Delhi Development Authority Tender
... More
If you're typing tender ID over and again or finding it difficult to go through the cumbersome government websites for looking at Delhi tenders online. We have come up with a solution i.e. we have collated every eprocurement Delhi tender on BidAssist. Also, for any queries related to an e-tender Delhi, like the bidding process, registration process, etc., the same are explained below.
Delhi Development Authority - DDA Tender
Civil And Construction
Eprocure
Opening Date10 Feb 2025
Closing Date15 Feb 2025
Tender Amount₹ 2,38,79,480
Technical
Technical
Class Of Bidder
... View More
The class eligibility requirements to bid or participate in this tender are Class-I, Class-II, Class-III, Class-IV, and Class-V. Bidders must belong to one of these classes to participate.
Bid Capacity
... View More
The bid capacity required to bid for this tender can be summarized as having completed similar works with values of at least one of the following:
- Three works totaling at least Rs. 95,51,792, - Two works totaling at least Rs. 1,43,27,688, - One work of at least Rs. 1,91,03,584. These values are derived from the estimated cost of the work, using the following formulas:
1. 40% of the estimated cost: 0.4 * 2,38,79,480 = 95,51,792
2. 60% of the estimated cost: 0.6 * 2,38,79,480 = 1,43,27,688
3. 80% of the estimated cost: 0.8 * 2,38,79,480 = 1,91,03,584.
Technical Capacity
... View More
The required prior work experience for the bidder includes completing similar works with specific value and percentage requirements. The bidder must have completed one of the following:
* Three similar completed works costing not less than 40% of the estimated cost put to tender, with a value of Rs. 95,51,592/-.
* Two similar completed works of an amount equal to not less than 60% of the estimated cost put to tender, with a value of Rs. 1,43,27,688/-.
* One similar completed work equal to an amount not less than 80% of the estimated cost put to tender, with a value of Rs. 1,91,03,584/-. The similar nature of works refers to Building Works along with Internal Electrification & Installations (IEI), and the bidder should have work experience of satisfactorily completing similar nature of work under any Govt. Department, Public Sector Undertaking, Sports Authority of India, Sports Departments of State Governments, during the last 7 years. The value of executed works shall be brought to the current costing level by enhancing the actual value of work at a simple rate of 7% per annum.
Costs
EMD
₹ 4,77,590Document Cost
Refer DocumentsTender Fee
Refer Documents
Summary
Running And Maintenance Of Dda Roshnara Club For The Year 2024-25.
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_DDA_848368_1Bid Award Id
ViewTender No
22/NIT/EE/SMC/DDA/2024-25.Tender Authority
Delhi Development Authority ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-lll) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)
75
6518
488895
... More
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)
11.5
9105
104718.43
... More
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
116
1267
147082.2
... More
Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
2.5
2392
5981.63
... More
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
2569
133
343475.3
... More
Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer Using M.S. angels 40x40x6 mm for diagonal braces
7.56
5804
43880.89
... More
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes.
3560
194
692064
... More
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
35
772
27034
... More
Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand):Medium shade pigment using 50% white cement 50% Grey cement.
236
1328
313490.6
... More
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick
121
1948
235738.25
... More
40 mm thick rubbed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar. Red sand stone
450
1647
741150
... More
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
24
1330
31920
... More
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. size of Tile 600x600 mm
72
1553
111848.4
... More
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to 1S:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size 300X300
256
1455
372646.4
... More
Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to 1S: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).size of Tile 600x600 mm
5
1893
9469.5
... More
Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.
72
309
22251.6
... More
Deduct for not grouting the joints with white cement and matching pigment in the items of fixing of vitrified tiles.
72
13
-957.6
... More
Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customized design as per direction of Engineer in charge. The glass mosaic tiles shall be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operations, material and required pattern approved by Engineer-in-charge.
103
3891
400788.45
... More
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
15
3186
47800.5
... More
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 12.211 In 75x75 mm deep chase
150
305
45772.5
... More
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110mm dia
60
377
22644
... More
Supply and Installation of UV protected compact/solid Polycarbonate sheet of min. 4 mm thick with profile 50 mm complete system. Polycarbonate sheet shall be fixed with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Polcarbonate sheet will be fixed on purlin with EPDM gasket with grip lock mechanism and will be secured on MS structure with SS self drilling screws and trapezoid ss fastners holding the base of the standing seam offering best stability against wind pull out load. Polycarbonate sheet must satisfy dart drop impact test as per IS 14443-97 and shall show no sign of breakage of polycarbonate panel which have been exposed to UV for a min. of 500 hours as per ASTM G 155. Polycarbonate sheet shall be fixed over MS Structural steel/MS Purlin confirming to the detail technical specifications as per approved architectural drawings by trained and factory authorized labour with supervision to complete the entire Polycarbonate sheet installation as per the drawing and direction of the Engineer-in-charge.
63
2226
140238
... More
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
360
738
265914
... More
Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity 0.043 w/mK.
45
2158
97116.75
... More
12 mm cement plaster of mix : 1:4 (1 cement: 4 Course Sand )
434
357
155089.9
... More
Lettering with synthetic enamel paint of approved brand and manufacture all complete as per direction of engineer in charge
2400
6
14832
... More
Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour all complete to achieve even shed and colour : New work (two or more coats) over and including water thinnable proming coat with cement primer having VOC content less 50 than gram/litre.
256
185
47526.4
... More
Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)
1000
116
116900
... More
Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 90 g/10 sqm)
225
160
36135
... More
Finishing with premium Interior emulsion paint system of berger/ asian /Nerolac/Spectrum paints using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm all complete as per direction of Engineer in charge
1810
193
350597
... More
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture
187
176
32958.75
... More
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture
1022
170
174455.4
... More
Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives. 13.48A.1 New work (Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.
319
181
57818.75
... More
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work
2337
102
240243.6
... More
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
225
156
35111.25
... More
Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete
300
19
5925
... More
Polishing on wood work with ready made wax polish of approved brand and manufacture : Old work
67
99
6686.6
... More
Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm).
5385
80
434300.25
... More
Melamine polishing on wood work (one or more coat).
25
1192
29807.5
... More
Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in charge.
4
288
1152.4
... More
Providing and fixing APP (Atactic Polypropylene Polymer) modified prefabricated five layer 2 mm thick water proofing membrane, black f inished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrance manufacture of density at 25°C, 0.87 - 0.89 kg/ litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using Butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/ 5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacture of membrane. 14.89.1 2 mm (for corrugated roof sheets)
35
498
17442.25
... More
Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black f inished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : 3 mm thick
2317
537
1245271.65
... More
Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.
209
3
721.05
... More
Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge.
25
3
96.25
... More
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
10
1503
15036
... More
Dismantling tile work in floors and wall laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm
431
73
31635.4
... More
Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead
373
266
99385.85
... More
Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.
5
112
560.25
... More
Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping groundwithin 50 metres lead.
225
54
12296.25
... More
Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineerin-charge
50
56
2817.5
... More
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar
2
2060
4120.4
... More
Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.
61
7993
487621.8
... More
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern.
595
1091
649442.5
... More
Extra for providing and mixing hardening compound of approved quality as per manufacturer’s specification in cement concrete.
100
55
5550
... More
Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)
800
5
4240
... More
Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge)
17.25
10117
174528.6
... More
Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)
120
375
45096
... More
Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment). Overhead informatory road signage
4.5
5879
26459.55
... More
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in charge. Made of G.I. wire of dia 4 mm
318
1017
323660.4
... More
Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern
1
18008
18008.75
... More
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
3
2648
7946.55
... More
Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
3
1034
3104.4
... More
Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia
3
6940
20822.25
... More
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm
3
1361
4085.4
... More
Proving and Fixing 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) with all screw, joint filler , joint finisher , joint tape roll ,primer for all height all complete as per direction of Engineer in Charge
50
878
43947.5
... More
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe 32 mm dia
3
119
358.65
... More
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & f ixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern f ittings, nuts, bolts and gasket etc complete.
2
14999
29998.3
... More
Providing and fixing 100 mm sand cast Iron grating for gully trap.
2
53
106.5
... More
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
20
168
3367
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 15 mm nominal dia Pipes
30
286
8604
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm nominal dia Pipes
20
401
8031
... More
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work 25 mm nominal dia. Pipes.
25
355
8885
... More
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter
4
222
889.4
... More
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
2000
11
22000
... More
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: 15 mm nominal bore.
6
506
3040.8
... More
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 :15mm nominal bore
10
574
5743
... More
Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length.
20
121
2438
... More
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
20
1505
30105
... More
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm
8
303
2426
... More
Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer-in-charge
24
109
2623.2
... More
Providing and fixing 12mm thick frameless toughened glass of approved brand and manufacture, including making necessary holes all complete as per direction of Engineer in charge
10
3981
39812
... More
Grading roof for water proofing treatment with : Cement mortar 1:3 (1 cement : 3 coarse sand)
58.16
16112
937079.74
... More
Providing, erecting, laying and fixing in position in 3.5 to 4 mm thick bamboo mat corrugated sheet (BMCS) as per IS: 15476-2004 in roofing with self drilling screws along with EPDM washers complete or with galvanized iron J or L hooks 8 mm dia G.I. plain and bitumen washers etc, all complete as per direction of Engineer-in-Charge
204
6012
1226468.4
... More
Providing and fixing in position ridges of 3.5 to 4 mm thick bamboo mat ridge cap (BMRC) as per IS: 15476-2004 in roofing with self drilling screws along with EPDM washers complete or with galvanized iron J or L hooks 8 mm dia G.I. plain and bitumen washers etc, all complete as per direction of Engineer-in-Charge.
33
4830
159393.3
... More
Providing and fixing at Bamboo Mat board conforming to IS:13958-1994 for partition to frame by bucking or studding with screws etc. complete (Frames, backing or studding to be paid separately)
19
3332
63308
... More
Providing and fixing 15 mm thick false ceiling tiles at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity 0.043 W/m K as per ASTM 518:1991,in true horizontal level on the existing frame work consisting of T-sections and Lsections suitably fixed according to tile size as per direction of Engineer-in-charge.
27
1781
48092.4
... More
Providing and fixing new cricket practice pitch net made up of HPDE with section 50x50mm with dia of thread as 2.5 mm thick of Garware make or equivalnet for safety passserby from cricket ball all complete as per the direction of Engineer-in charge
555
273
151681.5
... More
Providing and fixing of Fabric of Awnings at existing Gazebo or shade stands of DIKSON make or equivalent, mininum 600 gsm rates are inclusive removing of damaged fabric , replacing with new fabric for all heights all complete as per direction of Engineer In charge .
600
2755
1653000
... More
Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). all complete as per direction of engineer in charge
128
3622
463724.8
... More
Providing fixing and designing of Animated Eco Solvent Flex printing work, All the designs / Pictures will be suggested and selected by Engineer in chage as per site requirement, these Images will be print in Heigh Resolution Pictures Printed in 10 Colours and to be printed at Self Glued Vinyl / Flex All the Work will be Completed as per the directions of Engineer In charge.
23.2
3214
74578.72
... More
Providing and fixing of multi vent roof ventilators (turbo ventilator) on the top of roof with high performance industrial multi vent room ventilator of Minimum 530 mm dia neck/throat of Aluminium alloy designed to a capacity of 1850 CFM at a high of 25 feet including Polycorbonate stretched from 3.00 mm thick sheet venture dome 1.5 mm thick and all required accessories as per technical specification. Multi roof ventilators to be got approved from Engineer-in-charge before installation. The rate includes cutting /making holes in the existing roofing sheets.
8
8836
70692
... More
Providing and Fixing rectangular shape grating of 350 mm width and 20 mm depth of standard configuration of white /blue or any combination of colour made up of Polypropylene material i/c pvc angle 40x25x4 on both side of drain as per the existing similar design all complete as per the direction of Engineer in charge.
80
1112
89032
... More
Providing and fixing swimming ladder of stainless steel grade 304 ,Ladder width : 500 mm No of Steps : 4/6 Steps Surface Treatment :Polished complete as per Direction of Engineer in charge
3
20201
60603
... More
Providing & fixing chrome plated brass Shower diverter with conceal single lever body make Jaguar or equivalent as per the existing similar design all complete as per the direction of Engineer in charge.
4
5515
22062.8
... More
Providing & fixing chrome plated brass pillar cock, including extension body of make Jaguar or equivalent as per the existing similar design having foam flow technology all complete as per the direction of Engineer in charge. 15 mm nominal bore
4
4201
16807.6
... More
Providing & fixing chrome plated brass Health/hand faucet/hand jet spray of make Jaguar or equivalent as per the existing similar design all complete as per the direction of Engineer in charge.
5
1387
6935.5
... More
Providing and fixing Patch glass door lock with SS Cover at the existing toughened glass door of approved brand and manufacture, including arrangement etc. all complete as per direction of Engineer-in-charge.
