Delhi State Industrial And Infrastructure Development Corporation Limited Tender

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): Flush / Ruled/ Struck or weathered pointing

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Distempering with 1st quality acrylic distemper (ready mixed) having VOC Low content less than 50gramm/litre of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification. New work (Two or more coats) over and including water thinnable priming coat with cement primer having loc VOC content less than 50gm/ltr

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge. 75mm average thickness

Designing, providing, installing and fixing factory finished custom designed cold form Light Gauge Steel Framed super structure comprising of steel wall panel, trusses, purlins etc manufactured out of minimum 0.75 mm thick steel sheet as per design requirements. The steel sheet shall be galvanized (AZ-150 gms Aluminium Zinc Alloy coated steel having minimum yield strength 300- 550 Mpa) conforming to AISI specifications and IBC 2009 for cold formed steel framing and construction and also as per IS: 8751987, ISO 800-1984 and IS: 801- 1975. The wind load shall be as per provisions of IS 875 (part -III). LGSFS frame shall be designed as per IS: 801 using commercially available software such as Frame CAD Pro-11.7/ STAAD PRO-V8i/ArchitekV2.5.16/ Revit architecture2011 or equivalent. Proper usage of Connection Accessories like Heavy Duty Tension Ties, Light Duty Hold-ons, Twist Straps (to connect truss with wall frames), Strong Tie, Tie Rod, H-Brackets, Boxing Sections, L-Shaped Angles for better structural stability. The framing section shall be cold form C-type having minimum web depth 89 mm x 39mm flange x 11mm lip in required length as per structural design requirement duly punched with dimple/slot at required locations as per approved drawings. The slots will be along centre line of webs and shall be spaced minimum 250mm away from both ends of the member. The frame can be supplied in panelized or knock down condition in specific dimensions and fastened with screws extending through the steel beyond by minimum of three exposed threads. All self drilling tapping screws for joining the members shall have a Type II coating in accordance with ASTM B633(13) or equivalent corrosion protection of gauge 10 & 12, TPI 16 & 8 of length 20mm. The frames shall be fixed to RCC slab or Tie beam over Neoprene rubber using self expanding carbon steel anchor bolt of dia as per approved drawings. design subject to minimum 12mm diameter and 121mm length conforming to AISI 304 and 316 at 500mm c/c with minimum embedment of 100mm in RCC (RCC to be paid separately) and located not more than 300mm from corners or termination of bottom tracks complete in all respects. The item also includes the submission of stability reports duly examined and issued by any NIT/IIT.The rate includes the concept design, detailed design, fabrication of sections, transportation, installation and all required fixing arrangement at site as described above.

Providing and fixing 12mm thick ASBESTOS fiber sheet ISI marked IS : 13990, plain lining both side of M.S. Pipe Frame with Necessary screws, priming coat on unexposed surface etc., complete. As per direction of Engineer-in-charge (cost of frame work to be paid for separately).

Charges of disposal C&D waste at approved dumping ground (which will be reimbursed to the contractor on receipt of original invoice).

Providing and Fixing Stainless Steel Letters of 316 SS Grade of Thickness 18 Guage Fixing with Necessary SS Screw etc Complete and Sample approved by Engineer Incharge Size =300 mm "NAME PLATES"

Providing and fixing of Electric fire safety led signage of acrylic sheet and Fixing with Nescessary SS Screw/chain etc Complete and Sample approved by Engineer Incharge size= 12'' x 6'' in 8 mm "RADIUM SIGNAGE FOR FIRE SAFETY"

Providing and fixing warning sign of ACP sheet digitally printed 3M radium vinyl (No smoking, fire exit, stairs, No horn, and use dust bin.) with Necessary SS Screw/chain etc Complete and Sample approved by Engineer Incharge . Size: 12 x 6 inch with3mm thick

Providing CO2 High Pressure trolley mounted 9 kg Fire Extinguisher, filled with Co2 Gas as per IS 15222, Gross Weight 36 Kg, empty weight 27 Kg, Control discharge mechanism fitted with 2 Meter Wire Braided Hose & Flat Horn with Diffuser Nozzle for dispersed discharge of CO2, Discharge Time 30 Sec, Average Discharge is 95%, applicable on Class B, C and electrically started Fire, Internal coating is not applicable & External coating is of enamel spray painting, Valve Confirm to IS 3224 ISI Marked, CO2 Cylinder construction: hot spinning by seamless pipes & bearing ISI mark, Body confirms to IS 7285 and PESO APPROVED, Extinguishers confirmed to IS 16018 2012 and ISI marked Fire Rating: 55B

Add 31.27% enhancement on DSR

Less 9.5% enhancement on DSR