Delhi Tourism And Transportation Development Corporation Tender

Library Table: Providing and fixing table of size (W1800 X D900 X H750) mm with work top made of 25mm thickness Ply board with two longer edges post formed and two shorter edges with 2 mm thick PVC edge bending ,work top clad with 0.6 mm thick decorative laminate on front as per standard and back side with 0.6 mm white balancing. Table shall have two  'U' shape loop legs made of welded prime quality CRCA steel joined to rectangular ERW tubular frame of 60x30mm /50x50mm size and of 1.6mm thickness as per IS : 3074/05 grade ERW 1. All legs have level adjuster PVC shoes with plastic colour shoes cap, both legs jointed by rectangular tubular pipe of minimum 40x20mm size and 1.6mm thickness. All CRCA steel components / parts shall be epoxy polyester powder coated using the pre-treatment process with the powder thickness greater than 50 micron DFT (Dry film thickness), star perforated design on metal modesty of thickness 1.0 mm fixed on leg on front side of table.                                                  

Conference Table : Providing and Placing in position 14 Seater Conference Table. Overall size shall be 4200 Width mm x 1200 Depth mm x 750 Height mm . Top shall be Base material shall be 18 + 12 mm MDF board. There shall be natural veneer of minimum thickness of 0.6 mm on top surface and balancing 0.6mm laminate on bottom surface . edges shall be machine cut - PU Matt polish and veneer portion of work surface is finished in PU Matt polish . The understructure legs shall be made from 1.6 mm Matt finish silver Anodized Aluminium extrusion/ 25mm thick MDF board finished with natural veneer of minimum thickness 0.6mm on both sides finished in PU Matt polish . Legs assembled together with a plastic / ms glide holder at bottom and 5 mm HR steel shall be powder coated . Provision of wire carrying raceway under table top shall be kept . 2 nos flip top box shall be made of matt silver anodized aluminium extrusion. Powder coated switch mounting tray made from 0.8 mm and 1.2 mm CR steel IS:513 .Switches shall be mounted on tray as per requirement and provision for mounting 8 module switch plate on switch mounting tray shall be made

Reception Table: Providing and Placing in position Reception Table in two arcs. Each arcs shall consists of : Work Top shall be made of 18 mm thick plywood with 0.6 mm lamination , inside radius - 700 mm , outside radius - 1350 mm and depth - 650 mm . Glass shall be Fostered 10 mm thick diamond cut finishing on edges, inside radius shall be – minimum 1200 mm, minimum outside radius - 1400 mm and depth - 200 mm. The Modesty Panel shall be MS Perforated sheet below work surface: 0.8 mm (thick) x 665 mm (height) x 1345 mm (flat length). Above Work surface: 0.8 mm (thick) x 260 mm (height) x 1345 mm (flat length). The legs shall be of MS tube 1.6 mm thick diameter 50.8 mm and height 604 mm.

6 Seater Dinning Table: Providing and Placing in position 6 Seater Dinning Table of minimum Size 1740mm(L) x 1175mm(D) x 750mm(H). Table Work Surface shall be made from 25mm Thick MDF Board which is PU Coated of minimum 2H Hardness with 75% glass, Combination color graphic on the centre shall be provided /1mm thick glossy laminate with 2mm PVC edge bending,0.6mm laminate on bottom with round corner for comfort. Understructure leg and leg connector of the table is made of MS powder coated Bend Pipe of Dia 38mm x 2mm /50x50 mm Thickness complete all as per the direction of Engineer-In-charge.

4 Seater Dinning Table: Providing and Placing in position 4 Seater Dinning Table of minimum Size 1135mm(L) x 1175mm(D) x 750mm(H). Table Work Surface shall be made from 25mm Thick MDF Board which is PU Coated of minimum 2H Hardness with 75% glass, Combination color graphic on the centre shall be provided /1mm thick glossy laminate with 2mm PVC edge bending,0.6mm laminate on bottom with round corner for comfort. Understructure leg and leg connector of the table is made of MS powder coated Bend Pipe of Dia 38mm x 2mm /50x50 mm Thickness complete all as per the direction of Engineer-In-charge.

