Urban Administration And Development Tender

Supply and fixing of precoated galvanized iron profile sheets (size, shape
and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/-
5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in
240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet
and polyester top coat 15-18 microns. Sheet should have protective guard
film of 25 microns minimum to avoid scratches while transportation and
should be supplied in single length upto 12 metre or as desired by
Engineer-in-charge. The sheet shall be fixed using self drilling /self
tapping screws of size (5.5x 55mm) with EPDM seal or with polymer
coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I.
limpet washers or with G.I. limpet washers filled with white lead complete
upto any pitch in horizontal/ vertical or curved surfaces excluding the cost
of purlins, rafters and trusses and including cutting to size and shape
wherever required.

Steel work in tubular (round, square or rectangular hollow tubes etc.)
structure in built-up sections, trusses and frame work including cutting,
hoisting, fixing in position upto a height of 5m above plinth level,
consisting of columns trusses, roof and bottom purlins, base plate, holding
down bolts, wind ties bracing (if required), bolts, nuts and washers for
fastening etc. complete with applying a priming coat of red oxide zinc
chromate primer.

Providing and fixing steel door/ window with M.S. sheet 1mm thick, frame
of angle iron, diagonal braces of angle/ flat iron of suitable size, 3.00 mm
M.S. gusset plates at junctions and corners, all necessary fittings
complete including applying a priming coat of red oxide zinc chromate
primer

Providing and fixing water closet squatting pan (Indian type W.C. pan ),
100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing
cistern (same colour) conforming to IS : 7231, with flush bend and
other fittings and fixtures complete including cutting and making good
the walls and floors wherever required :

fittings and fixtures complete including cutting and making good the
walls and floors wherever required

Providing and fixing white vitreous china urinal basin with waste fitting
as per IS : 2556, and other couplings in C.P. brass complete:

Providing and fixing vitreous china wash basin with C.I. brackets, 32
mm C.P. brass waste of standard pattern, including painting of
brackets, cutting and making good the walls wherever required :

Cement concrete flooring with cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 20mm) finished with a floating
coat of neat cement.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply including all CPVC plain &
brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing.
This includes jointing of pipes & fittings with one step CPVC solvent
cement and testing of joints complete as per direction of Engineer in
Charge.

Providing and fixing 15 mm nominal bore Brass bib/stop cock of
approved quality:
19.13.1 Bib cock (250 grams)

Painting exterior surface with PREMIUM ACRYLIC SMOOTH exterior
paint of required shade as per manufacturer's specifications to give
protective and decorative finish including cleaning washing of surface etc.
complete with:

Constructing masonry Chamber 60x60x75 cm, inside with modular well
burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse
sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160
mm bottom diameter and 180 mm deep (inside) with chained lid and RCC
top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate

Excavation for all types and sizes of foundations, trenches and drains or
for any other purpose including disposal of excavated stuff upto 1.5 m lift
and lead upto 50m (at least 5m away from the excavated area), including
dressing and leveling of pits.

Providing and fixing aluminium composite panels in approved panel sizes,
thickness and shape on aluminium frame work on face of building. (Frame
to be paid separately)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand :
10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes
including bed concrete 150mm thick as per standard design:

Providing & laying 60mm thick precast interlocking concrete blocks of
approved size (approx 305 sqcm) and shape/ pattern, over 40 mm thick
average complete coarse sand bed with joints of 3mm thick filled by
fine sand including leveling with surface vibrator, temping and
sweeping etc. complete of minimum compressive strength of 250
kg/sq.cm

electi 10% lumsam

Sanitary Napkin vending machine

Sanitary Napkin disposable machine treatment incineration

white abs automatic hand dryer