Guru Gobind Singh Indraprastha University Tender

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) sqm

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Providing and fixing Stainless steel grade SS304 sliding door bolts nuts and SS screws etc. complete

Providing and fixing Stainless steel grade SS304 tower bolts with necessary SS screws etc. complete

Providing and fixing Stainless steel grade SS304 handles with necessary SS screws etc. complete

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Providing and fixing of compactors/optimizer comprising of single last, single static and twin mobile units duly fixed on rail channel as per manufacturer specification as per approved layout and as per specifications all complete as per directions of Engineer-in-Charge. The compactor/optimizer should be in rigid knock down construction made out of 0.8 mm thick CRCA steel sheet conforming to IS:513 Grade D. Each unit has 5 loading lovels formed by 4 nos. adjustable shelves. Body and shelves are given anti rust treatement and are powder coated with apoxy polyester powder of approved shade and colour with dry film thickness of 40 micros. The powder coating involves 8 steps treatment consisting of hot water rinse, knock of degreasing, cold water rinse, phosphating, cold water rinse, passination and dry off oven treatment. Final finish consists of epoxy polyester powder coating. The material is then oven baked with controlled temperature of 180°C to 200°C. Shelve is made of 0.8 mm thick CRCA steel sheet conforming to IS:513 Grade D designed for maximum load bearing capacity of 80kg UDL per shelf Shelves are mounted on brackets and shelf level can be adjusted at appprox 25 pitches. There are 4 adjustable shelves per body giving 5 loading levels. The under carriage is welded frame made of HR Sheet 3.15 mm thick conforming to IS : 10748 suitable fabricated to take loads based on configuration. The under carriage after pre treatment is coated with final finish consisting of epoxy polyster powder coat of approved colour and shade with a drawing film thickness of minimum 40 micros. Guide channels consists of 'J' section 2 mm thick HR sheet and 25mm square bright bar - both connected by screws. The guide channels should have stoppers to prevent derailment. A centralized locking arrangement is provided through locking stiffner mounted on back of single last unit so that it gets locked on channels when all units are brought together. The recess handle lock is placed at suitable height. The movement shall be drive type configuration achieved mechanically through a polyurethane drive wheel and sprocket - chain-tensioner arrangemnt mounted rigidly on body side. The drive wheel should have locking arrangment. The under carriage shall be provided with. minimum 2 rollers on shaft for driving, minimum 2 antifriction ball bearing for rolling and minimum 4 antifriction ball bearing for guiding between rail. Locking knob to be provided for manual locking of individual units while in use. Each unit should be provided with label holder of acrylic sheet. 2 Bay Single Fix minimum 455 x 910 x 1980

Providing and fixing of compactors/optimizer comprising of single last, single static and twin mobile units duly fixed on rail channel as per manufacturer specification as per approved layout and as per specifications all complete as per directions of Engineer-in-Charge. The compactor/optimizer should be in rigid knock down construction made out of 0.8 mm thick CRCA steel sheet conforming to IS:513 Grade D. Each unit has 5 loading lovels formed by 4 nos. adjustable shelves. Body and shelves are given anti rust treatement and are powder coated with apoxy polyester powder of approved shade and colour with dry film thickness of 40 micros. The powder coating involves 8 steps treatment consisting of hot water rinse, knock of degreasing, cold water rinse, phosphating, cold water rinse, passination and dry off oven treatment. Final finish consists of epoxy polyester powder coating. The material is then oven baked with controlled temperature of 180°C to 200°C. Shelve is made of 0.8 mm thick CRCA steel sheet conforming to IS:513 Grade D designed for maximum load bearing capacity of 80kg UDL per shelf Shelves are mounted on brackets and shelf level can be adjusted at appprox 25 pitches. There are 4 adjustable shelves per body giving 5 loading levels. The under carriage is welded frame made of HR Sheet 3.15 mm thick conforming to IS : 10748 suitable fabricated to take loads based on configuration. The under carriage after pre treatment is coated with final finish consisting of epoxy polyster powder coat of approved colour and shade with a drawing film thickness of minimum 40 micros. Guide channels consists of 'J' section 2 mm thick HR sheet and 25mm square bright bar - both connected by screws. The guide channels should have stoppers to prevent derailment. A centralized locking arrangement is provided through locking stiffner mounted on back of single last unit so that it gets locked on channels when all units are brought together. The recess handle lock is placed at suitable height. The movement shall be drive type configuration achieved mechanically through a polyurethane drive wheel and sprocket - chain-tensioner arrangemnt mounted rigidly on body side. The drive wheel should have locking arrangment. The under carriage shall be provided with. minimum 2 rollers on shaft for driving, minimum 2 antifriction ball bearing for rolling and minimum 4 antifriction ball bearing for guiding between rail. Locking knob to be provided for manual locking of individual units while in use. Each unit should be provided with label holder of acrylic sheet. 2 Bay Double Movable minimum 910 x 910 x 1980

Providing and fixing of compactors/optimizer comprising of single last, single static and twin mobile units duly fixed on rail channel as per manufacturer specification as per approved layout and as per specifications all complete as per directions of Engineer-in-Charge. The compactor/optimizer should be in rigid knock down construction made out of 0.8 mm thick CRCA steel sheet conforming to IS:513 Grade D. Each unit has 5 loading lovels formed by 4 nos. adjustable shelves. Body and shelves are given anti rust treatement and are powder coated with apoxy polyester powder of approved shade and colour with dry film thickness of 40 micros. The powder coating involves 8 steps treatment consisting of hot water rinse, knock of degreasing, cold water rinse, phosphating, cold water rinse, passination and dry off oven treatment. Final finish consists of epoxy polyester powder coating. The material is then oven baked with controlled temperature of 180°C to 200°C. Shelve is made of 0.8 mm thick CRCA steel sheet conforming to IS:513 Grade D designed for maximum load bearing capacity of 80kg UDL per shelf Shelves are mounted on brackets and shelf level can be adjusted at appprox 25 pitches. There are 4 adjustable shelves per body giving 5 loading levels. The under carriage is welded frame made of HR Sheet 3.15 mm thick conforming to IS : 10748 suitable fabricated to take loads based on configuration. The under carriage after pre treatment is coated with final finish consisting of epoxy polyster powder coat of approved colour and shade with a drawing film thickness of minimum 40 micros. Guide channels consists of 'J' section 2 mm thick HR sheet and 25mm square bright bar - both connected by screws. The guide channels should have stoppers to prevent derailment. A centralized locking arrangement is provided through locking stiffner mounted on back of single last unit so that it gets locked on channels when all units are brought together. The recess handle lock is placed at suitable height. The movement shall be drive type configuration achieved mechanically through a polyurethane drive wheel and sprocket - chain-tensioner arrangemnt mounted rigidly on body side. The drive wheel should have locking arrangment. The under carriage shall be provided with. minimum 2 rollers on shaft for driving, minimum 2 antifriction ball bearing for rolling and minimum 4 antifriction ball bearing for guiding between rail. Locking knob to be provided for manual locking of individual units while in use. Each unit should be provided with label holder of acrylic sheet. 2 Bay Single Movable minimum 455 x 910 x 1980

Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Fire retardant plywood conforming to IS: 5509

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick