Guru Gobind Singh Indraprastha University Tender

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete Twin rubber stopper

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.5 mm thick

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. 200 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm sqm

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality oil bound distemper having VOC content less than 50 gm per ltr. of approved manufacturer and of required shade and colour complete. as per manufacturer's specification. One or more coats on old work

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China counter top type wash basin of size 660x460 mm with single 15 mm C.P. brass pillar tap with elbow including operated levers

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing . Rectangular shape 1500x900 mm

Providing and fixing soil, waste and vent pipes : 100 mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing plain bend of required degree. 100 mm dia Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing single equal plain junction of required degree : 100x100x100 mm Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls 20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia Pipes

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing cp brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Supply of Soap dispenser with wall mounting arrangement and manual type square shape Stainless Steel (SS304) for reusable and refillable dispenser pump holds hand soap, lotion or essential oils in a stylish and fashionable container size:- 450-500ml.

Providing and fixing cp brass grab bar 600 mm length of approved quality with fittings and fixing all complete. :25 mm dia bore

Providing and fixing in position restroom/toilet cubicle system having depth minimum 1500 mm at all floor levels complete in all respects as per approved design/architectural drawings and as per the directions of Engineer-in-charge. The cubicle system shall comprise of the following: i) 18 mm thick high pressure laminated board, laminate of any colour/shade as approved by the Engineer-in-charge on both sides of the board, manufactured by Merino or T Line or Greenply as per EN 438-2&3, 2005. Board shall have density of minimum 1350 kg/cum and it shall be water resistant, anti-bacterial and impact resistant. Front panel and divider wall with stripe shoe touching floor (No gap shall be at bottom of divider/front panel except door) ii) SS 316 grade shoe box section at the bottom having dimensions and thickness as recommended by the approved vendor (but minimum 93 mm x 36 mm and minimum 0.8 mm thickness). iii ) SS 304 grade F-profile having dimensions and thickness as recommended by the approved vendor (but minimum 35 mm x 18 mm and minimum 0.6 mm thickness) / H-profile having dimensions and thickness as recommended by the vendor (but minimum 18 mm and minimum 0.6 mm thickness). iv) SS 304 grade U-profile having dimensions and thickness as recommended by the approved vendor (but minimum 21 mm x 18 mm and minimum 0.6 mm thickness). v) SS 304 grade top rail of square box section of size as recommended by the approved vendor (but minimum 40 mm and minimum 0.6 mm thickness). vii) SS 304 grade lock with a handle as per approved vendor's specifications or as approved by Engineer-in-charge. vi) SS 304 grade knob as per approved vendor's specifications or as approved by Engineer-in-charge. viii) SS 304 grade auto reverse ball bearing hinges 3 No of size as recommended by the approved vendor but minimum 76 mm x 53 mm x 2.4 mm. ix) SS 304 grade coat hook as approved by the Engineer-in-charge. x) The cubical unit shall be minimum 5 years guarantee for the board against any moisture and 5 years guarantee for the hardwares. Item/rate includes all accessories etc required for fixing of the urinal partition even if it is not explicitly mentioned in the above description of the item. Nothing extra shall be payable on any account. Contractor shall quote rate accordingly. Note: Only exposed area of laminated board in sqm shall be measured for payment purpose)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. 'Group C

Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. Group C

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. '2 x 1.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. '3 x 1.5 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. '3 x 4 sq. mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. '6 x 4 sq. mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. '20 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. '25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. '20 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. '25 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. '5/6 amps switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. '15/16 amp switch

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. '3 pin 5/6 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. '6 pin 15/16 amp socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. '1 or 2 Module (75mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. '3 Module (100mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. '4 Module (125mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. '6 Module (200mmX75mm)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. '8 Module (125mmX125mm)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. '1 or 2 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. '3 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. '4 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. '6 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required. '8 Module

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and installation of ISI mark heavy duty exhaust fan of 300 mm sweep 230 volt 50 HZ 1400 RPM complete with blade, leg guards, rubber pads, louver etc. in the existing opening including connections, testing etc. as required.

Supplying and fixing of 250 mm sweep, Fresh Air Ventilating fan in plastic body complete with blade, louver etc suitable for 230V A.C. supply, on existing opening including making connection etc. as reqd.

Supply, installation, testing and commissioning of 34 W- 36 W recessed type cool day light 5700/6500 K, full glow LED panel of size 595 mm X 595mm, having minimum system lumen out put of 3600 lumens minimum system efficacy of 100 Lumen/Watt, power factor 0.90, CRI80, THD10 with APFC isolated driver with efficiency of 85% serge protection 2 KV operating voltage 150 to 270 volt, 50 Hz A.C. Supply. Complete with all accessories as per specifications to be fixed in existing Gypsum false ceiling, tightening with suitable M.S. Chain suspension arrangement. LED Chip make- Cree, Nichia, Philips, Lumiled, Osram, Edison, Seoul, Bridge lux, Luminare shall be complying to LM80 Report from LED manufacturer for 50,000 Burning Hrs and LM-79 Report from NABL accredited lab, connection with 3x1.5 sqmm FRLS conductor wire etc, complete as required.

Supply, installation, testing and commissioning of 10 W- 12 W round recessed type LED Down Lighter having minimum system Lumen out put of 1200 Lumen and minimum system efficacy of 100 lumen/Watt in die cast Aluminium heat sink/housing, Colour temperature (5700K to 6500K) power factor .90, CRI80, THD10 with isolated driver with efficiency of 85% surge protection2 KV, Suitable for operation on 150 to 270 volts, 50 Hz A.C. complete with all accessories as per the specifications in the existing Gypsum/Calcium silicate false ceiling and repair of false ceiling/gypsum/calcium silicate etc if any for fixing. LED Chip make- Cree, Nichia, Philips, Lumiled, Osram, Edison, Seoul, Bridge lux, luminare shall be complying to LM80 Report from LED manufacturer for burning life of 50,000 Hrs and LM-79 Report from NABL accredited lab, connection with 3x1.5 sqmm FRLS conductor wire etc, complete as required.

Supply, installation, testing and Commissioning of 18W- 20Watt LED light 4 feet Batten Luminare having minimum system Lumen output of 2000 Lumens, minimum system efficacy of 100 Lumen/Watt, Colour temperature (5700 K to 6500K) in Cool day light, extruded Aluminium housing, Power factor 0.90 CRI80, THD20 with APFC isolated driver with efficiency of 85% Surge protection 2KV, operating voltage 150-270 50Hz AC. With LED chip make : Cree, Nichia, Philips, Lumiled, Osram, Edison, Seoul, Bridge lux, luminaries shall be complying to LM80 Report from LED manufacturer for burning life of 5,0000 Hrs and LM-79 Report from NABL accredited lab, connection with 3x1.5 sqmm FRLS PVC conductor wire etc complete as required.

Supply, installation, testing and commissioning of 15W – 18 Watt back-lit LED light surface mounted fitting in square shape in Aluminium heat sink/housing (300 mm x 300 mm nominal size) having minimum system lumen out put of 1800 lumens, minimum system efficacy of 100 lumen/Watt, Colour temperature 5700K/6500K in Cool Day light. Power Pactor .90, CRI80 etc, completed as required.

Supplying, installation, testing & Commissioning Surface/Wall Mounted integrated LED 2 feet (Nominal size) Fitting of Not more than 10W with Aluminum Extrusion housing & opal diffuser finish , Integral electronic driver with Output short circuit protection, Surge Voltage Protection of min 2 KV and Safety test as per IS15885, total system Lumen 1050 or above in Cool day Light(5700K to 6500K), Power factor0.9, CRI (Ra) 80, System Lumen Efficacy105 Lm/w, THD(%) 10, LED Lamp Make- Cree, Nichia,Philips Lumiled, Osram, Edison, Seoul, Bridgelux, luminaries shall be complying to LM80 Report from LED manufacturer for burning life of 5,0000 Hrs and LM-79 Report from NABL accredited lab, connection with 3x1.5 sqmm FRLS PVC conductor wire etc complete as required.

Dismantling existing various type of light fittings/ ceiling fans/wall fans including disconnections etc complete as required

Credit Items: Taking away the existing material as credit item on buy back basis as required Fittings/Downlighters

Credit Items: Taking away the existing material as credit item on buy back basis as required Wire/Conduit etc

Credit Items: Taking away the existing material as credit item on buy back basis as required Switch & Socket with plate/Industrial Socket/Fan regulator with plate/ Tel Socket with plate

Credit Items: Taking away the existing material as credit item on buy back basis as required Ceiling Fan/Wall fan/Exhaust Fan