Delhi Development Authority Tender

Providing and laying in position 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) reinforced cement concrete foundation of size 450 mm x 450 mm x 1200 mm deep (800 mm below ground level and 400 mm above ground level) including excavation of earth, refilling, providing, cutting, bending and placing in position, reinforcement of cold twisted bars of 12mm. dia-1200mm long (approx..) -8Nos, and reinforcement ring of cold twisted bar of 8mm dia -1400mm long (approx..) -6 nos., (with suitable spacing) including centring & shuttering as required with providing, fixing and positioning of one set of foundation bolts comprising of 4 nos., 16 mm dia, 750 mm long J-Type MS bolts (Threaded portion shall be galvanized) along with 3 nos. GI nuts and 2 nos. GI washers etc. per bolt and 1 no. anchor plate (3mm thick) of suitable size and providing 63 mm.(O.D) DWC pipe ISI marked for cable entry & exit etc. complete as required.

Supplying, replacement and commissioning of 45 watt LED street light fitting (IP-66) made out of pressure die cast Aluminium housing & enclosed with toughened glass, driver, lens, all accessories, suitable mounting arrangement (bracket)on existing pole, if required, and providing suitable size of wiremesh protection frame/guard for safety purpose, connection, testing etc. as required.

Supplying, replacement, installation, testing & commissioning of 80 Watt LED flood light fitting with lens IP-66 made of pressure die cast aluminium housing with toughened glass complete with LEDs, driver, all accessories and providing & fixing wire mesh protection frame for safety purpose, connection, testing etc. complete as reqd.

Supplying, installation, testing and commissioning of 40 watt post top lantern (for gate light), with aluminium canopy and die cast aluminium offers symmetric light distribution with clear acrylic diffuser i/c connection testing etc complete as reqd.

Supplying, installation, testing and commissioning of down lighter type 40 watt well glass luminaires, pressure die cast aluminium housing with led as light source i/c providing all fixing accessories , fixing on roof ,connection testing etc complete as reqd.

Supply and installation of 24 W Led Strip on the existing gates at the entrance of DDA park sec 16 D Dwarka i/c jointing at suitable places with connector and making water proof joints, testing commission etc. complete as required.

Supply, replacement & installation of pole connector box made out of Glass Reinforced Polyester Sheet Moulding Compound to IS : 13410-1992 grade S1 of outside dimensions 280 mm(H) x 170 mm(W)x 115 mm (D) (all the corners of the box should be round & not pointed ones) suitable to mount on 40/50/65/80 mm dia GI pole with the following provisions/accessories mounting in box complete as reqd.(i)2 nos. clamps made out of 19mm x 3 mm M.S. strip of suitable length for mounting box on the pole.(ii) Water tight front cover with 2 nos. stainless steel hinges & 1 no. screw for tightening.(iii)4 way, 220 V, 30 A, dough moulded connector (SMC with stainless steel inserts)(iv) 16 amp. Moulded SMC rewireable kit-kat---1 no.(v) Suitable size hole at suitable location on rear wall for cable & wire entry.(vi) Earthing bolt M6 x 20 mm

Supplying & drawing following size FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit as required. a)3 x 1.5 sq. mm

Supplying of following sizes of XLPE insulated PVC sheathed Al. cond. Armoured power cable of 1.1 KV grade including connection, testing etc. as required. a) 2C x 16 sq. mm

b) 4C x 25 sq. mm

c) 4 C x 50 Sq mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required. a)Upto 35 sq. mm

b) Above 35 sq.mm and upto 95 sq.mm

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. Direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. a)63 mm dia (OD-63 mm & ID-51 mm nominal)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/recessed conduit/sub main wiring/cable as required.

Supplying , fabrication & fixing of wooden extension board of suitable size including 16 amp power socket, and switch in 5 numbers each including in internal wiring of size 6 sq. mm. with copper wire with with all accessories & extra 2 mtr. Wire for input supply complete as required.

Supplying, replacement ,installation, testing and commissioning of Meter panel with floor mounted cubical type double door of size of 1000 mm x 900 mm x 300 mm deep duly compartmentalized and with general arrangement made out of 2mm thick CRCA sheet having hinged gasket cover and screwed knobs with double locking arrangement and rain protection covers 100 mm and supported with of MS angle iron legs and bottom frame of size 35mm x 35mm x 5mm x 1mtr. long grouted with 1:3:6 CC foundation and should be 0.7 mtr. above ground level. Legs should be covered with brick walls, connections, inter connections with suitable size of FRLS PVC insulated copper conductor using thimbles wherever required, painting, numbering including supply and fixing of following accessories complete etc. as required. (a)250 Amps. ,50 KA Four Pole MCCB ('C'-Series)----1 No. (b)100 Amps. 30 KA Four Pole MCCB ('C'-Series)------ 3Nos. (c)30 Ampere 4 way neutral link/connector ------2 Nos. (d)16 Amps industrial Socket suitable for three phase supply- 2 Nos. (e) Voltmeter (0-500 Volt) 96mm X 96mm square type with selector switch ---1 No (f) Phase Indicating Lamp Set with fuses ----1 Set (g) Danger notice plate -----1 No (h) AI. Bus Bar suitable 250 amp. 4 strip, with sleeve and nut bolts-----1 Set. (i) Ammeter (0-30Amp) 96mm X 96mm square type ----1No. (j) Lifting hook on the top of panel board and lighting arrangement inside the feeder pillar---- 1 No. (k) Space for electric metre

Supplying, replacement, installation, testing and commissioning of feeder pillar with floor mounted Light control LT feeder pillar cubical type double door of size of 1000 mm x 900 mm x 300 mm deep duly compartmentalized and with general arrangement made out of 2mm thick CRCA sheet having hinged gasket cover and screwed knobs with double locking arrangement and rain protection covers 100 mm and supported with of MS angle iron legs and bottom frame of size 35mm x 35mm x 5mm x 1mtr. long grouted with 1:3:6 CC foundation and should be 0.7 mtr. above ground level. Legs should be covered with brick walls, connections, inter connections with suitable size of FRLS PVC insulated copper conductor using thimbles wherever required, painting, numbering including supply and fixing of following accessories complete etc. as required. (a)125 Amps. ,36 KA Four Pole MCCB ('C'-Series)----1 No. (b)16 Amps. single Pole MCB ('C'-Series)------ 6 Nos. (c)Timer Switch - 1 No. (d)32 Amps. AC-3, 3 pole power contactor -----1 No. (e)30 Ampere 4 way neutral link/connector ------2 Nos. (f)16 Amps industrial Socket suitable for three phase supply- 2 Nos. (g) Voltmeter (0-500 Volt) 96mm X 96mm square type with selector switch ---1 No. (h)Ammeter (0-30Amp) 96mm X 96mm square type ----1No. (i) Phase Indicating Lamp Set with fuses ----1 Set (j) Danger notice plate -----1 No (k) AI. Bus Bar suitable 125 amp. 4 strip, with sleeve and nut bolts-----1 Set. (l) Lifting hook on the top of panel board and lighting arrangement inside the feeder pillar---- 1 No.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Painting of existing ring type bracket(which is mounted on 8/6 meter pole)with suitable color with two coat suitable enamel paint with primer etc complete as reqd.

Supplying/fixing of PVC insulated copper conductor flat submersible cable of size 1 x 3 x 2.5 sq. mm i/c connection testing etc. compete as reqd.

Hiring of 125 KVA DG Set (Cummins make ) for Palash event at DDA park sec-16 D for 3 days i/c supply of 150 ltr. Diesel and 1 no. skilled operator for 3 days for operation i/c testing .commissioning etc. complete as required.

Supplying, Fabrication and replacement of wire mesh protection frame for existing feeder pillar made out of 8 SWG M.S wire mesh size (75mm X25mm rectangle nominal) of following size with base frame made of M.S angle iron 35mm x 35mm x 5mm and with M.S strip support of size 35mm X 5mm in cross and 0.5 mtr long legs support of same angle iron (as per drawing attached) , i/c door in front portion, supplying and fitting of godown lock i/c locking arrangement, painting and grouting of angle iron frame with legs in CC 1:3:6 foundation etc. as approved by Engineer-in-charge etc. complete as reqd.a) 2 mtr (H) X 1.5mtr (W) X 1.0 mtr (D)

Repairing of existing feeder pillar with 2 mm thick CRCA sheet including welding providing required no. of hinge, painting etc. complete as required.

Repairing of Existing wiremesh protection frame including replacement of 6 SWG M.S. wiremesh size (75mm x 25 mm) rectangle nominal size i/c replacement / repair of looking arrangement, nut- bolts etc. complete as required.

Painting and numbering (2 coating) of existing G.I. pole of upto 4 /6 mtr. hight including painting of base plate & mounting arrangement etc. complete as reqd.

Painting of existing wire mesh protection frame/ panel of different size with 2 Nos of enamel paint coating including primer, cleaning etc. complete as required.

Repairing of existing 8 mtr semi high mast foundation/panel foundation with CC mortor from one feet below ground level, i/c entering the existing cable through the foundation upto the connector box i/c filling up of gap between base plate and foundation etc. complete as reqd.

Repairing of existing 4 mtr. square foundation with CC mortor from one feet below ground level, dismantling of existing pole for cable entry/exit i/c entering existing cable through the foundation upto the connector box etc. complete as reqd.

Providing& laying of DWC pipe of size 63 mm outer dia, by trenchless technology with no dig method by making bore hole in horizontal direction across the road/path with boring equipment i/c jointing / cleaning of pipes, excavation of pits of required size & depth etc. complete as required.

Fabrication, supplying and fixing of wire mesh protection guard made out of MS strip and 10 SWG dia. wire suitable for 40 Watt decorative post top light fitting as approved by Engineer-in- charge completed etc. as reqd.

Painting of existing foundation of 4/6/8 Mtr. pole with two coat suitable enamel paint with primer ,putty etc complete as reqd.

Shifting of exiting 4 Mtr. pole with foundation from one location to other location and reinstallation the same including connection ,testing ,commissioning etc complete as required.