... More
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) - With float glass panes of 5.50 mm thickness
27
1072
28946.7
... More
Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.
10
383
3834
... More
Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete - Powder coated minimum thickness 50 micron aluminium
36
59
2133
... More
Providing and laying water proofing treatment in sunken portion of W.C., bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying: a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours.b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate included preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonary with polymer mixed slurry.
62
318
19750.1
... More
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm. of cement admxed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge over the R.C.C. slab including adjoining walls upto 300 mm height including cleanng the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bas 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS:2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. c) After two days of proper curing applying a second coat of cementslurry using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compoundconforming to IS:2645 and approved by Engineer-in-charge including laying glass fiber cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cemen slurry and making pattern of 300 x 300 mm square 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of 2 weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge: With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
294
1104
324840.6
... More
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge
5
272
1360.5
... More
Providing and fixing 100 mm sand cast iron grating for gully trap
2
31
62.5
... More
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm.
9
1412
12716.55
... More
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.
5
10343
51716.75
... More
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern
7
3731
26119.8
... More
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
9
2454
22091.4
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall, 32 mm nominal outer dia Pipes.
27
308
8334.36
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm dia. Nominal bore.
350
304
106470
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work - 32 mm nominal outer dia Pipes
5
267
1337.75
... More
Providing and fixing brass bib cock of approved quality : 20 mm nominal bore.
6
299
1796.7
... More
Providing and fixing brass stop cock of approved quality. 20 mm nominal bore
5
299
1497.25
... More
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 32 mm nominal bore.
1
534
534.75
... More
Providing and fixing ball valve (brass) of approved quality, High or low pressure with plastic floats complete, 20 mm nominal bore.
1
349
349.25
... More
Providing and fixing unplasticised PVC connection pipe with brass unions, 30 cm length, 20 mm nominal bore.
1
69
69.65
... More
Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI:12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
2000
7
15500
... More
Providing and fixing C.P. brass angle valve for basin mixer and gyser points approved quality conforming to IS:8931 a) 15 mm nominal bore, 15 mm nominal bore.
21
508
10668
... More
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
16
849
13586.4
... More
Providing and fixing C.P. liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality colour and make, weighing not less than 105 gms
5
1692
8463.5
... More
Providing and fixing Unplasticised - Rigid PVC pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 for soil, waste and vent : 110mm dia.
85
252
21454
... More
Providing and fixing UPVC plain bend of required degree, 110 mm dia.
40
120
4832
... More
Providing and fixing UPVC single equal plain junction of required degree without access door complete, 110 x 110 x 110 mm.
11
242
2670.25
... More
Providing and fixing UPVC single equal plain tee complete, 110 x 110 x 110 mm.
14
179
2506
... More
Providing and fixing UPVC cowel, 110 mm.
7
65
457.45
... More
Providing and fixing UPVC coupler, 110 mm.
22
109
2411.2
... More
Providing, laying and jointing UPVC pipe in trenches including testing of joints etc. complete 160 mm diameter.
19
715
13589.75
... More
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround PVC pipes including bed concrete as per standard design: 150 mm diameter PVC pipe.
19
813
15458.4
... More
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil, 300 mm dia.
80
395
31668
... More
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge - 100 mm nominal size dia
40
478
19138
... More
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge - 200 mm nominal size dia
40
876
35076
... More
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
1
984
984.5
... More
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge.
1
1108
1108.55
... More
Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.
1
1108
1108.55
... More
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
1757
72
126855.4
... More
Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required - 0.63 mm thick with zinc coating not less than 275 gm/ m²
62
748
46382.2
... More
Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required. Group C.
191
808
154404.4
... More
Wiring for light / power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
1926
179
345524.4
... More
Wiring for light / power plug with 4 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit alongwith 2 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
986
300
295898.6
... More
Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required.
