India Trade Promotion Organisation Tender

Design, fabrication, supply , errection, testing and commissioning of 16 meter high mast pole of steel in two sections suitable for 50 m/sec wind speed as per IS:875(Part-III) totally hot dipped galvanized as per BS-EN 10025 with raising/lowering type of thickness 4 mm at bottom & 3 mm at top of high mast pole and diameter at top not less than 150 mm and bottom not less than 410 mm & 20 side polygon standard for galvanisation as per BS EN ISO 1461 including opening of door at base of size with 1050 x 250 mm base plate of 540 mm x 25mm thickness , minimum 8 numbers foundation bolts of EN-8 grade as per IS 1367(part 3) suitable for mounting 8 Nos floodlight luminaries in symmetrical arrangement made of 50 NB ERW class B MS pipe welded in 2 sections and electrically operated raising/ lowering system comprising double drum winch, two continuous 6mm dia steel wire rope made of AISI 304 as per IS 2266, 7/19 of breaking capacity 1450 Kg X 2 , trailing cable of size 5 core 2.5 sqmm , connector, integral power tool motor of capacity not less than 1 HP single speed one number as per IS 12615, manual vhandle, junction box, lightning finial, lantern carriage, top pulley arrangement complete including design and construction of shallow foundation with RCC (M-25) grade concrete for the high mast considering the safe soil bearing capacity as per site requirement with all material and labour, fully galvanised foundation bolt manufactured from special steel along with nuts, washer, anchor plate and common template. Power cables from panel to top of High Mast, mounting clamps and bolts, including errection and commissioning including earthing as per BIS and modern engineering practices including providing and fixing of lightening arrestor and LED type single dome aviation obstruction light complete all as specified, Note :- Foundation shall be made as per drawing and design approved by OEM.

Supply and fixing of 200W LED Flood Light with a minimum system lumen of minimum 28000 lumen and efficacy 135 lumen/watt having CCT of 5700K and CRI 70 and 50,000 burning hours @ L70B50. The housing should be of non-corrosive high-pressure die-cast aluminum with PF 0.95, IP 66 with an IK 10. The Luminaire should have a 20 KV SPD. The wattage of each LED should be greater than 1 watt and less than 3 watt. Only high power Single white LED chip with ceramic based suitable for outdoor use is allowed. The Luminaires shall employ Structured LED array for optimized area lighting photometric distribution with individual photometric integrated optics lenses designed to optimize application efficiency and minimal glare achieving wide beam angle, individual Integrated / PC optical lens to be provided on each LEDs on a molded lens plate fixed mechanically. Electronic driver should be IP67 potted with APFC and CISPR 15 compliance with THD 10% and shall have surge protection of minimum 4kV. Input Voltage range 140- 270V. The Driver should be a potted driver, not a printed circuit board without casing, mounted on the luminaries , BIS approved. LM 79 and LM80 reports for OEM in house NABL (not more than 6 months old) accredited lab to be submitted.

Supply and fixing of 100 W LED Flood Light with a minimum system lumen of minimum 12000 lumen and efficacy 120 lumen/watt having CCT of 5700K and CRI 70 and 50,000 burning hours @ L70B50. The housing should be of non-corrosive high-pressure die-cast aluminum with PF 0.95, IP 66 with an IK 07. The Luminaire should have a 10 KV SPD. The wattage of each LED should be greater than 1 watt and less than 3 watt. The Luminaires shall employ Structured LED array for optimized area lighting photometric distribution with toughened glass designed to optimize application efficiency and minimal glare achieving wide beam angle on molded lens plate fixed mechanically. Electronic driver should be APFC based with THD 10% and shall have surge protection of minimum 4kV. Input Voltage range 140- 270V. The Driver should be a potted driver, not a printed circuit board without casing, mounted inside the luminaries, BIS approved. LM 79 and LM80 reports for OEM in house NABL (not more than 6 months old) accredited lab to be submitted.