Public Works Department Tender

M.S. Above Ground Pipe Supply, Installation, Testing and Commissioning of the following sizes of flange jointed / screwed / welded, M.S. Pipes of Class C (Heavy class) ISI marked including accessories such as MS bracket, U clamps with Anchor fasteners, tees / elbows / reducers / couplings / unions / bends / flanges / gaskets / Nut bolts etc., and laying on the surface including painting with one coat of anticorrosive primer and two coats of approved red enamel paint after laying and testing after Installation etc. as per specifications complete as required: 100 mm dia.

SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 4 Sq.mm x 4C CU. Cable

Sec.9.0 Operation & Maintenance Works SYSTEM OPERATION & MAINTENACE : Bidder shall indicate their charges for the following : Comprehensive preventive maintenance contract for the entire chilled water system & VRF System supplied / Installed by the HVAC contractor inclusive of all parts, consumables and labour for all equipment supplied as well as replacement of any equipment / component / part which can not be repaired to the satisfaction of the Client. The Operation contract shall also include operatrion of entire chilled water System & VRV System based on 2 persons for 2 shifts & 1 person for night shift and 365 days per year. Only operation cost shall be considered during defect liability period. 1st year Cost of maintenance shall be inclusive in the DLP and no extra payment will be paid for the maintenance in the first year after handing over. 2nd Year after DLP

Supplying, installation, testing and commissioning of 42U Floor standing 19" networking enclosure as per specification and complete with all accessories. (upto size - 800mmW x 1000mmD) as required. (along with horizontal cable manager & vertical cable manager, PDU with minimum 12 Nos. 16 Amp socket, as per technical specification etc. as required.

Supply, installation, testing and commissioning of cabinet type Floor Mounted / Loft Mounted Type single skinned Centrifugal Exhuast Air Unit; unit shall have leakproof canvass connection along with damper at suction side & descharge side cowl; ready to start unit hooked upwith 4P TEFC with IP 55 protection motor with pully / belt drive arrangement on adjustable frame; fan motor assembly mounted on corrossion proof-painted MS baseframe; baseframe to rest on vibration isolation pads. The unit shall be supplied with Starter Panel of required motor capacity. 3900 CFM / 40mm Static Pressure for Toilet

Sec.9.0 Flooring works Providing material and labour for laying Ceramic tiles 6mm thick in flooring treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) and fixed with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including finishing of joints, curing etc complete for all floors any heights, any lead and lift as directed by Engineer In charge. Sample and mockup shall be approvd before procurement of material.

Providing material and labour for laying integral cement based water proofing treatment (India type brick bat) including preparation of surface as required for treatment of roofs, balconies, terraces etc with average thickness of 120 mm and minimum thickness at khurra as 65 mm and consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer in- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with wired finish to receive china mosaic flooring. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge for all height all level.

Supply, Installation, Testing and Commissioning of Indication Lamp The module should have LED indication of calls, presences and reminders in the relevant colours conforming to VDE0834, consist of White,RED, Blue and Green LED chamber each with 3 ultrahigh LEDS up to 10,000 operating hours.

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. BLOCK-A EQUIPMENT NON-UPS PANEL As per Single line diagram

Providing and arranging in position work table with modesty panel without CPU hanger system of Enterprise 1500 of Godrej or equivalent of approximate size 1500 Width mm x 750 Depth mm x 725 Height mm with knock down construction system. Total assembly shall be maade of 25mm & 18mm thick prelaminated partical board of approved shade with PVC membrane pressed on it, PVC lipping at exposed edges, CRCA member and MS ERW tube finished epoxy polyster powder coating, Required hardware shall be provided i.e. wire management system, plastic cap for cable travel, leveler glide, handle, lock, sliding mechanisam etc.

Providing material and labour for fixing 25mm diameter (1.5mm thick) SS 316 satin (brush) finish Disabled Grab Rails/ handle of 600mm long of approved make with necessary SS 304 grade screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. BLOCK-B GROUND FLOOR EQUIPMENT NON UPS PANEL As per Single line diagram

Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required.

Supply & Installation of Under Deck Insulation with Class ‘O’ Nitrile Rubber with tough Aluminum foil facing & as per detail specifications - 25mm

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Single pair, 2-core, 1.5 sqmm, For PA System

INSULATED VALVES Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 32mm dia.

(f) 4C X 16 SQ. MM. CU XLPE CABLE

Design, Supply, Installation, Testing, and Commissioning of Chiller Plant Manager suitable to control 04 nos. of Water cooled chillers with VFD (2 Working + 1 Stand By + 1 Future provison), 04 Nos. Twin Cell Cooling Towers (2 Working + 1 Stand By + 1 Future provison), 04 nos. of Primary Pumps (2 Working + 1 Stand By + 1 Future provison), 04 nos. of Variable Frequency driven Secondary pumps (2 Working + 1 Stand By + 1 Future provison) & 04 Nos. of Condensor Pumps (2 Working + 1 Stand By + 1 Future provison) as per HVAC BOQ. The CPM shall be a 32 Bit microprocessor based, programmable controller, factory pre-programmed system housed in a IP54 rated panel enclosure of suitable size (and qty). Shall have integrated color graphics display for display of plant graphics, facility to change settings etc. Shall have on-board EPROM memory expandable through add-on memory card like micro SD card capable of storing sampled plant data for 5 years. Shall be capable of communicating with 3rd party BMS through Bacnet / IP. Shall have at least 2 nos. of on-board integrators for integrating chillers, open serial protocal like modbus RTU, grundfos bus, Wi Lo bus etc. Embedded web-server facility shall be optional. Shall do the function of time based scheduling, load based start / stop, run time equalization, trip / fault detection and annunciation of the high side refrigeration plant, namely; chillers, pumps, motorized on / off isolation valves etc. It shall also control the pumping system & shall co-ordinate with the primary side. Shall calculate plant load based on chilled water return header temperature. Price to include lump sum supply and laying of 2C x 1.0 sq mm armored FRLS signal cable from field sensor / actuators up to controller.

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing & Commissioning of Floor Mounted Air Handling Units as specified below; Double Skinned powder coated inner & outer skin of 0.6 mm & 43 mm thick, 40 kg / m3 PUF Sandwitched insulated aluminium sectionalized construction Comprising of Fan section with 50 mm static best efficiency Plug type Fan driven by suitable pole Eff - 1 TEFC Motor with Drive Package driven by IP55 / 4P TEFC Fan Motor / fire resistant flexible fan outlet connection, The AHU shall comprise filter section with Air filtering media with 10 micron pre filter, Cooling coil section with Chilled water Coil complete with Copper tube 13 FPI AL finned 4R deep chilled water cooling Coils, SS 304 condensate drain pan duly insulated with 15 mm thick cross linked polymer Nitrile rubber insulation, with Mixing box with Aluminium Aerofoil damper for supply, return & Fresh air, necessary vibration isolation arrangement by providing spring isolators ; Motor selection to suit the below capacity for each AHU rating by AC Vendor including transmission losses. ; Electrical Starter suitable for Respective AHUs, Panel supplied with matching rating for SA Fan motor, required DC Supply for control Valve, including short circuit / overload MCB protection, Motor Status On / Off / Trip, command, Automanual, Status contacts for remote operation through Operating Panels, Temperature Indicator availability on Panel with BAS compatiibility; Starter panel shall be minimum 14G MS powder coated with ventilation fan (only for VFD AHU Panels), inside light and duly internally wired and tested, Unit shall be supplied with Digital Thermostat with water proof casing BMS compatible with interface modbus / bacnet protocol to connect the BMS panel ; Prices to include dispatch of AHU in Semi-knocked down condition, assembly at site and lifting / shifting to actual locations as per layouts; Performance to be complied - common for below AHUs: dB=60 at 3 M distance; Price shall be complete with electrical Starters for each AHU matching the motor ratings and as specified above ; AHU dimensions, configuration (top discharge / side discharge), pipe connection side & door side shall be tailor made as per final layout and space constraints. No extra claim shall be payable for such customisation; Schedule below shows. 23.21 TR / 10250 CFM For Reception Waiting & Corridor at First Floor

Providing material and labour for fixing SS 316 grade push-pull pair of handle of size 600 mm long x 32 mm dia made out of satin (brush) finish hollow pipe of 1.5mm thick having offset type (C or D shape)/ H-shape/ D-shape of approved make with necessary screws etc. complete for wooden doors/ aluminium doors/ metal doors for all heights, all floors and all level as per approved sample and as directed by Engineer-in-charge. Rate shall be The length of handle should be perfect center to center as below specified.

Providing and Fixing 15 mm dia. CP brass extended lever handle pillar cock with ceramic disc cartridge for all laboratory sinks or as directed by the Engineer-in-charge, complete, making all necessary connections etc of approved make.

SITC of 2 compatement 100 mm x 50 mm wall trunking/race way with cover and all accessories made out of PVC .

Providing and arranging in position storage unit having Sliding door of VSDU-5 of Godrej or equivalent of approximate size 900mm x 450mm x 1200mm. Storage unit shall be made out of CRCA steel - D grade as per IS 513 having epoxy poyester powder coating of 50 microns. Storage unit shall be of knock down construction with adjustable self arangement and all required hardware i.e. handle, lock (5 lever), roller, ball bearing etc.

Providing material and labour for fixing 1 point panic device in Contur design on active leaf and 2 point modular on inactive leaf, carry bar for rebated double door of approved make for fire and smoke check doors, with steel latch, security anti thrust latch consisting of all required accessories in silver finish. As per EN 1125, CE marked with necessary fittings etc. complete for all floor all height as recommended by manufacturer and as directed by Engineer in Charge.

Supply & fixing of 200 pair MDF unit with required modules in a fabricated CRCA powder coated junction box of size 450x250x100 with two no. of pad-lock, provision for earthing.

Providing & fixing of Nitrile rubber closed cell (Thermo plastic elastomeric) insulation of the following diameter and thickness over hot water pipes and fittings, of minimum 45 kg / M³ density and haivng thermal conductivity 0.037W/MK or better at 20°C mean temperature, class 'O' insulation applied by suitable adhesive complete as per manufacturers specifications (for internal and external hot water supply) all complete as per directions of the Engineer-In-Charge. Rate includes cost of all materials including fixing the insulation with the pipes with tapes or adhesives, labour charges for working at all levels. leads and heights. e) For 50mm dia pipes - 25mm x 54mm Nitrile Rubber Plain Tubing

Supplying and erecting, testing and commissioning of 1x10W 600mm LED Surface Mounted indoor Linear smart Bright Battern Lights Fittings -Make Phillips or equilavent ( BN021)

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. BLOCK-B SECOND FLOOR HVAC PANEL As per Single line diagram

Providing, laying and jointing in true line and level 50mm diametre U.P.V.C (Type B) conforming to IS 13592 with one end plain and other end socketed with rubber ring, & fittings conforming to IS 14735 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials. Pipe length per piece: 1.8 Mtrs

Supply, installation, testing and commissioning of Butterfly valve (manual) with CI body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified: 150 mm dia.

Supplying mterial and labour for laying of following size DWC HDPE pipe of 63mm dia outer dia ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. direct in ground including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete for all depth as directed by Engineer in charge.

Providing and fixing full thread coupling on each tank for inlet and outlet connections of G.I. (medium duty) as per IS: 1239, including drilling holes in the tanks at required levels, inserting the coupling in place, sealing the hole with silicon sealant, attaching the hex nuts on either side of the coupling as directed and approved by the Engineer-in-charge. (A) 65mm diameter

Supply, Installation, Testing, Commissioning of Ultrasonic type Flow Meter

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing & Commissioning of Floor Mounted Air Handling Units as specified below; Double Skinned powder coated inner & outer skin of 0.6 mm & 43 mm thick, 40 kg / m3 PUF Sandwitched insulated aluminium sectionalized construction Comprising of Fan section with 50 mm static best efficiency Plug type Fan driven by suitable pole Eff - 1 TEFC Motor with Drive Package driven by IP55 / 4P TEFC Fan Motor / fire resistant flexible fan outlet connection, The AHU shall comprise filter section with Air filtering media with 10 micron pre filter, Cooling coil section with Chilled water Coil complete with Copper tube 13 FPI AL finned 4R deep chilled water cooling Coils, SS 304 condensate drain pan duly insulated with 15 mm thick cross linked polymer Nitrile rubber insulation, with Mixing box with Aluminium Aerofoil damper for supply, return & Fresh air, necessary vibration isolation arrangement by providing spring isolators ; Motor selection to suit the below capacity for each AHU rating by AC Vendor including transmission losses. ; Electrical Starter suitable for Respective AHUs, Panel supplied with matching rating for SA Fan motor, required DC Supply for control Valve, including short circuit / overload MCB protection, Motor Status On / Off / Trip, command, Automanual, Status contacts for remote operation through Operating Panels, Temperature Indicator availability on Panel with BAS compatiibility; Starter panel shall be minimum 14G MS powder coated with ventilation fan (only for VFD AHU Panels), inside light and duly internally wired and tested, Unit shall be supplied with Digital Thermostat with water proof casing BMS compatible with interface modbus / bacnet protocol to connect the BMS panel ; Prices to include dispatch of AHU in Semi-knocked down condition, assembly at site and lifting / shifting to actual locations as per layouts; Performance to be complied - common for below AHUs: dB=60 at 3 M distance; Price shall be complete with electrical Starters for each AHU matching the motor ratings and as specified above ; AHU dimensions, configuration (top discharge / side discharge), pipe connection side & door side shall be tailor made as per final layout and space constraints. No extra claim shall be payable for such customisation; Schedule below shows. 10.20 TR / 4450 CFM For Reception Waiting & Corridor at Second Floor

Providing, laying and jointing in true line and level 150 diametre U.P.V.C (Type A) conforming to IS 13592 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Providing material and labour for fixing factory made and pressed laminated 30mm thick flush door shutter of specificied thickness made of ISI marked non decorative type flush door shutters confirming to IS- 2202 (Part 1), core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers (IS 710 Grade) on both faces of shutters having 1 mm thick decorative type laminates of approved make, shade, finish on both faces of shutter fixed with phenol formaldehyde synthetic resin type adhesive conforming to IS 848 including providing and fixing external lipping with 2nd class teak wood battens, exposed (37mm x 12mm)/ concealed (35mm x 12mm) on all edges of door shutter as required with 2 coats of synthetic enamel painting including 1 coat of wood primer & lapi/ lacquer polishing with primer to all exposed side of lipping, all as per approved drawing, for all floor, all level all height etc. complete as directed by Engineer-in-charge. Measurement including lipping shall be considered for payment. Necessary hardware like hinges, pivot, handle, tower bolts, locks etc shall be separately measured and paid in the relevant tender items. Cost of laminates shall be paid in relevant tender item.

Supply, Installation, Testing and Commissioning of Gun Metal Air Release Valve with necessary fittings. Size: 25 mm (For Riser)

Dismentling steel work including distempering and stacking the materials with all lead and lift.

Supply, Developing, Testing, Commissioning of IP based 32 bit dual core microprocessor, minimum 128 MB RAM & 64 MB flash memory, true peer to peer communication,DDC to support NTP synchronization,DDC should be modular & expandable in steps for future expansion requirements, DDC with 230 VAC +_ 10 % powered will be preferrable , DDC shall have inbuilt web browser and support XML, along with DDC Panel for Water Tanks - as per IO Summary and as per technical specification etc. as required.

Supplying, installing, testing and commissioning of factory built Ceiling Suspended double skin type air handling units made of 25 mm thick panels consisting of G.I. casing of thickness 0.8 mm outside layer and 0.8mm inside layer with polyurethene foam (PUF) insulation having a density of 40 Kg / Cu M factory injected between them by injection moulding machine, complete with blower section with blower DIDW forward / backward curved centrifugal fan with 50 mm static, 4 row deep cooling coil section with aluminium finned copper tubes (tube thickness not less than 0.5mm), with Mixing box, filter section with MERV 6 pre filter for return & fresh air, Fine filter section with MERV 12 filter, belt with TEFC drive motor (Eff-1) suitable for 415+/-, 10% volts, 50 Hz, 3 phase, A.C. supply with starter panel, drain connections with drain valve, 2mm thick Stainless steel single sloping insulated drain pan (for zero water retention), Descaling valve, auto air purge valve, thermometers and pressure gauge at the inlet and outlet of coils, supplied with factory fitted matching size 2 way ON / OFF actuator type Brass / Control valve / Cu piping with required couplings and ends flanged to fit CHW In / Out piping, necessary vibration isolation arrangement, Supply air side canvass connection with damper etc, complete as per specifications. Price shall be complete with Electrical Starter Panel supplied with matching rating for SA Fan motor, required DC Supply for control Valve, including short circuit / overload MCB protection, Motor Status On / Off / Trip, Automanual Status, Temperature Indicator availability on Panel with BAS compatiibility; Starter panel shall be minimum 14G MS powder coated with ventilation fan and duly internally wired and tested. Followings are capacities. (With 5 Micron Filteration) 2.19 TR / 1300 CFM For Lab at First Floor

VALVES WITHOUT INSULATION Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 40mm dia.

Supply, Installation, Testing and Commissioning of integrated Audio source with the following features : Two single CD\USB\SD and DAB\FM line outputs can play music applications in two areas, The volumes of the two line outputs can be adjusted separately, CD\USB\SD has three play modes: single play, all play and repeated play, DAB\FM can preset 10 channels of programs, RS485 remote control interface as per technical specification etc. as required.

Providing material and labour for laying average 40 mm thick machine cut polished Green kota stone slab of size upto 0.9mt length with uniform thickness double side polished at edges for parapeet wall coping, window sills, over 20 mm (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry or stone fixing adhesive and mechanical fastner of approved make including rounding of exposed edges, polishing, rubbing, curing, finishing, buffing after final polishing, maintaining upto handling ovre the project etc complete as directed by engineer in charge. All Expose edges of stone shall be pencil sharped and in even thickness and polished at all floors any heights, any lead and lift etc complete. as directed by Engineer Incharge. Sample shall be approved before execution. Sample and mockup shall be approvd procurement of material.

Providing and arranging in position Cabinate unit beside bed with drawer and locker of Ayush of Godrej or equivalent. Overall dimension: (L)420 mm X ( W)400 mm X (H) 840 mm. Drawers and cabinate should be made of CRCA have thickness of 0.8mm and Slide should be made of MS with zinc plating & should be telescopic in nature. Top should be made of SS of grade 304 having thickness of 0.8mm. Plastic molded plastic castors with 50mm dia. Anti bacterial thermosetting epoxy polyester powder coating should done for all MS components.

Supply, Installation, Testing, Commissioning of Water Type Differential Pressure Switch

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Floor Heat recovery unit of 0.6mm thick Pre-Coated GI sheet Outer skin & 0.6 mm thick GI sheet metal cabinet type plain Inner skin Double skin unit with with 40 mm thick with Thermal break profile, 40 kg/cum polyurethane foam sandwiched between panels complete with pre filter of MERV -8 efficiency at fresh air inlet along with Gridblok IAQ chemical filter with turbulent flow and monolithic structure with 100 mm thick designed for 500 fpm with pressure drop not exceeding 146 pa having density 27.54 lb/ft of along with MERV-13 fine filter at fresh air outlet, MERV-8 filter at return air outlet. Fan section with direct driven plug fan & IE-3 Motor with, IP-21 variable frequency drive shall be suitable for 415 + 10% volts, 50 cycles, 3 phase AC supply. Heat reovery unti shall be wheel type of aluminium with 3 angstorn molecular sieve which is for recovery of both latest and sensible load. The unit shall have two separate passages one for supply of fresh air and the other for exhaust of cool air from the rooms after the recovery of energy, with all accessories as required. The fan outlet velocity shall be limited to 9.5 MPS maximum and face velocity across filter shall be limited to 500 FPM maximum. The unit wheel shall be min. 200 mm thick and shall be capable of recovering atleast 75% latent as well as sensible energy. The unit shall be complete as per drawings and specifications. The Photohydroionization cell with the capability to produce friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides Ions with quad metalic coating (Rohdium, silver, copper and titanimum) and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into the conditioned/ served space. The honeycomb matrix shall not be accepted. The units should be designed after undertaking a load factor calculation for each specific area where the equipment is to be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the units. The system shall be capable of reducing microbial bacteria, virus and spores , VoC’, odors and particulates matter. The equipment shall conform to UL 1598 CAN/CSA C222 EN60335-1, EN60335-2-65, EU standards, certifications shall be submitted along with the technical submital. Supply air fan - 2750 cfm, external static 50 mmwg Exhaust air fan - 1750 cfm, external static 50 mmwg

Supply, installation, testing and commissioning of Y Strainer of CI Body flanged ends with stainless steel strainer 304 having 1.2mm perforation complete with necessary accessories: 150 mm dia.

(c) 3.5C X 150 SQ. MM. AL XLPE CABLE

Sec.8.0 Waterproofing works Providing material and labour for laying average 18mm thick double coat (water proof) smooth/ wired finish cement plaster on sides of masonry work/ block wall/ RCC wall, 12 mm thk first coat in CM 1:3 (1 cement : 3 coarse sand) by spraying , second coat of 6 mm of CM 1:3 (1 cement : 3 fine sand) and mixing Integral waterproofing liquid admixture for mortar in recommended proportions in both coats, finishing the surface wired finish/ smooth finish with a floating coat of neat cement slurry at 2.75 Kg/ sqm to receive the tiles for all floors, all shapes and all height including hacking to RCC surface, scaffolding, curing etc. complete for all floor, all height as directed by engineer-in-charge. Cement slurry admixed with Integral waterproofing liquid admixture for mortar in recommended proportions is to be applied before each coat and final finishing coat.

Providing and fixing white vitreous china extended wall mounting water closet of size 790 x 370 x 690mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre / 6 litre (adjustable to 4 litre / 8 litre) including seat cover, and cistern fittings ,nuts, bolts, and gaslets etc complete.

Providing and fixing 8mm dia C.P. / S.S. jet with flexible tube up to 1 meter long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer-in-charge.

Supply, Installation, testing, commissioning of UL listed, BTL approved IP BASED Open protocol INTEGRATOR with Inbuilt web browser & with max 150 device capacity, multiprotocol supported & should be of the same make as the DDC : INTEGRATION OF FOLLOWING SYSTEMS ON MODBUS-rtu / BACNET: The corresponding mentioned third party vendor shall be responsible to provide serial converter [RS 485 to RS 232] and the BMS vendor to accommodate the software address required for integration. including all necessary mounting hardware and accessories. as per technical specification etc. as required. of software interface for ETPs (1 Nos.) Soft Data Integration on Modbus / RTU. as per technical specification etc. as required.

Tree plantation Supplying material and labour for planting of trees including termite treatment, and planting of plants in existing prepared tree pit or excavated pit. (height 4'-6' above bags/pots). Soil mounts 4”-6” in size. Tree plantation should be carried on neatly accurately and with perfection as per drawing and instruction given by the EIC. Plastic bags or pots should be removed carefully and soil around the roots should not be dropped or disturbed much. Bill shall be placed after completion of maintenance period but not before stabilizing the hedges. Rates for mortality to be inclusive. Providing and fixing tripod made of wooden balli, height 1.50mtr. Top bracket to be 300mm x 300mm. leg embedded in ground up to 300mm and to have tar coat. Work shall be done as shown in the drawing or as directed and approved by EIC. Excavation and soil filling shall be paid in relevant tender item.

Providing and arranging in position Fabric finish visitor chair of Barvo of Godrej or equivalent with approved shade of fabric. The seat and back shall be made up of 12mm thick hot-pressed plywood and upholstered with fabric upholstery covers and moulded polyurethane foam. The one-piece armrests should be injection moulded from black co-polymer polypropylen. Chair hvae cantilever type MS EWR tubular frameas legs having powder coating (dft 40-60 microns).

CONDENSER WATER PIPE Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS ‘C’ class along with necessary clamps, vibration isolators and fittings such as bends,tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 150 mm dia.

Providing material and labour for Extra charges for machined Perforation of required dia and pattern in flush door shutter/ compact sheet of any thickness for air circulation for all floor, all height all level as per drawing and as directed by Engineer in charge. Edges of perforation shall be finished and sharpen.

Providing and fixing Gun metal gate valve with C.I. wheel of approved quality (screwed end). (d) 40mm dia nominal bore.

Supplying and erecting, testing and commissioning of 40W LED batten Surface Mounted Industrail Corroson proof Fixture Ip 65 -Make Crompton or equilavent (IPFC112LT8-16 2X 20W)

Providing material and labour for fixing of SS 304 grade satin finish lever action Flush tower bolt with 19mm projecting bolt (extended rod of 600mm length) aluminum casted of approved make for double shutters aluminum door, with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Providing and arranging in position FOLDING WHEELCHAIR WITH CUSHION of Godrej or equivalent. Overall dimension (L) 790 x (W) 600 x (H) 870mm. Foldable frame structure should be made of section 22x1.2mm A3 carbon steel with chrome finish. Cross bar should be made of A3 carbon steel with section 25.4 x 1.2mm. rear wheels should be 24 inch Solid mag wheels with alloy in the rim. Integrated handrim provide to drive the wheel chair of section 16x1.2mm A3 carbon steel with chrome finish. front wheel should be 8 inch HUB made of PA polymer and outer with solid rubber. PU molded arm rest & base should be made of ABS for better arm support. Leatherite strap should be available as for calf rest & seat of wheelchair should be made of leatherite cushion Adjustable foot rest with alluminimum die cast foot rest with updown & swivel type mechanism. Hand brakes should be provided to lock the wheelchair at desired location. Extended base with molded plastic for better grip. Anti rust chrome finsh. The manufacturer should compilant with ISO 9001, 14001, OHSAS 1800 and CE certification.

Supply, Installation, Testing and Commissioning of Patient Handset The module will be connected with Bedside module with Intelifix connection features. The handset should have call button with Nurse sysmbol, membrane keypad with call button. optional Room or reading light control, 2.8 m cord. Handset must have antimicrobial coating on the surface and confirms to VDE 0834.

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Thickness 1.25 mm sheet

Providing material and labour for fixing adjustable/ fixed Teflon roller bearing set with reinforced nylon casing of approved make (twin or single wheel according to weight and size) for sliding window/door as per drawing etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Supply, Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. 60KVA UPS 3 ph in 3 ph out for balance load

Supply, installation, testing and commissioning of cabinet type Floor Mounted / Loft Mounted Type single skinned Centrifugal Exhuast Air Unit; unit shall have leakproof canvass connection along with damper at suction side & descharge side cowl; ready to start unit hooked upwith 4P TEFC with IP 55 protection motor with pully / belt drive arrangement on adjustable frame; fan motor assembly mounted on corrossion proof-painted MS baseframe; baseframe to rest on vibration isolation pads. The unit shall be supplied with Starter Panel of required motor capacity. 3200 CFM / 40mm Static Pressure for O.T Store

Extra for additional height of propping and centering where the height of propping and centering exceeds 4.0 mt. Between supporting floor two ceiling including temporary brick or stone pillars for supporting as required. (I) Height more than 4.0 mt & upto 9.0 mt.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Providing material and labour for fixing SS 304 brush finish solid Door Stopper with magnet, fixed type, wall mounted (square/ round) of approved make with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Providing material and labour for making tree pit with 800mm diameter NP2 class hume pipe with 600 mm height to be placed on the filled garden soil and outside area of the hume pipe to be filled with the good quality earth. Hume pipe shall be filled with the mixture of garden soil, farm yard manure and required pesticides etc. complete as directed by Engineer in charge. Excavation and soil filling shall be paid in relevant tender item.

INSULATED VALVES Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 50mm dia.

CONDENSER WATER PIPE Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS ‘C’ class along with necessary clamps, vibration isolators and fittings such as bends,tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 100 mm dia.

Sheet steel metal enclouser for FP MCB equivalent to Legrand cat No...607884

Supplying, installation, testing & commissioning of central graphical fire alarm management system to centrally monitor and operate the fire alarm system complete as required.

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Ceiling Suspended Chilled Water Fan Coil Units as specified below with; Single Skin Fan Coil Units in standard construction with Fan section with DIDW multi blowers & energy saving Single Phase BLDC motor/ EC Motor (Electronically Commuted Motor), Filter section with prefilters, Hydrophilic Al type Copper Coil section with minimum 3 Rows and minimum 13 FPI Chilled / Hot Water Cooling Coil, pre-assembled valve station with set of brass ball valve with "Y" strainer set, Insulated extended L shaped Drain Pan, supplied with pre-calibrated matching size 2 way / Pressure independent modulating cum balancing valve of minimum PN25 rating with P/T plugs and minimum IP54 t electrothermic / motoric modular actuator (0 to 10 Volt DC Signal), fixed on FCU Cu piping with required couplings and ends flanged to fit CHW field In / Out piping and its compatible 24VAC control transformer; All valve assemblies are to be insulated with closed cell elastomeric nitrile rubber insulation. UNit shall be supplied with Digital Fan Coil Thermostat with Fibre water proof casing BMS compatible with interface modbus protocol to connect the DDC panel (230V operating / Power On / Off provision, 3 speed fan switch & Temp Edit facility / Digital Temp Display) and supplied with 10 RMT cable from Controller to FCU as required. The Performance of units should be certified by a reputed third party agency and available for witness testing facility at manufacturer's factory. 600 CFM

Providing & Fixing M/F Suspended 12.5mm Plain Gypsum Board which includes GI Perimeter Channel is fixed along the perimeter of existing wall/ partition with the help of screws at 600mm centres. GI Ceiling Angle is suspended at up to suitable height as per sight conditions by fixing it to the GI soffit clit with Soffit Cleat and  Rawl Plug creating 1220mm x 1220mm grid. GI Intermediate channel is fixed to the GI Ceiling Angle with 2 Nos of 4.2x13 GI metal to metal screw. The GI Ceiling Section is then fixed to the GI Intermediate Channel with the help of  Connecting Clip and in direction perpendicular to the Intermediate channel at 457mm c/c. All framing and grid section shall be GI (as per IS 513) having yeild strength 300 mpa and galvanized finish of 150 GSM as per IS 277. Single layer of 12.5mm tapered edge Plain Gypsum Board (Confirming to IS 2095-Part-I, 2011) is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Jointing Compound & Joint Paper tape. The contractor should prepare shop drawings based on the concept drawing and get it approved by the Engineer-in-charge. After approval of drawings, the contractor shall prepare the sample based on the drawing and get it approved by the Engineer-in-Charge before execution. Rates shall be inclusive of cost of making cut outs/ openings for electrical fixtures, tube lights/ air-conditioners, grills, diffusers etc & providing additional sections for strengthening the openings/ cutouts, making grooves between wall & board or as per drawing for all floor, all level, all height etc as directed by Engineer in charge. Area of cutouts shall not be deducted and no extra payment shall be considered for additional sections provided. Only plan area shall be considered for payment.

Supplying, Splicing , testing and commissioning of LC type single mode pre-terminated pigtail 1mtr as per tender specification etc. as per technical specification etc. as required.

Sec.4.0 Condenser Water Piping CONDENSER WATER PIPE Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS ‘C’ class along with necessary clamps, vibration isolators and fittings such as bends,tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 300 mm dia.

Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Aluminum Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 35 Sq.mm x 3.5C Al. Cable

300 x 105 mm

Providing and fixing Channel for optimizer of of required length as per unit. Guide channels shall consist of 'J' section 2 mm thick & 25 mm square bright bar - both connected by screws. Prior to the embedding of the guide channels with the help of raul plug & screw, the ground has to be in proper leveled condition. Guide channel shall be of same make as optiimizer and as per manufacturer's specification.

Loop light point to be controlled from same switch.(Looping from first point)

Secondary Variable Chilled Water Pumping System with VFD including Supply, Installation, Alignment, Testing and Commissioning of End Suction Top discharge Back Pull out Centrifugal type Secondary Chilled water pumps as specified. The pump shall be dynamically balanced and supplied with Flexible coupling with Guard, Corrossion resistant painted MS factory supplied baseframe with necessary vibration isolators and Rubber flexible bellows at suction and discharge nozzels; Entire System including Pump, Controller and related controls shall be procured from single pump manufacturer; Design shall comply to secondary fundamentals briefly described in the tender and further as recommended by manufacturer for intended system performance; Electrical Control Panel capable of cyclic operation of pumps - Controller shall be capable of controlling upto 3 Pumps in parallel housed in IP55 Control Panel compatible for interface with Pump Starter Panel and Variable frequency drive panel - duly internally wired and tested - parallel pumping software downloaded; Controller shall support either of BACNet / Lon / MODBUS protocols only; Variable Frequency Drive rating shall match the Secondary Pump Motor rating; all drives shall be installed in single VFD panel provided with ByPass arrangement - with entire assembly duly internally wired & tested; each VFD shall be provided with dedicated Isolator and included in the scope; Supply, installation, testing and commissioning of Differential Water Pressure Transmitters supplied and installed across selected AHU loads in the field and wired upto Pump Logic controller for integrated operation of the variable speed pumping system - cost to include supply and laying of 3C*1.5 sq mm armored signal cable upto Logic Controller. 700 GPM / 35 M WC (2 working + 1 stand by) Complete job as per technical specifications etc. as required.

SITC of Approved make Ceiling fan with double ball bearing ISI mark with condenser A.C. 230 V. 50 Cys. 900 mm. sweep complete, canopy and 30 cms. down rod erected on existing hook or clamp with 24/0.2, 3 core flexible wire with earthing

Providing and arranging in position leatherette finish High back chair of Marvel of Godrej or equivalent. The seat and back shall be made up of Injection molded Plastic outer & inner and PU foam and MS ERW tube and upholstered with Leatherette. The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable. Chair shall be of 360° revolving type, upright-position locking, tilt tension adjustment with front pivot, seat/ back tilting ratio of 1:2, pneumatic height adjustment, High Pressure Die cast polished Aluminium pedestal and fitted with 5 nos. twin wheel castors.

One 6 A x 5 pin 250 Volt universal socket outlet point controlled by one 6 A switch located on switch board.

Supply, installation, testing and commissioning UL listed Quartzoid Bulb type Sprinkler Heads. (Standard Response): Pendent sprinkler with rosette plate 68°C

Providing and arranging in position Fabric finish stackable chair with Desklet & Arms of Scintilla of Godrej or equivalent. Seat and back shall be made of 12mm plywood upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. Frame structure shall be made of powder coated finished MS ERW tubes legs with castores. The full desklet assembly should be flip-up type and should be made up of MS ERW tube and on which an scratch resistant tant abs desklet top.

Providing and arranging in position 2 seater gang seating for visitors of Nano of Godrej or equivalent of sapproximate size 1100mm (L) x 570mm (D)x 400mm seat height and 650mm total height. Gang seater shall be made of powder coated MS ERW tube, chrome plated made of cold rolled steel, powder-coated perforated shell, chrome plated solid steel for differant elements.

Providing material and labour for injecting Chemical emulsion for PRE - CONSTRUCTIONAL anti-termite treatment and creating a chemical barrier on the top surface of plinth filling, inside junction of wall and floor, on top of damp proof course (DPC) or on masonry at level of plinth filling as per IS 6313 (Part-2)-1981 using chemical like chloropyripos emulsifiable, Biflex TC, lindane (IS 8944-1978) 20EC mixed with water in 1:19 ratio (1 liter chemical : 19 liters of water). The emulsion shall mentioned below, all as per specification and directions of Engineer-in-charge. Plinth area in plan at GF shall only be measured (for akk below specified steps) and paid. A guarantee bond of 10 years shall be furnished. A1) Bottom surface and the sides of the excavation made for masonry foundations at the rate of 4 liters/sqm (wherever applicable) A2) At the rate of 7.5 liter/ sqm to the backfill at the depth of 500mm below the original ground level. The soil in the immediate contact with the vertical surface of RCC column/ Masonry shall be treated. B) Top surface of the plinth filling including damp proof courses at the rate of 5 liter/sqm of internal plinth area etc. complete. C) At the rate of 7.5 liter/ sqm to the internal vertical surface from original Ground level to top of the earth filled in the plinth. D) At the rate of 7.5 liter/ sqm to the external vertical surface below finished Ground level to the full depth of the filling complete. E) 1 liter / linear meter along the junction of wall and floor at all stages.

Supply, Installation, Testing and Commissioning of Call / Cancel button The module should consist of finder / reassurance light with membrane keypad includes call button with Nurse symbol, cancel button (green). The button must have antimicrobial coating on surface and confims to VDE 0834.

Providing material and labour for laying Plain cement concrete 1:3:6 (1- Cement : 3- Coarse sand : 6- crushed stone aggregates 20 mm nominal size) in Foundation and Plinth including cost of formwork, compacting, finishing, curing etc complete for all level, all height/ depth as directed by engineer in charge.

Supply, Installation, testing and commissioning of hot dip GI perforated type cable tray with all accessories like coupler, GI nut bolts,bend, tee, reduser etc as per specification and drawings complete with all required hardware : 150 x 100 made out of 2 mm thick perforated type

Supply & Installation at fixing of resing bonded slab & with company bonded black glass tissue faced for False Ceiling Insulation as per detail specifications - 50mm

Providing following type of Modular Type Accessories mounted with pvc / metallic box covered with appropriate front plate modules erected with necessary connection. As desired by Engineer In charge. (8) Modem Jack for Computer Open RJ-45.

INSULATED VALVES Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. 250mm dia.

Providing material and labour for placing in position 80 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100mm c/c on both ways , neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick , 100 mm wide MS sheet duly painted over priming coat , reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc i/c cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge.

Ceiling Hanging Providng and fixing of Modular Signages using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. Internal graphics to be made of 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty. Sign panel shall be finished with anti-reflex cover 1mm thick with one side Matt and other side Glossy finish. Polypropylene (PP) End caps which can be fixed to the extrusion with the help of screws. Panels shall be clicked on to the end caps. Aluminium framing shall be suspended from ceiling with suspension clips and cable (SS 304) with adjustable arrangement and signage panel shall be laid on aluminium framing as per manufacturer's specification. Rate shall be inclusive of total modular signage system for all level, all height etc complete as directed by engineer in charge. Sampe shall be approved before execution and mockup shall be done with approved sample for 2 to 3 number of signage.

450 x 105 mm

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Ceiling suspended Chilled Water Cassettes, 4 way flow type Fan Coil Units with energy saving Single Phase BLDC motor / EC Motor (Electronically Commuted Motor), Filter section with prefilters 70% down to 20 micron, Hydrophilic Al fins and Copper Chilled Water Cooling Coil section with minimum 2 Row and minimum 13 FPI, in-built condensate drain pump, pre-assembled valve station with set of brass ball valve with "Y" strainer set, Insulated extended L shaped Drain Pan, supplied with pre-calibrated matching size 2 way / Pressure independent control cum balancing valve of minimum PN25 rating with P/T plugs and minimum IP54 electrothermic / motoric modular actuator (0 to 10 Volt DC Signal) fixed on FCU Cu piping with required couplings and ends flanged to fit CHW field In / Out piping; All valve assemblies are to be insulated with closed cell elastomeric nitrile rubber insulation. Unit shall be supplied with BMS compatible Digital Group Controller, necessary Networking Adapters and Gateway with interface modbus protocol to connect the DDC panel (230V operating / Power On / Off provision, 3 speed fan switch & Temp Edit facility / Digital Temp Display) and supplied with 10 RMT cable from Controller to FCU as required.The Performance of units should be certified by a reputed third party agency and available for witness testing facility at manufacturer's factory. 500 CFM

Providing material and labour for fixing powder coated inbuilt flush handle (without lock) of approved make of required capacity including all required accessories like nib, counter plate etc as per approved manufacturer recomendatation for aluminium sliding window with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

INSULATED CHILLED WATER PIPING Insulation (Exposed to Atmosphere Closed Cell Nitrile Rubber GC bonded and above it 2 layers of UV paint). Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 °C mean temperature class ‘O’ insulation Closed Cell Nitrile Rubber GC bonded applied by suitable adhesive and above it 2 layers of UV paint shall be applied , over and above glass cloth to be applied, complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 50 mm dia.(32 mm thick insulation)

Fix Louvers and Fins (made out of Aluminium Section) Providing, fixing, designing aluminium fixed louver of any type of louver section of approved make having minimum 50 micron polyster powder coating on all the surfaces of approved shade, texture & make as per manufacturer's specifications. Contractor shall submit the shop drawing for louver/ fins based on concept design/ drawing and as per elevation. Aluminium louver section shall be fixed on aluminium framing/ carrier/ panel/ GI clip and necessary sub structure with required fastners, hardware as per approved shop drawing etc complete for all floor, all height including scaffolding as directed by engineer in charge. Louver, framing and sub structure shall be in proper line, level and plumb. Necessary MS work shall be paid in relevant tender item.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. as per technical specification etc. as required.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Ceiling Suspended Chilled Water Fan Coil Units as specified below with; Single Skin Fan Coil Units in standard construction with Fan section with DIDW multi blowers & energy saving Single Phase BLDC motor/ EC Motor (Electronically Commuted Motor), Filter section with prefilters, Hydrophilic Al type Copper Coil section with minimum 3 Rows and minimum 13 FPI Chilled / Hot Water Cooling Coil, pre-assembled valve station with set of brass ball valve with "Y" strainer set, Insulated extended L shaped Drain Pan, supplied with pre-calibrated matching size 2 way / Pressure independent modulating cum balancing valve of minimum PN25 rating with P/T plugs and minimum IP54 t electrothermic / motoric modular actuator (0 to 10 Volt DC Signal), fixed on FCU Cu piping with required couplings and ends flanged to fit CHW field In / Out piping and its compatible 24VAC control transformer; All valve assemblies are to be insulated with closed cell elastomeric nitrile rubber insulation. UNit shall be supplied with Digital Fan Coil Thermostat with Fibre water proof casing BMS compatible with interface modbus protocol to connect the DDC panel (230V operating / Power On / Off provision, 3 speed fan switch & Temp Edit facility / Digital Temp Display) and supplied with 10 RMT cable from Controller to FCU as required. The Performance of units should be certified by a reputed third party agency and available for witness testing facility at manufacturer's factory. 500 CFM

Providing and arranging in position Blood bank chair and make connection with required service. Chair shall be as per approved sample.

01-CIVIL WORKS Sec.1.0 Earth work Providing material and labour, machinery for Excavation of foundation upto 1.5 m depth including sorting out and stacking of useful materials and disposing off the excavated stuff with in the campus for all lead, all lift/ depth and back filling foundations, the trenches, plot filling, plinth filling with excavted material (excluding hard rock and black cotton soil) anywhere from the site/ campus etc complete as directed by Engineer in charge. - Any type of soil or rock not requiring Blasting.

Supply, installation, testing and commissioning of cabinet type Floor Mounted / Loft Mounted Type single skinned Centrifugal Exhuast Air Unit; unit shall have leakproof canvass connection along with damper at suction side & descharge side cowl; ready to start unit hooked upwith 4P TEFC with IP 55 protection motor with pully / belt drive arrangement on adjustable frame; fan motor assembly mounted on corrossion proof-painted MS baseframe; baseframe to rest on vibration isolation pads. The unit shall be supplied with Starter Panel of required motor capacity. 13100 CFM / 40mm Static Pressure for Washing, Drying & Press

Data Networking - Fiber Optic Cable and Components Supplying, installation, testing and commissioning of outdoor 12 core armoured single mode fiber optic cable for outdoor connectivity where ever required in prelaid conduits / RCC hume pipes/HDPE/DWC, whichever maybe available etc. as per technical specification etc. as required.

CONDENSER WATER PIPE Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS ‘C’ class along with necessary clamps, vibration isolators and fittings such as bends,tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 50 mm dia.

Providing and fixing bubble seal gasket of reddiplex, lorient or equivalent for door of any material made out of 5mm thick silicon having self adhesive fixing arrangement of approved shade and colour etc complete as per approved sample and as directed by engineer In charge.

Providing, fixing, testing & commissioning UL listed SS corrugated braided Flexible pipe, nominal Inlet by outlet 1"x ½" with required accessories to complete the installation: Size: 1000mm

Providing & fixing of Nitrile rubber closed cell (Thermo plastic elastomeric) insulation of the following diameter and thickness over hot water pipes and fittings, of minimum 45 kg / M³ density and haivng thermal conductivity 0.037W/MK or better at 20°C mean temperature, class 'O' insulation applied by suitable adhesive complete as per manufacturers specifications (for internal and external hot water supply) all complete as per directions of the Engineer-In-Charge. Rate includes cost of all materials including fixing the insulation with the pipes with tapes or adhesives, labour charges for working at all levels. leads and heights. f) For 65mm dia pipes - 25mm x 76mm Nitrile Rubber Plain Tubing

Providing material and labour for laying 8 to 10mm thick, double charged Vitrified tiles of size upto 600mm (of any shade glossy, matt or satin finsh) of approved make, shade and finish as approved by Architect/ EIC for all floors/ any height/ any levels etc in wall tile, dado, risers of steps, jambs as per drawings. Wall tile is to be fixed over 10 to 12 mm thick smooth finish plaster in cement mortar 1:3 (1 cement : 3 coarse sand) and fixed with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including provision of groove, grouting of joints, finishing of joints, curing etc complete for all floors any heights, any lead and lift as directed by Engineer In charge. Grouting and backing coat plaster shall be paid in relevant tender item. Sample and mockup shall be approvd procurement of material.

One light point controlled by two, two way 6 A switch

TYPE-3 Supplying, installation, testing and commissioning of Layer 2 Fully manageable networking switch, 24 # 10/100/1000Tx ports, minimum 2 SFP+ ports as per technical specification etc. as required.

Providing material and labour for laying 20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) with necessary scaffolding, curing, finishing, making grooves, forming pattas, hacking properly to RCC surface etc. complete as directed by the Engineer-in-charge.

Providing & fixing C.P. Bath Spout with all nuts, washer complete as per of approved Quality and conforming to Manufacturers Standards. Work to be completed to the satisfaction of the Engineer-In-Charge. Make: Jaquar-FLR-SPJ-CHR-5429G or Equivalent of the same make.

Wooden veneer ceiling Providing and fixing ply + veneer false ceiling on GI framing system for false ceiling work as per drawing and as following. 1) GL framing system which includes Perimeter Channel is fixed along the perimeter of existing wall/ partition with the help of screws at 600mm centers. Ceiling Angle is suspended at up to suitable height as per site conditions by fixing it to the soffit Cleat and Rawl Plug to creating grid. Intermediate channel is fixed to the Ceiling Angle with 2 Nos of 4.2x13 metal to metal screw. The Ceiling Section is then fixed to the Intermediate Channel with the help of Connecting Clip and in direction perpendicular to the Intermediate channel. All framing materials shall be of GI (IS513), YS-300Mpa, Finish-Galvanized 150GSM (IS 277). 2) 12mm backing play wood shall be 303 BWR grade of approved make shall be fixed on both side of MS framing of false ceiling work with SS screws. 3) 4mm thick teak veneer shall be fixed on ply with adhesive, hardware etc complete. 4) Wooden Beading shall be applied on all the sides of the panels of required size. 5) All exposed surface of wooden shall be lacquer polished of approved make, shade and texture. Actual area of veneer surface shall be measured and paid in sqmt without considering any wastage. Contractor shall get the sample of all material approved by Architect/ Engineer-in-charge.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: 17.7.2 White Vitreous China Wash Basin size 630x450 mm with a single 15mm C.P. brass pillar tap

Sec.11.0 Painting works White washing with lime on wall and ceiling surface (two coats) to give an even shade including thoroughly booming the surface to remove all dirt, dust; mortar drops and other foreign matter etc complete for all floors, all heights, all level as directed by Engineer Incharge.

Sec.2.0 Sanitary Installations Providing & fixing Divyang toilet set with European Closet (P Trap) & wall mount wash basin & all divyang requirements with dual flush tank, seat & cover (heavy duty) with C.P. brass hinges,including WC connector of 110mm inlet x 110mm outlet, connecting the same with soil pipe using appropriate solvent cement, C.I. Brackets for wall mounting the basin, 32mm CP waste Coupling, 32mm size CP bottle trap, CP brass Spatula Faucet, etc. all Internal fittings complete with S.S grab rails etc. rubber buffers, C.P nuts, bolts etc making holes in walls & floors, & finishing for ready to use.The rate includes all necessary connection charges as per product detail to the satisfaction and as directed by the Engineer-in-charge.

INSULATED CHILLED WATER PIPING Insulation (Closed Cell Nitrile Rubber GC bonded 2 layers of paint). Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 °C mean temperature class ‘O’ insulation Closed Cell Nitrile Rubber GC bonded applied by suitable adhesive and, over and above glass cloth to be applied, complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 40 mm dia.(32 mm thick insulation)

Providing material and labour for fixing 6mm thick Clear Toughen Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.

Providing material and labour for Fixing of Mineral Fibre Suspended Ceiling System with Bevelled Tegular edge hygienic tile with grove (Bioguard) with 15mm Exposed grid. The tiles should have Humidity Resistance (RH) of 95%, Light Reflectance 90%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0/Class 1 (BS 476 Part 6 & 7), in module size of 600x600 x minimum 15mm with Anti Microbial coating on the face of the tile. The tile shall be laid on any type of grid system (Silhouette/ superfine/ select grid system of Armstrong) with 15mm white flanges incorporating a 6mm central reveal in white/ black colour and with a web height of 45mm and a load carrying capacity of minimum 15.68 Kgs/M2 & minimum pull out strength of 100 kgs. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with suspension system of same make. INSTALLATION: To comprise main runner spaced at 1200mm centres securely fixed to the structural soffit using Armstrong suspension system (specifications below) at 1200mm maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres. SUSPENSION SYSTEM accessories shall be of same make and consisting of M6 Anchor Fasteners with Vertical Hangers made of Galvanised steel of size 26 x 26 x 25 x 1.2mm with a Galvanised Thickness of 80gsm, A pre Straightened Hanger wire of dia – 2.5 mm of 1.8 m length, thickness of 80gsm and a tensile strength of 344-413 MPa, along with Adjustable hook clips of 0.8mm thick, galvanised spring steel for 2.68 mm with a minimum pull strength of 110 kg. The adjustable clip also consists of a 3.5 mm aquiline wire to be used with the main runner.Contractor shall provide 0 year warranty against Tile & Grid system used together. Installation shall be done by approved applicatior of manufacturer all floors/ all heights/ all levels including scaffolding etc as directed by Engineer in charge.

Providing and arranging in position cafe chair of UNWIND of Godrej or equivalent. Chair shall be made of MS Powder Coated (50 micron) Understructure (Without Arms) and the seat and back are made of injection moulded high impact strenght polypropylene polymer compound with indoor graade UV Resistance. The Shoes are made of high impact strenght polypropylene polymer compond with indoor grad UV Resistance and pressed fitted with tubular fram. Approximate size of chair is 520mm (W) x 550 mm (D) x 850mm & 450mm (H).

150 x 105 mm

Providing & Erecting approved make following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper insulated with Foam PE & Secondary conductor made of poly – Aluminium film bonded Al. Braids @ suitable coverage overall sheathed with black PVC insulation. (b) RG – 6.

Providing material and labour for fixing set of dead lock of approved make with 50mm backseat, 20mm square for end with 72 mm centers including strike plate in satin stainless steel finish as per DIN 18251-1, grade 2 and prepared for euro profile cylinder (EPC) including strike plate and EPC length 60/70 mm standard Euro profile Pin Cylinder/ Half pin cylinder with both side key/ one side key one side knob operation with one pair of SS 316 grade Escutcheons (key hole plate) for wooden/ aluminium/ metal doors with necessary SS Phillips head screws etc complete for all floor, all level, all height as per approved sample and as directed by engineer in charge. The lock shall be with 3 keys.

Providing and fixing C.P. brass Wall Mixer with provision For overhead shower with 115mm Long Bend pipe on upper side, connecting legs & wall flanges, complete as per approved make and as directed by the Engineer-in-charge.

Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs & wrapped with FR PVC tape & sheathed with FR PVC or HFFR outer jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos. of pairs. With necessary connections. A Conductor Size 0.5 mm. (b) Armoured. (Jelly Filled) (4) One Hundred Pairs.

Supplying and laying following sizes PVC pipe of approved make including excavation of trenches, laying the pipe as per layout and drawing and re-filling the trenches etc. complete as directed. Heavy gauge pipe in Open / Concealed manner minimum 40 mm dia.

Curtin in ICU Providing and fixing Cubical track system made of Aluminium Alloy of Box Size 1.7 x 20 x 25 mm with 50-60 microns thick powder coating in white color finish. Tracks are bendable to a radius of 250 mm at 90 degree to cover the whole bed. Aluminium track section shall be rigid high grade and with free – running roller wheel (not slides) and curtain hooks.

Earth wire/strips : Supply and laying cu. earthing required size strips for interconnecting the earthing stations, panels, DB's etc. in built up trenches, on walls/ceiling, buried in ground generally as specified and shown on drawings complete with : a) Fixing accessories. b) Corrosion protection of buried conductors with bituminous coating and covered with PVC tapes. 25 x 3 mm/ 32X6mm / 50x6mm CU. strip/ 38x6 Cu earth link

Supplying, assembling, grouting, levelling, installation, Connecting testing and commissioning of D.B of specified make but without MCB / ELMCB/MCCB etc but with all internal busbar as per requirement. Supplying, erecting, testing and commissioning of only TPN D.B. with space for FPMCB as incoming and space for DPELMCB and 4 SPMCB as outgoing per phase (i.e. 8 way TPN D.B.) with 8 way PPI kit

Providing and placing in position Examination couch of average size (L)1976 mm X (W)560 mm X (H) 810mm of Revive of Godrej or equivalent with following specification - 1) Base frame - ERW tube as per IS - 7138 - avarage size - 30mm x 30mm x 1.6 mm 2) 3 No bottom cabinate with 3 drawer at top line. Cabinate are made out of 1.0 mm thick CRCA sheet with recessed plastic handle, lock and door latch. Drawers are made out of 1.0 mm thick CRCA sheet with recessed plastic handle and double extention ball slide. 3) 12mm thick mattress integrated with top platform with adujestable head rest upto 30° angle and made out of integrated PU form upholstered with leatherite and strenthen with ply at bottom of platform. 4) SS 304 grade tissue roll holder provision. 5) Leveler - provide at base to compansate the un-even flooring made out of plastic with metal insert. 6) Inbuilt step stool/ Foot step - made out of 1.0 mm thick CRCA sheet with recessed plastic handle and can be slide In and Out on the ball slide for the use. 7) BP Aparatus Holder Tray with adjustable knob - 1.0 mm thick CRCA shaeet. All metal work shall be finished with Anti Microbial and epoxy polyster powder coating of white colour as per RAL shade.

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. BLOCK-B GROUND FLOOR HVAC PANEL As per Single line diagram

Providing and mixing Migratory Corrosion Admixture POLYALK CP 293 having Specific Gravity 1.01 to 1.04, pH value (Minimum 9.50) shall be alkaline in nature and having bipolar concrete penetrating corrosion inhibiting properties, inhabitor shall be non-nitrite based & have the ability to provide corrosion protection to both anodic and cathodic sites on the steel surface, inhibitor-steel complex shall formed polydentate complexes, having more than one bond with steel per molecule of inhibitor, with steel surface to promote proper film formation with enhenced bond to steel, inhibiting the electro-chemical corrosion reaction, inhibitor shall not have any adverse effect on concrete compressive strength, inhibitor shall have a corrosion rate of zero coulombs per ASTM-G109-2005, admixture shall be conforming to IS 9103 and in liquid form at the rate of 3Kg per one cubic meter volume of concrete admixture shall be added to the water, during mixing of cement, sand & aggregates and at the same rate admixture shall be added in case of Ready Mix Concrete at plant site, mixing of admixture during mixing of cement, sand and aggregates OR at work site the admixture shall be added in Concrete Transit Mixer before pumping / placing of concrete etc. complete.

63 A DP ELCB (30mA)

Supply, Developing, Testing, Commissioning of IP based 32 bit dual core microprocessor, minimum 128 MB RAM & 64 MB flash memory, true peer to peer communication,DDC to support NTP synchronization,DDC should be modular & expandable in steps for future expansion requirements, DDC with 230 VAC +_ 10 % powered will be preferrable , DDC shall have inbuilt web browser and support XML, along with DDC Panel for Fire Fighting Ststem - as per IO Summary and as per technical specification etc. as required.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Supply, Installation, Testing and Commissioning of Pull cord, The Module should consist of finder / reassurance light with 2 mters pull cord with the grip and nurse symbol on it, with mounting frame for srew free installation.

6/16A x 250 Volt switched socket outlet point for AC with 4 sq.mm wire for phase and neutral & 2.5 sq.mm earth wire.

LEVEL SENSORS: Supplying & erecting approved make Automatic liquid level controller 6A.as per instruction of Engineer in charge on site complete with wiring connection with existing wires , with copper conductor from pump to upper and lower tank.

CONDENSER WATER PIPE Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS ‘C’ class along with necessary clamps, vibration isolators and fittings such as bends,tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 65 mm dia.

Floor Directory Signage Providng and fixing of Modular Signages (removable) using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. For Flat panels, plotter cut vinyl letters to pasted and for sliding profile print to be made of 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty. Sign panel shall be finished with anti-reflex cover 1mm thick with one side Matt and other side Glossy finish. Polypropylene (PP) End caps which can be fixed to the extrusion with the help of screws. Panels shall be clicked on to the end caps. Aluminium framing shall be fixed on surface with SS 304 screw and signage pabnel shall be laid on aluminium framing as per manufacturer's specification. Rate shall be inclusive of total modular signage system for all level, all height etc complete as directed by engineer in charge. Sampe shall be approved before execution and mockup shall be done with approved sample for 2 to 3 number of signage. (Measurement : Actual area for directory signage shall be considered for payment.)

Supplying, installation, testing and commissioning of 10G SFP+ Single mode transceiver, 1310nm, 2Km, LC connector, inclusive of any hardware such as modules for populating SM-LC transceivers as per technical specification etc. as required.

Supply, Installation, testing, commissioning of UL listed, BTL approved IP BASED Open protocol INTEGRATOR with Inbuilt web browser & with max 150 device capacity, multiprotocol supported & should be of the same make as the DDC : INTEGRATION OF FOLLOWING SYSTEMS ON MODBUS-rtu / BACNET: The corresponding mentioned third party vendor shall be responsible to provide serial converter [RS 485 to RS 232] and the BMS vendor to accommodate the software address required for integration. including all necessary mounting hardware and accessories. as per technical specification etc. as required. software interface for UPS's (06 Nos.) Soft Data Integration on Modbus / RTU. as per technical specification etc. as required.

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. BLOCK-B UPS POWER OUTGOING PANEL As per Single line diagram

SITC of 40 A FP MCB

Garden Soil Filling Providing material and labour for Filling mixture of good quality garden soil obtained from outside for all lead and lift with farm yard manure and pesticides in exacavated tree pit, tree pit, shrub area including watering, ramming well, consolidating, compacting and dressing etc. complete, as directed by engineer in charge. Excavation shall be paid in revevant tender item.

Providing material and labour for fixing External trim with design lever handle of approved make suiting the panic bar for fire and smoke check doors for max. 60mm thick door prepared for half euro profile cylinder and in Silver finish with necessary fittings etc. complete for all floor all height as recommended by manufacturer and as directed by Engineer in Charge.

SITC of 32 A FP MCB

WATER COOLERS: Supplying and erecting water filter cum purifier with ultra violate technology. (Aquaguard / waterdoc model or equivalent symphony/ crystal/videocon model)

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. BLOCK-D HVAC PANEL As per Single line diagram

Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. Internal Work - Exposed on wall - 18.1.2 - 1620 (20mm OD) pipe

Providing and arranging in position 3 seater gang seating for visitors of Nano of Godrej or equivalent of sapproximate size 1630mm (L) x 570mm (D)x 400mm seat height and 650mm total height. Gang seater shall be made of powder coated MS ERW tube, chrome plated made of cold rolled steel, powder-coated perforated shell, chrome plated solid steel for differant elements.

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. BLOCK-D POWER PANEL As per Single line diagram

SITC of of 3 compatement 225 mm x 38 mm, 1.6mm thick, under floor metal trunking/race way with all accessories made out of hot dip pre galvanized metal coated steel sheet.

Supply, installation, testing and commissioning UL listed Quartzoid Bulb type Sprinkler Heads. (Standard Response): Upright Sprinkler 68°C standard response

Supply, Installation, testing, commissioning of UL listed, BTL approved IP BASED Open protocol INTEGRATOR with Inbuilt web browser & with max 150 device capacity, multiprotocol supported & should be of the same make as the DDC : INTEGRATION OF FOLLOWING SYSTEMS ON MODBUS-rtu / BACNET: The corresponding mentioned third party vendor shall be responsible to provide serial converter [RS 485 to RS 232] and the BMS vendor to accommodate the software address required for integration. including all necessary mounting hardware and accessories. as per technical specification etc. as required. for Chiller Units Soft Data Integration on Modbus / Bacnet Over IP as per technical specification etc. as required.

Providing and Fixing SS 304 Grade Satin Finish 1.8 mm Thickness Aldrops of 16 mm dia x 250 mm including 3 nos. fixing Bracket and 1 no. locking bracket of approved make with necessary MS nickle Plating Bolts etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

VALVES WITHOUT INSULATION Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 32mm dia.

TYPE-4 Supplying, installation, testing and commissioning of Layer 2 Fully manageable networking switch, 48 # 10/100/1000Tx ports, all 48 ports shall be capable of providing PoE+ as per 802.3at, minimum 2 SFP+ ports. as per technical specification etc. as required.

Supply, Installation, Testing and Commissioning of Wireless indoor Access Point supporting Dual band with 802.11a/n/ac (5 GHz) and 802.11g/n (2.4GHz) concurrent operation with MIMO support 3x3, 3 spatial streams, One 10/100/1000 BASE-TX auto-sensing (RJ45) PoE port, as per technical specification etc. as required.

Providing and placing in position personal locker of size 380mm (W) x 450mm (D) x 300mm (H) of Gorej or equivalent made with rigid knock down construction. 6 no of Locker unit shall be stacked in one height. Add-on units shall be stacked width wise to form bank of lockers having common side panel. Lockers shall be made out of CRCA sheet and finished with epoxy polyester powder coated to the thickness of 50 microns. Locker shall be with 10 lever cam lock, handle, lable holder and ventilation.

Sec.3.0 Centering & Form works Providing material and labour for formwork for exposed concrete surfaces (Only extra addition cost on normal shutering) (vertical or horizontal surface) in smooth finish, desired pattern and size as per drawing and specifications, including rendering with white cement and grey cement, using laminated shuttering plywood, for vertical and steel or laminated plywood shuttering for horizontal surfaces for all types RCC elements like slabs, walls, columns, beams, folded staircase (all sides), sill, coping, lintels, jambs, beam hunching, vertical fins, pardi etc. including neat cleaning the exposed concrete surface, as directed by the engineer-in-charge. In case of round window opening in exposed RCC wall, for payment of expose shuttering opening cutout shall not be deducted (both side). Rate shall be applicable for all floors, all levels, all places and all shapes. The contractor shall submit shuttering pattern including tie-rod hole position based on architectural conceptual drawings. (Same kind of shuttering material should be only used for standard and residual sizes.) Tie-rod hole shall be filled with polymer mortar/ polymer concrete as per manufacturer's specification.

Providing material and labour for fixing SS 304 satin finished set of narrow style dead lock of approved make with 25mm /35 mm set back necessary euro profile pin cylindrical lock 60/ 70 mm for Key and or knob operation and one pair of SS 316 grade Escutcheons (key hole plate) for aluminium door with necessary SS Phillips head screws etc complete for all floor, all level, all height as per approved sample and as directed by engineer in charge. The lock shall be with 3 keys.

Providing material and labour for laying Half brick masonry in common brunt clay building Conventional bricks having crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in superstructure for all Floor in any shape and thickness including finishing, racking of joints, curing, scaffolding for all height all level etc. complete as directed by engineer-in-charge.

Supply, installation, testing and commissioning of hand held portable operator terminals.(POT) touch screen type, shall be able to view graphs , alarms , parameters etc These shall be required if the Controllers and Integration Units do not have a built in keypad on the facia . With required connectors etc. - 4inch. as per technical specification etc. as required.

Dismentaling tiled of stone floors/ wall tiles laid in mortar including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift.

Sec.13.0 Demolition & Dismantling Work Demolition including stacking of serviceable materials and disposal or unserviceable materials at nonobjectionable place with all leads and lifts including cutting the reinforcement, and finishing the broken surfaces to match with the surroundings etc. complete : RCC Works.

Providing and fixing Polyethylene - Aluminum - Polyethylene (PE-AL-PE) composite pressure pipes conforming to IS: 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers, & connectors etc. with clamps at 1.00 meter spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. Internal Work - Exposed on wall - 18.1.1 - 1216 (16mm OD) pipe

Supplying, installation, testing and commissioning of UTP CAT6 RJ45 ethernet patch cord - 3 feet as per technical specification etc. as required.

Supply, Installation, testing, commissioning of UL listed, BTL approved IP BASED Open protocol INTEGRATOR with Inbuilt web browser & with max 150 device capacity, multiprotocol supported & should be of the same make as the DDC : INTEGRATION OF FOLLOWING SYSTEMS ON MODBUS-rtu / BACNET: The corresponding mentioned third party vendor shall be responsible to provide serial converter [RS 485 to RS 232] and the BMS vendor to accommodate the software address required for integration. including all necessary mounting hardware and accessories. as per technical specification etc. as required. of software interface for Access Control System . as per technical specification etc. as required.

Providing material and labour for laying in position Ready Mixed M-35 grade concrete for reinforced cement conctere work, using cement content as per approved Design Mix without Fly Ash (Min cementitious level as per latest IS 456 shall be maintained) manufactured in fully automatic batching plant and transported to site of work in transit mixer for all lead having continuous agitated mixer, as per mix design for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying; cost of admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability; finishing, compacting, vibrating, curing etc including cost of Form work but excluding the cost of reinforcement etc complete for all elements, all floors, any heights/depths, any lead and lift as directed by Engineer Incharge.

Supply, installation, testing and commissioning of cabinet type Floor Mounted / Loft Mounted Type single skinned Centrifugal Fresh Air Unit; unit shall have leakproof canvass connection along with damper at suction side & descharge side cowl; ready to start unit hooked upwith 4P TEFC with IP 55 protection motor with pully / belt drive arrangement on adjustable frame; fan motor assembly mounted on corrossion proof-painted MS baseframe; baseframe to rest on vibration isolation pads. The unit shall be supplied with Starter Panel of required motor capacity. 10500 CFM / 40mm Static Pressure for Washing, Drying & Press

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing & Commissioning of Floor Mounted Air Handling Units as specified below; Double Skinned powder coated inner & outer skin of 0.6 mm & 43 mm thick, 40 kg / m3 PUF Sandwitched insulated aluminium sectionalized construction Comprising of Fan section with 125 mm static best efficiency Plug type Fan driven by suitable pole Eff - 1 TEFC Motor with Drive Package driven by IP55 / 4P TEFC Fan Motor / fire resistant flexible fan outlet connection, The AHU shall comprise filter section with MERV 6 pre filter for return & fresh air, Fine filter sections with MERV 12 filter, MERV 16 filter, Cooling coil section with Chilled water Coil complete with Copper tube 12 FPI AL finned 6R deep chilled water cooling Coils, SS 304 condensate drain pan duly insulated with 15 mm thick cross linked polymer Nitrile rubber insulation, with Mixing box with Aluminium Aerofoil damper for supply, return & Fresh air, necessary vibration isolation arrangement by providing spring isolators ; Motor selection to suit the below capacity for each AHU rating by AC Vendor including transmission losses. ; Electrical Starter suitable for Respective AHUs, Panel supplied with matching rating for SA Fan motor, required DC Supply for control Valve, including short circuit / overload MCB protection, Motor Status On / Off / Trip, command, Automanual, Status contacts for remote operation through Operating Panels, Temperature Indicator availability on Panel with BAS compatiibility; Starter panel shall be minimum 14G MS powder coated with ventilation fan (only for VFD AHU Panels), inside light and duly internally wired and tested, Unit shall be supplied with Digital Thermostat with water proof casing BMS compatible with interface modbus / bacnet protocol to connect the BMS panel ; Prices to include dispatch of AHU in Semi-knocked down condition, assembly at site and lifting / shifting to actual locations as per layouts; Performance to be complied - common for below AHUs: dB=60 at 3 M distance; Price shall be complete with electrical Starters for each AHU matching the motor ratings and as specified above ; AHU dimensions, configuration (top discharge / side discharge), pipe connection side & door side shall be tailor made as per final layout and space constraints. No extra claim shall be payable for such customisation; Schedule below shows. 3600 CFM / 8.57 TR With 6.0 kW Strip Heaters & Humidistate For O.T - 4 Second Floor

Providing material and labour for fixing SS 316 grade handles 150mm long D shape hollow tube handle of approved make with both end bracket with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

Providing material and labour for laying controlled cement concrete M-30 produced in batch mix machine, using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregates conforming to latest IS 383 with minimum cement content (without fly ash) for durability shall be followed as per approved design mix and latest IS 456 for reinforced concrete work for all elements, all floors, any heights/ depths, any lead and lift including cost of formwork, compacting, finishing, curing but excluding the cost of reinforcement etc complete as directed by engineer in charge.

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Floor Heat recovery unit of 0.6mm thick Pre-Coated GI sheet Outer skin & 0.6 mm thick GI sheet metal cabinet type plain Inner skin Double skin unit with with 40 mm thick with Thermal break profile, 40 kg/cum polyurethane foam sandwiched between panels complete with pre filter of MERV -8 efficiency at fresh air inlet along with Gridblok IAQ chemical filter with turbulent flow and monolithic structure with 100 mm thick designed for 500 fpm with pressure drop not exceeding 146 pa having density 27.54 lb/ft of along with MERV-13 fine filter at fresh air outlet, MERV-8 filter at return air outlet. Fan section with direct driven plug fan & IE-3 Motor with, IP-21 variable frequency drive shall be suitable for 415 + 10% volts, 50 cycles, 3 phase AC supply. Heat reovery unti shall be wheel type of aluminium with 3 angstorn molecular sieve which is for recovery of both latest and sensible load. The unit shall have two separate passages one for supply of fresh air and the other for exhaust of cool air from the rooms after the recovery of energy, with all accessories as required. The fan outlet velocity shall be limited to 9.5 MPS maximum and face velocity across filter shall be limited to 500 FPM maximum. The unit wheel shall be min. 200 mm thick and shall be capable of recovering atleast 75% latent as well as sensible energy. The unit shall be complete as per drawings and specifications. The Photohydroionization cell with the capability to produce friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides Ions with quad metalic coating (Rohdium, silver, copper and titanimum) and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into the conditioned/ served space. The honeycomb matrix shall not be accepted. The units should be designed after undertaking a load factor calculation for each specific area where the equipment is to be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the units. The system shall be capable of reducing microbial bacteria, virus and spores , VoC’, odors and particulates matter. The equipment shall conform to UL 1598 CAN/CSA C222 EN60335-1, EN60335-2-65, EU standards, certifications shall be submitted along with the technical submital. Supply air fan - 1825 cfm, external static 50 mmwg Exhaust air fan - 1750 cfm, external static 50 mmwg

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Actuator

Providing material and labour for laying machined cut average 25mm thick River wash finish Green Kotah stone of size 1500mm of approved quality, selected and sorted for uniform color & texture, in floor, otta, tread, riser, ramp etc. of specified size as per design normal pattern (straight or staggered joint with square or rectangular shaped stone) and drawings. Kota stone is to be laid over cement mortar 1:6 bedding of average 20 mm thickness with keeping groove (upto 10mm wide), filling the groove with cement mortar in 1:2 (1 cement : 2 sand) with matching pigment, in 5mm less thickness of kota stone, and finishing including curing and cleaning with wire brush to remove excess cement on the sides of stone, pencil sharped exposed edges having polishing up to the satisfaction of the Architect & engineer in charge etc. complete for all places/ all levels/ all heights. Sample and mockup shall be approvd procurement of material.

Supplying and laying following sizes PVC pipe of approved make including excavation of trenches, laying the pipe as per layout and drawing and re-filling the trenches etc. complete as directed. Heavy gauge pipe in Open / Concealed manner minimum 90 mm dia.

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Decorative Wall Mounted type Chilled Water based High Wall type Fan Coil Units with energy saving Single Phase BLDC motor / EC Motor (Electronically Commuted Motor), Filter section with prefilters, Hydrophilic Al fins and Copper Chilled / Hot Water multi step Cooling Coil section with minimum 2 Row and minimum 13 FPI Chilled Water Cooling Coil, combination of Automatic/ Dynamic Balancing valve and an in-built 2 way ON / OFF control valve of minimum PN 16 rating with pair of brass ball valve with "Y" strainer set, fixed outside FCU, Cu piping with required couplings to fit CHW field In / Out piping; All piping are to be insulated with closed cell elastomeric nitirile rubber insulation. Unit shall be supplied with Digital Display type cordless remote and capable of connecting with BMS with interface modbus protocol to connect the DDC panel (230V operating / Power On / Off provision, 3 speed fan switch & Temp Edit facility / Digital Temp Display) and supplied with 10 RMT cable from Controller to FCU as required. The Performance of units should be certified by a reputed third party agency and available for witness testing facility at manufacturer's factory. 300 CFM

Supplying, installation, testing & commissioning of intelligent addressable duct detector including suitable Photo detector complete with base as required. as per technical specification etc. as required.

Providing and arranging in position FIXED SS TOP SQUARE STOOL of Godrej or equivalent. overall dimension of 420(l) x 420(w) x 515mm (h). Top should be made of SS 304 sheet with buffed matt finish. MS square flat tube of section 25 x 25mm with thickness of 2mm should be used. Thermosetting epoxy polyester powder coating must be done for all MS parts. Neoprene shoes should be provided at the base of legs.

Supplying, installation, testing and commissioning of Client PC - Industry standard Intel based platform computer system. Intel Core i7 latest generation, 4 GB of RAM DDR3 ,1 TB SATA II hard drive for OS and VMS applications, NVidia card 1 GB graphics card , 1600 x 1200 or higher screen resolution, 1 X 1000Mbps ethernet network interface card ,16x DVD+/- RW Drive alongwith appropriate licenced Operating System, licenced applications suites from OEM and application licences as per the technical specifications etc. as required.

Providing material and labour for fixing SS 316 grade push-pull pair of handle of size 300 mm long x 22 mm dia made out of satin (brush) finish hollow pipe of 1.5mm thick having offset type (C or D shape)/ H-shape/ D-shape of approved make with necessary screws etc. complete for wooden doors/ aluminium doors/ metal doors for all heights, all floors and all level as per approved sample and as directed by Engineer-in-charge. Rate shall be The length of handle should be perfect center to center as below specified.

Providing material and labour for fixing powder coated two point lock with mortise handle (without lock) of approved make with heavy gear mechanism of required capacity including all required accessories like handle, fork, connector, extensior, polyamide, locking point, corner transmission and striker etc as per approved manufacturer recomendatation for aluminium casement door and window (top hung or side hung) with necessary screws etc. complete for all floor, all height, all level as per approved sample and as directed by engineer in charge.

SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 10 Sq.mm x 4C CU. Cable

Providing material and labour for fixing in position PVC pipe sleeves of 160mm Diameter - 6Kg/cm2 and length as per design for following diameters for services wherever pipes pass through walls/ slabs/ beam in mtrs length. All pipes shall be accurately cut to the required sizes, laid as per drawing, kept in the position while concreting, and burrs removed before laying etc complete for all floors, all height as directed by engineer in charge. Open ends of the pipe shall be closed as the pipe is installed to avoid clogging while concreting. Pipe sleve shall be remoed before water proofing or grouting (at rain water down take location).

ELEVATOR FOR BUILDING - G + 2 Supplying, Erecting, Testing & Commissioning the passenger / stretcher lift having following main features: 20 passengers . G + 2 with Rated Speed of 1.5 m/sec - 1.75 m/sec with micro proce/PLC control and ACVVVF. drive, Duplex Control, Machine Room Less (MRL) - PREMIUM CATEGEROY Make : OTIS, Mitshubishi & Schindler Only (Joint Venture will not be allowed) [1] GEAR LESS LIFT DRIVE comprising of High Starting torque Lift duty 3 phase 440 V A. C. Permanent magnetic synchronous motor of proper rating with high efficiency shall be used. [2] Micro processor based / PLC, ACVVF, vector control drive with encoder feedback closed loop system shall be used for lift car and door operation which shall be full collective selective operation hall call demand response, UP/DOWN hall stops, Main, Up/ Down Contactor with overload and phase reversal relay and safety controls. [3] Car with M S platform with bracings of adequate size and to sustain the impact load cabin + passenger with safety factor of fire for steel and side panels of Stainless steel of sheet of grade 304 duty. Car ceiling will be S.S. finishes with aesthetic appearance with LED ceiling lights. Car flooring shall be of anti skid PVC/Granite with choice of colour of engineer in charge. Car doors shall be of stainless steel grade 304, hairline finish with centre opening / telescopic automatic doors. Car panel will also be S.S. 304 finished with emergency stop device, mechanical door safety device, facility of auto/ attended mode. All car panel buttons and all floor switches must be with brail language as per lift act. S.S. Hand rail at 900 mm height for all three side. Door must be clear 900 mm centre openable. [4] All landing doors shall be fully automatic centre opening/ telescopic opening made of hairline finish steel grade of 304 with key holes and infrared curtains with Unlocking facility from outside. [5] Appropriate battery operated emergency light in the car along with alarm switch shall be provided. [6] Digital scrolling indicator system for up-down arrow along with floor position indicator shall be provided inside the car and at all floors. [7] Full height infra red curtain with multiple criss / crossing light beams shall be provided. [8] Automatic Rescue Device (ARD) shall be provided accordingly of passenger capacity. [9] Audio visual indication in the lift car showing over loading shall be provided such that doors kept open till excess load is removed. [10] Spring buffers/PU Buffers shall be provided. [11] Car fan with automatic sleep timer shall be provided. [12] Voice annunciater with suitable music shall be provided in lift car. [13] Self diagnostics system for operational and safety parameters shall be provided in control panel. [14] Mechanical over speed governor, door key holes in the floor doors, fireman switch shall be provided. [15] Lift machine hoisting arrangement in the lift machine room and monkey ladder for lift pit should be provided by the Contractor, along with the other steel structure works, foundations for the machine etc… [16] In the hoist way fascia plate shall be provided without any extra cost, where ever required as / if directed by engineer in charge. [17] Permanent wiring in lift machine room and lift well with proper numbers of light points, with fixtures, exhaust fan and plug points shall be provided by the agency. Power supply of 3 phase 440 V shall be made available by department in lift machine room. [18] Any civil/ electrical works for additional and alteration in lift shaft and machine room related to erection of lift shall be made by contractor without any extra cost.(granite/marble fixing around all landing door openings are in contractors scope.) [19] Agency has to provide all working drawings and documents and liaison services for obtaining all necessary permission from lift inspector and other authorities. [20] As per statutory requirement of Got. Of Gujarat lift & escalator act 2000, contractor has to provide 1. Car top safety barricade 2. Push & talk communication system. 3. Fireman's switch operation at Ground Floor

Providing and fixing concelled type Auto drop down seal of PR Arch Solutions or CCE (Itly) or approved for door shutter of size 28mm x 13mm made out of aluminium with silicon and fixed at bottom of shutter as per approved sample and as directed by engineer in charge.

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Ceiling Suspended Chilled Water Fan Coil Units as specified below with; Single Skin Fan Coil Units in standard construction with Fan section with DIDW multi blowers & energy saving Single Phase BLDC motor/ EC Motor (Electronically Commuted Motor), Filter section with prefilters, Hydrophilic Al type Copper Coil section with minimum 3 Rows and minimum 13 FPI Chilled / Hot Water Cooling Coil, pre-assembled valve station with set of brass ball valve with "Y" strainer set, Insulated extended L shaped Drain Pan, supplied with pre-calibrated matching size 2 way / Pressure independent modulating cum balancing valve of minimum PN25 rating with P/T plugs and minimum IP54 t electrothermic / motoric modular actuator (0 to 10 Volt DC Signal), fixed on FCU Cu piping with required couplings and ends flanged to fit CHW field In / Out piping and its compatible 24VAC control transformer; All valve assemblies are to be insulated with closed cell elastomeric nitrile rubber insulation. UNit shall be supplied with Digital Fan Coil Thermostat with Fibre water proof casing BMS compatible with interface modbus protocol to connect the DDC panel (230V operating / Power On / Off provision, 3 speed fan switch & Temp Edit facility / Digital Temp Display) and supplied with 10 RMT cable from Controller to FCU as required. The Performance of units should be certified by a reputed third party agency and available for witness testing facility at manufacturer's factory. 300 CFM

Providing material and labour for fixing of expansion joint system for 100mm wide gap of approved make related with External wall joint location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning/ centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner, with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall conform to ASTM 6063). Rate shall be inclusive of polyester powder coating of approved shade and make. Expansion joint system shall be as approved for all floor all level including scafolding etc complete as dircted by Engineer in charge.

Extra for providing material and labour for Grouting the joints of any type of flooring tiles of Size upto 600mm having joints of 3mm width and in full depth, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade and approved make (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge.

Providing and laying rubble soling in plinth and sub-base of road, compacted thickness specified as following, using specified size of hard stones for average 150mm thick soling, filling, covering and leveling the surface with a layer of earth after filling the voids (upto 25%) with sand, smaller sized black trap stones 20-40mm, 40-63mm, 63-90, 90-150mm size of stone/metals or stone chips, including watering, ramming well and compacting or consolidating each layer by static roller/ vibratory roller of required capacity as directed by Engineer-in charge.

Supplying & erecting approved make Telephone Cable electrolytic copper conductor PE insulation twisted in two pairs & wrapped with FR PVC tape & sheathed with FR PVC or HFFR outer jacket suitable for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos. of pairs. With necessary connections. A Conductor Size 0.5 mm, Armoured. (Jelly Filled), Two Hundred Pairs.

Supply, Installation, Testing and Commissioning of System Switch / Ward Controller: forms a decentralised communications node for exchanging data between the connected system devices and the rest of the communications system. It should have , - 1 x RJ45 socket, 100Mb IP Uplink Port galvanically isolated conformant with EN 60950 and VDE 0834 - 7 x RJ45 sockets, each with a 100Mb POE port - 1 x RJ45 socket, 100Mb IP POE Port (IEEE802.3 100BaseTX) for connecting Staff Room Devices - 2 x RJ45 sockets for connecting the external data bus including 230VAC / 24DC , 5 A power supply.

INSULATED VALVES Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 250mm dia.

Supplying, installation, testing and commissioning of Networking enclosure - Floor mounted, 19" mounting frame, usable height 24U, 600mmW x 600mmD etc. as per technical specification etc. as required.

SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 70 Sq.mm x 3.5C Al. Cable

ELW 14.00 Internal Wiring WITH MODULAR TYPE SWITCHES Wiring of points to be done in open/concealed manner in 25 mm dia medium guage Rigid PVC FRLS pipe. Wiring shall be done with FRLS type copper flexible wire of 650V/1100V. Separate pipe should be taken for circuit mains. Nos of ciruit of the same phases may be taken in same conduit .The circuit shall be laid in 25/40 mm dia medium guage rigid PVC FRLS pipe.The point rate shall include all the necessary piping and wiring from sub panel / Distribution board to switch board & switch board to the batten holder / angle holder / connector / ceiling rose all inclusive except sub panel / Dist board. The wiring shall be done as per relevant prevailing standard. The looping of the wiring should be done in the switch boxes or light and fan point outlet boxes to avoid the junction boxes. The junction boxes and switch boxes for the ceiling light point, fan point etc shall be minimum 60/75 deep. All the necessary jarry in brick plastered walls should be done with machine cutter only , also jarry should be filled with cement, sand and wire mesh as required, the material cost for rough finish shall be included in point rate.Whenever pipes are required to be laid in flooring shall be of.Wiring should be done as per distribtion details. Each circuit should have dedicated phase, neutral & earth wire. Wire sizes to be used as under For Light Points /fan point/ wall fan / 6A 3 Pin Plug - DB to SB - 2.5sqmm for Phase & Neutral & 1.5 sqmm for Earth - SB to on board Point - 1.5 sqmm for Phase & Neutral & Earth For 6A Plug point. - 1.5 sqmm for Phase, Neutral & Earth For 6/10/16A general purpose plug point - 2.5 sqmm for Phase, Neutral & 1.5 sqmm Earth For 16A plug point for A/C and Geyser - 4 Sqmm for Phase, Neutral & 2.5 sqmm Earth For 20/32A plug point - 6 sqmm for Phases, Neutral & 4 sqmm Earth No zarry will be allowed in expose brick work. The conduit shall be provided when the walls are under construction. The pipes in slab shall be laid before the slab is casted. One light point controlled by one single way 6 A switch.

Providing material and labour for laying average 25 mm thick machine cut polished Green kota stone slab of size upto 2.1mt length for riser of stair over 12 mm (average) thick base of cement mortar 1:6 (1 cement : 6 coarse sand) laid over and jointed with gray cement slurry including polishing, rubbing, curing, finishing, buffing after final polishing, maintaining upto handling ovre the project etc complete as directed by engineer in charge. The rate shall be inclusive of making rebates of 10x10mm for forming the grooves between treads and risers with polishing inside the groove. Sample shall be approved before execution. Sample and mockup shall be approvd procurement of material.

Supplying and laying following sizes PVC pipe of approved make including excavation of trenches, laying the pipe as per layout and drawing and re-filling the trenches etc. complete as directed. Heavy gauge pipe in Open / Concealed manner minimum 110 mm dia.

Providing material and labour for fixing 6mm thick frame less mirror of approve make in any shape and sizes as per drawing. Mirror shall be fixed on 6mm thick cement bonded particle board (Bison panel) backing. Cement bonded particle board shall be fixed to wall with approved SS 304 fastener. All edges of glass shall be grinded (as required), cute corner and polished. Glass shall be fixed with silicon sealant/ 3M tape etc complete at all floors/ all levels/ all heights as directed by engineer in charge. Installed area of mirror shall be considered for payment without wastage.

Providing material and labour for Excavation of foundation from 1.5 mt to 3.0 mt depth including sorting out and stacking of useful materials and disposing off the excavated stuff with in the campus for all lead, all lift/ depth and back filling foundations, the trenches, plot filling, plinth filling with excavted material (excluding hard rock and black cotton soil) anywhere from the site/ campus etc complete as directed by Engineer in charge. - Any type of soil or rock not requiring Blasting.

Providing material and labour for laying machined cut average 25mm thick River wash finish Green Kotah stone of size upto 600mm of approved quality, selected and sorted for uniform color & texture, in floor, otta, tread, riser, ramp etc. of specified size as per design normal pattern (straight or staggered joint with square or rectangular shaped stone) and drawings. Kota stone is to be laid over cement mortar 1:6 bedding of average 20 mm thickness with keeping groove (upto 10mm wide), filling the groove with cement mortar in 1:2 (1 cement : 2 sand) with matching pigment, in 5mm less thickness of kota stone, and finishing including curing and cleaning with wire brush to remove excess cement on the sides of stone, chemphering of exposed edges having polishing up to the satisfaction of the Architect & engineer in charge etc. complete for all places/ all levels/ all heights. Sample and mockup shall be approvd procurement of material.

“Providing & erecting approved make Card Personality Module (CPM) having following features “(A) EM proximity Card Reader Module [Low Frequency] “(B) Compatible with any COSEC Door Controllers and COSEC Reader CA “(C) Supports EM Proximity Card”

Providing and fixing high quality 35 to 40 mm thick FRP water gully cover wothout frame of required size of 5 T capacity having the load tested as per BSEN 124, Is1726 & AASHTO M306 standards of approved make and shade. Gully cover shall be directely fixed on wall of RCC channel as per drawing and as directed by Engineer in charge. Actual installed area of cover shall be meaured for payment with out considering any wastage.

WATER COOLERS: Supplying and erecting approved make water filter having outer body of tough polycarbonate with fitter cartridge having filter to trap micro elements with coupling suitable for erection on pipe line.

Supply, Installation, Testing and Commissioining of IP based Networkable touch screen paging station for selection of zones, supervision of system status, setting of scheduled broadcasts with the following functions: Built-in monitoring loudspeaker, Detachable goose-neck microphone, LCD touchscreen display, Audio input as per technical specification etc. as required.

Providing, fixing AUTO GLOW photo luminescent Signage's as per IS standard in Block / Small Letters on rigid sheet with necessary wall or Ceiling fittings as Specified Sizes: Fire Equipment: 4" x 12"

16A /20A / 25A / 32 A DP ELCB (30mA)

Providing and arranging in position Sloted angle storage rack of size 900mm x 450mm x 1800mm (5 panel rack to making 4 no of compartment) of Godrej or equivalent and made out of powder coated MS Amgel and CRCA sheet for compartment surface.

Sec.8.0 HVAC Plant Room - Electrical Panel Supply, installation, testing and commissioning of dust, damp and vermin proof cubicle free floor, indoor type factory built sheet steel enclosed modular bolted construction extendable panel, suitable for operation on 415 ±10% volts, 50 Hz AC 3 phase 4 wire supply system fabricated out of suitable sized square tubular section and covered with CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having 1000 Amps. capacity extensible type TPN Copper bus bars of high conductivity, DMC/ SMC bus bar supports, with short circuit withstand capacity of 25 KA for 1 sec., bottom base channel of section not less than 100mmX 50mmX 3mm thick, fabrication shall be done in transportable sections, entire panel shall have a common copper earth bus bar to switch gears with required size of Copper. bus bars and inter-connection with solid copper conductor wires / aluminium strips, neutral links, including control wiring with 1.5sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor S/C cable for voltage & current respectively, cable alleys, cable gland plates in two half, etc. necessary metering protections & indications and mounted with the following switch gears as per drawing and technical specifications etc. complete as required. ( Each starter should have remote control and interlocking facilities including auto manual switch, NO/NC contacts for control). Including suitable connectivity for BMS and Remote Operation including providing sufficient number of potential free / auxiliary contacts. All outgoing shall be provided with Stop/Manual/ Auto/selector switch to facilitate operation through BAS. All starters shall be provided with potential free Contact for Connections to Building Automation System. A separate set of CTs to be provided for BAS and wiring from CT’s and voltage transducers to be brought on to separate set of terminals. Incoming: 1 No.- 1250Amp. TP + N Air Circuit Breaker Horizontal Manual drawout type of fault breaking capacity 50kA (Ics=lcu =Icw for 1 sec. at 415V), impulse voltage (Uimp) 8KA, insulation voltage (Ui) 1000V, fitted with interlocked door, automatic safety shutters, 6NO + 6 NC auxilliary contacts, mechanical ON/OFF and service/ test/ isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as amended up-to-date complete with following accessories Independent Electrical / manual spring closing mechanism - I set. Microprocessor release (EMI & EMC certified) for over current, earth fault & short circuit protection - I set. 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB, test terminal block set, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required. 1 set - multifunction digital meter to read V, Amp, KW, KWH with 3 nos. resin cast CT's of 1250/5A class 1.0 accuracy and 15 VA burden. Shunt trip coil 220V A.C. Bus Bar : TPN Copper extensible type main bus bars of minimum of 1250 Amp capacity and auxiliary bus bar of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 25 KA for 1 sec. Outgoings: 4 Nos. 315 Amp three pole microprocesser release, MCCB (Ics=Icu at 415 Volts) with O/L, S/C & built-in earth fault protection, and outgoing feeders to 4 Nos. 140 KW starter panel and outgoing feeders to 4 Nos. chilling unit compressor motor. The MCCB compartment shall contain : with folloxing accessories for each MCCB's 0 - 500 volts 96 x 96 sq mm digital voltmeter with selector switch. 0 - 400 amps 96 x 96 sq mm digital ammeter with 400/5 amps CT’s and selector switch Over voltage tripping mechanism for persistent voltage exceeding 110% of the rated voltage for more than 5 minutes. Phase indicating lamps, with toggle switches. TPN bus bars shall be of Aluminium and shall be sleeved. Phase bus bars shall be rated at 400 amps and neutral bus bar shall be of 50% capacity. Maximum density of aluminium bus bars for current carrying capacity shall be 1.4 amp per square mm. 4 Nos. 32 amps TPN MCCB 10 HP / 7.5 KW star delta starter, over load relay with built in single phasing protection and outgoing feeders to condenser water pump motors. Each of these compartment shall contain CT operated digital ammeter of 0- 32 amps range with selector switch, auto / manual / off selector switch auto / manual / off selector switch and an indicating lamp with MCB and toggle switch for ‘ON’ status of pump motors. 4 Nos. 100 amps TPN MCCB 40 HP / 30 kW and 4 Nos. outgoing feeders to Adjustable Frequency Drive (AFD) panel zone (B) and 4 Nos. outgoing feeders to secondary chilled water pump motors The compartments shall contain CT operated digital ammeter 0 - 100 amps range with selector switch and an indicating lamp with MCB and toggle switch for ‘ON’ status of pump motors. 4 Nos. 40 amps MCCB 15HP / 11 KW star delta starter, over load relay with built in single phasing protection and outgoing feeders to Primary Chilled Water pump motors. Each of these compartment shall contain CT operated digital ammeter of 0- 40 amps range with selector switch, auto / manual / off selector switch and an indicating lamp with MCB and toggle switch for ‘ON’ status of pump motors. 4 Nos. 40 amps MCCB - star delta starter with suitable 15HP / 11 kw motors / fan capacity, complete with contactors, overload protection relay, current sensing type single phase preventor, ON/OFF indications, push buttons, auto / manual / off selector switch, suitable Digital Ammeter with cast resin suitable rating CT's and all other accessories with suitable rating PVC insulated FRLS single core copper conductor cable etc. complete as required.(For Cooling Tower Fan motor) 1 No. - 160 Amp. TPN MCCB as spare 3 Nos. 63A TPN MCCB as spare Necessary cable alleys, space for spare switches, internal wiring, control wiring/cabling shall also be included. All switches and other components shall be motor duty rating. Note. MCCB’s shall be with Micro processor based release with communication port & of motor duty, suitable for 25 KA (ICS) fault current. HVAC PANEL AS ABOVE

Providing material and labour for laying controlled cement concrete M-20 produced in batch mix machine using graded, black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregates conforming to latest IS 383 with minimum cement content (without fly ash) for durability shall be followed as per approved design mix and latest IS 456 for reinforced concrete work for all elements, all floors, any heights/ depths, any lead and lift including cost of formwork, compacting, finishing, curing but excluding the cost of reinforcement etc complete as directed by engineer in charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised-PVC rain water pipes conforming to IS : 13592 (Type A), including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe Bend - 150mm dia pipe

SS letter sign: Providing, Making and fixing 200mm high SS 304 letter with back lited by LEDs/ SMD lightings behind the text made of 3/4" SS 304 channel (1mm thick) for signage in Gujarati, Hindi and English languages and the font style as approved sample or as per design and drawings. It shall be made from ISI Brushed S.S. 304 using Water jet / CNC cutting machine. It shall be fixed on the wall with chemical anchor fastener at any level any height. All Edges and corners shall be smoothened. Width of the letter shall as per the proportion of the word for depth 1". Stainless Steel Patti shall be argon welded. Duco paint of approved make, shade in required coat with necessary primer and putty shall be applied on external surface of letter. It shall be paid in as per alphabet no. In Gujarati/ Hindi language one letter shall considered with its contents (i.e. Kano, Matra etc.) i.e. 'chhi' letter in Guajarati shall be considered as one letter. Height of letters may vary + 3" shall be included in quoted rate. The rate shall be inclusive of scaffolding, drilling, adhesive material etc. complete for all heights.

Providing and fixing white vitreous china sink for Sluice Room, Laboratory & Autopsy Room, with C.I. brackets, 40 mm PTMT waste coupling, 40mm PTMT bottle trap, complete, including painting of fittings and brackets, cutting and making good the wall wherever required as directed by Engineer. Sink for Sluice Rooms. Sink: Make: Cera – CATER 600 x 400 x 250 mm (660 x 460 x 250 mm including rim) Cat. No. S6010103; PTMT Waste Coupling - PolyTUF - 38/40 mm - 1003 (b); PTMT Bottle Trap - PolyTUF - 40mm - 1060.

Providing and arranging in position MEDICINE TROLLEY of Godrej or equivalent. overall dimension is 902(L) X 532(B) X 915(H) mm. Top shelf & bottom shelf should be made of SS304 sheet with 1mm thickness & 1.2mm. Rest of the components like supporting legs, horizontal bar handle should be made of SS 304 pipe having dia 31.8, 12.7 mm respectively. The castors of high quality plastic injected molded & anti static having the dia of 125mm should be used.Handles made of SS 304 pipe having section of 16mm & thickness of 1.2mm should be used.

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Floor Heat recovery unit of 0.6mm thick Pre-Coated GI sheet Outer skin & 0.6 mm thick GI sheet metal cabinet type plain Inner skin Double skin unit with with 40 mm thick with Thermal break profile, 40 kg/cum polyurethane foam sandwiched between panels complete with pre filter of MERV -8 efficiency at fresh air inlet along with Gridblok IAQ chemical filter with turbulent flow and monolithic structure with 100 mm thick designed for 500 fpm with pressure drop not exceeding 146 pa having density 27.54 lb/ft of along with MERV-13 fine filter at fresh air outlet, MERV-8 filter at return air outlet. Fan section with direct driven plug fan & IE-3 Motor with, IP-21 variable frequency drive shall be suitable for 415 + 10% volts, 50 cycles, 3 phase AC supply. Heat reovery unti shall be wheel type of aluminium with 3 angstorn molecular sieve which is for recovery of both latest and sensible load. The unit shall have two separate passages one for supply of fresh air and the other for exhaust of cool air from the rooms after the recovery of energy, with all accessories as required. The fan outlet velocity shall be limited to 9.5 MPS maximum and face velocity across filter shall be limited to 500 FPM maximum. The unit wheel shall be min. 200 mm thick and shall be capable of recovering atleast 75% latent as well as sensible energy. The unit shall be complete as per drawings and specifications. The Photohydroionization cell with the capability to produce friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides Ions with quad metalic coating (Rohdium, silver, copper and titanimum) and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into the conditioned/ served space. The honeycomb matrix shall not be accepted. The units should be designed after undertaking a load factor calculation for each specific area where the equipment is to be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the units. The system shall be capable of reducing microbial bacteria, virus and spores , VoC’, odors and particulates matter. The equipment shall conform to UL 1598 CAN/CSA C222 EN60335-1, EN60335-2-65, EU standards, certifications shall be submitted along with the technical submital. Supply air fan - 1050 cfm, external static 50 mmwg Exhaust air fan - 1750 cfm, external static 50 mmwg

Providing and fixing stainless steel (Grade 316) Railing and baluster system of approved make stair railing, hand rail, bump rail, guard rail, with knock down system made of Hollow or solid secion i.e. tubes, square, flat, plates, bar etc with base plate Cover cap, finishing accessories, infilled holding brackets, fixing accessories etc. for any type of design, shape (plain/ curvature), size as per drawing. Railing shall be top mounted or side/ wall mounted. Railing shall be fixed with SS 316 grade anchor fastner of required size and as per fixing position of approved make. No Welding OR Fabrication shall be allowed at site. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Sample shall be approved before execution. Contractor shall arrange mock up of railing system (2 or 3 no) in required length as directed by Architact and Engineer in charge. Contractor shall protact railing system uptill handeling over the project.

FRP Recessed Man hole cover Providing and Fixing heavy duty double seal FRP Manhole cover with frame of 25MT capacity, in matching shade of surrounding pavement and design according to EN - 124:1994 of HP or equivalent of clear opening size of 600mm x 600mm and recesse depth 80mm, with client's logo etc. complete as approved by architect and as directed by engineer in charge. Frame shall be embaded in concrete of M25 grade and top level of frame shall be flush with road level. Frame and cover shall be with 4 number lifting key with proper lifting arrangement. Rate shall be inclusive of cover frame and concrete work. The rate includes carting upto any lead from store to site as per directed by engineer in charge.

Providing and fixing PTMT grating of approved quality and colour: Rectangular type with openable circular lid: 150 mm nimnal size square 100 mm diameter of the inner hinged round grating.

SITC of Brass glands & making joint with necessary bi metalic crimping socket of long nack type connecting the same to various equipment/panel/DB etc. for the following sizes: 150 Sq.mm x 3.5C Al. Cable

Sec.15.0 General Development and Road works Box cutting the road surface to proper slope and camber for making a base for road work including removing the excavated stuff and depositing on the road side slope as directed upto 1 Km lead and all lift.

Supplying, installation, testing and commissioning of UTP CAT6 RJ45 ethernet patch cord - 7 feet as per technical specification etc. as required.

Sec.3.0 Fire Detection & Alarm & Digital EVAC System Supplying, installation, testing and commissioning of microprocessor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. Irrespective of whether or not mentioned in the boq, all necessary interfaces - such as hardware and software - for interconnecting all fire alarm panels at site shall be provided in the system(s). Ten Loop Panel

Providing and arranging in position STRETCHER ON TROLLEY of Godrej or equivalent. overall dimensions 2000mm(L) X 660mm(W) X 825mm(H). The trolley should be made of 31.75 and 25.4 mm dia 1.6 mm thick ERW tube. hollder for stretcher should be made up of mild steel Castor should be of 200 mm dia, diagonal locking castor. stretcher should be made up of ERW tube of dia 25.4 mm and thickness 1.6 mm Top sheet should be made of CRCA sheet of thickness 1.2 mm with contour shape to accommodate patient. IV pole holder should be made of MS. All metal components should be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbial epoxy polyster powder coating. stretcher on trolley in knocked down construction. The manufacturer should compilant with ISO 9001, 14001, 13485, OHSAS 1800 and CE certification.

ELW 19.00 UPS Supply, Installation, Testing & Commissioning of ON LINE UPS system with 15 mins battery backup and with battery rack complete in all respect. 20KVA UPS 3 ph in 3 ph out for balance load

40 mm Dia.

Wall projected Providng and fixing of Modular Signages using Aluminium extrusions (Alloy 6060) with Anodizing (Thickness 15-20 microns). ISO:9001-2008 product with Premium grade Anodizing as per Qualanod and Qualicoat International standards. Internal graphics to be made of 3M vinyl printed with Hp latex 3rd Gen Eco friendly non toxic inks with UV lamination and 2 year print warranty. Sign panel shall be finished with anti-reflex cover 1mm thick with one side Matt and other side Glossy finish. Polypropylene (PP) End caps which can be fixed to the extrusion with the help of screws. Panels shall be clicked on to the end caps. Projection Bracket shall be of 3mm Aluminium extrusions having Anodized finish (same as framing). Projection Bracket shall be fixed on wall with SS 304 screw and signage panel shall be laid on aluminium framing as per manufacturer's specification. Rate shall be inclusive of total modular signage system for all level, all height etc complete as directed by engineer in charge. Sampe shall be approved before execution and mockup shall be done with approved sample for 2 to 3 number of signage.

CABLE END TERMINATION AND CONNECTION Supply, fixing, connection, testing & commissioning of single compression brass cable glands and crimping type Bimetalic lugs / sockets with necessary tools and equipments as specified in specifications and IS. The glands and lugs / sockets shall be suitable for cable size and type mentioned above. The job also includes, if necessary, supply and fixing of extension busbar of same material on circuit breaker or panel board terminal / connector to connect more than one no. of parallel cables or to connect higher size cable to lower size unit. The job also includes earthing the glands and armour of the cable with common earth bar or flexible copper mesh. 3C X 4 SQ. MM. CU XLPE CABLE

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. BLOCK-C UPS POWER PANEL As per Single line diagram

Sec.6.0 Miscelleneous Works Supply, installation, testing & commissioning of Ceiling Mount Cassette type Exhaust Fan. - 200 CFM

Providing and fixing unplasticized PVC SWR as per IS: 13592 (Type B), vent cowl as approved and directed by the Engineer-in-charge. For 110 mm Dia pipe

Providing & erecting approved make Application Software Platform for 500 User having following features “(A) With 100 Users “ (B) Expandable up to 500 Users with COSEC USER 100 “(C) Supports up to 16 Door Controller “(D) Basic Access Control Basic Time Attendance and Enrollment Management (E) Compatible with all COSEC Hardware “(F) Add Other COSEC software modules on requirement.

INSULATED VALVES Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. SS BALL VALVE complete with Flanges Nutbolts with SS Body and Working parts. 32mm dia.

Supplying, installation, testing and commissioning of Laser Jet B/W Printer - A4 Size. as per technical specification etc. as required.

Supply, testing and Laying and commissioning of XLPE steel wire/flat armoured cable of 1100 V grade of Copper Conductor of following sizes in ready made trench or mounted on wall with necessary clamping arrangement or in pre-laid RCC hume pipe with necessary cable identification mark to be provided at distance of 10 mt. The vertical cable on wall shall be drawn in prelaid conduit for vertical mechanical support. 10 Sq.mm x 4C CU. Cable

Providing and placing on terrace (at all floor levels) polyethylene water storage tank as per IS: 12701, marked with cover and suitable locking arrangement and making necessary holes for inlet, oultet, and overflow pipes but without fittings and the base support for tank. (Each tank of 5000 liters capacity)

INSULATED VALVES Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. AUTO BALANCING VALVE complete with Flanges Nutbolts and Working parts 80mm dia.

Providing and arranging in position work table with CPU hanger system and modesty panel of Enterprise 1500 of Godrej or equivalent of approximate size 1500 Width mm x 750 Depth mm x 725 Height mm with knock down construction system. Total assembly shall be maade of 25mm & 18mm thick prelaminated partical board of approved shade with PVC membrane pressed on it, PVC lipping at exposed edges, CRCA member and MS ERW tube finished epoxy polyster powder coating, Required hardware shall be provided i.e. wire management system, plastic cap for cable travel, leveler glide, handle, lock, sliding mechanisam etc.

Providing material and labour for fixing 6mm thick Compact Sheet of any size, any shape, any color (single side, double side coloured), any texture of approved make and as per approved sample (approved by architect). Compact sheet shall be fixed in aluminium frame and shutter work with necessary cutting of sheet, provision of groove, filling of groove (both side) as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ adhesive tape/ screwing on the periphery of the sheet as per the required thickness etc. complete at all floors/ all levels/ all heights as per the drawing & directed by Engineer in charge. Cut edges of the compact sheet shall be provided with masking tape. Actual installed quantity shall be measured and paid.

INSULATED VALVES Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications. AUTO BALANCING VALVE complete with Flanges Nutbolts and Working parts 25mm dia.

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing & Commissioning of Floor Mounted Air Handling Units as specified below; Double Skinned powder coated inner & outer skin of 0.6 mm & 43 mm thick, 40 kg / m3 PUF Sandwitched insulated aluminium sectionalized construction Comprising of Fan section with 65 mm static best efficiency Plug type Fan with variable frequency driven (VFD) by IP55 / 4P TEFC Fan Motor / fire resistant flexible fan outlet connection, The AHU shall comprise filter section with MERV 6 pre filter for return & fresh air, Fine filter section with MERV 12 filter, Cooling coil section with Chilled water Coil complete with Copper tube 12 FPI AL finned 4R deep chilled water cooling Coils, SS 304 condensate drain pan duly insulated with 15 mm thick cross linked polymer Nitrile rubber insulation, with Mixing box with Aluminium Aerofoil damper for supply, return & Fresh air, necessary vibration isolation arrangement by providing spring isolators ; Motor selection to suit the below capacity for each AHU rating by AC Vendor including transmission losses. ; Electrical Starter suitable for Respective AHUs, Panel supplied with matching rating for SA Fan motor, required DC Supply for control Valve, including short circuit / overload MCB protection, Motor Status On / Off / Trip, command, Automanual, Status contacts for remote operation through Operating Panels, Temperature Indicator availability on Panel with BAS compatiibility; Starter panel shall be minimum 14G MS powder coated with ventilation fan, inside light and duly internally wired and tested, Unit shall be supplied with Digital Thermostat with water proof casing BMS compatible with interface modbus / bacnet protocol to connect the BMS panel ; Prices to include dispatch of AHU in Semi-knocked down condition, assembly at site and lifting / shifting to actual locations as per layouts; Performance to be complied - common for below AHUs: dB=60 at 3 M distance; Price shall be complete with electrical Starters for each AHU matching the motor ratings and as specified above ; AHU dimensions, configuration (top discharge / side discharge), pipe connection side & door side shall be tailor made as per final layout and space constraints. No extra claim shall be payable for such customisation; Schedule below shows.(With 5 Micron Filteration) 6850 CFM / 14.10 TR For Pre Op Room and Corridor at Second Floor

Sec.5.0 Ducting, Grills, Diffuser and Insulation DUCTING, GRILLS, DIFFUSER AND INSULATION Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular / round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Thickness 0.63 mm sheet

ELW 20.00 Exit sign SITC of Self contained single sided exit sign for wall / ceiling / pendant cantilever mounting with 3 W LED tube for Non maintained battery backup emergency lighting for 2 hours duration.Prolite make or approved equal in quality and design.

Design, Supply, Lifting & Shifting at actual proposed location of site, Installation, Testing, Commissioning and Field Performance Validation of Floor Heat recovery unit of 0.6mm thick Pre-Coated GI sheet Outer skin & 0.6 mm thick GI sheet metal cabinet type plain Inner skin Double skin unit with with 40 mm thick with Thermal break profile, 40 kg/cum polyurethane foam sandwiched between panels complete with pre filter of MERV -8 efficiency at fresh air inlet along with Gridblok IAQ chemical filter with turbulent flow and monolithic structure with 100 mm thick designed for 500 fpm with pressure drop not exceeding 146 pa having density 27.54 lb/ft of along with MERV-13 fine filter at fresh air outlet, MERV-8 filter at return air outlet. Fan section with direct driven plug fan & IE-3 Motor with, IP-21 variable frequency drive shall be suitable for 415 + 10% volts, 50 cycles, 3 phase AC supply. Heat reovery unti shall be wheel type of aluminium with 3 angstorn molecular sieve which is for recovery of both latest and sensible load. The unit shall have two separate passages one for supply of fresh air and the other for exhaust of cool air from the rooms after the recovery of energy, with all accessories as required. The fan outlet velocity shall be limited to 9.5 MPS maximum and face velocity across filter shall be limited to 500 FPM maximum. The unit wheel shall be min. 200 mm thick and shall be capable of recovering atleast 75% latent as well as sensible energy. The unit shall be complete as per drawings and specifications. The Photohydroionization cell with the capability to produce friendly oxidizers like Ionized Hydro Peroxides, Super Oxide Ions, Hydroxides Ions with quad metalic coating (Rohdium, silver, copper and titanimum) and duly enclosed by a poly casing tube that should prevent glass or mercury leakage into the conditioned/ served space. The honeycomb matrix shall not be accepted. The units should be designed after undertaking a load factor calculation for each specific area where the equipment is to be installed. The load shall clearly state the number of units required vis-à-vis the wattage of the units. The system shall be capable of reducing microbial bacteria, virus and spores , VoC’, odors and particulates matter. The equipment shall conform to UL 1598 CAN/CSA C222 EN60335-1, EN60335-2-65, EU standards, certifications shall be submitted along with the technical submital. Supply air fan - 3175 cfm, external static 50 mmwg Exhaust air fan - 1750 cfm, external static 50 mmwg

Supply, installation, testing and commissioning of cabinet type Floor Mounted / Loft Mounted Type single skinned Centrifugal Fresh Air Unit; unit shall have leakproof canvass connection along with damper at suction side & descharge side cowl; ready to start unit hooked upwith 4P TEFC with IP 55 protection motor with pully / belt drive arrangement on adjustable frame; fan motor assembly mounted on corrossion proof-painted MS baseframe; baseframe to rest on vibration isolation pads. The unit shall be supplied with Starter Panel of required motor capacity. 2600 CFM / 40mm Static Pressure for OT Store

Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning compartmentalized type Panels with powder coated fabricated from CRCA sheet & folded channel totally enclosed cubical type with pad lock arrangement complete in all respect as per detail tedner specifications. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Engineer In charge / Consultant.Panels should be as per detail single line drawing with required nos of incoming and outgoing feeders and accessories complete in all respect. BLOCK-A LIGHTING+SMALL POWER PANEL As per Single line diagram

SITC of approved make low noise decorative exhaust fan having size 200mm with 1350 RPM with square frame.ABS body with inbuilt lowers & square frame.

SITC of Provide expanding firestop foam on both sides of wall, with minimum 2 hours fire rating when tested in accordance with UL 1479/ASTM-E 814, for horizontal/ vertical openings in floors / wall or slabs made of concrete/ masonry or Gypsum after passing service lines like cable trays or cables/cable bundlesThe system shall be UL listed & classified and product shall bear the UL and FM approval logo on the packing. The system shall be UL listed & classified and product shall bear the UL & FM approval logo on the packing. If none of UL test certificate comply with actual application, an EJ document (as per IFC Guidelines) prepared by a qualified personnel and based on nearest third party tested & approved systems like UL test certificates & in accordance with IFC guidelines shall be producted by manufacturer.Firestop installation shall be done by manufacturer's Accredited Firestop Speciality Contractor (HAFSC) and in accordance with manufacturer's guidelines and UL system test certificates or approved EJ document.

Providing material and labour for laying approved quality average 18mm thick mirror polished Granite stone of approved shade in floor, otta in any pattern etc sizes upto 1200mm including average 20 mm thick cement mortar bedding in 1:6 laid and jointed with white cement and matching pigment including rubbing, re-polishing after fixing to remove any undulation between the joints (if required) with different grades of Emery, refilling of open joints, curing, daily cleaning and mopping, as per satisfaction of Architect and as directed by Engineer in charge at all floors/ all levels/ all heights and all shapes. (Only finished work will be measured.) Sample and mockup shall be approvd procurement of material.

Providing material and labour for laying controlled cement concrete M-25 produced in batch mix machine, using graded black trap stone aggregates of maximum 20mm nominal (down graded) size including fine aggregates conforming to latest IS 383 with minimum cement content (without fly ash) for durability shall be followed as per approved design mix and latest IS 456 for reinforced concrete work for all elements, all floors, any heights/ depths, any lead and lift including cost of formwork, compacting, finishing, curing but excluding the cost of reinforcement etc complete as directed by engineer in charge.

Providing material and labour for fixing of double shutter lead line door of average sizes 1500mm(W) x 2400mm(H) of make Pacific or equivalent make, with a 2mm Lead sheet, provision of lead glass as vision panel, with all Heavy duty hardware of make Geze, Dorma or equivalent make with following specification. Door Frame - The frame is size 143 x57 of 1.6mm thick GI sheet having polyester powder coating of 50 to 60 micron thickness. Frame shall be with 2mm thick lead sheet with and reinforced to support the load of the lead sheet. Frame shall be fixed with SS 304 grade anchor fastener (Min 3 No per side) of approved make and size. Door shutter - Door Shutter in 46 mm +2mm thick manufactured from 1.0mm GI sheets on both faces press formed, lock seam jointed at stile edges to form a double skin fully flush shell. Infilled rock wool insulation material to be provided for structural rigidity & additional reinforcements & sound Insulation with Honeycomb core infill for structurally flat surface & construction with 2 mm thick lead lining. The lead lining is located in the core of the door with other infill material. The internal construction of the door should be appropriate for all hardware fixtures and vision glass. Vision Panel - 10 mm thick Lead Line Glass. Hardware : Hinge: SS 304/316 grade heavy duty ball bearing hinge - 4 No/ shutter, 2 No Door Closer, Dead lock, push-pull pair of handle of size 300 mm long x 22 mm dia, 1.0 mm thick Kick plate, Flush bolt, Rate shall be inclusive of frame, shutter, vision glass (lead line glass), fastener, all hardware with installation for all floor all height etc complete as directed by engineer in charge. Out to out dimension of door with frame shall be measured for payment.

Providing and fixing 120 min fire rated Mortise sash lock of Dorma 281a or equivalent with 70 mm Cylinder Thumb turn with Lever TH 126 CE marked for fire rated metal door of Dorma or equivalent with necessary fittings etc. complete as recommended by manufacturer and as directed by Engineer in Charge.

VALVES WITHOUT INSULATION Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modulating control valve in a single body. The actuator shall be capable of accepting upto 10V DC and upto 20 mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm & above. Valves should have pressure rating of 25 Bar minimum. 80mm dia.