-
-
-
... More
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
784
146
114699.2
... More
4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire
942
229
216283.2
... More
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
697
242
168952.8
... More
4 X 6 sq. mm + 2 X 6 sq. mm earth wire
686
421
289354.8
... More
4 X 10 sq. mm + 2 X 6 sq. mm earth wire
658
572
376639.2
... More
Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
26
307
7996.3
... More
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.
65
334
21726.25
... More
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 6/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
28
433
12139.4
... More
Erection of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS lamps per fitting, complete with all accessories including connection etc. as required.
7
61
433.65
... More
Installation, testing and commissioning of pre-wired, fluorescent fitting / CFL / LED fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.
145
106
15486
... More
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.
26
112
2915.9
... More
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep.
5
239
1196
... More
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) - 6 way (4 + 18), Double door
2
2839
5679.1
... More
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) - 8 way (8 + 24), Double door
2
3386
6772.6
... More
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole (OUTGOING MCB'S FOR DB'S).
68
184
12563
... More
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
1
4620
4620.8
... More
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
45
374
16868.25
... More
Supplying and fixing of suitable size GI box with modular plate and cover in front on surface / recess including providing & fixing 25 A modular socket outlet and 25 A modular motor starter including connections, painting etc. as required. (FOR AC SOCKETS).
18
851
15327
... More
Supplying of 15 W surface mounted LED round low depth powder coated luminaire with drop down PC diffuser to deliver low glare illumination complete with LED lamp, connections etc. as required.
89
1172
104308
... More
Supplying of maintenance free, energy saving LED Batten light fixture of 20W suitable for surface mounting on wall or ceiling. The fitting shall be complete with all accessorie etc. as required.
24
360
8640
... More
Supplying of 36 W surface mounted LED light luminaire of size 600mm x 600mm complete with all accessories in the existing points including connection etc. as required.
32
1701
54432
... More
Supplying of 10 W LED bulk head luminaire with all accessories in the existing points including connection etc. as required.
7
2264
15848
... More
Supplying of 1200 mm sweep Power Saver A.C. electric Ceiling fans, capacitor type with double ball bearing complete with 300 mm down rod, canopies, shackles, blades, but without regulator suitable for operation on 230 / 240 Volts, 50 Hz, single phase, A.C. supply etc. as reqd.
26
1758
45708
... More
Supplying of 200 mm dia exhaust fan complete with supplying all accessories such as motor, blades, frame, louvers or ventilator etc. as reqd.
5
1405
7025
... More
Supply, installation, testing and commissioning of following tonnage 3-Star Split type Air Conditioner complete with copper piping upto 5 Mtr., voltage stabilizer, water outlet pipe etc. complete with connections, testing as required : 2 TR
18
74322
1337796
... More
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) - 12 way (8 + 36), Double door (DB'S FOR GF)
1
10250
10250.5
... More
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required - Triple pole and neutral - 63 A (INCOMER MCB'S FOR DB'S).
2
1536
3073
... More
Supplying, installing, testing & commissioning of surface / wall mounted type compartmentalised cubicle board made from 2mm thick CRCA sheet dust & vermin proof duly phosphatized & painted inclusive of 125 Amp 4 strip Al. Busbar complete with interconnection pdg. Lugs, inter-earthing, painting etc. i/c pdg. & fixing below noted accessories.
INCOMING :
200 Amp 415 V FP MCCB having breaking capacity - 50 KA, with Ics=Icu=50 KA, with Rotary Handle operating Mechanism - 1 No. (0-100 A) Ammeter with selector switch & 100/5 C.T.'s (Digital type) - 1 Set, (0-500 V) Voltmeter with selector switch (Digital type) - 1 Set, Indication lamp R/Y/B with backup fuses - 1 Set of Three OUTGOING :
63 Amp 415 V TP MCCB having breaking capacity - 25 KA, with Ics=Icu=25 KA, with Rotary Handle operating Mechanism - 4 Nos., 32 Amp TPN MCB - 10 KA - 6 Nos.
1
139636
139636
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements