Public Works Department Tender

Disposing off the excavated stuff of above items for lead of (A) 50 m to 500 m

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates 20 mm nominal size) and curing complete excluding cost of formwork in (A) Foundation and Plinth

White Stone Bela mesonry block in course in superstructure with stone of approved quality in Cement Mortar 1:5 (1-Cement :5- course sand) including packing the joints etc. complete. Foundation and plinth

Filling in foundation and plinth with murrum or selected soil in layers of 20cm. thickness including watering, ramming and consolidating etc. complete. Out side of diu

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in © Slabs ,landing ,shelves ,Balconies, Lintels, Beams, Girders and Cantilever upto floor two level.

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in RCC wall

Providing and laying controlled cement concrete M.250 and curing complete excluding the cost of formwork and reinforcement for reinforced concrete work in (A) Foundations, footings, Base of columns and Mass concrete.

Providing formwork of Steel centering shuttering strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain concrete work in. (G) Columns PillarsPosts and struts. (1) Square Rectangular Polygonal in plan.

Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level

20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for interior plastering upto floor two level and finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand)

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering upto floor two level and finished even and smooth in (i)Cement mortar 1:3 (1-cement:3-sand)

Providing and applying exterior texture of approved shed and pattern rates are inclusive of one coat of white cement base putty, two coats of importade Archi Concrete material and asian paint base colour with required coats of asian texture paint rates are including scaffolding, all materials, labours and for any height.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Wall painting (two coats) with plastic emulsion paint With putty two coats and one coat primer of approved brand and manufacture on undecorated wall surface to give an even shade including throughly brushing the surface free from mortar droppings and other foreign matter and sand papered smooth.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and fixing factory made uPVC white colour glazed/Wire mesh window/door comprising of uPVC multi-chambered frame , sash and mullion/coupler extruded profiles having minimum wall thickness 1.70 mm for seris R1 and R2 profiles and 2.10 mm for series R3 and R4 profile conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing ade. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. (1)Using R4 Series with frame (64mm & above) x (50mm & above) & sash (64mm & above) x (70mm & above) & french (false) mullion (64mm & above) x (60mm & above). (Height above 1.8 Meter).

Providing and fixing flush door shutters solid core construction with frame of first class hardwood with cross board and face veneer or plywood face panels including anodised alluminium butt hinges with necessary screws. (B decorative typeand block board core s s butt hinges in flush door shutters (2) 35 MM thick

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20mm (average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on existing flooring by adhesive material including dismentaling of existing flooring and jointed with color cement slurry including finised with flush pointing & cleaning the surface etc. complete for DARK shade

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to bring mortar creme out upto surface using white cement including rounding off junctions and extending them upto 15 cm along the wall,clearing with water and oxalic acid etc. as directed.

Providing and fixing 65mm Thick M-30 vyara paver block of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Supplying, Erecting, Testing & Commissioning the PASSENGER AUTO LIFT (5 PASSENGER) TWO SIDE OPNEBANBLE IN DIFFERENT FLOORS MACHINE ROOM LESS having following main features: LOAD &SPEED 340 KG@1 M/SEC [1] GEAR LESS LIFT DRIVE comprising of High Starting torque Lift duty 3 phase 440 V A. C. Permanent magnetic synchronous motor of proper rating with high efficiency shall be used.[2] Micro processor based / V.V.V.F.ARD, vector control drive with encoder feedback closed loop system shall be used for lift car and door operation which shall be full collective selective operation hall call demand response, UP/DOWN hall stops, Main, Up/ Down Contactor with overload and phase reversal relay and safety controls. [3] Car with M S platform with bracings of adequate size and to sustain the impact load cabin + passenger with safety factor of fire for steel and side panels of Stainless steel of sheet of grade 304 duty. Car ceiling will be S.S. finishes with aesthetic appearance with LED ceiling lights. Car flooring shall be of anti skid PVC with choice of colour of engineer in charge. Car doors shall be of stainless steel grade 304, hairline finish with centre opening / telescopic automatic doors. Car panel will also be S.S. 304 finished with emergency stop device, mechanical door safety device, facility of auto/ attended mode. All car panel buttons and all floor switches must be with brail language as per lift act. MACHINE drectecly plaed above hoist way.HOIST WAY required 1700mm widex1420mm deep[4] All landing doors shall be fully automatic centre opening/ telescopic opening made of hairline finish steel grade of 304 with key holes and infrared curtains with Unlocking facility from outside. [5] Appropriate battery operated emergency light in the car along with alarm switch shall be provided. [6] Digital scrolling indicator system for up-down arrow along with floor position indicator shall be provided inside the car and at all floors. [7] Full height infra red curtain with multiple criss / crossing light beams shall be provided. [8] Automatic Rescue Device (ARD) shall be provided accordingly of passenger capacity. [9] Audio visual indication in the lift car showing over loading shall be provided such that doors kept open till excess load is removed. [10] Spring buffers/PU Buffers shall be provided. [11] Car fan with automatic sleep timer shall be provided. [12] Voice annunciater with suitable music shall be provided in lift car. [13] Self diagnostics system for operational and safety parameters shall be provided in control panel. [14] Mechanical over speed governor, door key holes in the floor doors, fireman switch shall be provided. . [16] In the hoist way fascia plate shall be provided without any extra cost, where ever required as / if directed by engineer in charge. [17] Permanent wiring in lift machine and lift well with proper numbers of light points, with fixtures, exhaust fan and plug points shall be provided by the agency. Power supply of 3 phase 440 V shall be made available by department in lift machine . [18] Any civil/ electrical works for additional and alteration in lift shaft and machine related to erection of lift shall be made by lift agency without any extra cost.(granite/marble fixing around all landing door openings are not in lift agency’s scope.) [19] Agency has to provide all working drawings and documents and liaison services for obtaining all necessary permission from lift inspector and other authorities. [20] As per statutory requirement of Got. Of Gujarat lift & escalator act 2000, lift agency has to provide 1. Car top safety barricade 2. Push & talk communication system. 3. Fireman's switch operation at Ground Floor (Make : Schinlder,Mitsubishi,OTIS,Kone,Prince) (I) 8/10 passengers . Ground plus 6 upper floors with Rated Speed of 1.0 m/sec with micro proce/PLC control and ACVVVF. drive..DRIVING ROPES USHA MARTIN/ORIENT/IMPORTED,MILD STEEL SHEETS:SAIL/JINDAL/IMPORTED LIFT TRAVEL GROUN FLOOR TO 2ND FLOOR ABOUT 12 METERS .CLEAR OPENING 700MMX2000M HEIGHT.CAR ENCLOSER:SS CABIN FINISH.SIGNAL:IN CAR:BATTERY OPERATED EMERGANCY LIGHT ,ALARM,DIGITAL FLOOR Two side opnable glass door INDICATION.AVAILABLE SIZE 1900MMX2100MM

Supplying, Erecting, Testing & Commissioning the PASSENGER AUTO LIFT 5 Passanger Lift) MACHINE ROOM LESS having following main features: LOAD &SPEED 340 KG@1 M/SEC [1] GEAR LESS LIFT DRIVE comprising of High Starting torque Lift duty 3 phase 440 V A. C. Permanent magnetic synchronous motor of proper rating with high efficiency shall be used.[2] Micro processor based / V.V.V.F.ARD, vector control drive with encoder feedback closed loop system shall be used for lift car and door operation which shall be full collective selective operation hall call demand response, UP/DOWN hall stops, Main, Up/ Down Contactor with overload and phase reversal relay and safety controls. [3] Car with M S platform with bracings of adequate size and to sustain the impact load cabin + passenger with safety factor of fire for steel and side panels of Stainless steel of sheet of grade 304 duty. Car ceiling will be S.S. finishes with aesthetic appearance with LED ceiling lights. Car flooring shall be of anti skid PVC with choice of colour of engineer in charge. Car doors shall be of stainless steel grade 304, hairline finish with centre opening / telescopic automatic doors. Car panel will also be S.S. 304 finished with emergency stop device, mechanical door safety device, facility of auto/ attended mode. All car panel buttons and all floor switches must be with brail language as per lift act. MACHINE drectecly plaed above hoist way.HOIST WAY required 1700mm widex1420mm deep[4] All landing doors shall be fully automatic centre opening/ telescopic opening made of hairline finish steel grade of 304 with key holes and infrared curtains with Unlocking facility from outside. [5] Appropriate battery operated emergency light in the car along with alarm switch shall be provided. [6] Digital scrolling indicator system for up-down arrow along with floor position indicator shall be provided inside the car and at all floors. [7] Full height infra red curtain with multiple criss / crossing light beams shall be provided. [8] Automatic Rescue Device (ARD) shall be provided accordingly of passenger capacity. [9] Audio visual indication in the lift car showing over loading shall be provided such that doors kept open till excess load is removed. [10] Spring buffers/PU Buffers shall be provided. [11] Car fan with automatic sleep timer shall be provided. [12] Voice annunciater with suitable music shall be provided in lift car. [13] Self diagnostics system for operational and safety parameters shall be provided in control panel. [14] Mechanical over speed governor, door key holes in the floor doors, fireman switch shall be provided. . [16] In the hoist way fascia plate shall be provided without any extra cost, where ever required as / if directed by engineer in charge. [17] Permanent wiring in lift machine and lift well with proper numbers of light points, with fixtures, exhaust fan and plug points shall be provided by the agency. Power supply of 3 phase 440 V shall be made available by department in lift machine . [18] Any civil/ electrical works for additional and alteration in lift shaft and machine related to erection of lift shall be made by lift agency without any extra cost.(granite/marble fixing around all landing door openings are not in lift agency’s scope.) [19] Agency has to provide all working drawings and documents and liaison services for obtaining all necessary permission from lift inspector and other authorities. [20] As per statutory requirement of Got. Of Gujarat lift & escalator act 2000, lift agency has to provide 1. Car top safety barricade 2. Push & talk communication system. 3. Fireman's switch operation at Ground Floor (Make : Schinlder,Mitsubishi,OTIS,Kone,Prince) (I) 8/10 passengers . Ground plus 6 upper floors with Rated Speed of 1.0 m/sec with micro proce/PLC control and ACVVVF. drive..DRIVING ROPES USHA MARTIN/ORIENT/IMPORTED,MILD STEEL SHEETS:SAIL/JINDAL/IMPORTED LIFT TRAVEL GROUN FLOOR TO 2ND FLOOR ABOUT 12 METERS .CLEAR OPENING 700MMX2000M HEIGHT.CAR ENCLOSER:SS CABIN FINISH.SIGNAL:IN CAR:BATTERY OPERATED EMERGANCY LIGHT ,ALARM,DIGITAL FLOOR INDICATION.AVAILABLE SIZE 1700MMX1700MM

Supplying, Erecting, Testing & Commissioning the (Service Lift) MACHINE ROOM LESS having following main features: LOAD &SPEED 340 KG@1 M/SEC [1] GEAR LESS LIFT DRIVE comprising of High Starting torque Lift duty 3 phase 440 V A. C. Permanent magnetic synchronous motor of proper rating with high efficiency shall be used.[2] Micro processor based / V.V.V.F.ARD, vector control drive with encoder feedback closed loop system shall be used for lift car and door operation which shall be full collective selective operation hall call demand response, UP/DOWN hall stops, Main, Up/ Down Contactor with overload and phase reversal relay and safety controls. [3] Car with M S platform with bracings of adequate size and to sustain the impact load cabin + passenger with safety factor of fire for steel and side panels of Stainless steel of sheet of grade 304 duty. Car ceiling will be S.S. finishes with aesthetic appearance with LED ceiling lights. Car flooring shall be of anti skid PVC with choice of colour of engineer in charge. Car doors shall be of stainless steel grade 304, hairline finish with centre opening / telescopic automatic doors. Car panel will also be S.S. 304 finished with emergency stop device, mechanical door safety device, facility of auto/ attended mode. All car panel buttons and all floor switches must be with brail language as per lift act. MACHINE drectecly plaed above hoist way.HOIST WAY required 1700mm widex1420mm deep[4] All landing doors shall be fully automatic centre opening/ telescopic opening made of hairline finish steel grade of 304 with key holes and infrared curtains with Unlocking facility from outside. [5] Appropriate battery operated emergency light in the car along with alarm switch shall be provided. [6] Digital scrolling indicator system for up-down arrow along with floor position indicator shall be provided inside the car and at all floors. [7] Full height infra red curtain with multiple criss / crossing light beams shall be provided. [8] Automatic Rescue Device (ARD) shall be provided accordingly of passenger capacity. [9] Audio visual indication in the lift car showing over loading shall be provided such that doors kept open till excess load is removed. [10] Spring buffers/PU Buffers shall be provided. [11] Car fan with automatic sleep timer shall be provided. [12] Voice annunciater with suitable music shall be provided in lift car. [13] Self diagnostics system for operational and safety parameters shall be provided in control panel. [14] Mechanical over speed governor, door key holes in the floor doors, fireman switch shall be provided. . [16] In the hoist way fascia plate shall be provided without any extra cost, where ever required as / if directed by engineer in charge. [17] Permanent wiring in lift machine and lift well with proper numbers of light points, with fixtures, exhaust fan and plug points shall be provided by the agency. Power supply of 3 phase 440 V shall be made available by department in lift machine . [18] Any civil/ electrical works for additional and alteration in lift shaft and machine related to erection of lift shall be made by lift agency without any extra cost.(granite/marble fixing around all landing door openings are not in lift agency’s scope.) [19] Agency has to provide all working drawings and documents and liaison services for obtaining all necessary permission from lift inspector and other authorities. [20] As per statutory requirement of Got. Of Gujarat lift & escalator act 2000, lift agency has to provide 1. Car top safety barricade 2. Push & talk communication system. 3. Fireman's switch operation at Ground Floor (Make : Schinlder,Mitsubishi,OTIS,Kone,Prince) (I) 8/10 passengers . Ground plus 6 upper floors with Rated Speed of 1.0 m/sec with micro proce/PLC control and ACVVVF. drive..DRIVING ROPES USHA MARTIN/ORIENT/IMPORTED,MILD STEEL SHEETS:SAIL/JINDAL/IMPORTED LIFT TRAVEL GROUN FLOOR TO 2ND FLOOR ABOUT 12 METERS .CLEAR OPENING 700MMX2000M HEIGHT.CAR ENCLOSER:SS CABIN FINISH.SIGNAL:IN CAR:BATTERY OPERATED EMERGANCY LIGHT ,ALARM,DIGITAL FLOOR INDICATION.AVAILABLE SIZE 1700MMX1700MM

Providing and fixing ms gate sliding / open with 12mm thick shera wood planks rate are inclusive of primer & oilpait etc complete

Providing and fixing PVC mosaic liner ,coping stone, filtration unit (2 nos), pump (2 nos), maintainance accessories 2 sets ( telescopic handle , vaccum hose, vaccum brush, wall brush, floor net, test kit, thermometer), start up chemical product (2 Set) Rates are inclusive of polish plaster, kundi for filtration unit, step, heating system 26 KW (2 nos), required platform fo heating system, all cutting in rcc works, making good the rcc work etc complete. for size(15.90m x 6.07m x1.2m)

Providing and fixing PVC mosaic liner ,coping stone, filtration unit (1 nos), pump (1 nos), maintainance accessories 1 sets ( telescopic handle , vaccum hose, vaccum brush, wall brush, floor net, test kit, thermometer), start up chemical product (1 Set) Rates are inclusive of polish plaster, kundi for filtration unit, step, heating system 26 KW (1 nos), required platform fo heating system, all cutting in rcc works, making good the rcc work etc complete. for sizze(5.65m x 4.07m x1.2m)

Providing fixing and commissioning sewage treatment plant with 10 kld capacity of underground FRP sewage tretment plant based on principle of aerobic attached growth membrane bio technology (MBR) domestic STP having external MB module along with interrumentations, pumping and blower equipment. all required civil and electric work shall be measured and paid separaely.

Providing and Fixing SS 304 Grade Balcony railing with glass railling horizontal pipes top and bottom c type 50mmx50mm and thoughend glass 12 mm thick Including Labour charges

Providing and Fixing SS 304 Grade Steel Stair railing balluster sss pipe (50 x 25 mm) handrail 50mm mid ral 16mm dia Including Labour charges

Structural steel work for pergola riveted, bolted or welded in built up sections, trusses andframed work, including cutting, hoisting, fixing in position and applying a primingcoat of approved steel Zinc Yellow primer And Oil Paint all complete.

Providing and fixing awning with frame & acreylic fabric and approved Weather Shed Onings

Providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more , of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : (4)Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

M-30 Providing & Laying Controlled cement concrete TRIMIX ROAD M-300 and curing complete including the cost of form work and Excluding reinforcement with c channel for shuttering work and hardner spreading on surface,Compact with floater machine, Channel Vibrator And self load mixer.

Supply & Installation of Akzonobal powder coated Aluminium Seishmec Rain screen Principal Continuous - Curtain wall Glazing system design to windstand 1.4 kpa a wind pressure.The fabricated System fixed on RCC structure at all level with mild steel powder coated heavy duty brackets with mechenical Anchore fastner & S.S. Nut, Bolt & Double washer. This system suitable for Single & Double glass. Other required accessories as per structural standard and per design & drawing

Providing and fixing 26.00 mm thick Double Glass Unit Consting of 8.0 mm thick ST Series Reflective H.S. + 12.0 mm Air Gap + 6.0 mm thick Clear H.S. Glass glass from Saint gobain Make with glass handlling & shifting of various floor and glass Breakage risk cover as under;

Providing and Fixing Supply & Installation of Akzonobal powder coated Aluminium Vertical Fin Size 50 mm X 150 mm wide with required suport with all stansdard accessories as under; Including labour with scaffolding

Providing and fixing Dorma make Automatic system for door without glass work ES 200 Standard including fixng

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 30cm length,30cm height and 15cm thick of M200 grade concret as per approved design and including excavation for fixing in proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc complete.

Providing and fixing aluminium louver of Jinadal with 2 mm thick blade size. Section includes concealed fastner, recessed flat seam metal louver system. Aluminium faced honey comb core louvers with integrated mounting clips. Rates are inclusive of sub structure for a complete installation on walls including vertical joint backing, mounting sub- girt, anchorages, shims etc complete. All MS fabrication will be measured and paid separately

Leather Finish Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 3 (1 cement : 3 coarse sand) : 25 mm thick