Directorate General Defence Estates Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Costs
EMD
₹ 80,000Document Cost
₹ 2,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_DGDE_684954_1Tender No
DCB/8/E-M/C-16/2024-25Tender Authority
Directorate General Defence Estates ViewPurchaser Address
-Website
http://defproc.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Submersible Motor 2 H.P. single phase any make
4
-
-
ditto- as explained here-in-before in item No. 1 above but rate include the repair to the submersible pump by replacing defective parts by new one of existing quality.
-
-
-
Submersible pump 10 HP 8 Stage
3
-
-
Submersible pump 7-1/2 HP 6 Stages
1
-
-
Submersible pump 2 H.P 14 Stage
4
-
-
Supply connecting testing and commissioning submersible cable with copper conductor,1100 V grade stranded of size 4 Sqmm (Finolex) cross sectional area (Nominal) 3 core all as specified and as directed.
1200
-
-
All as per item No. 3 but 2.5 Sqmm cross sectional area
500
-
-
Disconnecting existing defective electric motor pump set of any make 2 HP to 5 HP from electric mains isolating the necked connections removing from foundation by unscrewing the nuts, bolts etc. dis-couple from pump opening of motor for inspection in presence of JE/Engr.-in-Charge & carry out minor repairs at site re-assembling the motor after repair, re-fixing in position, re-connecting same as prior to removing from foundation including replacement of nuts, bolts washers of suitable size, testing and commissioning complete all as specified and directed .
6
-
-
Taking out old unserviceable/burnt copper winding of the following motors (defective motor taken out in item 5 above) and material and labour rewinding of elect motor of following capacity with super enameled copper winding wire of suitable existing gauge including cleaning of motor, slots, all winding/insulations material varnishing etc. complete all as specified and as directed.
-
-
-
Any make and type elect motor 3 phase 440 volts 5 HP
1
-
-
Any make and type electric single phase 2 HP
4
-
-
Replacement of following parts to the electric motor as shown against each in repairs opened in item No.5 herein before all as specified including all material & labour T & P required for the same as directed.
-
-
-
Ball bearing for elect motor 5 HP 440 V
4
-
-
do- but 2 HP motor
4
-
-
Taking out existing unserviceable/ defective following parts from 5 HP centrifugal pump of any make & size and S & F following parts in the pump all as specified and as directed:
-
-
-
M S Shaft
2
-
-
Ball bearing including greasing
4
-
-
Gun Metal Neck Ring
4
-
-
Gun Metal Bushes
4
-
-
Water seal
4
-
-
C I Check nuts
6
-
-
Impellor bronze
4
-
-
Taking out existing unserviceable/ defective following parts from 2 HP of centrifugal pump of any make and S & F the following parts by new one all as directed
-
-
-
M S Shaft
2
-
-
Ball bearing including greasing
4
-
-
Check ring
4
-
-
Check nuts
6
-
-
Impellor bronze
2
-
-
Water seal
4
-
-
Disconnecting, isolating, electrically star delta/DOL u/s Starter 3 phase 440 volts of any make & type and taking down from wall/panel board keeping aside for disposal all as specified and as directed.
2
-
-
Supply, installation connecting, testing and commissioning star delta starter 3 phase 440 volts automatic complete with no volt relay, over load protection, duty mounted on angle iron frame grouted stiff in wall complete as specified and as directed for the following size of motor
-
-
-
10 to 12 HP 3 phase
2
-
-
7.5 HP 3 phase
1
-
-
Supply, installation, testing, connecting and commissioning DOL starter 3 phase 440 volts with no volt relay, over load protection duly mounted on angle iron frame of suitable size grouted in wall complete for upto 7.5HP 3 phase electric motor all as specified. All incoming connection shall be done with single core PVC insulated stranded copper conductor cable of suitable size including lugs, nuts bolts, washers etc and the rate shall deem to be included in this item.
2
-
-
Disconnecting, electrically the u/s switch fuse of any make & type and taking down and supply, fix and connect switch fuse ICTPN with kit kat fuse rewire able type 440 volt complete conforming to relevant IS of approved make all as specified including all connecting and jointing material for the following capacity.
-
-
-
200 Amp
1
-
-
100 Amp
1
-
-
63 Amp.
1
-
-
Disconnecting, electrically, the switch change over of any make & type and supply fix and connect switch change over ICTPN 4 pole conform to IS of approved make including all connecting and jointing material all as specified for the following capacity
-
-
-
200 Amp 440 Volt
1
-
-
100 Amp 440 Volts
1
-
-
Replacing of following component of electric control panel of existing quality by taking out old and unserviceable and making the panel fully functional
-
-
-
Contactor ML-1.5
3
-
-
Contactor ML-1.0
3
-
-
Contactor ML0
3
-
-
Contactor MK-1
2
-
-
Over load relay of range 6 to 10
3
-
-
Over load relay of range 9 to 14
3
-
-
Over load relay of range 14 to 23
3
-
-
Timer GT 200
3
-
-
Volt meter 0-50
3
-
-
Ameter- 0-30
3
-
-
Ameter- 0-60
3
-
-
Ameter- 0-100
3
-
-
Contactor MNX – 32
2
-
-
Transportation at site of work Air compressor of 450 CFM at various locations of tube wells in Delhi Cantonment area for cleaning of existing borehole of dia ranging from 200 to 300 mm and removal of compressor after completion of job.
26
-
-
Taking out from the existing bore hole by disconnecting from the starter electrically, disconnecting the water connection carefully by unscrewing the nuts bolts the submersible pump set of various capacity, including column pipe and submersible cable for cleaning and removing silt form the borehole . Taking down/lowering after cleaning in the borehole, submersible pump and column pipe and cable including replacing damaged/rusted column pipe and making the pump fully functional as specified and directed by Engineer-in- charge
26
-
-
M/L cleaning and removing soil from bore hole with the compressor of rating 450 CFM by running the compressor upto 72 hrs . Removing the compressor after completion of job. Job include all the required tools and manpower including removal of surplus soil.silt from the site as specified and directed by Engineer-in-charge.
26
-
-
Digging of borewell by vockey tool steel wire manually or mechanically and deepening the borewell and taking out the dug material out through vockey. Job includes removal of surplus soil material from the site and depositing where directed.
26
-
-
M/L Masonary chamber 90 cm x90 cmx100cm with class designation 75 brick work in cement mortar 1:4 ( 1 Cement :4 Coarse sand) for sluice valve , with CI surface box 100 mm top dia 160 mm bottom dia and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix type B-1, necessary excavation, foundation concrete 1:4; Type D-2 and inside plastering with cement mortar 1:3(1 cement :3 Coarse sand) 15 mm thick finished with a floating coat of neat cement complete as per standard design as specified/directed by Engineer –in- charge.
5
-
-
S/f housing clamp for 80 mm dia pipe with 15 mm dia bolts nuts fabricated from S flat of 50x6 mm all as specified and directed by Engineer –in- Charge.
10
-
-
Supplying /fixing main switch TPN 63 Amps. Suitable for 415 volts including making connections.
2
-
-
S/F assembling, lowering, commissioning and testing of submersible pump set suitable for discharge of 4000 gallons per hour at 100 mt head make BS/ Kirloskar/KSB tied with steel wire rope top to bottom to secure the pump set complete, the pumps shall be lowered in the borewell alongwith steel wire rope & size 10mm dia for securing the pumps properly
2
-
-
ditto- butsuitable for discharge of 3000 gallon at 90 mt head -ditto
2
-
-
S/F of LT control panel of 400/440 volts 50 HZ made out of 1.6mm thick MS sheet with spray painting with synthetic enameled paint suitable to mount on floor and consisting of the following:-a. Bus-bar TPN 100Amps - 1 Set
b. MCCB 63Amps - 2 No.
c. MCCB 32 Amps - 2 No.
d. Star-delta starter fully automatic suitable for 10 HP Motor - 1 No.(L & T)
e. Single phase preventor suitable for 10 HP motor.
f. Pump guard for the protection against single phasing reverse running over loading reverse running. - 1 No.
g. Volt meter 0-500volts range with selector switch. - 1 No.
h. Ameter meter 0-60 amp with CT’s & with selector switch - 1 No
i. Indicating lamp with bulb complete – 1 set. j. Single phase preventor VSP – 2 - 1No. k. Central copper cable of suitable size for inter connection of panel accessories - 1 Job
4
-
-
S/F of CI Sluice valve 100 mm dia with nut bolts packing complete as specified and directed by Engineer-in-charge
4
-
-
S/F of CI sluice valve 150 mm dia with nut bolts, packing complete as specified and directed by Engineer-in-charge.
2
-
-
Repair to the shredding machine including rewinding by taking out old burnt copper winding, cleaning of slots motor, insulating material etc and winding with super enamelled copper wire of existing guage includign replacement of non working parts and blade etc complete all as specified and directed by Engineer-in-charge
4
-
-
Replacement of blade of shredding machine existing shape size and quality as specified and directed by Engineer-in-charge.
8
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%