Delhi Development Authority Tender

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Air Walker: Providing and fixing air walker with below specifications: 1. Dimensions (LxWxH): 1100 x 550 x 1480mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. ‘U’ shaped main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. All other pipes of NB 32mm (G.I.) ‘C’ Class (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. Foothold made of nylon alloy with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Sit up Station: Providing and fixing double sit-up station with below specifications: 1. Dimensions (LxWxH): 1500 x 1150 x 650mm 2. Fabricated with base frame of NB 50mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. 4. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. Fixed on its top is back support made of perforated MS sheet of 2mm thickness. 6. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. 7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 8. Zinc primer paint is applied at all welding points prior to finishing. 9. The equipment to be fixed on ground with concrete of minimum strength M-25 and Expansion Bolts. 10. Once the concrete is set, the equipment is fixed on to it. 11. High tensile steel with galvanized nut bolts are used for assembly. 12. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 13. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Air Swing: Providing and fixing air swing in a pair with below specifications: 1. Dimensions (LxWxH): 1150 x 900 x 1250 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 40mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Foothold made of nylon alloy with rounded edges to prevent impact and injury. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Horse rider station: Providing and fixing horse rider station with below specifications: 1. Dimensions (LxWxH): 1000 x 600 x 1100 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 9. Foothold made of NB 25mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Leg Press: Providing and fixing leg press in a pair with below specifications: 1. Dimensions (LxWxH): 1750 x 550 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. 9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Pull chair: Providing and fixing pull chair in a pair with below specifications: 1. Dimensions (LxWxH): 1950 x 700 x 2000 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Seated Chest Press: Providing and fixing seated chest press in a pair with below specifications: 1. Dimensions (LxWxH): 1800 x 700 x 2000 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Arm wheel: Providing and fixing arm wheel in a pair with below specifications: 1. Dimensions (LxWxH): 850 x 800 x 1800 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame wheel of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 11. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 12. High tensile steel with galvanized nut bolts are used for assembly. 13. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 14. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Elliptical exerciser: Providing and fixing elliptical exerciser with below specifications: 1. Dimensions (LxWxH): 1200 x 540 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 12. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 13. High tensile steel with galvanized nut bolts are used for assembly. 14. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 15. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Double cross walker: Providing and fixing double cross walker with below specifications: 1. Dimensions (LxWxH): 1600 x 600 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 4. Foot support frame of 100 x 50 x 2.5mm CRC rectangular pipe. 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. Foothold made of nylon alloy with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Twister: Providing and fixing triple twister with below dimensions: 1. Dimensions (LxWxH): 1700 x 1300 x 1300 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. 4. Handle frame support of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. Foothold plate of made of cast iron of 12mm thickness. 6. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 8. Zinc primer paint is applied at all the welding points prior to finishing. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with concrete of minimum strength M-25 and Expansion Bolts. 11. Once the concrete is set, the equipment is fixed on to it. 12. High tensile steel with galvanized nut bolts are used for assembly. 13. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 14. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Rowing machine: Providing and fixing rowing machine with below specifications: 1. Dimensions (LxWxH): 1280 x 800 x 1150 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 9. Foothold made of NB 65mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Weight Assisted Shoulder Press: Providing, designing and fixing of weight assisted Shoulder Press fabricated with main pipe of ‘ C’ Class GI Pipe with minimum 75 mm dia and other pipes of 60mm dia and joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Machine to have weight plate adjustment arrangement made of 202 grade stainless steel and designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for adjustment. Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and once the concrete is set, fix the equipment on to it. All complete as per direction and approval of Engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipment etc. (the cement concrete and excavation work shall be paid separately). Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Weight Assisted Chest Press : Weight Assisted Chest Press Providing, designing and fixing of weight assisted Chest Press fabricated with main pipe of ‘ C’ Class GI Pipe with minimum 75 mm dia and other pipes of 60mm dia and joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Machine to have weight plate adjustment arrangement made of 202 grade stainless steel and designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for adjustment. Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and once the concrete is set, fix the equipment on to it. All complete as per direction and approval of Engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipment etc. (the cement concrete and excavation work shall be paid separately). Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Weight Assisted Lat Pull Down: Providing, designing and fixing of weight assisted Lat Pull Down fabricated with main pipe of ‘ C’ Class GI Pipe with minimum 75 mm dia and other pipes of 60mm dia and joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Machine to have weight plate adjustment arrangement made of 202 grade stainless steel and designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for adjustment. Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and once the concrete is set, fix the equipment on to it. All complete as per direction and approval of Engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipment etc. (the cement concrete and excavation work shall be paid separately). Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Weight Assisted Rowing Machine: Providing, designing and fixing of weight assisted Rowing Machine fabricated with main pipe of ‘ C’ Class GI Pipe with minimum 75 mm dia and other pipes of 60mm dia and joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Machine to have weight plate adjustment arrangement made of 202 grade stainless steel and designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for adjustment. Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and once the concrete is set, fix the equipment on to it. All complete as per direction and approval of Engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipment etc. (the cement concrete and excavation work shall be paid separately). Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label fixed on equipment for ease of use.

Providing and fixing label of equipment made of stainless steel 0.7 mm thick and fixed to the vertical post of gym equipment with stainless steel 6 nos. rivets and instructions printed by Lazer printing with computer programme i/c text writing and photo of the equipment all complete as per direction of Engineer in charge. 220 x110 mm size

Schedule - 'B' 1.Regular maintenance of three years of all the Gym Equipments (16 nos.per set) installed in DDA parks of East Zone (SPECIALIZED WORKS) as per schedule consisting following:- a. Inspect and adjust of drive, timing and running belts. b. Check and set right/replacement of ball bearings, misaligned moving points, adjust/tighten loose parts, covers; seats, foundation and flooring. c. Tighten of nuts/bolts/screws i/c welding of various part/joints of Equipment wherever required. d. Calibration of instruments. e. Priming coat & painting coat, if required. f. Lubrication/oiling. g. Replacement of damaged parts & rectification of any others defects observed as per direction of Engineer-in-charge except. (i) Due to Force majeure of (ii) Abnormally bad whether serious loss or damage by fire or (iii) Damage due to act of god or (iv) Any other cause which in the absolute discretion of the Engineer-in-charge is beyond the contractors control as theft of any parts. A)Maintenance of equipments for the third year after initial two years of maintenance carried out by the agency at his own cost

B)Maintenance of equipments for the fourth year

C)Maintenance of equipments for the fifth year

Note:-

(i) All the pipes should be G.I. ‘C’ class, ISI marked.

(ii) The maintenance of equipment for initial two year after actual date of completion of the work shall be carried out by the agency at his own cost. The three years maintenance period as per the schedule above shall be reckoned after expiry of two year of maintenance period.

(iii) It will be the responsibility of the agency of keep all the fitness equipment in fully working condition 24x7. If agency fails to bring the fitness equipment back in working condition within 48 hours after receiving of the complaints, the agency shall pay Rs. 1000/- per complaint per day to the department.

(iV) An amount equal to 10% of the cost of work against item No-6 to 21 in schedule-A shall be retained as additional Security Deposit, in addition to the Security Deposit mentioned elsewhere in contract form. The amount so withheld would be released after five years from the date of completion of the entire work under the Agreement, if the performance of the work done is found satisfactory. However, the Security Deposit so deducted may be released in full against bank guarantee of equivalent amount in favour of Engineer-in-charge, if so decided by the Engineer-in-charge.