Guru Gobind Singh Indraprastha University Tender

Providing & Placing Rectangular workstations :Frame Work, Partition and Cable management : Frame work shall consist of main spine and return spine of aluminium extruded section of minimum thickness of 1.2 mm. The overall thinkness of Panel base System should be minimum60-70 mm. The panel will be hollow inside to accommodate wiring for electrical/data and outer frame of panel should be made of extruded aluminium. The panel shall be made up of 3 mm thick MDF both sides of the wooden frame to create the hollow for the wire management. Finishes of panel above the worktop: Above the top fabric pinup+ Glass writable marker board with raceway on main spine. The hollow panel made of MDF and 3mm thick foam which is upholstered with 0.5mm thick fabric with half fabric pinup + half glass marker board. The thickness of main spine partition panel should be minimum60-70 mm & minimum 25-28mmmm thick for return & Aisle spine. Finishes of main spine panel below the worktop: Below the top the hollow panel should be made of MDF tile and 0.5mm thick steel sheet pasted on MDF which is powder coated with EPC finish 80-90 microns for durability on the inside as well on the outside. The panel outer aluminium frame is designed such a waythat it can be easily slide in to the columns/ Connectors by means of stacking one over the other. Horizontal race way should be 150-170 mm height aluminium profile. There shall be complete cable management arrangement with openable raceway above/ below worktop with provision for fitting electrical/data switches and holes for passing cable. Connectors/ Post Description: End Post: Aluminium 60-70 mm width – 1200-1250 mm height. Two way post: Aluminium 30-80 mm width – 1200-1250 mm height. Three way post: Aluminium 30-80 mm width – 1200-1250 mm height. Four way post: Aluminium 30-80 mm width – 1200-1250 mm height. Brackets: Table top supported with 50-60mm width steel bracket. Table top to table top connector: 150-170 mm Width x 120-140 mm Depth width connector. Worktop :Worktop Made of 25mm thick E-1 grade particle board finished with 2mm ABS edge banding. E1 grade laminate with zero urea formaldehyde emissions (or= 8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The exposed edge of worktop shall be secured with 2mm thick PVC edge banding tape of approved colour. The height of Worktop shall be 740-760 mm from ground level. The particle board should be E-1 Grade with pvc edge banding. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Linear Workstation – 1050(L) X 600(D) X 1200(H) Mm - One Seater Cluster One Sided

Providing & Placing Rectangular workstations :Frame Work, Partition and Cable management : Frame work shall consist of main spine and return spine of aluminium extruded section of minimum thickness of 1.2 mm. The overall thinkness of Panel base System should be minimum60-70 mm. The panel will be hollow inside to accommodate wiring for electrical/data and outer frame of panel should be made of extruded aluminium. The panel shall be made up of 3 mm thick MDF both sides of the wooden frame to create the hollow for the wire management. Finishes of panel above the worktop: Above the top fabric pinup+ Glass writable marker board with raceway on main spine. The hollow panel made of MDF and 3mm thick foam which is upholstered with 0.5mm thick fabric with half fabric pinup + half glass marker board. The thickness of main spine partition panel should be minimum60-70 mm & minimum 25-28mmmm thick for return & Aisle spine. Finishes of main spine panel below the worktop: Below the top the hollow panel should be made of MDF tile and 0.5mm thick steel sheet pasted on MDF which is powder coated with EPC finish 80-90 microns for durability on the inside as well on the outside. The panel outer aluminium frame is designed such a waythat it can be easily slide in to the columns/ Connectors by means of stacking one over the other. Horizontal race way should be 150-170 mm height aluminium profile. There shall be complete cable management arrangement with openable raceway above/ below worktop with provision for fitting electrical/data switches and holes for passing cable. Connectors/ Post Description: End Post: Aluminium 60-70 mm width – 1200-1250 mm height. Two way post: Aluminium 30-80 mm width – 1200-1250 mm height. Three way post: Aluminium 30-80 mm width – 1200-1250 mm height. Four way post: Aluminium 30-80 mm width – 1200-1250 mm height. Brackets: Table top supported with 50-60mm width steel bracket. Table top to table top connector: 150-170 mm Width x 120-140 mm Depth width connector. Worktop :Worktop Made of 25mm thick E-1 grade particle board finished with 2mm ABS edge banding. E1 grade laminate with zero urea formaldehyde emissions (or= 8mg/100 g oven dry board-perforated method) for better in-house air quality. This should comply with (EN 120-1992). The exposed edge of worktop shall be secured with 2mm thick PVC edge banding tape of approved colour. The height of Worktop shall be 740-760 mm from ground level. The particle board should be E-1 Grade with pvc edge banding. Drawer Unit : 3 drawer Metal pedestal of overall dimensions internal and external dimensions 380-430 mm (W) x 430-480 mm (D) x 600-620 mm ( H). Drawer body should be made of CRCA of thickness 0.7-0.8 mm duly powder coated with 70-80 micron. Each pedestal should be provided with pencil tray of 40-45 mm(H) x 110-120 mm (D) x 300-310 mm (W).Each pedestal should have 5 Nos castor fitted to it where in one castor will be fitted to lower most drawer to provide extra stability. Linear Workstation – 1050(L) X 600(D) X 1200(H) Mm – Two-Seater Cluster One Sided

Providing and placing of Side board cabinet with storage of size 3500mm (L) X 450mm (D) X 900mm (H). Body panel shall be made with 18mm thick commercial ply with approved shade of 1mm thick lamination. All the exposed edges are as bended with 0.8mm thick PVC edge bending. Body back and drawer bottom shall be made with 8mm thick pre laminated particle board. Top Cornice shall be made of imported HDF foil wrapped decorative trim Hardware : The high quality hardware used like Roller slides, Hinges , minifix, wooden dowels is of make Hettich, EBCO or equivalent.. Lock used for main door is 3 way lock and lock used for drawer is cam lock Construction : Knock Down construction. The Vertical & Horizontal members are connected with special powder coated brackets/dowells/minifix of hettich or ebco make etc all complete and as per direction of Engineer-in-Charge