10
3339
33397
... More
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)
20
1355
27116
... More
Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. a. All kinds of soil
224
177
39760
... More
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.
74
196
14504
... More
Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.
A.All kinds of soil
116
126
14708.8
... More
Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level.
A. Thermo-Mechanically Treated bars of grade Fe-500D or more.
1100
107
118635
... More
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)
88
7370
648617.2
... More
15 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand)
209
411
86055.75
... More
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level: All types of soil 300 mm dia
200
707
141550
... More
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.
a. 200 mm nominal size dia
200
1113
222670
... More
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.
a. 200 mm nominal size dia
160
1255
200912
... More
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
9
1509
13588.2
... More
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer in-charge.
9
1538
13844.25
... More
Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.
9
1538
13844.25
... More
Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer in-charge.
18.84
2024
38141.58
... More
Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge.
20
1399
27999
... More
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of useable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully eveloped,measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
20
1085
21701
... More
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:
a. 200 mm dia each
4
321
1284.6
... More
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.A. 200 mm clamp
4
2293
9174.6
... More
Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). A. 200 mm dia
4
357
1430.4
... More
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :300 mm dia. R.C.C. pipe
523
994
520018.9
... More
Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 19.11.1 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
5
24702
123513.75
... More
Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
48
5957
285979.2
... More
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.
20
553
11074
... More
Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : 19.29.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
3
11520
34561.65
... More
Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated and then returning the soil as required, in layers not exceeding 20 cm depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within alead of 50 m : 2.10.41 cm All kinds of soil . Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
523
352
184174.45
... More
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood
0.5
142949
71474.85
... More
Extra for additional labour for circular works, such as in frames of fan light Second class teak wood
0.1
14294
1429.5
... More
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: Butt hinges and necessary screws shall be paid separately) Second class teak wood 1 mm thick shutters
25
4111
102798.75
... More
Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor f inishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer in-charge With brass cover plate minimum 1.25 mm thickness
20
2966
59322
... More
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix)
137.5
2434
334709.38
... More
Supplying chemical emulsion in sealed containers including delivery as specified: Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
391
234
91787.25
... More
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement: 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
341
310
105727.05
... More
Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
1173
43
50439
... More
Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.
100
279
27930
... More
Dismantling/ Removing and Refixing of Hard maple wood tongue and grooved planks - supported by pine/spruce/fir padded runners of section 63.5mm x 38mm placed with distance between the runner to be 9 along the width of the court, Imported safe sleeper shock absorption pads of 8 mm thick be be provided under the runners for shock absorption. A vapor barrier of 1000 micron will also be intorduced between sub floor and frame work. The frame will be duly fastened to the sub floor with the aid of clamps. The floor will be duly levelled with three pahse machine grinding, joint sealing with French chalk and sanding sealer followed by polishing with polyunethane finish.Also the work includes painting of game lines in required colors/dimensions .
170.5
846
144328.25
... More
Providing and fixing of 20mm (thickness) x 57mm (width) imported Hard maple wood tongue and grooved planks - WSF approved supported by pine/spruce/fir padded runners duly treated with wood life anti treatment of section 63.5mm x 38mm placed with distance between the runner to be 9" along the width of the court, Imported safe sleeper shock absorption pads of 8 mm thick be be provided under the runners for shock absorption. A vapor barrier of 1000 micron will also be intorduced between sub floor and frame work. The frame will be duly fastened to the sub floor with the aid of clamps. The flooor will be duly levelled with three pahse machine grinding, joint sealing with French chalk and sanding sealer followed by polishing with polyunethane finish (of WSF approved manufacturer/flooring system).Also the work includes painting of game lines in required clours/dimensions and anti-termite treatment of concrete floor base (anti termite work for outer walls shall be paid separately). (The rates includes dismantling of existing flooring).
170.5
11091
1891134.85
... More
Removing & installation of badminton court Mat(Flooring ) Including supply and installation of Double side tape ; side tape & welding rods.
