UT Administration Of Dadra And Nagar Haveli Tender

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [D] 32mm.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [E] 40mm.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of following dia. nominal bore tube fittings and clamps including making good the wall, ceiling and floor etc. complete. [F] 50mm.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing laying and jointing in true line and level 32mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing laying and jointing in true line and level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water including fittings make or equivalent as approved by Engineer In Charge. Pipe shall be fixed on the wall with the help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing, laying and jointing in true line and level 160 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI 14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints and jointed with adhesive solvent cement including cost of all materials.s per site eng.inch. /or eng./arch. approvals. ( Make:- Astral, Supreme, Finolex, Prince)

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(A) 100mm dia. (more than 10 ton)

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement Mortar in proportion 1:1 Selt glazed stoneware pipes including testing of pipes and joints complete.(B) 150mm dia. (more than 10 ton)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(A) 100 mm dia. (112 mm Ave.bed thickness)

Providing and laying Cement concrete 1:5:10 (1-Cement : 5-Fine sand :10-Graded stone aggregate 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(B) 150mm dia. (166mm Ave. bed thickness)

Providing and laying lime concrete 1:2:4 (1-Lime putty :2-Fine samd : 4-Graded brick aggregates 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(A) 100 mm dia. 300mm width (112 mm Ave.bed thickness)

Providing and laying lime concrete 1:2:4 (1-Lime putty :2-Fine samd : 4-Graded brick aggregates 40mm nominal size) bedding for stoneware pipes of following internal diameters with necessary formwork and curing complete.(B) 150mm dia. 450mm width (166mm Ave. bed thickness)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps. (A) 100mm x 100mm size P type. (upto 10 ton)

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps.(B) 150mm x 100mm size P or R type

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(B) 150mm (upto 10 ton) s per site eng.inch. /or eng./arch. approvals. ( Make:- Indian Hume Pipe, Pranali, or Eq.)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(C) 250mm (upto 10 ton) ( Make:- Indian Hume Pipe, Pranali, or Eq.)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(D) 300mm (upto 10 ton) ( Make:- Indian Hume Pipe, Pranali, or Eq.)

Providing laying (to level or slopes) and jointing reinforced concrete Light duty non-pressure pipes I.S. class NP2 of the following internal diameter with collars and butt ends prepared for collar joints including testing of joints complete.(E) 450mm (upto 10 ton) ( Make:- Indian Hume Pipe, Pranali, or Eq.)

Providing material and labour for Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (1) A type depth 0.90 Metre for 150mm diameter sewer.

Providing material and labour for Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for 150mm diameter sewer.

Providing material and labour for Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement :2-coarse sand : 4-graded stone aggregate 20mm nominal size) foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick bats 40 + 50mm size) inside plastering 15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size) finished smooth complete including curing and festing (i) Inside size 900mm x 1200mm and 1.5M. deep including C.I. cover with frame size 560mm diameter total weight of cover and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (3) C type depth 2.25 Metre for 150mm diameter sewer.

Providing material and labour for (A) With 230mm thick walls of brick msonry using brick having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse sand) (4) D type depth 3.15 Metre for 150mm diameter sewer.

Providing material and labour for (I) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part thereof over item No.24.27 (I) for depth from 0.9M to 1.5M.

Providing material and labour for (II) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. GR Part thereof over item No.24.27 (I) for depth from 1.50M. to 2.25M.

Providing material and labour for (III) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part thereof over item No. 24.27 (III) for depth from 2.25M to 3.15M.

Providing material and labour for(IV) Extra rate for constructing B.B. masonry for every additional depth of 0.1M. or Part thereof over item No. 24.27 (IV) for depth above 3.15M.

Providing material and labour for fixing cast iron steps of size 500mm x 150mm x 22.5mm and painting with two coats of Anti-corrosive paint etc. complete.

Providing material and labour for Supplying and fixing C.I. cover 300mm x 300mm without frame for Gulley trap (Standard pattern) te weight of cover to be not less 4.53 Kg.) (upto 10 ton)

Providing and erecting at the site of work steel ventilating column of 150m internal diameter and 12.20 Metre High from G.L. to bottom of top grill including C.I. grill and base plate bolts and nuts etc. and excavation in foundation of size 120cm. x 120vcm. x 165cm. and filling the pit with first layer of cement concrete 1:3:6 mix (1-cement :3-coarse sand :6-graded stone aggregate 20mm nominal size) of 120cm. x 120cm. x 90cm. and remaining pit with B.B.C. 1:3:6 mix (1-cement :3-coarse sand:6-Brickbats 40+50mm size) and providing fillet in Cement concrete 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm. nominal size) at G.L. and 3 coats of silver paint etc. complete.

Providing materual and labour for Constructing Brick masonry road gully chamber 500mm x 450mm x 600mm including 500mm x 450mm C.I. horizontal grating wih frame complete. (upto 10 ton)

Providing materual and labour for Constructing Brick masonry road gully chamber 450mm x 450mm x 775mm with vertical gating complete.

Providing materual and labour for Constructing brick masonry road gully chamber 1100mm x 775mm including 500mm x 450mm (C.I. horizontal grating with frame and vertical grating complete.) (upto 10 ton)

Providing materual and labour for Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line. (upto 10 ton)

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or two inlets. (upto 10 ton)

Providing materual and labour for Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete.(iii) Inside dimensions 600mm x mm and 450mm deep for pipe lines with three or more inlets.

Providing materual and labour for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i) for 455mm x 610mm size.

Providing materual and labour for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(ii) for 500mm x 700mm size.

Providing materual and labour for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(iii) for 600mm x 850mm size.

(A) Providing sock pit of 2.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (upto 10 ton)

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and filling brickbats with dry masonry work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 1:3 with finishing curing etc. complete as directed. (upto 10 ton)

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil

Providing and fixing Chlorinated Polyvinyl Chloride (CPVCSDR-11) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 75 mm nominal inner dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVCSDR-11) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge 100 mm nominal inner dia Pipes

Providing and supplying Gun metal chech, handle valve or non return full way wheel valve 80mm dia of PN1 (PD type short body) and diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges loading, unloading conveyance and fitting at site etc. complete.

Providing and supplying Gun metal chech, handle valve or non return full way wheel valve 100mm dia of PN1 (PD type short body) and diameter including all taxes, insurance, transportation, freight charges, octroi, inspection charges loading, unloading conveyance and fitting at site etc. complete.

HYDRO PNEUMATIC SYSTEMSupply, installation, testing & commissioning of VFD based Hydropneumatic system with FRP tank, pump-motor set, suction delivery valves & pipe, all instrumentation viz. Pressure switch, pressure gauge, level indicator, etc, starter panel (including one main pump & one trimmer pump VFD BASED ), cables, etc. FRP Hydropneumatic Tank with inter connection and suitable connections such as inlet, drain, outlet, pressure gauge, union connection, isolation valve, outlet pipe (to be connected to the header pipe), pressure switch, outlet valves, mounting pads, etc. with all accessories & as per the drawing. ( Groundfos, ITT Lowara, Make)'Supply, installation, testing & commissioning of online vertical booster pumps directly coupled with the motor with SS casing, SS impeller, SS shaft and driven by 415 V AC, 3 phase, 50 Hz.motor running at 2900 RPM speed and shall be supplied with all accessories viz. strainer / dry run protection/foot valve, base plate, coupling, etc.complete. The scope shall also include suction & delivery piping & valves. 15 m3/hr x 3 Nos. main Pumps at 45mtr. head. with 150 ltr. booster tank ( MAke :_ Groundfos, ITT Lowara or Eq. Make)

CENTRIFUGAL PUMPS,Suppying, installing, testing and commissioing of centrifugal monoset submersible pumps with c.i. casing, Bronze impeller, SS Shaft and driven by 415 V AC, 3 phase, 50HZ., motor running at 2900 rpm speed and shall be supplied with all accessories viz., base plate, coupling, motor, starter panel, cabling up to panel, dry ru protection, auto level sensor float switch operation,earthing,delivery & header pipes & valves etc., complete.. (UG tank to OHT feede and Softener Inlet Set ) ( Make Grundfos / ITT Lowara or Eq.)Capacity : 5.0 mtr3/hr. x 25mtr. head 1 working 1 stand by set.

BORE WELL TRUNKEY SYSTEM:-Supply installation, testing, commissioning of Bore well complete job, includin drilling 6" bore hole, casing pipe MS c-class, puming pipe tata-c class, testing of yeald test report, inlcuding water testing report, submersible pump to be installed in the tube well of required indicated capacity and head as per relevant IS for Bore water lifting with suitable submersible vet type, water cooled, squirrel case motor conforming to IS 9283, working of 3-phase, 50Hz +/- 3% 415 VAT +/- 10%, AC supply 2900 RPM synchronous speed with 10mtr. copper conductor flat cable from pump to starter panel with cables and termination ( all supports clamps pipe fittings mechanical seal, bearing, bush, strainer, etc. comp., Casing C.I., S.S. CF8M impeller, bronze casing, wearing and bearing bush, TC mechanical seal, S.S. bearing, S.S. shaft with sleeve, S.S. strainer, and M.S. morter along with water gurd, single phase preventor with all cables of appropriate size control and instrumentations, switches, testing, and installation along with testing. Comp Job Capacity of each pump set : (100 CU.MTR/DAY.)Depth : APPROX 600 to 900 ft.( It may very as per actual ground condition)

Construction of Percolation Well with all required connections as per detailed design and drawing.3mtr dia X 4 mtr lequid depth for cathbasin ( 150 r.mtr deep pipe-8" dia pipe)Note:- Configuration shall be provided by the contractor accoding to the bore hole data generated by CLINET .

Fire Protection:-Supply, installation, testing & commissioning of electric driven Hydrant & Sprinkler Pump suitable for automatic operation consisting of the following:a)Horizontal end suction centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump b)Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.c)Common bed plate of fabricated mild steel channel or cast iron type.d)Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. The pump shall be of the following specifications:Discharge - 2280 lpm Head - 70 mtr No. of stage preferred - Single / Double Speed RPM - 2900 Material of construction a) Impeller - Bronze b) Casing - C.I. c) Shaft & Shaft Sleeve - SS-410 d) Bearing - Grease Lubicated e) Seal & Make - Mechanical Type of pump - End suction

Supply, installation, testing & commissioning of electric driven Jockey Pump suitable for automatic operation consisting of the following: Horizontally mounted centrifugal end suction pump complete with mechanical seal and including necessary arrangement for testing of pump.Squirrel cage induction motor suitable for 4440 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.Common bed plate of fabricated mild steel channel or cast iron type.Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. The pump shall be of the following specifications:Discharge - 180 lpm,Head - 70 m No. of stage preferred - Multistage ,Speed RPM - 2900,Mover - Electric Motor Driven,Material of construction a) Impeller - Bronze b) Casing - C.I.,c) Shaft & Shaft Sleeve - SS-410,d) Bearing - Grease Lubicated,e) Seal & Make - Mechanical,Type of pump - End suction

Supply, installation, testing & commissioning of diesel engine Hydrant Pump suitable for automatic operation consisting of the following: Horizontal split casing centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump,Water cooled Diesel Engine developing suitable BHP at 1500 RPM for the Pump, common bed plate for mounting of engine and pump, RCC foundation and vibration damping arrangement by Cushy Foot and engine panel provided by engine manufacturer, connection to Engine Starting Panel as per item (4), sealed maintenance free batteries of 24 V, 88 AH. Rate shall include Exhaust pipe of required length with asbestos lagging, muffler, day oil tank of 400 lts with first charge and manual oil pump set.Flexible coupling and coupling guard with the Pump,Common bed plate of fabricated mild steel channel or cast iron type.Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. Sealed maintenance free batteries of 24 V, 88 AH --2 Nos. (1 working + 1 standby),Exhaust pipe of required length with asbestos lagging, muffler,Day oil tank G.I. Metal) of 400 lts with first charge and manual oil pump set and necessary piping and structural work to place tank at upper level from pump in pump room,The pump shall be of the following specifications:Discharge - 2280 lpm,Head - 70 m,No. of stage preferred - Single / Double,Speed RPM - 1450,Mover - Diesel engine driven,Material of construction ,a) Impeller - Bronze,b) Casing - C.I.,c) Shaft & Shaft Sleeve - SS-410,d) Bearing - Grease Lubicated,e) Seal & Make - Mechanical,Type of pump - END SUCTION

Supply, installation, testing & commissioning of electric driven automatic fire booster Pump suitable for automatic operation consisting of the following: Horizontal end suction centrifugal pump complete with mechanical seal and including necessary arrangement for testing of pump.Squirrel cage induction motor suitable for 415 V, 50 Hz, AC supply of suitable rating for the above pump with synchronous speed of 2900 RPM T.E.F.C. type and conforming to IP:55 and flexible coupling and coupling guard with the pump.Common bed plate of fabricated mild steel channel or cast iron type.Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. The pump shall be of the following specifications:Discharge - 900 lpm,Head - 40 m,No. of stage preferred - Single / Double,Speed RPM - 2900,Material of construction ,a) Impeller - Bronze,b) Casing - C.I.,c) Shaft & Shaft Sleeve - SS-410,d) Bearing - Grease Lubicated, e) Seal & Make - Mechanical,Type of pump - End suction,f) H.P. --

Providing and fixing air vessel for fire pumps as per following specifications:Diameter - 450mm,Shell thickness - 8mm,Dish ends - 10mm,Height - 1500mm,Finishing - Two coats of Red enamel paint of first grade over one coat of primer externally & two coats of epoxy coating inside,Material of Construction - M.S.,Test Pressure - 15 Kg./sq.cm.

