Delhi State Industrial And Infrastructure Development Corporation Limited Tender
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Delhi State Industrial And Infrastructure Development Corporation Limited - DSIIDC Tender
Civil And Construction
Eprocure
Opening Date25 Nov 2020
Closing Date9 Dec 2020
Tender AmountRefer Documents
Costs
EMD
₹ 9,32,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2020_DSIDC_196979_1Bid Award Id
ViewTender No
06 /(H CD-02/DSIIDC/2020-2021Tender Authority
Delhi State Industrial And Infrastructure Development Corporation Limited ViewPurchaser Address
-Website
http://http://www.dsiidc.org/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)
37.65
-
593.5
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
2610.43
-
1559.75
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding.
429.52
-
104.65
Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250x10 mm
2112
-
64
Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm
1408
-
44.1
Providing and fixing ISI marked 85x42 mm oxidised M.S. pull bolt lock conforming to IS : 7534 with necessary screws bolts, nut and washers etc. complete.
1408
-
78.15
Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete. 300x16 mm
704
-
154.85
Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm
8448
-
28.6
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate
2375.07
-
362.6
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter
924
-
236.35
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.110 mm bend.
50
-
113.1
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110 mm
302
-
181.4
12 mm cement plaster of mix : 1:6 (1 cement: 6 Fine sand)
1076.48
-
160.35
Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floatingcoat of neat cement.20 mm cement plaster.
3778.7
-
313.25
Applying priming coat : 1 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
5220.86
-
34.95
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work
14951.4
-
78.4
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
143.98
-
615.15
Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.
790.16
-
298.3
Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.
605.82
-
120.55
Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White
432
-
831.5
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia
704
-
75.6
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall. 15 mm dia nominal bore
3766.4
-
186.4
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall. 25 mm dia nominal bore
1826
-
247.85
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore
176
-
428.2
Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length15 mm nominal bore
704
-
67.8
Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality : 15 mm diameter pipe
3766.4
-
6
Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :25 mm diameter pipe
928.4
-
9.1
Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete(New work) : 15 mm nominal bore
704
-
147.75
Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete(New work) : 25 mm nominal bore
88
-
205.8
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank
220000
-
7.25
Providing and fixing PTMT bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms
2112
-
103.3
Providing and fixing PTMT bib cock of approved quality and colour. 15 mm nominal bore, 122mm long, weighing not less than 99 gms
704
-
143.95
Providing and fixing PTMT stop cock of approved quality and colour. 15 mm nominal bore, 86 mm long, weighing not less than 88 gms
704
-
103.3
Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.25 mm nominal bore, 152mm long, weighing not less than 440 gms
88
-
413.25
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
316.8
-
744.8
White washing with lime to give an even shade Old work (Two or more coats)
97577.5
-
10.25
Providing and fixing PTMT grating of approved quality and colour Circular type : 100 mm nominal dia
704
-
32.75
Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)
4521
-
84.2
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete Single rubber stopper
1408
-
27.55
Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (One or more coat applied @ 0.90 ltr/10 sqm).
18703.63
-
45.35
12 mm cement plaster finished with a floating coat of neat cement of mix : 1:4 (1 cement: 4 fine sand)
1271.89
-
214.2
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In Cement Mortar.
11.46
-
842.75
Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
7122.54
-
22.4
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
117.34
-
997.05
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
272
-
3494.2
Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.
644.69
-
615.7
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.
23749.88
-
7.2
Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality H D - 20 Cicular shape 560mm internal diameter
15
-
1300.95
Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)
127.75
-
255
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
1228.06
-
85.95
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
18
-
1158.1
Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. Internal work - Exposed on wall 20 mm dia nominal bore
4554.88
-
224.15
Painting G.I. pipes and fittings with two coats of anti-corrosiv ebitumastic paint of approved quality 20 mm diameter pipe
4554.88
-
7.1
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil
1505.41
-
125.95
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
1003.6
-
125.75
12 mm cement plaster finished with a floating coat of neat cemen tof mix : 1:3 (1 cement: 3 fine sand)
6831.44
-
226.8
18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).
399.19
-
255.55
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm dia. R.C.C. pipe
176
-
356.7
Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps :150 mm diameter
176
-
40.15
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size).
31.32
-
4209.05
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :"1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).
35.09
-
5481.95
Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg
88
-
279.6
12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)
284.38
-
172.95
Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete
19512.22
-
8.35
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
2323.2
-
58.45
Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge.
272
-
55.45
Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)
1052.8
-
70.45
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.M.S. tube
2408.84
-
92
Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing with cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.50 mm thick
25
-
814.55
Finishing walls with water proofing cement paint of required shade :Old work (one or more coats @ 2.20 kg/10 sqm) complete
5965.1
-
37.9
15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand)
693.76
-
185.2
Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete.300 mm weighing not less than 200 gms
4224
-
30.95
Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :4.0 mm thick glass panes
2238.72
-
689.05
Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick
1951.6
-
52.5
Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil
462.15
-
51.75
Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 19.13.1 2.30 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete.(Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :19.13.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
20
-
35380.05
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
160
-
327.9
15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)
253.8
-
209.65
Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
4
-
15028.55
Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete
37.05
-
5503.8
Dismantling manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge :bituminous road
122.5
-
177
24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanized M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).
517.5
-
1800.45
Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size,complete as per manufacturer’s specification and direction of Engineerin-Charge.
250
-
438.75
Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee with door 110x110x110 mm
150
-
181.55
Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee without door 110x110x110 mm
150
-
167.6
Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :20 mm nominal bore
352
-
170.95
Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :For pipes 350 to 450 mm diameter
1
-
674.15
Providing and fixing in concrete box precast RCC railing/grill M-30 grade of size 1000*1000*50mm complete as per direction of Engineer in charge.
154
-
1220
Providing and fixing in position precast RCC cover Manhole of required shape and approved quality complete as per direction of Engineer in charge. Rectangular shape 700X550 mm
190
-
685.28
Cleaning of DU's i.e removal of mortar, sweeping cleaning of wall tiles, including wc & bathroom as per direction of Engineer in charge
704
-
851.15
P/F 3mm transulent acrylic plastic sheet with all necessary screws complete as per specification and direction of E-In-C.
81.38
-
696.9
Providing and fixing in position pre-cast R.C.C. manhole cover of required shape and approved quality H D - 20 Circular shape 560 mm internal diameter
15
-
1103.42
Providing & fixing GI extension connector (Tank nipple) for water tank pipe, fittings of approved quality & colour. 25mm
264
-
97.31
Providing and fixing kitchen sink of size 650x450x200mm with 18 mm thick marble complete as per specification and direction of E-in-C.
704
-
1027.93
Removal of cemant mortar/ concrete article from terrece i/c Cleaning & disposal of unservicable material within 50 Mtr. lead as per direction of E-in-C
5398.14
-
15.33
P/F PVC waste jalli and rubber plug complete for sink or wash basin :- 32 mm dia
704
-
62.65
Providing cement based water proffing compound for teratment of roof, complete as per sepecifiacation and direction iof E-in-C
574.33
-
58.08
Cleaning of SW drain including removing the existing RCC covers, clearning drain including draining out of mud, foul sludge and keeping all safety precautions of snake bite inclusive stacking of material with a lead of 50 mtr and refixing covers complete as per direction of Engineer-in-Charge
2148.8
-
69.69
Supply and placing precast RCC perforated drain cover of required shape & approved quality in rectangular shape, complete as per spcefication and direction of Engineer-in-charge
82.5
-
1277.65
Providing and laying HDPE pipe of material grade PE-80, PN-4 as confirm to IS-14333-1966 (ammended upto date) including butt fusion jointing complete as per direction of Engineer in charge. 500 mm OD
255
-
5549.99
Rewiring for light point/ fan point/ exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable and 1.5 sq.mm. FR PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel conduit including dismantling as required Group A
7920
-
290
Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 3 x 1.5 sq. mm
31680
-
50
Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.3 x 4 sq. mm
5632
-
111
Supplying and drawing following sizes of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.3 x 6 sq. mm
10032
-
162
Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required 20mm
1408
-
126
Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required 32mm
704
-
198
Supplying and fixing following piano type switch/socket on the existing switch box/ cover including connections etc. as required. 5/6 amps switch
9152
-
34
Supplying and fixing following piano type switch/socket on the existing switch box/ cover including connections etc. as required.2 way 5/6 amps switch
176
-
39
Supplying and fixing following piano type switch/socket on the existing switch box/ cover including connections etc. as required.15/16 amp switch
704
-
75
Supplying and fixing following piano type switch/socket on the existing switch box/ cover including connections etc. as required.3 pin 5/6 amp socket outlet
1408
-
42
Supplying and fixing following piano type switch/socket on the existing switch box/ cover including connections etc. as required.6 pin 15/16 amp socket outlet
704
-
86
Supplying and fixing following piano type switch/socket on the existing switch box/ cover including connections etc. as required.Bell push
704
-
47
Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc as required.
4224
-
46
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole
2816
-
173
Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps
1408
-
222
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
88
-
3672
Supplying and laying 25 mm X 5 mm G.I strip at 0.50metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
660
-
85
Supplying & Fixing brass batten/angle holder including connection etc. as required at site.
3520
-
75
Supply, Erection, Installation, Commissioning and testing of cubical type Double Pole Isolator Housing panel fabricated with 1.6mm thick CRCA sheet suitable to accommodate Double pole Isolator for each quarter suitable size with 2mm thick acrylic sheet cover, with depth 15 cms, neutral link with kitkat, busbar chamber, With locking arrangements etc with interconnections complete as required at site(for 16 Nos DP isolator & 1 staircase DP Isolator)
44
-
17227
Supply & Fixing of MS Sheet encloser cover of existing DB(2+4 way) with screws etc as complete reqd at site
704
-
250
Supply & Fixing of following Sizes phenolic sheets onexisting box including cutting of sheet for fixing surface and sockets with screws & Washers etc completed as required at site 4"x4"
2112
-
25
Supply & Fixing of following Sizes phenolic sheets onexisting box including cutting of sheet for fixing surface and sockets with screws & Washers etc completed as required at site8"x6"
2112
-
75
Supplying, installation, testing and commissioning of submersible unclog pump with MS stand with lifting hook of Darling/Kishore/ equillant make with following specification HP/KW:20/15 Head : 15 Mtrs. Discharge :3135 LPM Delivery outlet :150 MM Maximum Solid handing :100 mm Method of starting star delta RPM 1460 size of cable 2x3x4 sq. mm
2
-
318000
Supplying and fixing of following sizes of 'B' class of MS pipe screwed double flanged pipe i/c making holes in the wall making good the same using cement concrete and water proofing compound, nuts, bolts washers, rubber insertion brick masonry supports painting and testing etc. as requried. b) 150 mm NB
30
-
1900
Supplying and fixing following sizes of double flanges non rising spindle type C.I. sluice valves i/c nuts bolts washers rubber insertion hand wheel, painting and testing etc. as required. a) 150 mm NB
2
-
34050
Supplying & fixing of following size of double flanges C.I. non return valve without bye-pass arrangement i/c nuts, bolts, washers rubber, insertion painting and tesing etc. as required .a) 150 mm dia
2
-
25000
S/F C.I. double flanged 90 degree bend complete with nut and bolts washers, rubber, insertions, painting and testing etc. as required. a) 150 mm dia.
4
-
3100
S/F of following sizes of M.S. all site flanged tees i/c nut, bolts, washers, rubber insertions and testing etc. as required of size 150 x 150 mm
2
-
4275
P/F MS heavy duty holding clamps suitable for above pump set.
4
-
2425
S/L of 2 x 3 x 4 sq. mm flat submersible heavy duty cable suitable for above pump set Finolexe/Angle/Kalinga make.
50
-
1500
S/I/T/C of indoor type starter cum control panel containing of ammeter, volt meter, starter switch, phase containing lamps, single phase preventer, dry run, over load & under load protection, moisture sensor enclosed in a sheet metal box with.
2
-
65000
Earthing with G.I. earth pipe 4.5 mtr. Long and 40 mm dia i/c accessoriea and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc with charcoal and salt as required.
2
-
3672
Supply and erection of 07 mtr.Octagonal Pole HLOPL-7M TOP: 70 MM Bottom : 130 mm Plate thickness 3, base plate 200 x 200 x 12 a) Foundation Bolts : J Type b) Single Bracket 0.5Mtr for Pole having top 70 mm A/F c) C/o Shallow foundation with M-20 Grade concrete for the pole considering the safe soul bearing capacity at site
50
-
18230
Supply & Fixing of Highly efficient following LED Street Light with lens made of pressure dia cast aluminium housing & enclosed with toughened glass IP66 90 watt LED
50
-
9589
Supply & Fixing of Highly efficient following LED Street Light with lens made of pressure dia cast aluminium housing & enclosed with toughened glass IP66 120 Watt LED
32
-
11477
Supplying & fixing of GI pipe of 40mm dia (nominal), 3 metre length along the pole for protection of under ground cable etc. as reqd.
