Central Pollution Control Board Tender

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade. New work (two or more coats) over and including water thinnable priming coat with cement primer

Providing and fixing of ISI mark Door closers

12 mm cement plaster of mix 1:6 (1 cement : 6 fine sand)

Manufacturing, assembling. Transporting and placing in position knock down modular furniture such as office table, drawer unit, side rack, wall hung file storage cabinet, ward robe storage/ almirah etc configurated of modular panels of particle board as per drawing, specifications and direction of the Engineer-in-Charge. All outer exposed edges of all the panels shall be covered and sealed with 2mm thick pvc edge banding tape, Rehau or Dolkin or equivalent make and all concealed and butt edges of all panes shall be covered and sealed with 0.70mm thick pvc edge banding tape of same make with hot melt glue on edge banding machine at 200° c temperature. All joinery fabrication work shall be done with mini fix fittings and plastic dowels in approved factory including cost of mini fix fittings, pvc cable wire manager, Nylon glides 20mm, plastic dowels etc. (cost of providing and fixing of fittings to modular furniture such as drawer slides, self closing spring loaded hinges, multipurpose locks , knob/handles etc shall be paid separately)

18mm thick flat pressed, three layered pre- laminated particle board with both side decorative lamination (medium density) Grade I, type II conforming to IS:12823 (exterior grade)

25mm thick flat pressed, three layered pre- laminated particle board with both side decorative lamination (medium density) Grade I, type II conforming to IS:12823 (exterior grade)

Providing and fixing MS power coated knob oval shaped handles of ITALICA or equivalent make patent no. 163465 with screws complete

Providing and fixing multipurpose lock of Godrej/Plaza or equivalent make of approved brand and manufacturer to drawer of cub board with steel screws including making recess of required size in board and fixing of standard plate having groove meant for receiving locks lever in locked position etc complete as per direction of Engineer-in-Charge

Providing and fixing auto closing spring loaded hinges of Hettich/Ebco or equivalent make of approved brand to cupboard shutters with steel screws including making necessary recess in panel board and finished etc complete as per direction of Engineer-in-Charge

Providing and fixing powder coated telescopic drawer channel 405mm long with necessary screw etc complete as per direction of Engineer-in-Charge

French spirit polishing : Two or more coats on new works including a coat of wood filler

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 4 sq. mm + 1 X4 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

63 Amp 4 pole 415V Isolator

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 module (75mmx75mm)

8 module (125mmx 125mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

6 pin 15/16 amp socket outlet

6 pin 15/16 amp switch

Telephone socket outlet

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

4 pair

SITC of wall mounted cabin fan of 400 mm sweep i/c testing and commissioning etc. as reqd. (Bajaj/Khaitan/crompton/usha/ make)

Supplying and fixing of 3 modular GI box with modular plate and cover in front on surface or in recess, including providing and fixing 1 nos. of 6 pin 25 amps modular socket outlet and 1 nos. of 25 amps modular tiny trip MCB, connection etc. as required.(make :- North west /norysis/grabtree/roma)

Supplying and fixing of following size XLPE insulated and PVC sheathed alu. conductor armored power cable of 1.1 KV grade on the surface as reqd. (make Gloster / Havells/ Polycab/kalinga)

4 x 50 sq. mm

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Top Storage Unit (Overhead) 900(W)x320(D)x645(H) 2 shutters (glass with M.S frame) The Wall hung storages are made up of CRCA M.S. sheet of 1.0mm thick duly powder coated with the powder coating thickness of 50-60 microns. The storage has openable shutter made of Steel/glass. The shutters are fixed with self-closing hinges

Providing and fixing Roller blinds of imported translucent fabric

Total

Taxes, if any

Grand Total