Delhi Jal Board Tender

S/O MS pipe conforming to IS: 3589 of class ‘B’, 100mm diameter. Make: Jindal / Tata

S/O Gun metal Gate valve of 40 mm diameter. Make: Sant / ISI Marked

S/O Galvanized pipe 40 mm diameter heavy duty “B” class. Make:- Jindal/Tata

S/O MS Bend of size: 100 mm dia. (90⁰), Heavy Duty.

S/O MS flange of 100 mm dia. 19 mm thickness.

S/O Nut bolt with washers of good quality (off size), as per site requirement.

S/O Rubber insertion jointing sheet. Make:-Jyoti / National.

PVC insulated (heavy duty) single-core un armoured copper conductor cables for working voltage up-to and including 1100 volts of 10 cross section. Make: Grandlay/ Gloster/ HAVELLS.

PVC insulated (heavy duty) single-core un armoured copper conductor cables for working voltage up-to and including 1100 volts of 25 cross section. Make: Grandlay / Gloster / HAVELLS.

Supply & Installation of LT Distribution panel sheet steel enclosure made out of 2mm CRCA sheet totally enclosed, powder coated free standing, floor mounted type, dust& vermin proof, outward opening, lockable doors having hidden hinges and a bolted back cover both using non-deteriorating neoprene rubber gaskets to provide IP protection .The each part of the fabricated panel will be strictly subjected to seven tank treatment. The various components, assemblies and sub equipments of the panel will be as per standard given in relevant IS. The bus bar of the panel will be shaped out of high conductivity, electrolytic conductor and shall be liberal sized in aluminum. The control wiring of the panel will be done with PVC flexible copper wires of 1.5mm cross section. Each wire will be terminating with a ferule crimped to the wire, size 1200MM X 1000MM X 400MM. Having following components make. MCCB 415V, TP 3phase 50Hz, 100Amp with handle & Spreader: - 1 No. Make L&T/Siemens MCCB 415V, TP 3phase 50Hz, 50Amp:- 2 No. Make L&T MCB Single pole 6Amp:- 9 Nos. Make L&T/Havells MCB Triple pole 32Amp:- 2 Nos. Make L&T/Havells Power capacitors 415V unit of 8Kvar:- 2 Nos. Make: Epcos Over load relay 20-33:- 2 Nos. Make: L&T/siemens Over load relay 4.5Amp. -7.5Amp:- 1 No. Make: L&T/siemens Digital Amp. Meter: - 4 Nos. Make AE/L&T Digital Volt Meter0-500V:- 1 No. Make AE/L&T Motor protection Relay: - 2 Nos. Make: L&T/Siemens Power contactor 220V 3phase50Amp:- 4 Nos. Make L&T / siemens Power contactor 220V 3phase32Amp:- 2 Nos. Make L&T / siemens Power contactor 220V 3phase18Amp:- 1 No. Make L&T / siemens Star delta timer on delay: - 2 No. Make: L&T/Siemens Indicating lights LED type RYB & On/OFF: - 9 Nos. Make : L&T / Havells Current Transformer200/5, 50/5:- 12 Nos. Make AE / Advance On load change over switch 200Anp. Open execution type: - 1 No. Make: L&T Fitting of the above components in panel enclosure with terminal blocks, channels, ferrules, thimble, support insulator on bus bar, required hardware complete in all respect. Loading, unloading by crane or heavy labor and cartage up to site. Dismantling of old panel structure including removing of cable etc. from site, cleaning & dressing the surface for Installation of the panel at site on base frame, laying of cable, termination of cable both incoming & out going side. Testing & commissioning of panel & allied accessories as per required parameters with relevant IS .testing of the panel prior to switching on as follow:- (i) Continuity and earth testing. (ii) Meggaring of all equipments for phase to phase, neutral to body, neutral to earth and phase to earth.

Providing of 45 watt LED, street light fitting pressure die cast AL. housing with heat resistant toughened glass & IP 65 Protection, complete with all accessories. Make: Havells/Bajaj/ Crompton.

Providing of 72 watt LED, street light fitting pressure die cast AL. housing with heat resistant toughened glass & IP 65 Protection, complete with all accessories. Make: Havells/Bajaj/ Crompton.

Wiring for circuit /sub-main wiring along with earth wire with the following sizes of FR PVC insulated copper conductor. Single core cable in surface / recessed PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire. (DSR 1.14.3)

Dismantling of two 20 hp p/sets by cutting of horizontal suction line with gas cutter inside the underground reservoir and dismantling the foot valve. Dismantling of existing suction and delivery line outside the reservoir by cutting the nut bolts with help of gas cutter. Dismantling the existing pump and motor, by cutting of nut bolts from base frame, de-coupling the pump & motor and disconnecting the electric connections of motor. Fixing new P/set on base frame. Any civil work requirements needed for fixing of pump/set on base frame grouted in foundation. Making connections, Installing foot valve, Non-return valve, sluice valve, reducer & fixing of flanges, welding of joints, tightening of nut bolts etc. with new pipe in suction and delivery system, all tools & tackles, loading & unloading i/c safety equipment & other precautions, testing & commissioning. The job to be done on turn-key basis and any item not mentioned above but required to complete the work will be provided by the contractor.