50
-
1217
Supplying and drawing of 2 X 2.5 + 1 X 2.5 sq.mm.in exsting pole for of wiring light fitting complete as reqd.
540
-
206
Supplying of XLPE insulated, PVC sheathed 1.1 KV grade aluminium conductor armoured cable as per IS : 7098 of size :(Make Grandlay or equivalent.) 4 x 35 sq.mm.
100
-
221
Supplying of XLPE insulated, PVC sheathed 1.1 KV grade aluminium conductor armoured cable as per IS : 7098 of size :(Make Grandlay or equivalent.) 4 x 16 sq.mm.
1250
-
132
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1. KV grade as required :4 x 35 sq.mm.
4
-
283
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1. KV grade as required :4 x 16 sq.mm.
136
-
255
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.Up to 35 sq.mm
1350
-
18
S/I/T/C of 9 meter long semi high mast octagonal galavanized pole with welded base plate (400 x 400 x 20) with intigrated connector box inside the pole containing one number 32 amp DP MCB (10 KA), neturaol linka and earth terminal and one no. additional connector box on the ring at the top of the pole for terminating the wires coming from fittings including transportating handling, RCC foundation having opening two cables, foundation bolts and with ciruclar ring of suitable dia made of 50 mm dia GI pipe for mounting the fittings etc. complete as required.
8
-
40000
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.. Direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand suchioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)
1350
-
135
INCOMING :Supplying, installing, testing & commissioning of weather proof feeder pillar, metal clad, suitable for 415 Volt, 3 Phase, 50 Hz with suitable foundation and arrangement for incoming / outgoing cabling / cable termination, earthing, locking arrangment, insulated aluminium Bus-Bar system, interconnection etc. ( As per fig. 2 of CPWD Electrical Spectification) with provision of phae indicating lamps, volmeter / ammeter with selector switch on the incoming side. (a) 160 A TPN MCCB, 25 KA BC 1 no. (b) 63A TPN MCCB 25 KABC 6 nos.
2
-
60000
EARTHING & PROTECTION LUMINARE: Earthing with G.I. earth pipe 4.5m long , 40 mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.With charcoal and salt as reqd.
32
-
2846
Providing & fixing 6 SWG dia.GI wire on surface or in recess for loop earthing along with existing surface/recessed conduit/submain wiring/cable as required.
2700
-
23
Supplying, installlation testing and commissioning of electrical driven horizontal split casing centrifugal pump set with Bronze impeller capable to perform the following duties, directly coupled to suitable rating of 3 phase 50 Hz A.C. supply, 400/440V, 2900 RPM (nominal) TEFC squirrel cage induction motor with suitable type of tyre type coupling with coupling guard mounted on a common M.S. channel base plate with cement concrete foundation of CC. Mix 1:2:4 ( 1 cement, 2 coarse sand 4 stone aggregate) of suitable size, including foundation bolts, nuts washers, anti vibration pads alignment and numbering complete etc. as required. (Suction pipe 80 mm dia, Delivery pipe 65 mm dia). a) Discharge :- 72 LPS b) Head :- 50 Mtr. c) Type of liquid to be pumped :- Clear water d) Min H.P. of motor :- 25 H.P.
2
-
185000
Supplying installation, testng and commissioning of dewatering pump set suitable to deliver 420 LPM at a head of 7.5 mtr. Single phase, 2008220V, 50Hz, A.C. supply i/c panel board with accessories and cable etc complete as required.
1
-
40000
Supplying and fixing of following sizes of 'B' class C.I. screwed double flanged pipe i/c making holes in the wall making food the same using cement concrete and water proofing compound, buts, bolts washers, rubber insertion brick masonry supports painting and testing etc. as requried. b) 100 mm NB
10
-
2250
Supplying and fixing C.I./M.S. flanged fittings of following sizes complete with nuts, bolts, washers, rubber insertions painting and testing etc. required. a) 100 X 100 X 100 mm all flanged tee.
1
-
2750
Supplying and fixing C.I./M.S. flanged fitting of following sizes complete with nuts, bolts, washers, rubber insertions painting and testing etc. requried. b) 100 mm dia 90 bend.
4
-
1500
Supplying and fixing C.I./M.S. flanged fittings of following sizes complete with nuts, bolts, washers, rubber insertions painting and testing etc. required. d) 100 mm dia 90 duck foot bend.
2
-
2500
Supplying and fixing following sizes of double flanges non rising spindle type C.I. sluice valves i/c nuts bolts washers rubber insertion hand wheel, painting and testing etc. as required. a) 100 mm NB
3
-
12500
Supplying & fixing of following size of double flanges C.I. non return valve without bye-pass arrangement i/c nuts, bolts, washers rubber, insertion painting and tesing etc. as required .a) 100 mm dia
2
-
11000
Supplying & fixing water pressure gauge 150mm dia (O to 7 kg./cm2) mounted on frame made of angle iron 30mm X 30 mm X 5mm, on dia copper tubing from pump to pressure gauge & nipple etc. i/c connection, testing etc. as required.
2
-
1000
Supplying & fixing following size of G.I. pipe 'B' class i/c all fittings of elbows. Sockets. Tee, union, cutting/sizing, threading painting with silver paint etc. complete as required. 50 mm dia
40
-
888
Supplying & fixing following size of G.I. pipe 'B' class i/c all fittings of elbows. Sockets. Tee, union, cutting/sizing, threading painting with silver paint etc. complete as required.100 mm dia
6
-
3125
Supplying & fixing of 3 Nos. Fire buckets each of 9 ltrs. Capacity mounted on suitable MS stand made of angle iron of size 35mm X 35mm X 6mm thick duly painted i/c filling of buckets with jamuna sand etc. as required.
1
-
1000
Supplying and laying checkered/corrugated red/black rubber mat sheet (ISI marked) suitable for 1.1 KV grade for size 2000mm X 1000mm X 6mm thick as required.
1
-
1000
Supply & fixing shock treatment chart in Hidi & English language duly framed in glass and wooden fram as required.
2
-
250
Supplying & fixing of ISI marked (IS 2878) carbon dioxide type fire exhnguisher fully charged 4.5 kg. Capacity complete with bakelite horn, discharge tube & GI bracket for wall mountas required.
2
-
4000
S/I/T/C of 3 Phase Star Delta Panel 30 HP Booster Pump including indicator, cable with all accessories as requried at site.
1
-
22500
Supplying XLPE inslulated PVC wsheathed 1.1 KV grade aluminum conductor armoured cable as per IS:7098 of size (poly cab or equivalent make) etc as required a) 4 x 35 sq.mm (incorner cable to panel from energy meter)
40
-
221
Supplying XLPE inslulated PVC wsheathed 1.1 KV grade aluminum conductor armoured cable as per IS:7098 of size (poly cab or equivalent make) etc as required a) 4 x 16 sq.mm (incorner cable to panel from energy meter)
35
-
132
Supply and installing following sizes of perforated M.S. cable trays including horizontal & vertical bends reducers, tees, cross members and others accessories as required and duly suspended from the ceiling eith M.S. suspenders and including painting etc. as required. (a) 100 mm width X 50 mm depth X 1.60mm thickness.
15
-
348
Supplying and making and termination with brass compression gland and aluminum lugs for following sizes of PVC insulated and PVC sheathed aluminuim conductro cable of 1.1 KV grade as required. (a) 3.5 X 35 sq. mm
2
-
282
Supplying and making and termination with brass compression gland and aluminum lugs for following sizes of PVC insulated and PVC sheathed aluminum condutor cable of 1.1 KV grade as required. (b) 3.5 X 25 sq. mm
4
-
257
Earthing with G.I. earth pipe 4.5 mtr. Long and 40 mm dia i/c accessoriea and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc with charcoal and salt as required.
2
-
3672
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
30
-
129
Laying of one numerb of PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of following size in the existing RCC/HUME/METAL/pipe as required upto 35 sq. mm
75
-
18
Add - 15.69% on DSR items (Civil)
1
-
4259988.26
Add - 12.75% on DSR items (Electrical)
1
-
1173403.41
Less - 9.5% on DSR items
1
-
3969815.58
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements