UT Administration Of Dadra And Nagar Haveli Tender

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (c) One wire 2.50 sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables, (F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in existing trench / pipe of following size of cables, (B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

Providing & laying approved make Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II )with necessary connecting accessories of same material at required depth in existing trench for laying of cable. below ground / road surface for enclosing cable, (A)50 mm outer dia

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (B) 3 & 1/2 core 35/50 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type cable gland with rubber ring for PVC insulated armoured cable complete with out going tails, insulating tape etc for following size of cables. (E) 3 & 1/2 core 120 Sq. mm

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (D) 35/50 Sq.mm.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (G) 120 Sq.mm.

Supply, installation, testing and commissioning of Distribution Panel as per Specification, Technical Data sheet, IS & relevant drawings. The panel manufactured shall be CPRI certified (for 25kA in last two years) panel manufacturer with RAL-7032/7035- Powder coating, in house 7-tank chemical process and painting facility. The unit rate for each item shall include :1) Testing of panels as per specifications at manufacturer's works in presence of client's representative and/or consultant. 2) Delivery of the panel to site. 3) 'Shifting of the panel from site store to the suitable location.4) Assembly and wiring of component supplied separately. 5) 'Installation of panels as per Location arranged by site Engineer in charge including removing packing. 6) Earthing all components, frame etc. to a common internal earth bar.7) Touching of body with powder coating for damaged parts. All the nuts bolts & joints exposed to the air shall be covered with suitable anti - oxtidant material or as directed by the Engineer incharge.8) Supply and fixing all accessories and supporting structure. 9) 'Checking of Internal connection & wiring, operation of switches, MCCB, MCB etc. 10) Supply of necessary tools, hardware, testing hardware, testing equipment during testing at site. with inclusive controlling components of, Main distribution Panel with 1 Nos of I/C feeder of rated 200 Amp 4P 50 KA, MCCB, (make:Schneider/L&T), 02 Nos Red LED indicators of 22.5 mm, 240V AC operating, 1 nos Green LED indicators of 22.5 mm, 1 Nos yellow LED indicators 22.5mm, 1 Nos Amber LED indicators 22.5 mm, 1 Nos Blue LED indicators 22.5 mm of( make:ESBEE), 06 Nos of 6A 1P, 10 KA C-Curve MCB type XC60, 1 Nos of Multifunction meter -Load manager with RS485 port, parameters:V, A, F, PF,W/VA, WH/VAh, Runhrs, Onhrs & interupts & Suppression Current (5 to 99 mA), Acc.CI 1.0, 3ph operating voltage: 80 to 480 V AC, Size:96 X 96, model:EM6436H, 04 Nos 200/5A, Acc.CI:tape insulated Ring type Current Transformer, ID:130mm, 1Nos 10 A Auxillary contactor, AC coil, Contacts2NO+2NC type:K model, 1 Nos of SSP+ selectable under voltage+selectable over volatage relay, selectable OFF Delay 15 sec & ON Delay 5 sec, Phase 10% Asymmetry, voltage: 415 VAC, 2 C/O, 3Phase,3W, Type:SM501. with 03 Nos of O/G feeder of rated 63 Amp, Four pole MCB, 25 KA, (make:Schneider/L&T/Siemens or equivalent), with 8 Nos of O/G feeder of rated 32 Amp, Double pole MCB, 25 KA, (make:Schneider/L&TSiemens or equivalent).

Supply, installation, testing and commissioning of Distribution Panel as per Specification, Technical Data sheet, IS & relevant drawings. The panel manufactured shall be CPRI certified (for 25kA in last two years) panel manufacturer with RAL-7032/7035- Powder coating, in house 7-tank chemical process and painting facility. The unit rate for each item shall include :1) Testing of panels as per specifications at manufacturer's works in presence of client's representative and/or consultant. 2) Delivery of the panel to site. 3) 'Shifting of the panel from site store to the suitable location.4) Assembly and wiring of component supplied separately. 5) 'Installation of panels as per Location arranged by site Engineer in charge including removing packing. 6) Earthing all components, frame etc. to a common internal earth bar.7) Touching of body with powder coating for damaged parts. All the nuts bolts & joints exposed to the air shall be covered with suitable anti - oxtidant material or as directed by the Engineer incharge.8) Supply and fixing all accessories and supporting structure. 9) 'Checking of Internal connection & wiring, operation of switches, MCCB, MCB etc. 10) Supply of necessary tools, hardware, testing hardware, testing equipment during testing at site. with inclusive controlling components of, Main distribution Panel with 1 Nos of I/C feeder of rated 125 Amp 4P 50 KA, MCCB, (make:Schneider/L&T), 02 Nos Red LED indicators of 22.5 mm, 240V AC operating, 1 nos Green LED indicators of 22.5 mm, 1 Nos yellow LED indicators 22.5mm, 1 Nos Amber LED indicators 22.5 mm, 1 Nos Blue LED indicators 22.5 mm of( make:ESBEE), 06 Nos of 6A 1P, 10 KA C-Curve MCB type XC60, 1 Nos of Multifunction meter -Load manager with RS485 port, parameters:V, A, F, PF,W/VA, WH/VAh, Runhrs, Onhrs & interupts & Suppression Current (5 to 99 mA), Acc.CI 1.0, 3ph operating voltage: 80 to 480 V AC, Size:96 X 96, model:EM6436H, 04 Nos 125/5A, Acc.CI:tape insulated Ring type Current Transformer, ID:130mm, 1Nos 10 A Auxillary contactor, AC coil, Contacts2NO+2NC type:K model, 1 Nos of SSP+ selectable under voltage+selectable over volatage relay, selectable OFF Delay 15 sec & ON Delay 5 sec, Phase 10% Asymmetry, voltage: 415 VAC, 2 C/O, 3Phase,3W, Type:SM501. with 03 Nos of O/G feeder of rated 32 Amp, Four pole MCB, 25 KA, (make:Schneider/L&T/Siemens or equivalent), with 5 Nos of O/G feeder of rated 32 Amp, Double pole MCB, 25 KA, (make:Schneider/L&TSiemens or equivalent).

Supplying & erecting funnel type earthing having earth plate of following size burred in specifically prepared earth pit 3 mtr. below ground with 40 kg. charcoal and salt with alternate layers of charcoal & salt, 20mm.dia. G.I. pipe with Funnel with a wire mesh for watering & bricks masonry block, C.I. Cover complete as per para 7.3 of IS 3043 with necessary length of double Galvanised Iron / copper earth wire No 6 SWG bolted with lug to the plate and covered in 12 mm dia. G.I. pipe 2.5 mtr long complete connected to the nearest switch gear with end socket as per direction & duly tested by earth tester confirming to IS (As per drawing) with following specification. (B) With 45 x 45 x 0.35 cms. C.I. earth plate

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using proper clamp.