India Trade Promotion Organisation Tender

Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge 18 mm thick Italian Marble stone slab Perlato, Bottochino, Rosso verona,Fire Red or Dark Emperadore etc.

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC rofile), uPVC extruded glazing beads of appropriate dimension, EPDM asket, zinc alloy (white powder coated) 3D hinges and one handle on ach side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary tainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineerin- Charge. (The payment of RCC band and reinforcement shall be made for seperately).

15 mm cement plaster on the rough side of single or half brick wall of mix ::1:4 (1 cement : 4 fine sand)

Providing & fixing Acoustical Ceiling having high NRC Greater than equal to 1, Fire Rating A1 (EN 13501-1), RH 100% (No visible deflection in high humidity), Light Reflection 86%, Sag Resistant 15mm thick Ceiling Tiles of size 600x600 E Edge with Anti- Bacterial Properties & M1 Class Emission Certification made up with Natural Stone (Bassalt Rock) a complete Green Product & perfect suitable for any kind of False Ceiling application in builiding & costruction.The Visible side is a smooth white painted fleece, the Rear side: back fleece with complete facctory finish Painted edges. All the products should meet global CE requirment as per EN 13496 : 2014.The system consists of 15mm Acoustic Tiles 600x600 (E Edge) laid in to SILENZO+ SLIMLINE CENTRE BLACK /Silhoutee Suspension System 15mm X 32 X0.30mm system manufactured as per specs of Rockfon, with warranty of 30 Years. INSTALLATION - Suspension System shall be SILENZO+ SLIMLINE CENTRE BLACK/Silhoutte ’ Grid system consisting of Main Runner 3000mm, Cross Tee 1200mm, Cross Tee 600mm & Wall Angle 3050mm.Main runner has 0.3mm PPGI,120 GSM and 25 microns of paint, Cross runner has 0.3mm PPGI, 120 GSM and 25 microns of paint, Wall Angle has 0.4mm TCT PPGI of 120 GSM and 25 microns of paint.• SILENZO+ Suspension System/ Silhoutte - Dimensions: Main Runner: 3000mm x 32mm x 15mm ,Cross Runner:1200mm /600mm X 32mm x 15mm, Wall Angle: 3050mm x 20mm x 14mm. Main runners are suspended at 1200mm c/c by means of GI wire of 2 mm diameter or 4mm rod and not more than 150mm from spliced joints. Cross runners are inserted in to the main runners and locked in position by a slight downward pressure. The GI wire or rod is fixed by means of a dash fastener or by directly fixing it to soffit or sub structure. The last hanger at the end of each runner should not be more than 450mm from the adjacent wall. For perimeter treatments and wall ends, wall angle are used to secure false ceiling Tiles/profiles/boards etc. Axioms can be used for floating ceiling installations.All level and alignment of the Grid shall be accurate. Material shall be installed in strict compliance with local codes and manufacturers recommendations and as directed by site in charge. of Rock fon/Ecofon as per approved sample.

Providing and fixing of the acoustical ceiling baffles in the shape and design as per the drawings suitably suspended from the ceiling made out with square or beveled edge boards manufactured from 100% Polyethylene Terephthalate (PET) having density of 100 ( the panel shall have 60% recycled content) , Kgs/m3, Manufactured panels should be fire resistant as per B1 Class A .

Providing and fixing of the scaffolding for erection of the treatments and AV / Lighting equipment as required as per the site conditions.

Providing and fixing of he modular acosutical panels to form the stage walls consisting of the metal tubular framework complete with 12mm Fire retardant ply fixed on both sides filled with 50mm 1000 GSM polyester wadding . The Fianl finished surface of the partiotion to be acosutical baord on one side and veneer/ lamiante on other side. The panels to be lockable at top rail so as to form acosutical partition dividing area between the PM lounge and auditorium

Providing and fixing of the stage out of MS tube framework and complete with top layer of the 2 nos 18mm thick Fire-retardant ply over MS tube franework completely secured with Nut bolt arrangment counter sunk in the framework. The modular framework to be of the modules of size 1200x2400 and shall have lockable rollers below it. The frames when joined together should form a single frame for the stage and shall be interlockable with leg supports so as to avoid any movement while functioning. It shall have droppable lockable pedestal to support the frame.

Providing and fixing of the HDHMR board with veneer of rate not less than 1500/ psqm glued over the HDHMR Board of 12mm thicknes fixed to the walls on the 48mm GI specially pressed sections complete with insulation of 50mm 1000GSM polyester wool.

Providing and fixing of the Duco paint on the surfaces as desired after making base with NC putty complete.

Providing and fixing of the Nylon woven Carpet of 1200 GSM with designs as selected by the architect complete with laying and floor correction if any required .

Providing and fixing of the 50x12mm HDHMR moldings as per the design drawings duco painted. Duco paint payable searately.

Providing and fixing of the laquer glass with SS spacers as required to be fixed on the wall / partitions as per requirement and design drawings complete.

Providing and fixing Sensor type uniral including cutting and making good the walls and floors wherever required as per direction of Engineer-in-Charge ROCA MAKE EURET URINAL SENSOR (AC) model No. RS35945M000. (Equivalent of Kohler /Grohe)

Providing and fixing of Wall hung European type W.C ,Soft close seat cover , cistern with all fittings and fixtures complete including cutting and making good the walls and floors wherever required: as per direction of Engineer-in-charge . Roca make code No. RS341730000 & RS346477 / (Equivalent of Kohler / Grohe)

Providing and fixing ROCA make gel dispenser wall hung of Hotel's 2.0 model Modle No RA816391001 (or equivalent of Kohler /Grohe) of desired pattern including all accessories as per direction of Engineer-in-charge.

Supply, fixing and testing of Towel ring (ROCA: RA816711001 or Equivalent)

Providing and fixing wash basin OF ROCA MAKE Urbi -6 mm model No. RS32722B000 over the counter i/c bottle trap 32mm (siphon type with 110 mm intel & 330 mm outlet connection pipes of Roca and required fitting and fixtures complete i/c cutting and making good the walls wherever required as per direction of Engineer-in-charge (Equivalent of Kohler /Grohe)

Providing and fixing ROCA make toilet roll holder of Hotel's 2.0 model to the wall Model No. RA816384001 of approved design and make as per direction of Engineer-in-charge. (Equivalent of Kohler /Grohe)

Providing and fixing C.P. brass basin mixer of ROCA Make (EVOL) high neck monoblock basin mixer with POP-up Model No. RT5A3449C00 of approved design & make as per direction of Engineer-in-charge. 15mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of ROCA MAKE (LOFT)code: RT5A1543C00 as per direction of Engineer-in-Charge. a) 15mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of ROCA MAKE 180 degree valve with flange RF525159800 as per direction of Engineer-in-charge.a) 15mm nominal bore

Providing and fixing CP brass health faucet with tube and hook of ROCA MAKE (CHROME) RF9060A1 for EWC Pan complete as per direction of Engineer-in- charge. .15mm nominal bore.

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and FT & FD. Size 100 mm x 100 mm

Providing and fixing GI Gyp steel ultra frame work for wall panelling as per design drawing consisting of floor channel of size 50x32x32 x0.5mm thick at bottom and top fixed with 35 mm nylon sleeves and 35 mm screw. Further fixing GI stud 48x34x36x0.5 mm thick @600mm C/C vertically. The framework to be filled with 50mm 1200GSM non-woven thermal bonded polyester wadding ( Make Nowofill / Himalaya / Gyptech) held in position with 18 mm GI checken mesh of 24SWG with drive all screws and oversize washers. Finally fixing over it horizontally GI stud 48x34x36x0.5 GI stud @600mm C/C or wherever required as per design drawings. The frame to be fixed to the walls by means of angle holdfasts of suitable length out of 35x35x4mm MS angle duly given redoxide and paint complete with expandable anchor fasteners of 65x10mm dia fixed on each vertical member @1200mm C/C.The work shall be executed as per drawings, specifications & instructions of engineer in charge.

Providing and fixing FR ( Fire retarder) ply of required thickness for wall lining with necessary screw, complete as per drawing and direction of Engineer-in- Charge. Recomended Make : Duro , Century , Merino, Green . The ply to be fixed to the existing GI frameowrks ( Frameworks to be paid separately in item no8) at all heights. 8 mm thick ply . The work shall be executed as per drawings,specifications & instructions of engineer in charge.The work shall be executed as per drawings ,specifications & instructions of engineer in charge.

Providing and foxing of the 18% perforations as per the design drawings in the FR ply with CNC machine as per design drawings.

Providing & fixing of Fabrico Acoustic Panel ( make Versatile acoustic/ Himalaya/Gyptech) Composed of glasswool core faced with (Inherently Fire retardant fabric (Nextgen / RSWM) Note: Contractor to give Test certificates) design matte as selected by architect. Density of panel to be not less than 120 KG / Cu mtr. The panel to be glued/ fixed with impalers as per manufacturer recommendations over the perforated 8mm FR ply fixed over GI framework( FR ply & GI framework paid separately ). . The panels in different colours to be cut with Sharp cutter for smoth & perfect edging in shape as per the design drawings. The panels to be further glued to the ply with SH/SR adhesive ( Fevicol/ Araldite / Vamicol). The work to be done complete as per the design & instructions of engineer in charge including accessories as required.

Providing and fixing of the 8mm toughened glass with patch fitting s for the partitions as required complete with accessories

Providing and fixing of the 3 M / Hyundai memberane on the glass as required as per the design selected by the architect.

Providing and fixning of the texture paint of Asian / Spectrum / Berger as selected on the walls after amking the base complete including the top coat etc in the colour as required for the interior walls and areas as per the drawings complete.