Delhi State Cancer Institute Tender

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns, etc. for mass concrete

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand): 25 mm thick

Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steelprimer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. Granite of any colour and shade

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand)

Supply and installation of fully insulated wooden fire door of 120min. fire rating, of maximum 52mm thickness, comprising of 75mm x 44mm hardwood internal timber frame work, with infill insulation of 20mm thick of of 48 kg/m3, wool insulation, coated with viper intumuscent coating on both sides for insulation. The coated insulation shall be sandwiched between min 12mm thick Non Combustible (Calcium Silicate) Boards on both sides (edge to edge on internal Hardwood frame) and cladded with 3mm Thick Commercial Ply & 1mm Thick Laminate (Any Regular Plain Shade In Suede Finish) on both faces, with 52mm x 10mm exposed hard wood lipping all round the shutter the main door frame will be made out of Hard Wood (Red Mirandi) of section 120 x 70mm and coated with viper Fire retardent Primer. The rebate shall be of 20mm x 55 mm in Door Frame to accommodate the shutter in frame.The frame shall be fitted with fire & smoke intumescent seal of size 20 x 4mm on frame & shutter . The cost of frame and necessary stainless steel hinges with srewss is included)The pasting of the ply / laminate should be done using automatic machine and should be free from any nails or perforations. The manufacturer should be compliant to ISO 9001: 2008 and CE certified, manufacturer should be covered under IGBC scheme. Approved manufacturer Navair International Ltd or Hormann or equivalent as approved by Engineer -In-Charge and should be ISO Certified company.The board shall be Resistant to vermin, mould growth, minor impact, abrasion and short term water attack and shall be Off –white in colour with a smooth surface suitable to receive most forms of decoration having following technical characters i.e.; The Construction design similar to NWD12050 and similar to the design tested as per BS 476 part 22 and IS 3614 Part II, at CBRI, India. The shutter can be provided with appropriate openings for view panel glass. Prototype Test certificate for fire rating of doors from CBRI, Roorkee for earlier tested design shall be attached along with manufacturers test certificate. as per approved architectural drawings and complete as per the directions of Engineer-In-charge.

Providing and Fixing 8 mm thick multiwall polycarbonate sheet UV resistant (Translite make , Lexan or Equivalent ) of desired colours as approved by Engineer-in-charge upto 10m height. mounted and fixed with screw and fastners and finished with sides filled with silicon on existing frame for proper finishing including anodised aluminium trapeziodal profile set 60mm wide including top and bottom profile with rubber gasket of required size and patteren over SS frame including necessary screws & fastner as per direction of Engineer-incharge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)(bricks provided by department at site)