High Back Chair : Providing and placing in position revolving executive High Back Chair. The seat and back are made up of 1.2cm thick hot pressed plywood confirming to IS 303 and upholstered with pure leather and moulded Polyurethane foam. The back is designed with contoured lumber support for extra comfort. The minimum Back size shall be 53.0cm(W) X 91.0cm(H) and minimum Seat size shall be 53.0cm(W) X 49.0cm(D). High Resilience(HR) Polyurethane foam is moulded with minimum density=40 kg/m cube and hardness load 16+/-2 kgf as per IS:7888 for 25% compression. The seat and back are arrested together with a spine made of minimum 0.8cm thick HR steel with black coated(DFT minimum 50microns). The armrest assembly should be made up of armrest tube, PU armrest and the armrest top. The chair has Front Pivot Synchro Tilt Mechanism having following features - 360 degree Revolving type, Seat back minimum tilting ratio 1 : 1.5, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 5-position locking with anti-shock back mechanism which prevents the backrest from impacting the user when the lock is released, The armrest tube assembly consists of 3 parts - The armrest support tube, PU armrest and armrest top. The armrest assembly is made of 2.54cm+/-0.03cm x 0.16+/-0.0128cm M.S. E.R.W. support tubes and Chrome plated as per IS 1337:1993 having Chrome Thickness of 0.3 To 1 Microns and Nickel Plating Thickness of 10 To 20 Microns /SS tube of dia 28.5mm of 0.16mm thick.. The PU armrest is made of black integral skin polyurethane with 50-70 shore 'A' hardness and reinforced with MS insert. The armrest top is made of ABS /plywood & upholstered with foam & pure leather. The pneumatic height adjustment has an adjustment stroke of minimum 6.5+/-0.3cm. The pneumatic hydraulic lift shall confirm to BIFMA standard and have BIFMA mark. The bellow is 1 piece and blow moulded in black Polypropylene. The pedestal is made of Die-cast aluminium with buffing finished /CRCA pipe 65 *15*1.6 thick with crome finish and Chrome plated as per IS 1337:1993 having Chrome Thickness of 0.3 To 1 Microns and Nickel Plating Thickness of 10 To 20 Microns. It is fitted with 5nos. twin wheel castors. The pedestal is 67.0+/-0.5cm with pitch-center diameter of 77.0+/-1.0cm with castor. The twin wheel castors are injection moulded in Black Nylon complete all as per the direction of Engineer-in-charge.

Chair mid back : Providing and Placing in position mid Back Chair. The seat & back shall be made up of 1.2+/-0.1cm thick hot pressed plywood and upholstered with synthetic leather and moulded polyurethane foam. The back ply and foam is designed with contoured lumbar support for comfortable seating posture. The moulded HR polyurethane foam shall be of minimum density 45 kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The minimum dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 76.0Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a fixed type 1.6 mm thick M.S tubular /CRCA pipe armrest support chrome plated and Chrome plated as per IS 1337:1993 having Chrome Thickness of 0.3 To 1 Microns and Nickel Plating Thickness of 10 To 20 Microns. The mechanism of the chair shall have following features : 360⁰ revolving type, Front pivot synchro mechanism, Tilt tension adjustment, Single point control, 4 position locking with anti shock feature, Seat/Back tilting ratio of 1:2.The chair shall be provided with pneumatic height adjustment which shall have stroke of minimum 6.5 cm. The pneumatic hydraulic lift shall confirm to BIFMA standard and have BIFMA mark. The pedestial shall be fabricated from 0.2+/-0.02cm thick HR sheet, (minimum weight of metallic part of pedestal 3.6 kg ) chrome plated and Chrome plated as per IS 1337:1993 having Chrome Thickness of 0.3 To 1 Microns and Nickel Plating Thickness of 10 To 20 Microns and assembled with injection moulded black polypropylene hub cap and 5 no. twin wheel castor. The minimum size of the pedestal shall be 66.0+/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon. Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0cm as measured from pedestal below. Height from ground - min 102.5 to max 111.5cm. Seat height - min 46.0 to max 55.0cm.

Training Chairs : Providing and Placing in position Training Chairs. The seat and back shall be made up of 1.2+/-0.1cm thick hot pressed plywood as per IS 303 and shall be laminated with natural veneer in three different 'Shades of Teak & Mahogany. “The minimum dimensions of back shall be: 42.0cm. (W) X 45.0cm. (H) and of seat shall be: 44.0cm. (W) X 40.0cm. (D). The armrests shall be made from Laminated veneered plywood (Teak stained) with melamine finish. The understructure shall be made of M.S tube dia1.9+/-0.02cm. x 0.16 ±0.0128cm. thk. and black powder coated (DFT 50 microns). The desklet shall be fixed to a retractable type mechanism & made of 1.8±0.05cm thk Medium Density fiberboard and membrane formed with black 0.04cm thick PVC film. The bottom side shall be provided with black backing laminate. The retractable mechanism enables the user to fold the desklet on the RH side of the chair when not in use. The size of Desklet shall be: 34.5±0.1cm. (W) X 26.5±0.1cm. (D). The paper tray shall be made ofdia0.4+/-0.005cm. M.Swire spot welded to form mesh. It shall be black powder coated (DFT 40-60 microns). The size of paper tray shall be 35.0±1.0cm. (W) X 36.0±1.0cm. (D). X 12.5±1.0cm.(H). Overall Dimensions of Chair shall be Seat Height - 45.5 cm, Height - 86.0cm, Width & Depth of Chair as measured from pedestal - Width-57.0cm(desklet in use) 59.0(desklet folded) and Depth-65.0 cm.(desklet in use) 55.0cm.(desklet folded).

Dinning Chairs : Providing and placing in position Dinning Chairs having Seat/Back and legs without any joint and made of injection moulded high impact strength polypropylene polymer with indoor grade UV resistence glass filled. Minimum Seat Size : 40.6 cm(W) x 43.2 cm(D), Back Size : 51.6cm(W) x 40.5cm(D) .Total height of chair shall be 83.8 cm. Minimum weight of chair shall 3.75 Kg Understructure : complete all as per the direction of Engineer-In-charge.

3 Seater Sofa: Providing and placing 3 Seater Sofa of minimum Size - 2000mm(L) x 920mm(D) x 820mm(H) with Seat Height - 450mm, Seat shall be made of PU foam with minimum density 32 Kg/cum. with two additional top layer of PU Foam with minimum Density 28 Kg/cum Seat is upholstered with synthetic leather and Back and sides shall be made of PU foam with minimum density 28 Kg/cum with two additional top layer of PU Foam with minimum Density 23 Kg/cum Back and sides is upholstered with synthetic leather. The Understructure shall be made up of 1.2+/-0.1 cm thick Hot pressed plywood. Spring assembly of 4mm Dia is mounted in understructure for support and additional cushioning purpose. Legs shall be provided made of Stainless Steel (Grade SS 202). Its is a welded assembly made by the combination of Tube and Plate complete all as per the direction of Engineer-in-charge.

1 Seater Sofa: Providing and placing 1 Seater Sofa of minimum Size - 860mm(L) x 920mm(D) x 820mm(H) with Seat Heigh - 450mm, Seat shall be made of PU foam with minimum density 32Kg/cumwith two additional top layer of PU Foam with minimum Density 28Kg/cum.Seat is upholstered with synthetic leather and Back and sides shall be made of PU foam with minimum density 28Kg/cum with two additional top layer of PU Foam with minimum Density 23 Kg/cum Back and sides is upholstered with synthetic leather. The Understructure shall be made up of 1.2+/-0.1 cm thick Hot pressed plywood. Spring assembly of 4mm Dia is mounted in understructure for support and additional cushioning purpose. Legs shall be provided made of Stainless Steel (Grade SS 202). Its is a welded assembly made by the combination of Tube and Plate complete all as per the direction of Engineer-in-charge.

Center Table : Providing and Placing in position Center Table. Overall minimum size shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm. Top shall be made of glass which shall be 12+/-0.3mm thick tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 mm /rectangular 25*10mm of 1.5mm thick as per relevant IS

Side Table : Providing and Placing in position Side Table. Overall minimum size shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm. Top shall be made of glass which shall be 12+/-0.3mm thick tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 mm /rectangular 25*10mm of 1.5mm thick as per relevant IS code

Double Bed with Bed Side Table : Providing and Placing in position Double Bed of Overall size 2100mm(L) x 1800mm(W) x 900mm(H) and 2Nos Bed side Tables. The complete Bed shall be made from Sheesham /steam Beach Solid Wood and 19mm thick Plywood is provided at the lying surface. Headboard is of size 1900mm(L) x 900mm(W) x 100mm(Thick), Leg Board is of size 1900mm(L) x 450mm(W) x 100mm(Thick), Side rails are of sie 2000mm(L) x 380mm(W) x 50mm(Thick). Ply is provided at the lying surface area of size 2000mm(L) x 900mm(W). The Bed side Tables are made of 18mm thick plywood of overall size 450mm(W) x 450mm(D) x 420mm(H). The Bedside Table is provided with 2 Drawers with handless design to give rich look complete all as per the direction of Engineer-in-charge.

Bed: Providing and Placing in position Bed with laminate finish. Overall minimum size shall be 2050.0 mm L x 1570.0 mm W x 980.0 mm H. Bed Structure shall be made of metal frames made of M.S. 25 mm Square Pipes in 1.2 mm Thickness & M.S. Channels in 1.0 mm thickness. Plinths / Mattress panel shall be made of 19 mm Thick plywood Board. Head board , Tail board and side board shall be made of 25 mm thick plywood . All exposed plywood surface will have 1.0 mm thick laminate with 2 mm thick PVC edge bending with balancing laminate of 0.6mm .

Bed Side Table: Providing and Placing in position Bed Side Table. Overall size shall be minimum 450.0 mm D x 450.0 mm W x 500.0 mm H. Top panel shall be made of 25 mm and Drawer fronts shall be made of 18 mm PVC membrane pressed MDF. Body and drawer panels shall be made of 18 mm thick MDF Board. All the exposed surface shall be 1.0 mm thick laminate and with 2 mm thick PVC edge banding.

Wardrobe: Providing and Placing in position Wardrobe. Overall, minimum size of the wardrobe shall be 1800 W x 500 D x 1900 H mm. All Body panels, drawer, Door panels shall be made of 19 mm thick plywood board. All the exposed surface shall be with 1.0mm thick laminate. All the exposed edges shall be edge banded with 2 mm thick PVC edge banding. Back body and drawer bottom shall be made of 8 mm thick plywood. Mirror used on middle doors shall be 4 mm thick .Complete item shall as per the direction of Engineer-in-charge.

Dressing Table with Stool: Providing and Placing in position Dressing Table with Stool. Overall size of the dressing table shall be minimum 450 W x 450 D x 1700 H and of stool shall be 350 W x 320 D x 450 H mm. Panels of the dressing table and stool shall be made of 18 mm thick MDF Board. .. Top panel of the table shall be made of 25 mm thick MDF. Door of table shall be made of 18 mm thick MDF. Mirror panel shall be made of 18 mm thick MDF board with 4 mm thick mirror fixed on it. All the exposed surface shall be with 1.0mm thick laminate. All the exposed edges shall be edge banded with 2 mm thick PVC edge banding Supporting pipe used for fixing the mirror frame shall be made of MS square pipe of 1.2 mm thickness. Stool seat shall be made of foam with approved quality of fabric wrapped on it.

Workstations: Providing and placing of panel & sliding tile based modular workstations of 1200 mm height as per BIFMA standards, with minimum partition panel thickness of 52.4 mm thick including powder coated aluminum trims and supported on Legs for better air circulation and helps in keeping floor clean. The product should be complete and as per the approved design and direction of Engineer-In-charge. Panels / End Panels Construction - Each panel consists of Vertical extrusions 2Nos and Horizontal extrusions made of minimum 1.2mm thick aluminum /CRCA with powder coated at every division of tile/block . Each panel have Bottom frame fabricated for minimum 52.4mm panel.The complete frame shall be powder coated with minimum 50 microns thickness of epoxy powder coating. The panel blocks shall comprise of decorative prelaminated and balancing 9mm MDF . Each Panel consists of 2Nos Intermediate blocks. Each Panel consists of top tiles/split tiles. These tiles shall slide in to the panels from top before fixing the top horizontal. In case of split tiles, it shall in Fabric magnetic tiles, Whiteboard tiles. Each Panel consists a bottom tile. These bottom tiles shall be slide fitted on to the assembly frame of the panel .All partitions and side panels have leveling screws for adjustment in case of Uneven floor to take care of +/- 25 mm of uneven flooring. Split Tile Finishes : Fabric Magnetic Tiles: Fabric magnetic tiles shall be fabric upholstered metal tiles in 0.6 mm thick G.I. Grade O as per IS: 277. The fabrics shall be upholstered with adhesives. • Fabric slide Tiles: Fabric tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with P.E. foam in the tile for tackablity. The fabric shall be upholstered with adhesives. • White Board Tiles : White board tiles shall be made of 9.0 mm thick pre laminated MDF having all its edges with minimum 0.5 mm thick PVC edging. Aluminium Trims : The top trims and end trims shall be made from aluminum extrusion. All kinds of extrusions shall have average wall thickness of 1.2 mm with powder coat finish. Top trim shall be press fitted on the horizontal extrusion, it shall be slide fitted with the help of top trim connector made from PP copolymer 3530 grade. End trim shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513/ Aluminum powder coated . Wire Management - Wires shall be taken into the system through cable ducts /one raceway from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Wires runs through the system from Bottom tile and extended to the top at various locations . Work surface : Worktop shall be made out of 25mm thick prelaminated Exterior Grade MDF board. All the open edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. Work surfaces are fitted to the panels by work surface brackets. Brackets are made of 2.0mm thick CRCA grade D steel as per IS : 513. Brackets are slide in between end trim and vertical extrusions. Mobile Drawer : Mobile Drawer Unit shall have 3 Drawers Unit with flat metal front and top with Central locking. The Drawer Unit consistes of 2Box and 1File Drawers. The Overall minimum size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction & Material of Drawer Unit : 18 mm thick prelamianted MDF board with 2mm thick PVC edge bending /Welded Assembled of 0.8 thick CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom, ,Top Stiffener & Bottom stiffener1.2 thick CRCA powder coating. All Drawers with Double extension /telescopic precision ball slide shall be provided. For Drawer pulling, handle /side wise tapered recess provided in shell behind Drawer Fronts. Locking:10 lever Cam Lock & Central Right Hand locking with actuator & lock channel mechanism. Castors : Swiveling 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the minimum thickness of 50 microns. Key Board Pullout Tray : Supplying and Fixing of sliding computer key board tray of 480mm (L) X 280mm (D) X 40mm(H) made out of CRCA steel as per IS : 513 made of 0.9mm thick powder coated with sliding channels and other fixing fittings. It should also have a sliding system for accommodating mouse. CPU Trolley : Supplying and Fixing of CPU Trolley of Size - 345mm(W) x 226(D) x 180mm(H) is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. It consists of 4Nos Non-lockable twin wheel castors made of injection moulded in Black Nylon.

(i)Work Station 1500 W1 x 1350 W2

(ii) Work Station 1200 W1 x 600 W2

Interaction desk : Providing and placing of panel & sliding tile based modular workstations of 1200 mm with front panel of 900 mm height as per BIFMA standards, with minimum partition panel thickness of 52.4 mm thick including powder coated aluminum trims and supported on Legs for better air circulation and helps in keeping floor clean. The product should be complete and as per the approved design and direction of Engineer-In-charge. Panels Construction - Each panel consists of Vertical extrusions 2Nos and Horizontal extrusions made of minimum 1.2mm thick aluminum /CRCA with powder coated at every division of tile/block . Each panel have Bottom frame fabricated for minimum 52.4mm panel. The complete frame shall be powder coated with minimum 50 microns thickness of epoxy powder coating.The panel blocks shall comprise of decorative prelaminated and balancing 9mm MDF . Each Panel consists of 2Nos Intermediate blocks.Each Panel consists of top tiles/split tiles. These tiles shall slide in to the panels from top before fixing the top horizontal.In case of split tiles, it shall in Fabric magnetic tiles, Whiteboard tiles. Each Panel consists a bottom tile. These bottom tiles shall be slide fitted on to the assembly frame of the panel .All partitions and side panels have leveling screws for adjustment in case of Uneven floor to take care of +/- 25 mm of uneven flooring. Split Tile Finishes : Fabric Magnetic Tiles: Fabric magnetic tiles shall be fabric upholstered metal tiles in 0.6 mm thick G.I. Grade O as per IS: 277. The fabrics shall be upholstered with adhesives. • Fabric slide Tiles: Fabric tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with P.E. foam in the tile for tackablity. The fabric shall be upholstered with adhesives. • White Board Tiles : White board tiles shall be made of 9.0 mm thick pre laminated MDF having all its edges with minimum 0.5 mm thick PVC edging. Aluminium Trims : The top trims and end trims shall be made from aluminum extrusion. All kinds of extrusions shall have average wall thickness of 1.2 mm with powder coat finish Top trim shall be press fitted on the horizontal extrusion, it shall be slide fitted with the help of top trim connector made from PP copolymer 3530 grade. End trim shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513/ Aluminum powder coate. Wire Management - Wires shall be taken into the system through cable ducts /one raceway from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Wires runs through the system from Bottom tile and extended to the top at various locations . Work surface : Worktop and counter worktop (200mm depth ) shall be made out of 25mm thick prelaminated Exterior Grade MDF board. All the open edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. Work surfaces are fitted to the panels by work surface brackets. Brackets are made of 2.0mm thick CRCA grade D steel as per IS : 513. Brackets are slide in between end trim and vertical extrusions. Mobile Drawer : Mobile Drawer Unit shall have 3 Drawers Unit with flat metal front and top with Central locking. The Drawer Unit consistes of 2Box and 1File Drawers. The Overall minimum size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction & Material of Drawer Unit : 18 mm thick prelamianted MDF board with 2mm thick PVC edge bending /Welded Assembled of 0.8 thick CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear Side Stiffener & Bottom, ,Top Stiffener & Bottom stiffener1.2 thick CRCA powder coating. All Drawers with Double extension /telescopic precision ball slide shall be provided. For Drawer pulling, handle /side wise tapered recess provided in shell behind Drawer Fronts. Locking:10 lever Cam Lock & Central Right Hand locking with actuator & lock channel mechanism. Castors : Swiveling 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the minimum thickness of 50 microns. Key Board Pullout Tray : Supplying and Fixing of sliding computer key board tray of 480mm (L) X 280mm (D) X 40mm(H) made out of CRCA steel as per IS : 513 made of 0.9mm thick powder coated with sliding channels and other fixing fittings. It should also have a sliding system for accommodating mouse. CPU Trolley : Supplying and Fixing of CPU Trolley of Size - 345mm(W) x 226(D) x 180mm(H) is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. It consists of 4Nos Non-lockable twin wheel castors made of injection moulded in Black Nylon. Interaction desk : 1500 W1 x 1500 W2

Almirah : Providing and Placing in position Plain Almirah. Overall minimum size of the almirah shall be 916 mm (W) x 486 mm (D) x 1980 mm (H) with welded construction. It should have the shelf thickness of 0.8 mm, Back thickness of 0.8mm, Door thickness of 1.0mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The almirah shall have a handle and three way locking mechanism with shooting bolts. It shall have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load minimum Capacity of 40 Kg. It shall have 4 no.s full shelves. A4 size box file(85 W x 285 D x 345 H mm) can be stored vertically on three shelves and the clear space above fourth shelf is 240mm. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of minimum 50 microns .There shall be 5 loading levels.

Double sided Racks: Providing and Placing in position Storage Racks. Overall size of the rack shall be 925 mm (W) x 590 mm (D) x 1890 mm (H). Rigid welded construction. Back panel up to the bottom of third rack shall have additional rigidity. Racks, Back panel & Skirting shall be made of CRCA 0.8 mm thickness . Side panels shall be made of 25 mm thick plywood with 0.8 mm laminate on both sides. There shall be Bottom plus four fixed racks .Each rack shall be provided with stiffener at bottom for strength. Uniformly distributed load capacity per each full shelf shall be 80 Kg minimum. Rear side of the racks shall have back stiffeners to support books on the rear side. Label Holder on each main unit to insert labels for identification. Finish shall be Epoxy polyester powder coated to the thickness of minimum 50 microns.

Single Sided Racks: Providing and Placing in position Single Sided Racks. Overall size of the racks shall be 925 mm (W) x 300 mm (D) x 1890 mm (H). Rigid welded construction. Back panel up to the bottom of third rack shall have additional rigidity. Racks, Back panel & Skirting shall be made of CRCA 0.8 mm thickness. Side panels shall be 25 mm thick plywood board with 0.8 mm laminate on both sides. There shall be Bottom plus four fixed racks .Each rack shall be provided with stiffener at bottom for strength. Uniformly distributed load capacity per each full shelf shall be 80 Kg minimum. Rear side of the racks shall have back stiffeners to support books on the rear side. Label Holder on each main unit to insert labels for identification. Finish shall be Epoxy polyester powder coated to the thickness of minimum 50 microns

2 DOOR BOOKCASE: - Providing and Placing in position 2 Door Bookcase. Overall size of the bookcase shall be minimum 920 mm (W) x 320 mm (D) x 940 mm (H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid welded Construction. The Top Panel, Back Panel , Side Panel and other components shall be made from 1.0mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision which shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of minimum 40 Kg. The 2 Door Book Case shall have 19 mm plywood Top straight edge with 1mm laminate and with 2mm PVC lipping. The finishing shall include Epoxy powder coated to the minimum thickness of 50 microns .

4 DOOR BOOKCASE: - Providing and Placing in position 2 Door Bookcase. Overall size of the bookcase shall be minimum 920 mm (W) x 320 mm (D) x 1800 mm (H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid welded Construction. The Top Pannel, Back Pannel , Side Pannel and other components shall be made from 1.0mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision which shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of minimum 40 Kg. The finishing shall include Epoxy powder coated to the minimum thickness of 50 microns .

STORAGE UNIT :- Providing and Placing in position Storage Unit for Classroom. Overall size of the storage unit shall be 450 mm (W) x 500 mm (D) x 2025 mm (H) with leveler. The construction shall be aesthetically appealing and Rigid welded construction with 1mm CRCA sheet. Legs shall be fitted with screw type leveler. The shelving shall be height wise adjustable shelf mounting, each full shelf shall have a load capacity of 40 kg UDL minimum and 4 nos. of full adjustable shelves. Storage shall be on all five loading levels. Finish shall be epoxy powder coated to the minimum thickness of 50 micron

4 DOOR PERSONAL LOCKER UNIT: - Providing and Placing in position 6 Door Personal Locker Unit. Overall size shall be 380 mm (W) x 450 mm (D) x 1830 mm (H). Locking shall have 10 Lever cam lock with lock lever plus option of hasp arrangement. Material shall be CRCA 1.0 mm thickness. Construction shall be Rigid welded construction , shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg minimum . Finish shall be epoxy polyester powder coated to the thickness of minimum 50 microns . Handle/Label holder shall be Aesthetically appealing Snap fit ABS plastic handle . Ventilation shall be attractive punched pattern for ventilation.