Public Works Department Tender

Providing and Fixing if required High Back Chair for Executives: Dimensions: Width: 76.3cm, Depth 76.3cm, Height: 85.5-97.5cm Seat height: 42.5-54.5cm. Seat and Back are made up of 1.2+0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric Uplholstery covers and moulded Polyurethene foam. Griha /Green Gaurd Certified Chair for following govt. initiative of reducing carbon footprint. The back foam is designed with Contoured lumber support. High Resilience Polyurethene foam is moulded with density= 45+2kg/m3 and hardness load 16+2 kgf as per IS:7888 for 25% Compression. One piece armrests are injection moulded from black co-polymer polypropelene. The pneumatic Height adjustment has an adjustment stroke of 12.0+0.3cm. The bellow is 3 peice telescopic type and injection moulded in black polypropelene. injection moulded pedestal in black 33% glass filled nylon-66 and fitted with 5NOs.Mid Back Chair has twin wheel castors with 66.3+0.5cm pedestal pitch dia. a) High Back Chairs for Executives

Providing and Fixing if required Medium Back Chairs and Visitors for Executive Chambers: Dimensions: Width: 76.3cm, Depth 76.3cm, Height: 85.5-97.5cm Seat height: 42.5-54.5cm. Seat and Back are made up of 1.2+0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric Uplholstery covers and moulded Polyurethene foam. The back foam is designed with Contoured lumber support. High Resilience Polyurethene foam is moulded with density= 45+2kg/m3 and hardness load 16+2 kgf as per IS:7888 for 25% Compression. One piece armrests are injection moulded from black co-polymer polypropelene. must be Griha Certified Chair. The pneumatic Height adjustment has an adjustment stroke of 12.0+0.3cm. The bellow is 3 peice telescopic type and injection moulded in black polypropelene. injection moulded pedestal in black 33% glass filled nylon-66 and fitted with 5NOs. twin wheel castors with 66.3+0.5cm pedestal pitch dia. for Reducing the carbon foot print Greengaurd Certified chair. For Visitor: Tabular frame is made of Ø2.54+0.03cm x 0.2+0.16cm thick MSERW tube having cantilever type frame. a) Midium Back Chair

Providing and.Fixing if required lull HB Chair : Full BAck 'Size: 46.5 cm(W) x 60.0cm (H), Seat 51.0cm (W) x 49.0cm(D) Cushioned Scat Assembly consists of seat outer material 30% glass fiber nylone and upholstered Scat (Poly Propylene) with moulded polyurethane foam and Polyester fabric. t he net back is made up aback outer (material glass fiber filled' Nylon) & Back Inner (Material PP) and upholster using polyester mesh fabric With high tenacity yarn. High Resilience Polyurethane foam is moulded with density= 45+2kg/m3 and hardness load 12+2 kgf as per IS:7888 for 25% Compression. The support spine is made of High pressured Die cast polished aluminium. Armrest has two adjustments Height and Depth of 6.0+0.5cm. Height adjust meat is provided in aiuminurn structure of armrest which is connected Aluminium back spine and operated by button. Chair must be BIFMA level two, certified for design and Griha certified- for reducing the carbon footprint as per govt. green initiative. Armrest top is made. of PU molded over plastic inner. Adjustable tilting mechanism with following features. 360 revolving type. 5 position tilt limiter giving option of variable tilt angle. Seat back tilling ratio I :2. The mechanism housing is made up of HPDC Aluminium and black powder coated. Pneumatic height adjustment has an adjustment stroke of 10.0+0.3cm. a) Mesh Back High Back Chair

Providing and Fixing if required Visitor Chair: Scat Size: 65.5cm (W) x 58.2cm (D) 99.5cm (H) x seat Height 48.5cm Seat and back are made of 1.2+0.1cm thick hot pressed plywood. Measured as per QA method described in OCP-QLTA-PM-P14-18 and Upholstered with fabric and moulded polyurethene foam with PVC lipping all around. The one piece armrest is made of black integral skin polyurathene with 50-70 shore hardness and reinforced with M.S. insert. The tubular frame is cantiviler type & made up of 02.54+0.03cm x 0.2+0.016cm thick MSERW tube and black powder coated (DFT 40-60 microns.). Chair must be BIFMA level two certified for design and 1Griha certified for reducing the carbon footprint as per govt. green initiative. a) Mesh Back Visitor Chairs

Providing and Fixing it required Midium Mesh Back Chair: Full Back Size: 46.5cm(W) x 60.0cm (H) Seat 51.0cm (W) x 49.0cm(D) Cushioned Seat Assembly consists of seat outer material 30% glass fiber nylon and upholstered Seat (Poly Propylene) with moulded polyurethane foam and polyester fabric. The net back is made up of back outer (material Glass fiber filled Nylon) & Back Inner (Material PP) and upholster using polyester mesh fabric with high tenacity yarn. High Resilience Polyurethane foam is moulded with 45+2kg m3 and hardness load 12+2 kgf as per IS:7888 for 25% Compression. The support spine is made of High pres-sured Die cast polished aluminium. Armrest has two adjustments Height and Depth of 6.0+0.5cm. Height adjkust ment is provided in aluminum structure of armrest which is connected Aluminium hack spine and operated by button. Armrest top is made of PU molded over plastic inner. Chair must be BIFMA level two certified for design and Griha certified for reducing the carbon footprint as per 9,-ovt. green initiative. Adjustable tilting mechanism with following features. 360 revolving type. 5 position tilt limiter giving option of variable tilt angle. Seat back tilting ratio 1:2. The mechanism housing is made up of HPDC Aluminum and black powder coated. The pneumatic Height adjustment has an adjustment stroke of 10.0+0.3cm a) Mesh Back Mid Back Chair

Providing and Fixing if requiredTable for Executives: Size: Main Desk: (L)2100mm x (D)745mm x (H)765mm, ERU: (L)1600mm x (D)500mm x (H)650mm, Sliding Door for ERU (W)400mm x (H)520mm. Main Top: 1800X795MM ; Particle-board ( Melamine Finish), 25mm Top + 15mm frame; 2mm PVC Lipping on top and 0.35mm PVC Lipping on frame. MODESTY PANEL : 1100X405X 16mm THK Particle-board ( Melamine Finish) ; with 0.35mm THK PVC Lipping. DRAWER FRONT : 500X170X 16mm THK Particle-board ( Melamine Finish) ; with 0.35mm THK PVC Lipping. KBPT : 578 (W) X 284 (D) X 16mm THK Particle-board ( Melamine Finish) ; with 0.35mm THK PVC Lipping. ERU : 1600 (L) X500 (W) x 650 (H) all panels are 16mm THK Particle-board ( Melamine Finish) with 0.35mm THK PVC Lipping. A) Main Table + ERU

Providing and Fixing if required Premium Launge Chairs for Visitors and Waiting Halls: Premium lounge chairs of different seating capacity: Two seater: (W) 113.0cm x (D)70.0cm x (H) 78.5cm x Seat height 43.5cm. For Three Seater: (W) 164.0cm.X (D)70.0cm X (H) 78.5cm X Seat height 43.5cm. The premium lounge chair is flexing-back lounge seating system standing on beam with side frame assemblies. The side frame assembly is fitted to the two ends of the connecting beam assembly to form leg cum armrest assembly made of Ø3.81+0.03cm. X 0.2+0.016cm. thick MSERW tube and powder coated (40-60 microns). Ends are fitted with Caps. Material type is High resilience polyurethene foam having density 45+2kg/m3 with harness load 25+2 kgf. a) Premium lounge Chairs 2- Seater

Providing and Fixing if required Premium Launge Chairs for Visitors and Waiting Halls: Premium lounge chairs of different seating capacity: Two seater: (W) 113.0cm x (D)70.0cm x (H) 78.5cm x Seat height 43.5cm For Three Seater: (W) 164.0cm x (D) 70.0cm x (H) 78.5cm x Seat height 43.5cm. The premium lounge chair is flexing back lounge seating system standing on beam with side frame assemblies. The side frame assembly is fitted to the two ends of the connecting beam assembly to form leg cum armrest assembly made of 03.81+0.03cm. X 0.2+0.016cm. Thick MSERW tube and powder coated (40-60 microns). Ends are fitted with Caps. Material type is High resilience poiyurethene foam having density 45+2kg/m3 with harness load 25+2 kgf. b) Premium lounge Chairs 3 Seater

Providing and Fixing if required Main Desk + ERU + Back Unit + Pedestal for Senior Executives: Offered in a pleasant combination of white cedar & black Comprises of (a) Main Desk, (b) ERU, (c) Back storage Unit and (d) Mobile pedestal. • Main Desk is in size 1350w X 750d X 750h. The table top is in white cedar, side panels are in black, while the modesty panel is a combination of black & white cedar. The ERU is an independent standing unit. It is common for LHS & RHS. ERU is available in sizes: 1200mm Wx 450mm D x 750mm H. The ERU top is in white cedar, side panels are in black, whle the modesty panel is combination of black & white cedar. Black Storage unit is available in size 750W x 425D x 750H. It is a two door HDU with one adjustable shelf. The tp and shutters are in white cedar white cedar while the shelf, side panels and the back panel are in black. The suite can be sold with a single Back storage unit of as a set of 2unit placed besides each other. The two drawer (1 box drawer & Filing drawer) Mobiles Pedestal is available in one size: 390 x 435 x529 mm. The top & drawer fronts are in white cedar while the other components are in black Tops/Worksurfaces : (White Cedar) Made from 1Smm thick PLB with PVC lipping. Side Panels : (Black) Made form 1Smm thick PLT with PVC lipping /Modestv Panel : Made form 18mm thick PLT. with PVC lipping. Bigger upper panel in Black and smaller lower panel in white Cedar. Shelf Storage units and Open shelf ERU : (Black) Made form 18mm thick PLT with PVC lipping. Doors of Storage Units : (White Cedar) HDU with 2doors and adjustable shelf. Made from 18mm thick PLT with PVC lipping. Mobile Pedestal: One Box and one Filing drawer with 18mm thick PLB fronts and top. Handles : Black Powder coated Die cast Aluminum alloy handles: Mobile Pedestal and HDU are fitted with central Lock. a) Senior Executive Main Desk + ERU + Back Unit + Pedestal

Providing and Fixing if required Leathertte High Back and Visitor Chairs for Senior Executives: The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 ; upholstered with leatherite cover moulded High Resilience Polyurethane foam. The HR polyurethane foam is moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. The adjustable armrest is designed with the following features : · Up-Down adjustment– 8 steps (8.0±0.5cm range) · Height adjustable armrest structure which is chrome plated & fitted with an armrest top. · Fixed Armrest Top is PU moulded over metal insert. The adjustable tilting mechanism is designed with the following features. · 360° revolving type. Single point control. · Front-pivot for tilt with feet resting on ground,· Tilt tension adjustment. · 4-position locking with anti-shock feature. · Seat/back tilting ratio of 1:2. Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for High back and Mid back chair. The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 NOs. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) The twin wheel castors are injection moulded in black PP. The tubular frame is powder coated ( DFT 40-60 microns ) cantilever structure & made of Dia.Ø 2.54 ±0.03cm. x 0.2± 0.016cm.thk. M.S. E.R.W. Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the frame assembly. Seat can be slide horizontaly as per user convienience. Stroke of seat slide is 5 cm. This option is available for revolving pedstal type of chair. Visitor Chairs: The tubular frame is powder coated ( DFT 40-60 microns ) cantilever structure & made of Dia.Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the frame assembly. a) High Back Chair for Senior Executives

Providing and Fixing if required Leathertte High Back and Visitor Chairs for Senior Executives: The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 ; upholstered with leatherite cover moulded High Resilience Polyurethane foam. The HR polyurethane foam is moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. The adjustable armrest is designed with the following features : · Up-Down adjustment– 8 steps (8.0±0.5cm range) · Height adjustable armrest structure which is chrome plated & fitted with an armrest top. · Fixed Armrest Top is PU moulded over metal insert. The adjustable tilting mechanism is designed with the following features. · 360° revolving type. Single point control. · Front-pivot for tilt with feet resting on ground,· Tilt tension adjustment. · 4-position locking with anti-shock feature. · Seat/back tilting ratio of 1:2. Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for High back and Mid back chair. The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 NOs. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) The twin wheel castors are injection moulded in black PP. The tubular frame is powder coated ( DFT 40-60 microns ) cantilever structure & made of Dia.Ø 2.54 ±0.03cm. x 0.2± 0.016cm.thk. M.S. E.R.W. Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the frame assembly. Seat can be slide horizontaly as per user convienience. Stroke of seat slide is 5 cm. This option is available for revolving pedstal type of chair. Visitor Chairs: The tubular frame is powder coated ( DFT 40-60 microns ) cantilever structure & made of Dia.Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the frame assembly. b) Visitor Chairs

Providing and Fixing if required Leathertte Medium Back chair for Executives:The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 ; upholstered with synthetic leather over moulded High Resilience Polyurethane foam. The HR polyurethane foam is moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. The adjustable armrest is designed with the following features : · Up-Down adjustment– 8 steps (8.0±0.5cm range) · Height adjustable armrest structure which is chrome plated & fitted with an armrest top. · Fixed Armrest Top is PU moulded over metal insert. The adjustable tilting mechanism is designed with the following features. · 360° revolving type. Single point control. · Front-pivot for tilt with feet resting on ground,· Tilt tension adjustment. · 4-position locking with anti-shock feature. · Seat/back tilting ratio of 1:2. Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for High back and Mid back chair. The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 NOs. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) The twin wheel castors are injection moulded in black PP. The tubular frame is powder coated ( DFT 40-60 microns ) cantilever structure & made of Dia.Ø 2.54 ±0.03cm. x 0.2± 0.016cm.thk. M.S. E.R.W. Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the frame assembly. Seat can be slide horizontaly as per user convienience. Stroke of seat slide is 5 cm. This option is available for revolving pedstal type of chair. a) Mid Back Chair

Providing and Fixing if required Premium Desk + ERU + Back Unit: MAIN TOP: MDF + VENEER + PU Coating, Size : 3600 W * 1080 D * 750 H, TOP THICKNESS- 90 mm. MOBILE PEDESTAL: MDF + Veneer + PU Coating , Size :480 W X 640 D X600 H mm, ERU TOP: MDF + VENEER + PU Coating, Size :1900 W X 480D X 550 (NOt FromGround with Castors), TOP THICKNESS – 25 mm. Back Unit: MDF + VENEER + PU Coating & Glass Doors Size : 1000 W * 480 D * 2035H, GLASS THICKNESS – 5 mm. PU COATING HARDNESS - 1.5 H. Main Desk +ERU +Back Unit.

Providing and Fixing if required Premium Leather Upholstered Chairs: For VHB: (W) 75.0cm x 75.0cm(D) x (H)113.5-138.5 x seat height 41.0x 51.0cm. For HB: (W) 75.0cm x 75.0cm(D) x (H)101.0-118.0 x seat height 41.0x 51.0cm. For MB: (W) 75.0cm x 75.0cm(D) x (H)93.5-110.5 x seat height 41.0x 51.0cm Visitor: (W) 51.0cm x 66.5cm(D) x (H)96.0 x seat height 48.0cm. Seat : hot pressed moulded reconstituted wood of 1.2+.01cm thickness and back part in two part injection moulded plastic. Seat sub Assembly Size: 49.0cm(W) x 49.5cm (D) Back Sub Assembly Size(High BAck): 46.0cm (W)x 57.0cm(H). Back sub assembly size(Visitor with Wheels): 45.0(W) x 49.0cm(H) HEad Rest sub assembly size: 26.0(W) x 12.0(L) High Resilience Polyurethene foam is moulded with density= 45+2kg/m3 and hardness load 12+2 kgf as per IS:7888 for 25% Compression. Armrest: Pressured Die Casted in Polished Aluminium with PP Arm Tops. SynchriNOzed mechanism with 360 revolving type, seat back tilt ratio 1:3, side tilt adjustment NOb, back tilt with 4 position locking. Pneumatic height adjustment with adjustment strok of 10+0.3cm. Auto return mechanism for HB. Processed dia cast polished alumnium pedestal with 5 castors and 65+0.5cm pitch center Dia. For visitor understructure is welded structure made of MSERW Eliptical Tube. Powder coated 50+10 microns a) Main Chair VHB

Providing and Fixing if required Premium Leather Upholstered Chairs: For VHB: (W) 75.0cm x 75.0cm(D) x (H)113.5-138.5 x seat height 41.0x 51.0cm. For HB: (W) 75.0cm x 75.0cm(D) x (H)101.0-118.0 x seat height 41.0x 51.0cm. For MB: (W) 75.0cm x 75.0cm(D) x (H)93.5-110.5 x seat height 41.0x 51.0cm Visitor: (W) 51.0cm x 66.5cm(D) x (H)96.0 x seat height 48.0cm. Seat : hot pressed moulded reconstituted wood of 1.2+.01cm thickness and back part in two part injection moulded plastic. Seat sub Assembly Size: 49.0cm(W) x 49.5cm (D) Back Sub Assembly Size(High BAck): 46.0cm (W)x 57.0cm(H). Back sub assembly size(Visitor with Wheels): 45.0(W) x 49.0cm(H) HEad Rest sub assembly size: 26.0(W) x 12.0(L) High Resilience Polyurethene foam is moulded with density= 45+2kg/m3 and hardness load 12+2 kgf as per IS:7888 for 25% Compression. Armrest: Pressured Die Casted in Polished Aluminium with PP Arm Tops. SynchriNOzed mechanism with 360 revolving type, seat back tilt ratio 1:3, side tilt adjustment NOb, back tilt with 4 position locking. Pneumatic height adjustment with adjustment strok of 10+0.3cm. Auto return mechanism for HB. Processed dia cast polished alumnium pedestal with 5 castors and 65+0.5cm pitch center Dia. For visitor understructure is welded structure made of MSERW Eliptical Tube. Powder coated 50+10 microns a) Visitor Chair With Wheels

Providing and Fixing if required Premium Leather Upholstered Chairs: For VHB: (W) 75.0cmx 75.0cm(D) x (H)113.5-138.5 x seat height 41.0x 51.0cm. For HB: (W) 75.0cm x 75:0cm(D) x (H)101.0-118.0 x seat height 41.0x 51.0cm. For MB: (W) 75.Ocm x 75.0cm(D) x (H)93.5-110.5 x seát height 41.0x 51.0cm Visitor: (W) 51.0cm x 66.5cm(D) x (H)96.0 x seat height 48.0cm. Seat hot pressed moulded reconstituted wood of 1.2+.01 cm thickness and back part in two Ipart injection moulded plastic. Seat sub Assembly Size: 49.0cm(W) x 49.5cm (D) Back Sub Assembly Size(High BAck): 46.0cm (W)x 57.0cm (H). Back sub assembly size(Visitor with Wheels): 45.0(W) x 49.0cm(H) HEad Rest sub assembly size: 26.0(W) x 12.0(L) High Resilience Polyurethane foam is moulded with density= 45+2kg/m3. and hardness load 12+2 kgf as per IS:7888 for 25% Compression. Amrest: Pressured Die Casted in Polished Aluninium with PP| Arm Tops. SynchriNOzed mechanism with 360 revolving type, seat back tilt ratio 1:3, side tilt adjustment NOb, back tilt with 4 position locking. Pneumatic height| adjustment with adjustment strok of 10+0.3cm. Auto return mechanism for HB. Processed dia cast polished alumnium pedestal with 5 castors and 65+0.Scm piich center Dia. For visitor understructure is welded structure made of MSERW Eliptical Tube. Powder coated 50+10 microns b) Visitor Chair w/o Wheels

Providing, and fixing if required Premium Round Discussion table: worktop is made of 25mm THK PLT. KNOcked down understructure made from 8mm HR plate with Levellers & a vertical support tube of dia 90 & 2mm Thickness. A) Round Discussion Table 1050 diameter

Providing and Fixing if required Main Desk + Back Unit for Senior Executives: Main unit Desk: Overall Footprint: 1804 minx 750mm , Top thickness: 25mm, Top Dimensions: 1200mm x 750mm. Understructure Height: 725rnm, Overall Height: 750mm. Trident Senior. Back unit Desk: Overall Footprint: 1804 x 450Mm; Top thickness: 25mm, Top Dimensions: 1200 x 450mm. Understructure Height: 725mm, Overall Height: 750mm. Understructure; the understructure is in prelam panels, made with PLT boards. 2Drawer and 3Drawer storage units with different combinations to support Tops, made with 18mmPLT boards o different colors. Modesty and back panels, made with 18mm PLT boards. The Pedestals/Storages are fitted with necessary Locks. PLT Board Tops (Straight Edges): Tops for Juniorl Junior2 and Middle desk with ERU are of 18mm thickness. Made of 18mm thick PLT board with 2mm Edge banding. Wenge and Savannah Maple PLT board used for making Tops. PVC membrane Tops (with profiles): Tops for senior main and back unit desk are of PVC Imembrane pressed. Made of 25mm thick MDForie side laminate board with 0.4mm PVC membrane pressed on to tops. A top has Duck NOse and half round profiles edges. The top is made in only one finish: European Ash. a) Main Table with Back Unit

Providing and Fixing if required pure Leather Upholstered Premium Chair: SizeHB: (W)75.0cm x (D)75.0cm x (H)117.0-126.5cm. X Seat height 44.5-54.0cm. MB: (W)75.0cm x (D)75.0cm x (H)99.0-108.5cm. X Seat height 44.5-54.0cm. Visitor: (W)62.5cm x 56.5cm x (H)97.5cm x seath height 41.5cm The seat is made up of 1.2+0.1cm. Thick hot pressed plywood upholstered with pure leather, and polyurethane foam. the back of M.S. Fabricated frame upholstered with pure leather. Polyutathene cut foam is of density 32+2 kg/m3 and density for the back is 24+2kg/m3. The armrest top is soft touched upholstered with pure leather mounted on to an injection moulded height adjustable type armrest. It is adjustable in 5 steps. (including the lower most position.) The synchro mechanism is designed with the features such as: 360 revolving type, Single point control, Tilt tension adjustment and 5 position locking with anti shock featires. spine bracket is made of M.S. plate connecting the back with mechanism. The pneumatic height adjustment has an adjustment strock of 9.5+0.5cm. Pedestal high pressured Die Cast Aluminium fitted with 5 NOs. twin wheel nylon castors. For Visitor: Leg frame welded assembly is made of 3.8+0.8cm x 1.9+0.02cm x 0.12+0.0016cm elliptical MSERW tube with base for seat. a) Premium VHB Chair

Providing and Fixing if required pure Leather Upholstered Premium Chair: SizeHB: (W)75.0cm x (D)75.0cm x M)117.0-126.5cm. X Seat height 44.5. 54.0cm. MB: (W)75.0cm x (D)75.0cm x (H)99.0-108.5cm. X Seat height 44.5. 54.0cm. Visitor: (W)62.5cm x 56.5cm x (H)97.5cm x seath height 41.5cm The seat is made up of 1.2+0.1cm. Thick hot pressed plywood upholstered with pure leather, and polyurethane foam. the back of M.S. Fabricated frame upholstered with pure leather. Polyutathene cut foam is of density 32+2 kg/m3 and density for the back is 24+2kg/m3. The armrest top is soft touched upholstered with pure leather mounted on to an injection moulded height adjustable type armrest. It is adjustable in 5 steps. (including the lower most position.) The synchro mechanism is designed with the features such as: 360 revolving type, Single point control, Tilt tension adjustment and 5 position locking with anti shock featires. spine bracket is made of M.S. plate connecting the back with mechanism. The pneumatic height adjustment has an adjustment strock of 9.5+0.5cm. Pedestal high pressured Die Cast Aluminum fitted with 5 NOs. twin wheel nylon castors. For Visitor: Leg frame welded assembly is made 3.8+0.8cm x1.9 +0.02cm x0.12+0.0016cm elliptical MSERW tube with base for seat. a) Premium MB Chair

Providing and Fixing if required pure Leather Upholstered Premium Chair: SizeHB: (W)75.0cm x (D)75.0cm x M)117.0-126.5cm. X Seat height 44.5. 54.0cm. MB: (W)75.0cm x (D)75.0cm x (H)99.0-108.5cm. X Seat height 44.5. 54.0cm. Visitor: (W)62.5cm x 56.5cm x (H)97.5cm x seath height 41.5cm The seat is made up of 1.2+0.1cm. Thick hot pressed plywood upholstered with pure leather, and polyurethane foam. the back of M.S. Fabricated frame upholstered with pure leather. Polyutathene cut foam is of density 32+2 kg/m3 and density for the back is 24+2kg/m3. The armrest top is soft touched upholstered with pure leather mounted on to an injection moulded height adjustable type armrest. It is adjustable in 5 steps. (including the lower most position.) The synchro mechanism is designed with the features such as: 360 revolving type, Single point control, Tilt tension adjustment and 5 position locking with anti shock featires. spine bracket is made of M.S. plate connecting the back with mechanism. The pneumatic height adjustment has an adjustment strock of 9.5+0.5cm. Pedestal high pressured Die Cast Aluminum fitted with 5 NOs. twin wheel nylon castors. For Visitor: Leg frame welded assembly is made 3.8+0.8cm x1.9 +0.02cm x0.12+0.0016cm elliptical MSERW tube with base for seat. a) Premium Visitor Chair

Providing and Fixing if required Waiting Chairs 2 seater with extended sides for waiting Halls The seat is a welded assembly with the frame and the seat and back are made of 0.12 cm thk CR steel with oblong Perforation. They areweled ti side frame of size 3.2 cm X 0.5 cm thk HR Steel the welded assembly is powder Coated (DTF 40 60 microns). The seat front will have water fall edge for comfortable seating. It also have buttock support. curve for NOt only for rear support but also to prevent falling or the belongings from the gap between 'seat and back. Seat Size: 47.8 cm (W) X 44.6 cm (D) Back Size: 41.6 cm ( W) X 23 cm (H) •Understructure assembly consists of connecting beam and kg assembly made of MS ERW oblong tube of size 7.5 cm IX 5.0cm X 0:02 com Thk. The welded assembly is powder Coated (MT 40 - 60 microns). The leg assembly is fitted with shoes and levelers in nylon. The structure is designed with minimal are of contact close, to ground providing easy \access for cleaning purpose. a) Waiting Chairs 2 seater with extended sides

Providing and Fixing if required Waiting Chair: with Extended Sides for Waiting Hall The seat is a welded assembly with the frame and the seat and back are made of 0.12 cm thk CR steel sheet with oblong perforations. They are welded to side frame of size 3.2 cm X 0.5 cm thk HR Steel. The welded assembly is poweder Coated (DFT 40 60 microns). The seat front will have water fall edge for comfortable seating. it also have buttock support curve for NOt only for rear support but also to prevent falling of the belongings from the gap between seat and back. Seat Size: 47.8 cm (W) X 44.6 cm (D) Back Size: 41.6 cm (W) X 23 cm (H) Understructure assembly consists of connecting beam and leg assembly made of MS ERW oblong tube of size 7.5 cm X 5.0 cm X 0.02 com thk. The welded assembly is powder Coated (DFT 40- 60 microns). The leg assembly is fitted with shoes and levelers in nylon. The structure is designed with minimal are of contact close to ground providing easy access for cieaning purpose. a) Wating Chairs 3 seater with extanded sides

Providing and fixing if required glass top Corner table: (W)500mm X(L)500mm X(H)428mm X(T)8mm Glass of 8mm thk tempered, Solid rubber wood legs and frame MS sheet as bottom shelf. PU coating to the rubber wood parts clear glass. Black powder coating DFT=40-80 Microns. a) Corner Table

Providing and Fixing if required Computer Table for P.A. and SteNO: 3Desk with one drawer (RHS) & HDU attachment on one side & 3 drawer unit on the other side (LHS of user), Size 1500 x 750 x 750mm. Material: Top to be made of 18 mm thick high quality Pre-laminated boards with PVC edge banding. Locking: Locking facility available for top draswer/s only..Understructure to be made of 15 mm thick PLB with paper lamination. Locking facility to be provided in the top drawer only, with attractive silver cover handles for all drawers. It should have three drawer units oh LHS. a) Table for PA and SteNO

Providing and fixing morden day Workstations : WORKSURFACES: WORKTOP 25 MM THICK PRELAMINATED (with PVC edge band) Work top shall be made of 25mm thick prelaminated particle board interior grade (As per IS: 12823). Bottom shall have a backing- laminate of minimum. 0.6mm thickness. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC Edge band glued with hot melt EVA glue. 4.2 WORKTOP 25 MM THICK LAMINATED (with PVC edge band) Work top shall be made of 25mm thick Plain particle board of interior grade (As per IS: 12823) as a Substrate. The top shall be laminated with laminate of 0.6 mm thickness of approved shade as per IS: 2046-1995. Bottom shall have a backing laminate of 10.6 mm thickness. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC edge band glued with holmeit EVA glue. Underside of the work surface shall be screwed to cross connectors and ieg assembly. These workiops shail be provided with the sio: for access flap, as per requirement. METAL MODESTY PANEL: This shal! he made of O.8mm thick CRMS sheet Vertical stiffeners shall be spot- welded with. The metal modesty. Modesty assembly shall be coated with epoxy powder coating. PARTIAL WIDTH FRAMED SCREEN IN COMBINATION OF WHITE BOARD & FABRIC MAGNETICIS CONSIDERED ALONG WIDTH OF WORK SURFACE (a) Rectangular Work Station 2 Seater Side by Side

Providing and Fixing Pedestal for Work Stations to support the Worktop: TOP SUPPORTING PEDESTAL WITH FLAT METAL FRONT OF SIZE .390W X 585D X 720 HT, 3DR = 2 BOX + 1 FILE, CENTRAL LOCKING Welded Assembled. 0.8 thk CRCA for Body Shell. Drawer Front & trav. Front Side Stiffener. Rear Side Stiffener. 1.2 thk CRCA Top Stiffener & Bottom stiffener. Metal Front. Straight Edge. All Drawers with Double extension precision ball slide, 390 wide Pedestais File drawer, A4 files in width wise manner; For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. 10 lever Cam Lock & Central R locking with actuator & lock channel mechanism for BoxBoxFile Pedestals. Plastic M8 leveler mounted below Body Shell of 46mm height. Epoxy Polyester Powder coated to the (thickness of 50 microns (+/10). a) Top supporting Pedestal

Providing and fixing if required Keyboard Pull out Tray for Workstations: 'size 580 mm (W) x 280 mm (D) made ABS. It should also have in-built LHS/ RHS mouse pad, with 3 mm thick synthetic foam sheet with PVC on top.. The said tray shall be mounted on electroplated zinc (as per IS: 1573-1996) single Extension ball slides. a) KBPT

Providing and Fixing if required All Metal CPU Trolley: This is to be made from 14 BG MS CRCA sheet, powder coated 50-60 micron DFT. Width - 225 mm fixed, Height 330 mm fixed. Length Adjustable between 225 to 330 mm. A) CPU Trolly

Providing and Fixing if required the Computer table for junior Executives:The table is of size 5 ft (W) x 2 ft 6 inches (D) x 2 ft 6 inches ( H). The top of table is to be made of 18 mm thick pre-laminated plain particle board. All the edges of the top are duly sealed using 2 mm thick Doelleken beading, fixed by using Jowart/ Klibert glue. Understructure is made in form of 'C frame. Made of CRCA MS Sheet of 1.2 mm thk The tubular frame is to be made of MS ERW round tubes dia 25.4 mm x 1.2 mm thk. Drawer Unit (3 drawer): The shell of the drawer unit is to be made of 0.8 mm thick CRCA MS sheet. The drawer tray is made of 0.6 mm thick CRCA sheet and t he drawer front is made of 0.8 mm thick CRCA sheet. Drawer slides are based on friction slides of 1.2 mm thick CRCA sheet. It should have 6 lever brass lock. The handles of drawer are made of ABS plastic. a) Office Table (1650 X 900 X 728)