Fire Fighting Panel:-Supply, installation, testing & commissioning of cubical type, dead front, 2.0mm thick CRCA sheet steel enclosed, free standing indoor type extendible Fire Fighting panel with vermin proof hinged lockable doors for each compartment provide bus bar interconnections for incoming and outgoing including feeders earthing and paint shade as per Fire norms and as per specifications.out going motor feeders to have start/stop on / off /trip indication and current in all the phases. All out going terminals brought to cable alleys. This panel should be painted in Red shade as per local Fire Officer's norms, if any.One incoming 630 Amp TPN MCCB 35kA volt metre, volt metre selector switch and indicating lights, Ammeter for three phases.315 Amp. TPN MCCB 35kA feeder-2 Nos,63 Amp. TPN MCCB 35kA feeder-2 Nos,32 Amp. TPN MCCB 35kA feeder-1 No.,Automatic DOL starter feeders suitable for Hydrant Pump motor (75 KWs with O/L RELAY, Timer, Push Buttons & Auto-manual switch.-1 Nos,Automatic direct on line starter feeders suitable for jockey Pump (15 KW motor with O/L relay push Buttons and Auto-manual switch.-2 Nos,Automatic direct on line starter feeder suitable for Booster Pump (5.5 KW motor with O/L relay push Buttons and Auto-manual switch.-1 No,Fully automatic diesel engine starting system feeder complete with battery charger, Hooter, indicating lights, Transformer, Rectifier, Timer, Voltmeter, Ammeter, Selector Switches, Push Buttons, Anxillary Relay etc. complete as required. For 12 volts system,Providing, fixing, testing and commissioning of 1/2 Km. Range Siren with required cable.Operating Sequence for the Fire Fighting System,The operating pressure in the mains is to be maintained at 7.0 kg/cm2.,The jockey pump shall start automatically the moment pressure drops to 6.5 kg/cm2 because any leakage or minor draw-off from the system and stop when the pressure reaches 7.0 kg/cm2 again.In case, after the start of jockey pump, the pressure still keeps on falling, the main fire pump shall start at 6.0 kg/cm2 by triggering of the pressure switch. Jockey pump shall stop when main pump starts.,In the event of electrical or mechanical failure of main fire pump (hydrant) to start, the diesel engine driven pump shall cut in when the pressure in the mains fall down to 5.5 kg/cm2. The main electric pump shall then be locked out.,In the event of failure of wet riser system, there will be further drop in pressure and when the pressures reaches to 5.0 kg/cm2 fire booster pump near overhead tank will start automatically.,If within a preset period the standby pump fails to start or fails to develop adequate pressure, the control system shall shut down the standby pump and lock it out and given an audiovisual indication to that effect at the control panel.,Jockey pump shall be shut down automatically when the fire pump electric or diesel, is operating. Necessary integration of pipe work and controls shall be provided for the purpose. A timer may be employed where necessary to distinguish between slow fall of pressure due to system leaks and sudden fall of pressure due to fire duty by opening of valves and thus prevent parallel start up of both pressurization and fire pumps.,The control panel shall have status selection for each of the pumps for “automatic” as well as “manual” operation.,Pumps when under “manual” status shall be operated manually through relevant push buttons.,The fire pumps once started shall not be stopped automatically.,The fire pumps shall be locked out for operation both for “manual” and “automatic” operations, once the low water controls operates and furnish an audio and visual alarm on the panel the audio alarm can be silenced by accepting the alarm. The visual alarm shall be individual for each equipment. It shall be flashing type and on acceptance remain steady. A reset button shall be provided for each pump for returning the pump for fire duty.,Over load or under voltage/no volt trip devices for electric fire pump shall not be provided in the starter. LED type indication lamps to indicate the availability of power shall be provided.Once tripped the electric fire pump shall remain locked out for operation irrespective of the position of its operational status selection switch. Look out indication shall be available on the panel.,Return to normal operational availability shall be feasible only by manual re-set of locked out units by operation of appropriate push buttons.When fire pumps are brought into operation an audible tone from turbine type alarm operated by water flow in the mains shall be provided to indicate the healthiness of the system. The healthy running alarm shall not be silenced till the fire pump is shut down, but the tone may be mellowed by the operation, if required.Alarm for failure and lock out of any pump shall distinct from “healthy” alarm. Failure alarms shall be loud and can be silenced on acceptance.Repeat indication of various audio and visual indications on a slave remote panel in fire control room in terminal building shall be available. The slave Remote panel shall have indication lamps to show the status of :,a) Power healthy in fire pump room.b) Jockey pump ‘ON’,c) Main pump ‘ON’,d) Fire booster pump ‘ON’,The slave Remote panel shall also have a hooter, which shall sound in case, any pump is ‘ON’. The slave Remote panel shall have a provision to reset the hooter with the help of a push button..

Providing and laying the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor 3 core x 95 sq.mm

Providing and laying the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor 3 core x 10 sq.mm (cable from pump room to terrace for booster pump)

Providing and laying the PVC insulated & sheathed FRLS Armoured cables of 1.1 K.V. Aluminium Conductor 3 core x 16 sq.mm (cable for jockey pump)

Providing and fixing in position cable end termination glands for above mentioned cables 3 core x 95 sq.mm

Providing and fixing in position cable end termination glands for above mentioned cables 3 core x 10 sq.mm (cable from Booster Pump to terrace Remort Panel )

Providing and fixing in position cable end termination glands for above mentioned cables 3 core x 16 sq.mm (cable for jockey pump)

Providing, installation, testing, & commissioning of Remote Panel for fire fighting terrace pump with push buttons for manual operation (the remote panel shall be located at ground level) all complete.

Supplying, laying and connecting of following size 1.1 kV grade copper conductor armoured control cable on wall or on existing cable tray with clamping, dressing or drawn in existing ducts all as required (For remote panel for fire fighting terrace pump).3 core x 6 sq.mm

Providing, installation, testing, & commissioning of pressure switches for Hydrant, Sprinkler, Standby and Jockey pump including necessary wiring upto control panel & other materials.

Providing and fixing fire retardent / extinguishing electrical insulated synthetic mat of 5mm thick ±10% conforming to latest BIS doc no.-ET-02(5440) meeting requirements of IS 3043 / IS 5216 (Part I, II & III), IS 8437 & IEC 479 suitable for all voltages not exceeding 3.3 KV AC supply and having minimum width of 1000mm ± 20mm and including supply of required quantity of adhsive / compound and fixing the same at site as per site requirement.

Fabricating and installing following size of perforated G.I.cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders including painting, etc., as required.150mm width x 50mm depth x 1.5 mm thickness.

Providing & fixing 25 mm x 5 mm G.I. Strip in on surface or in recess for connections etc as required.

Providing & fixing 25 mm x 5 mm G.I. Strip in 40 mm dia GI pipe from earth electrode as required.

SUCTION AND DELIVERY PIPES AND VALVES FOR FIRE FIGHTING PUMPS :-Providing and fixing M.S. suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting M.S. pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation.15 mm nominal bore

Providing and fixing M.S. suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting M.S. pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation 25 mm nominal bore

Providing and fixing M.S. suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting M.S. pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation 80 mm nominal bore

Providing and fixing M.S. suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting M.S. pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation 100 mm nominal bore

Providing and fixing M.S. suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting M.S. pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation 150 mm nominal bore

Providing and fixing M.S. suction & delivery headers / pipes for fire fighting pumps (IS. 1239 heavy duty) including all fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete alongwith painting M.S. pipe with coat of Red Oxide primer and two or more coats of synthetic enamel paint of approved colour and quality to give an even shade including surface preparation 200 mm nominal bore

Providing and fixing cast iron wafer type Butterfly valve of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications.80 mm nominal bore

Providing and fixing cast iron wafer type Butterfly valve of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications.100 mm nominal bore

Providing and fixing cast iron wafer type Butterfly valve of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications.150 mm nominal bore

Providing and fixing cast iron wafer type Butterfly valve of the following size complete with bolts, nuts, washers and neoprene gaskets as per specifications.200 mm nominal bore

Providing and fixing cast iron dual plate wafer type non return valves. 80 mm nominal bore

Providing and fixing cast iron dual plate wafer type non return valves. 150 mm nominal bore

Providing and fixing cast iron dual plate wafer type non return valves. 200 mm nominal bore

Providing and fixing reinforced Neoprene flexible pipe connectors with all accessories on all pumps delivery. Suitable for 20 Kg/cm2 80mm

Providing and fixing reinforced Neoprene flexible pipe connectors with all accessories on all pumps delivery. Suitable for 20 Kg/cm2 150mm

Providing and fixing of nickel plated brass / nonferrous alloy fullyway ball valve (minimum working pressure of 20 bar ) with operating handle of approved make.25 mm nominal bore

Providing and fixing of nickel plated brass / nonferrous alloy fullyway ball valve (minimum working pressure of 20 bar ) with operating handle of approved make.15 mm nominal bore

FIRE HYDRANT SYSTEM(External & Internal)(All Fire Fighting Hardware Should be ISI Mark):-Providing and laying of M.S. pipes confirming to IS. 1239 Heavy duty including all GI/MS fittings like couplings, bends, elbows, offsets, blind flanges, plugs, tees, flanges (flanges as per table E), etc. threaded or welded (all type ) joints as per detailed specfications as required, cutting holes and chases in brick or RCC walls or floors and making good complete with one coat of 4 mm thick 'PYPKOTE' or COATEK anti rust pipe protection including approved primer & surface preparation of pipes as per manufacturers specifications and lap of 25 mm to make an impermeable layer on MS pipes in trenches or underground pipes below soil all complete. Under ground 150 mm dia

Painting for M.S. pipe with a coat of red oxide primer and two or more coats of synthetic enamel paint of approved colour and Quality to give an even shade including surface preparation. 150mm dia

Providing and fixing gunmetal fire brigade inlet head as per IS:904 Specification tested for 20 Kg/cm2 with 63 mm dia instantaneous type inlet and 150mm dia. flanged outlet with built-in check valve for fire brigade connection to under ground tanks and fire risers including campanion flanges as pertable " E" including nuts, bolts & washers etc.Four way

Providing and fixing gunmetal fire brigade inlet head as per IS:904 Specification tested for 20 Kg/cm2 with 63 mm dia instantaneous type inlet and 150mm dia. flanged outlet with built-in check valve for fire brigade connection to under ground tanks and fire risers including campanion flanges as pertable " E" including nuts, bolts & washers etc. Two way

Providing and fixing suction coupling for fire brigade drawl of water from tank with 150 mm dia GI (Medium) pipe and foot valve

Providing, fixing ,testing and commissioning external (yard) hydrant "STAND-POST" type conforming to IS:908-1975 and comprising of stand post for single outlet of hot diped class ' C' G.I. Pipe of 100 mm dia at the with instantaneous spring lock type Stainless steel female coupling of 63 mm dia for connecting to hose pipe, single headed SS valves conforming to type A of IS: 5290-1977, GI tee tapping from underground mains, flange riser and any other accessories etc. as per specification complete as required.

Providing and fixing fire hose cabinet fabricated from 16 gauge M.S.sheet with locking arrangement and hanging arrangement for accessories painted "Fire Red" with Stove enameled paint "Fire Hose" written on front including suitable supports to place 900 mm above ground level properly anchored, approximately size 800 X 600 X 250 mm deep (to house two lengths of canvas hose with couplings, branch pipe with nozzle for external hydrants) FOR EXTERNAL.

Providing and fixing cast iron following size complete with bolts, nuts, washers and neoprene gaskets as per specifications. 200mm dia y strainer in main suction header

P/ F PCC foundation for fire pumps as required for Electric driven fire pump

P/ F PCC foundation for fire pumps as required for diesel driven fire pump

P/ F PCC foundation for fire pumps as required for jockey pump

Costing for Liasion work with authority and obtaining NOC and all relevant applicable approvals including required drawing work.

SHRUBBERY/HEDGE PLANTATION (25-30plants/M2, 1' height) :Supply & plantation of shrubbery plants (To be planted in garden soil over already dressed area ) development of bed, cultivation soil mixture and plantation of shrubbery (as per plantation plan provided). Pesticides application to be done as per requirement, application of soil additive @ 5kg per M2 etc. Complete as directed by engineer-in-charge.

Providing material and labour for making GRANITE Having 16mm to 18mm thick (Locally available) stone over 10 mm thick cement plaster (1 cement :3 sand) jointed with cement slurry including making molding to edge of stone slab as directed by engineer in charge.

Supply, installation and testing of Drip on Line Lateral Pipe 16 mm X 4kg , 4 LPH, 45 cm (Brown) of make Rainbird/Toro/Nelson as per all the instruction given by the Architect and directed by the Engineer-in-charge

Carriage of Good earth as per all the instruction given by the Architect and directed by the Engineer-in-charge

Demolition including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift. (i) R.C.C. work

Demolition of Brick work and stone masonry including stacking of serviceable materilas and disposal of unserviceable materials with all lead and lift.(ii) In Cement Mortar

Preparing structural design of RCC Under Ground / Partially under ground / above high ground level Reservoir litres capacity as per relevant I.S.s and constructing the same, including excavation in all types of soil strata (including rock) including shoring strutting if required, for loose soil / to protect from collapse due to near by traffic load, casting 100 mm thick P.C.C. levelling course in M-10, Refilling the pit with proper soil and disposing of the surplus stuff within a lead of 50 meters. Including cement plaster in CM 1:2 with approved water proofing compound to inside water touching surface to container. Including all types of labour and material charges of lowering, laying, erecting / hosting and jointing of pipe assembly to inlet, outlet overflow, washout and bye pass arrangement as per hydraulic design. Providing and fixing accessories like MS / GI Ladder, CI Manhole frame and cover, water level indicator, adequate cowl type ventilators or lantern type ventilator with stainless steel jail. B.B. Masonry chambers for valves. Providing and applying three coats of cement paint / snowcem to the out side face of structure. It also includes satisfactory water tightness test as per relevant I.S. code and painting name of scheme and capacity on the tank as per direction of engineer in charge. List of Indian Standards for Design of GSR / SUMP:- The structural design of GSR shall be in accordance with provisions relevant I.Ss. (1)     I.S. 3370, Part – 1 to 4, 2009 or latest revised. 1.1) I.S. 3370 part III & IV 1965 or latest revised (2)     I.S. 456 – 2000 or latest revised. (3)     I.S. 1893 – 2000 – 1984 or latest revised. (4)     I.S. 875, Part – 1 to 3, 1987 or latest revised.

Providing and stacking of Red Machera of height 120 - 150 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Travel Palm of height 210 -240 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Chistina fiscus of height 100 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Golden Fiscus of height 100 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Parijat of height 120 - 150 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Thuja of height 100 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Foxtail Palm of height 270 - 300 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Sopari of height 270 - 300 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Colathea Lutea of height 120 - 150 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Peace lily of height 30-45 cm.in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Merenda Cobra of height 30-45 cm.in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Madhukamini Dwarf of height 60-75 cm.in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Alba champa of height 150-210 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Royal palm of height 210 -240 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Prismarkha Palm of height 150-210 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Sapothia Palm of height 120-150 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Alocasia of height 90-150 cm.in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Phonix palm of height 100 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Aereca Palm of height 150 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus Panda of height 1001 cm.in earthen pots of size 25 cm as per direction of the officer-in-charge.

Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass with company mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD 10 %, CCT 3000 K to 5700K,Uniformity ratio 0.45, Luminaire efficacy 100 lumens/watt . LED driver efficiency 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) (A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with over-voltage protection. (i) above 36 to 48 watts. Cat-III

Supply of approved make FRP Pole having following specifications: FRP Light Pole made by CNC filament winding machine using thermoset resin polyester/epoxy resin system) having minimum 62% glass content. The pole should be in one piece and tapered round in shape, having smooth finish and should be totally free from corrosion as well as non conductive & shock proof Pole should be provided with FRP Anchor Base and it should be heavy duty, or MS Material duly painted with Epoxy paint. Pole should be flame retardant as per IS 6746. Resin used shall be UV resistance and pigmented. A highly weather resistant polyurethane coating shall be applied to the pole after applying suitable primer system that ensures proper adhesion of the paint. Minimum coating thickness shall be 80 to 100 micron. Deflection of the pole shall not exceed more than 10% of the length of pole for the given load“ Pole should be generally made as per the dimensional data, performance criteria and some interchangeability features of poles as per standard ANSI C 136.20 latest version or ASTM D 4923/01 including cable termination box with necessary accessories . The size of pole and type of installation with foundation as per manufacturer details and site requirement are as below . (1) Suitable for base plate mounting single arm Bracket. [H] Overall length of 6 Mtr. Average Thickness: 7.5mm Top/ Bottom OD Dia A/F 89mm ± 2mm approx. approx. Weight of Pole 32 kg approx. (Without Base) Anchor Base (Size 300X300 & 18mm Th.)

Providing FRP arm bracket of having 2 sets of suitable SS304 hardware for fixing the brackets & spread of 1.2 Mtr(Suitable for 89 to 114 mm pole top dia) (A) Single arm bracket

(c) LED Bollard fittings of minimum height 1000 mm & dia.100mm having polycarbonate clear/milky diffuser mounted on 3mm thick aluminium finished powder coated pipe with base plate 160x160mm with erection by M8x75mm fastner with required RCC foundation.IP65 for 18watt and above ,surge-4kv cat-III

Providing material and labour for structural steel work (confirming to IS 4923-1997 ) riveted, bolted or welded in builtup for all type sections in framed work for Grills, Gates, etc, including Profile cutting, smooth grinding/machining of edges/faces/ all welding joints, Necessary welding, machine drilling of holes for joining/ anchoring, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per the structural designs and drawings and as directions of engineer n charge complete. Standard measurement will be paid for as actual cut length used at site.

Providing Material and Labour for fixing Louveres of Aluminium anodized aluminium sections as horizontal members at 75 mm c/c and 100 x 25 aluminium vertical section 125x25 mm fixing and erection on site and making surface good etc. complete as per design

Providing SS Name plate in rooms of all building as instructed by Engineer-in-charge, 150mm x 250mm.

Providing Direction Signages in all building as instructed by Engineer-in-charge on Acylic plate of size 600mmx600mm.

Providing Permanent room number as instructed by Engineer-in-charge of sticker of diameter 150mm.

Providing School Name board (exterior main Gate) as instructed by Engineer in charge on steel letter/channel letter of size 1200mmx900mm.

Providing Good thought in school Lobby area as instructed by Engineer in charge on PVC board with lamination & frame of size 900mmx200mm.

Providing National leaders, social reformers & freedom fighter photo frame as instructed by Engineer in charge on PVC board with Glass frame of size 330mmx400mm.

Providing Inspirational frames in activity room of school buildings including swachta postures,save water. as instructed by Engineer in charge on PVC board with lamination & frame of size 600mmx600mm.

Providing Inspirational frames in Toilet area room of school buildings including swachta postures,save water.as instructed by Engineer in charge on PVC board with lamination & frame of size 400mmx400mm.

Providing Wall beautification including courtyard area & preschool classroom .as instructed by Engineer in charge. One job

Providing Beautification of entrance wall in building as instructed by Engineer in charge. One job

Providing Saraswati Maa murti as instructed by Engineer in charge of white Marble of Standard Quality of 5 feet.

Felling trees of the girth (measured at a height of 1 m above ground level ), including cutting of truncks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 30cm girth upto and including 60 cm girth.

Felling trees of the girth (measured at a height of 1 m above ground level ), including cutting of truncks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. Beyond 60cm girth upto and including 12000 cm girth.

Providing and fixing eco-friendly light weight calcium silicate false ceiling tiles having Tegular edge & 15 mm Thick Densified edges on the Tile Periphery for Extra Strength The Light weight calcium silicate ceiling tiles shall have , light reflection 85% non-combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity0.043° w/m KC.for the best thermal Insulation . The Light weight calcium Silicate tile shall be of approved texture Fine fissured/ Spintone/Cosmos having NRC value of 0.5 & Globe having NRC value of 0.75 NRC or equivalent of size 595 X 595 mm to be laid on true horizontal level suspended inter locking metal grid of hot dipped galvanized steel sections (galvanizing @120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and size of 24X38mm made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross ‘T’ of size 24X28mm made out of 0.33mm (Minimum) sheet spaced 1200mm along spaced between main ‘T’ at 600mm centre to centre to form agrid of 1200X600mm and secondary cross ’T’ of length 600mm and size 24x28mm made of 0.30 mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of size 600X600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size (24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick Densified edges light weight calcium silicate ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in the grid including, cutting /making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required, Main

fixing single layer water proof gypsum board 12.5 mm thick sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm suspended by GI suspender channel of size 25 mm x 3 mm with intermediate channel og size 18 mm x 40 mm x 0.8 mm at 1220 mm center to center ceiling section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter channel A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops incl.paper tap sand sofit cleat, anchor fastener, scoch bolt connecting cleat,joining compound top coat on ceiling incl.making necy.opening for light fitting,diffuser etc. comp. as per detail drawing as directed