Delhi Development Authority Tender

Providing and fixing Air Walker with below specifications: Dimensions (LxWxH): 1100x550x1480mm, fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. ‘U’ shaped main frame of NB 65mm (G.I) ‘C’ Class Pipe. All other pipes of NB 32mm (G.I) ‘C’ Class. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres), all pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of nylon alloy with rounded edges to prevent impact and injury. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless-steel label fixed on equipment for ease of use. including maintenance cost for 2 years

Providing and fixing Horse Rider Station with below specifications: Dimensions (LxWxH): 1000x600x1100mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 65mm (G.I) ‘C’ Class pipe. Handle support frame of NB 50mm (G.I) ‘C’ Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I) ‘C’ Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. including maintenance cost for 2 years.

Providing and fixing Leg Press in a pair with below specifications: Dimensions (LxWxH): 1750x550x1600mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 50mm (G.I) ‘C’ Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 50mm (G.I) ‘C’ Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and selflubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. including maintenance cost for 2 years.

Providing and fixing Pull Chair in a pair with below specifications: Dimensions (LxWxH): 1950x700x2000mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 50mm (G.I) ‘C’ Class pipe. Handle frame of NB 32mm (G.I) ‘C’ Class pipe.(‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Handle bars are provided with high end quality rubber grips. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. including maintenance cost for 2 years.

Providing and fixing Seated Chest Press in a pair with below specifications: Dimensions (LxWxH): 1800x700x2000mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 50mm (G.I) ‘C’ Class pipe. Handle frame of NB 32mm (G.I) ‘C’ Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Handle bars are provided with high end quality rubber grips. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. ) including maintenance cost for 2 years

Providing and fixing Arm Wheel in a pair with below specifications: Dimensions (LxWxH): 850x800x1800mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 32mm (G.I) ‘C’ Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. including maintenance cost for 2 years.

Providing and fixing Elliptical exerciser with below specifications: Dimensions (LxWxH): 1200x540x1600mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 65mm (G.I) ‘C’ Class pipe. Handle frame of NB 32mm and 25mm (G.I) ‘C’ Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Handle bars are provided with high end quality rubber grips. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. including maintenance cost for 2 years.

Providing and fixing Double Cross Walker with below specifications: Dimensions (LxWxH): 1600x600x1600mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Handle frame of NB 32mm and 25mm (G.I) ‘C’ Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). Foot support frame of 100x50x2.5mm CRC rectangular pipe. All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 50mm (G.I) ‘C’ Class pipe. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. including maintenance cost for 2 years.

Providing and fixing Triple Twister with below specifications: Dimensions (LxWxH): 1700x1300x1300mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 32mm (G.I) ‘C’ Class pipe. Handle frame support of NB 32mm (G.I) ‘C’ Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). Foothold plate of made of cost iron of 12mm thickness. All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment is fixed on ground with concrete of minimum strength M-25 and Expansion Bolts. Once the concrete is set, the equipment is fixed on to it. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. including maintenance cost for 2 years.

Providing and fixing Rowing Machine with below specifications: Dimensions (LxWxH): 1280x800x1150mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 65mm (G.I) ‘C’ Class pipe. Handle support frame of NB 25mm (G.I) ‘C’ Class pipe.(‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 65mm (G.I) ‘C’ Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use. including maintenance cost for 2 years.

Lifting/Disposal of unserviceable scrap such as old gym equipments from DDA parks

SCHEDULE-B Regular maintenance for three years( After free maintenance for 2 years) of all the Gym equipments (10 Nos. ) Installed in DDA parks as per schedule A consisting following :- a) Inspect and adjust of drive, timing and running belts. b) Check and set right/replacement for worn bearings, misaligned moving points, adjust/tighten loose parts, covers, seats, foundation and flooring. c) Tighten of nuts/bolts/screws i/c welding of various part/joints of equipments wherever required. d) Calibration of Instruments. e) Priming coat & painting coat, if required. f) Lubrication/ oiling. g) Replacement/repair of parts of equipment in case of Theft/ vandalism. h) Replacement of damaged parts & rectification of any others defects observed as per direction of Engineer-in-charge except : i. Due to Force majeure or ii. Abnormally bad weather, serious loss or damage by fire or iii. Damage due to act of god or iv. Any other cause which in the absolute discretion of the engineer-in-charge is beyond the contractors control . Maintenance cost (i) For 3rd year for all 10 Nos. of Gym Equipments

(ii) For 4th year for all 10 Nos. of Gym Equipments

(iii) For 5th yearfor all 10 Nos. of Gym Equipments