Providing and Fixing if required Revolving Chairs: Overall Size: (W)72.0cm x(D)72.0cm x(H) 95.3-104.3cm x (Seat height)43.7- 52.7cm. Seat and back are made of 1.2+0.1cm hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric on molded polyurethane foam. Seat upholstery is made of polyester fabric. The underneath of seat is covered with NOn-voven fabric. the back is a fabricated tubular frame assy, Powder coated (DFT 40-60 microns)& upholstered with high tenacity polyster mesh fabric. the MS tubular frame is made of Ø1.9+0.02cm x 0.2+0.016cm M.S. ERW tube. HR polyurethane foam, fixed type armrest injection moulded from black nylon. Chair has features such as: 360 revolving type, upright position locking, tilt tension adjustment and seat back tilting ratio 1:3.Pmeumetic height adjustment has an adjustment stroke of 9.0+0.3cm. Telescopic bellow assembly is a three piece telescopic type and injection moulded in balck polypropyiene. a) Revolving Chairs

Providin and Fixing if required Workstations as per gievn Specifications : The system is modular tile based open plan office system. Each panel comprises of a metal. Frame & tiles of various .finishes, snap-fitted to vertical sections of frames. .Metal fascia is fixed at bottom for wire management. Intermediate raceway is provided for additional wire management above-or below the work surface level. exposed vertical's .& horizontal are covered with flat metal trims. Overall thickness of the panel is 65mm. Listed below are the brief specifications of each sub-component of the product. The framework shall be welded rectangular frame made up of 2 vertical sections welded to horizontal tube at the top and C channel fat the bottom. Along with intermediate horizontal members which will fit into vertical members' slots, to accommodate cladding tiles of different heights, and Ito form a rigid structure. The finish will be powder coated in standard neutral colour. The vertical section shall be made- up of 1.5mm thick CRCA MS grade -D (as per IS: -513-1994) formed into C -channel- of 41.5 X 50MM. The uprights'shall have the rectangular slots, to carry wires, 1-NO. at the bottom & 2NOs. at the 'intermediate. Levels, of size .60mm (h) x•18mm (w). The pitch for mounting, the. I brackets shall be 25.4mm. Top' horizontalshall be 1.2 mm thk MS tube of 25.4 x 25:4 mm(1 x 1 inch). The bottom horizontal 'shall be 1.5mm thk C channel of MS ‘ CRCA. Grade D, size• 38. 1 mm. x 25.4mm ( 1 1/2 in'. x 1 in). The bottom I horizontal shall also have 2' slots for carrying wires; which will be of size 100mm (L) x 20mm (w). The panels shall have levelers made out of nylon "studs with screw insert with adjustment of +10mm. Exposed vertical and top edges of panels shall be covered with trims and top caps. Flat Trimsshall he of 69 mm W X 10.5 aim H and average wall thickness of 1.0 mm. These trims shall be made from Powder coated aluminum alloy (of grade He-9 — 63400) extrusions. the trims shall be fitted on the top horizontal using M6 X 35L Nut-bolts and the open vertical ends of the upright using M6 X 25L Bolt & Nut. The caps shall be made of ABS material, PU coated in colour desired or matching to trim colour. The frames shall be joined to each other to form different Layouts with the Joineries 2way 180°, 2way 90°. 3way 90, 4way 90°, 3way 120°, 2way 120, 3way 135' 2way 135'. The open vertical joineries for the configurations will be covered with aluminum alloy (of grade He-9 — 63400) vertical trims of 1.2 mm average wall thickness, which will be powder coated and press fitted onto the universal connector made of 2.0mm thick MS. using the 0.5nam thick spring steel snap fit clip. The universal connector shall be screwed to the frame using M6x 30 long socket button head screw. All MS components shall be pretreated and powder coated. Panel options: 'FABRIC MAGNETIC TILE/ NON-TACKABLE TILE : PLAIN METAL: TILE,LAMINATED TILE and WHITE BOARD. TILE: Metal fascia shall be powder coated, in 0.8 mm thick M.S./ CRCA Grade D as per IS: .513 -1994, which.will.be mounted. With a hook at bottom and Snap fit button on top (BLACK). These can be provided at the bottom level as weil as at/ the bell-line level above or 6" below the work surface. The fascia could be with or 'without cutouts for mounting of switches.:• The .witches should he mounted 50 mm from the edge - of the fascia . Work top - shall be made of 2.5mm thick prelaminated particle board interior grade (As per IS: 12823). Bottom shall have a backing laminate of minimum 0.6mm thickness. All the edges of work surface shall -be provided with machine pressed 2 mm thick PVC Edge band glued with hot melt EVA glue. a) Pentagolal Work Station I Module

b) Pentagolal Work Station Single Module

Providing and Fixing if required Morden Look Desk + ERU: OVERALL DIMENSION :2055X 1800mm Ht 750mm MAIN TOP 1800X900X 25MM THK ; Pre-Lam Particle Board ; with PVC edge binding MODESTY PANEL :1200X300X 15mm THK: Pre-Lam Particle Board, with PVC edge binding. DRAWER FRONT : 545X180mm 15mm THK; Pre-Lam Particle Board, with PVC edge binding. SLOT FOR ASCESS FLAP 4190X88mm, WIRE MANAGMENT: Pre-fitted sockets, UNDERSTRUCTURE SIDE FRAME : Rectangular MS Tube 98X12 mm; Finish :Powder coated. LOAD BEARING CAPACITY OF SHELF : 5kg uniformly distributed load EU has three drawers and one sliding door storage space. a) Morden Look Main Table + ERU

Providing and Fixing if required. Chairs: Overall Dimension: (W)66.0cm x (H)89-101cm x(D)66.0cm x (Seat height)40-52cm. The seat is made up of 1.2+.01cm thick hot pressed plywood and\ polyurethane foam Upholstered with polyester fabric and covered and bottom with NOn-woven black fabric.- The back is injection molded plastic and is upholstered with high tenacity mesh fabric. Seat Size: 48.0cm (W)x 48.0cm(D), Back Size: 44.5cm(W)x 43.0cm(H) Armrest is one piece loop type made up of black plastic injection moulded in nylon. Central tilt mechanism is designed with the following features - 360 revolving type with seat height adjustment kNOb. Upright position locking -tilt tension adjustment. pneumatic height adjustment is class-three category and has an adjustment of 12.0+0.5cm stroke. Pedestal Assy: the pedestal is made of moulded plastic _CTS; nylon and fined with 5 NOs. twin 'wheel castor. The - pedestal is of 56.0+0.5cm pitch center. diameter (66.0+1.0cm castors. ) a) NET Back Visitor Chair with Wheels

Providing and Fixing if required Verticle Sliding Door Units: It should have Rigid KNOck-down construction with press fit riveted design, made from 0.8 mm Prime Quality CRCA steel. Two sliding doors should be provided. It should have snap on type aesthetically appealing die cast 5 lever cam lock and plastic flush ecessed handles. Full height sliding doors with top hanging arrangement to prevent derailment and 2 plastic rollers having steel ball bearings. The shelves should be height wise adjustable, with UDL capacity of 80 Kgs. for full length and 40 Kgs. for half shelf. The top should be made of 25 mm thick PLB with 2 mm thick PVC edge banding. .All steel components should undergo eight tank anti rust treatment and oven baked epoxy polyester powder coated with 50 microns dry film thickness. The CRCA steel sheet used should be 0.6 mm thick as per IS-513 1994. It should have scratch hardness of 3 Kgs as BS-3900 part E2 1970, IS-101. It should sustain salt spray test of 1000 hrs. as IS 101. a) Verticle Sliding Door Unit (1192.5*1200*450)

Providing and Fixing if required Auditorium / Seminars 3 Seater front type Writting Desks for Auditorium: An Elegent Modular solution for different need of large Seminars or Auditorium Hails. Which can provide flexibility in layout! while doing-the seating arrangement without comprising the seating comfort.lages must be made of MS ERW tube Section aS7138) of size 72 X 25 X 2mm thick oval tube with 5mm thick HR brackets as per IS: 2062 and 2mm thick CRCA Brackets as per IS-513 welded on to the tubes. Assembly is powder coated with epoxy polyester. Leg height can variy from 705mm to 1000 mm in Ipitch of 50mm. Sturdy anchoring by anchoring bolts on to the base of 8mm thick 1 Plate for proper resting of Leg. Shoe made of ultramid nylon are provided at the bottom for covering the -base plate. Two side clads made of 18min thick plate with -0.8mm thick PVC lipping and on the outside covered with welded metal/ structure made ofg 2mm thick .CRCA as per IS-513 powder coated with Epoxy' polyester. Worktop are made of 25,mm thick PRe-Laminated Board of E1-P21 grade and approved shade confirming: to IS: 12823:1990. All the edges of work/ surface are provided with machine pressed2mm thick pvc edge hand glued with/ ;hot melt glue. Modesty is made of 25mm thick pre-laminated twin board of E 1-P2 grade and approved shade confirming -to IS: :12823:1990. All the edge of modesty are provided with machine pressed-2mm thick Pvc edge band glue with hot melt due. Dimensions Can be decided as per the Steps layout. a) 3 Seater Front Type worktop Desking for Auditorim

Providing and Fixing if required Canteen Tables for Canteen: Top Surface: 25mm Thick, Base material 25mm MDf board, PVC membrane foil on top. 8x2 deep groove on the center, of the table as graphics. Profiled edge. Brown laminated on the bottom. Understrucutre is bend pipe of MS. Powder coated. Pipe Dia 38mm, 2mm thick. Understructure fiited with top by SS machine screw. MS powder coated legs for PU. top & SS legs for membrane top. 38mm dia pipes legs are fixed with understructure and table top. Piastic glides |fixed at understructure to prevent the damage of table top during stacking. a) Canteen Table 4 Seater

Providing and fixing if required Canteen Tables: Work Surface25mm thick base material 25mm MDF board PVC membrane foil on top 8X2 deep Groove on the center of the table as graphics. Profiled edge, brown laminated on the bottom. Understrucutre is bend pipe of MS Powder coated. Pipe Dia 38mm, 2mm thick. Understructure fitted with top by SS machine screw. MS powder coated legs for PU top & SS legs for membrane top. 38mm dia pipes legs are fixed with understructure and table top. Plastic glides fixed at understructure to prevent the damage of table top during stacking. a) 6 Seater Canteen Table

Providing and Fixing if required Simple working Tables: Worktop: 25 mm Thick: PLB tops with 2.0mm Thick PVC Edge Beading. Understructure: C -Frames:.1 .6 mm thick M.S Cframe Supporting the Top. Legs Dia. 38.1- x 1.6 mm thick M.S ERW tube. Multipurpose Tables with PLB tops with rounded edges and Powder coated to 50 microns. a) Main Working Table 1800W