2
35566
71132
... More
Electrical Work
Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required.
a) Group C
110
894
98340
... More
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulatedcopper conductor single core cable etc. as required.
a) Group C
55
1467
80685
... More
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
a) Group C
110
1845
202950
... More
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
200
233
46600
... More
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
100
275
27500
... More
2 X 4 sq. mm + 1 X 4 sq. mm earth wire
235
334
78490
... More
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
90
439
39510
... More
2 X 10 sq. mm + 1 X 6 sq. mm earth wire
45
570
25650
... More
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
180
327
58860
... More
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
110
369
40590
... More
2 X 4 sq. mm + 1 X 4 sq. mm earth wire
290
428
124120
... More
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
120
589
70680
... More
2 X 10 sq. mm + 1 X 6 sq. mm earth wire
40
710
28400
... More
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required. 3 x 1.5 sq. mm
90
95
8550
... More
6 x 1.5 sq. mm
110
181
19910
... More
3 x 2.5 sq. mm
90
137
12330
... More
3 x 4 sq. mm
145
206
29870
... More
6 x 4 sq. mm
100
396
39600
... More
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
110
47
5170
... More
Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.
1
-
-
... More
20 mm
50
223
11150
... More
25 mm
70
256
17920
... More
32 mm
60
326
19560
... More
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and
1
-
-
... More
20 mm
50
128
6400
... More
25 mm
70
145
10150
... More
32 mm
40
184
7360
... More
Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc.as required.
1
-
-
... More
1 or 2 Module (75mmX75mm)
12
298
3576
... More
3 Module (100mmX75mm)
25
327
8175
... More
4 Module (125mmX75mm)
12
343
4116
... More
6 Module (200mmX75mm)
24
402
9648
... More
8 Module (125mmX125mm)
10
454
4540
... More
12 Module (200mmX150mm
12
547
6564
... More
Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.
1
-
-
... More
1 or 2 Module
24
133
3192
... More
3 Module
24
151
3624
... More
4 Module
12
158
1896
... More
6 Module
30
182
5460
... More
8 Module
12
211
2532
... More
12 Module
6
272
1632
... More
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
1
-
-
... More
5/6 A switch
225
103
23175
... More
15/16 A switch
90
156
14040
... More
3 pin 5/6 A socket outlet
25
122
3050
... More
6 pin 15/16 A socket outlet
90
197
17730
... More
Telephone socket outlet
12
148
1776
... More
TV antenna socket outlet
10
148
1480
... More
Bell push
18
140
2520
... More
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
25
369
9225
... More
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
20
586
11720
... More
Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
75
87
6525
... More
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
1
-
-
... More
4 way (4 + 12), Double door
6
4091
24546
... More
6 way (4 + 18), Double door
10
4974
49740
... More
8 way (4 + 24), Double door
10
5967
59670
... More
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
1
-
-
... More
Single pole
400
256
102400
... More
Single pole and neutral
24
599
14376
... More
Three pole and neutral
12
1228
14736
... More
Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.
1
-
-
... More
40 A
8
970
7760
... More
63 A
12
1034
12408
... More
100 A
10
1227
12270
... More
Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess i/c providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.
20
727
14540
... More
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
6
6855
41130
... More
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as
required.
50
244
12200
... More
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
30
706
21180
... More
Providing and fixing following rating and breaking capacity and pole MCCB with thermo-magnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.
1
-
-
... More
100 A,30KA,FPMCCB
5
7723
38615
... More
125 A,36KA,FPMCCB
5
8209
41045
... More
250 A,36KA,FPMCCB
5
17510
87550
... More
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)
180
55
9900
... More
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
50
130
6500
... More
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.
400
42
16800
... More
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.as required.
1
-
-
... More
100 mm width X 50 mm depth X 1.6 mm thickness
50
669
33450
... More
Supplying of 20 watt 4 feet long LED Batten, with extruded aluminium housing & poly-carbonate diffuser with integrated LED driver directly on wall / surface including connection with 1.5 mm2 FRLS PVC insulated copper conductor single core cable and earthing etc. including testing & commissionong as reqd.
70
537
37590
... More
Supply, Installation, Testing and Commissioning of ceiling fan BEE Star rated Decorative ceiling fan having copper winding, 3 nos. blades, down rod, 2 nos. canopies, shackle kit and all remaining accessories including safety pin, nut bolts, washers etc. suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
1
-
-
... More
1400 mm sweep decorative minimum 1 star rated.
12
4538
54456
... More
Supply, Installation, Testing and Commissioning of ceiling fan 1200 mm sweep, BEE star rated ceiling fan having copper winding, 3 nos. blades, down rod, 2 nos. canopies, shackle kit and all remaining accessories including safety pin, nut bolts, washers etc. suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
12
2873
34476
... More
Supplying, Installation, Testing and Commissioning of 36 watt 2ft x 2ft recessed/surface mounted high efficient LED light fitting minimum 3600 lumen fabricated with deep drawn CRCA sheet steel housing duly power coated with high efficient LEDs &glare free full ,opal diffuser, IP 20 i/c connection etc. complete as required.
55
3426
188430
... More
Supplying and fixing of Surface/recess Mounting18 Watt LED light fitting 1'X1' fabricated with CRCA sheet steel housing duly power coated with high efficient LEDs & glare free full ,opal diffuser, IP 20 etc as required.
30
1045
31350
... More
Supplying and fixing of Surface/recess Mounting 18/20 Watt LED down lighter suitable for existing light cuttings with high efficient LEDs & glare free full ,opal diffuser, IP 20 etc as required.
30
1045
31350
... More
Supplying, Installation, Testing and commissioning of 100 Watt LED flood light fitting complete with suitable lens & other accessories highly efficient made of pressure die cast aluminium housing ,extruded aluminium heat sink& enclosed with toughened glass IP-66 protection and having lumens not less than 11000 & fitting wattage not more than 100 watt i/c making suitable arrangement according to LED flood light fitting i/c connection testing complete as per technical specifications attached etc as required.
10
8479
84790
... More
Supplying, Installation, Testing and commissioning of 200 Watt LED flood light fitting complete with suitable lens & other accessories highly efficient made of pressure die cast aluminium housing ,extruded aluminium heat sink& enclosed with toughened glass IP-66 protection and having lumens not less than 22000 & fitting wattage not more than 200 watt i/c making suitable arrangement according to LED flood light fitting i/c connection testing complete as per technical specifications attached etc as required.
15
14519
217785
... More
Supplying and fixing of 9 Watt Recessed LED down lighter with Cob Technology suitable for existing light cuttings with high efficient LEDs & glare free full ,opal diffuser, IP 20 etc as required.
50
1434
71700
... More
Supplying and fixing of 5 watt /mtr LED strip light wirh driver& high efficient LEDs with long life , IP 20 etc as required.
200
251
50200
... More
Supply & installation of following size exhaust fan(metallic body) heavy duty i/c connections, making good the damages ,iron angle & painting with screws,nuts & bolts with testing & commissioning etc. complete as required.
1
-
-
... More
300 mm or 12 "
4
4903
19612
... More
380 mm or 15"
2
6073
12146
... More
600 mm or 24 " (Three Phase)
2
15960
31920
... More
Supply and fixing of following type/size wall and padestal fan i/c connection, testing etc complete as required.
1
-
-
... More
400 mm wall fan ( 3 nos blade).
10
3046
30460
... More
450 mm pedestal fan
6
5325
31950
... More
Supply of PVC insulated and PVC sheathed / XLPE armoured aluminium conductor power cable (As per IS 7098(Part-1) of 1.1 KV grade i/c connection testing etc.as required.
1
-
-
... More
2X6 Sq.mm
100
198
19800
... More
4x10 sq.mm
150
355
53250
... More
4x16 sq.mm
160
380
60800
... More
3.5x50 sq.mm
60
765
45900
... More
3.5x70 sq.mm
50
1030
51500
... More
Repairing & rewinding of existing 600/450/380 mm heavy duty exhaust fan i/c deffective parts and painting with 2 or more coats of superior quality enamel paints etc.complete as required.
3
1610
4830
... More
Repairing of existing cubical recess mounted electrical panel board including dressing of wiries, replacement of wornout connectors, neutral link, din bar etc. whichever found deffective and painting with 2 or more coats of enamel paints etc.complete as required.
6
3462
20772
... More
Supply and fixing of different type flexible metal pipe for proper arrangements of loose wires i/c shaddling etc as required.
85
121
10285
... More
SITC of following size PVC Trunking with complete accessories.
1
-
-
... More
DLP mini-trunking 80 x 50 mm and accessories
80
1069
85520
... More
DLP PVC trunking 105 mm x 50 mm and accessories
80
1681
134480
... More
DLP PVC trunking 150 mm x 50 mm and accessories
50
2502
125100
... More
Modified Estimated cost after using correction factor on account of GST@ 0.027 From item no 1 to 137 (CIVIL WORK ONLY)
1
567795
-567795.59
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements