Public Works Department Tender

Providing and fixing M.S. frames of doors, windows, ventilators and
cupboards joints mitred and welded with 15x3 mm lugs 10cm long
embedded in cement concrete blocks 15x10x10cm of grade M-10 or with
wooden plugs and screws or with dash fastener or rawl plugs and screws
or with fixing clips or with bolts and nuts as required including fixing of
necessary butt hinges and screws and applying a priming coat of
approved steel primer. MS tubler frames

Providing and fixing steel door/ window with M.S. sheet 1mm thick, frame
of angle iron, diagonal braces of angle/ flat iron of suitable size, 3.00 mm
M.S. gusset plates at junctions and corners, all necessary fittings
complete including applying a priming coat of red oxide zinc chromate
primer.

Providing and constructing soak pit 1.20x1.20x1.20m filled with brickbats
including S.W. drain pipe 100 mm diameter and 1.20 m long complete as
per standard design.

Taking out door shutters (steel or wood) including stacking within 50 metres lead.

Taking out window shutters (steel or wood) including stacking within 50 metres lead.

Dismantling terrazzo or mosaic or glazed vitreous or patent cement or
tiled flooring or dado skirting of any thickness without sub base

Dismantling steel work in built-up section without dismembering for a span
upto 10 metre and height upto 5.0 metre above plinth level including
stacking with in 50 metre lead.

Repairs to plaster in patches of area 2.5 sq. metres and under including
cutting the patch in proper shape, raking out joints and preparing and
plastering the surface of the walls with cement mortar 1:4 (1 cement : 4
fine sand) complete including disposal of rubbish to the dumping ground
within 50metres lead :
17.1.1 Thickness upto 15mm

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved
make and conforming to IS:8931 including C.P. brass extension if
required:
19.14.1 Bib cock (400 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved
make and conforming to IS:8931 including C.P. brass extension if
required.
19.14.6 Stop cock (concealed) (600 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved
make and conforming to IS:8931 including C.P. brass extension if
required.
19.14.12 Bottle trap set with extension pipes

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved
make and conforming to IS:8931 including C.P. brass extension if
required.
19.14.18Wall mixer (telephonic type) with crutch arrangement for hand shower
(1400gms)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing water closet squatting pan (Indian type W.C. pan ),
100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing
cistern (same colour) conforming to IS : 7231, with flush bend and
other fittings and fixtures complete including cutting and making good
the walls and floors wherever required
18.1.3 White Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing vitreous china water closet (European type W.C.
pan) with white ISI marked plastic seat and lid, 10 litre low level white
P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all
fittings and fixtures complete including cutting and making good the
walls and floors wherever required :
18.4.1 White pedestal type

Providing and laying nominal mix plain cement concrete with crushed
stone aggregate using concrete mixer in all works upto plinth level
excluding cost of form work3.1.3 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm
nominal size).

Providing and laying vitrified floor tiles with double charge/ multi charge
printing with water absorption less than 0.5% and conforming to IS :
15622 of approved make in all colours and shades and size mentioned
below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4
coarse sand) including grouting the joints with white cement and
matching pigments etc. complete.
12.13.1 Size 600x600mm

Providing and laying ceramic glazed floor tiles conforming to IS : 15622of approved size, make, colour, shade laid on 20 mm thick CementMortar 1:4 (1 cement : 4 coarse sand) including pointing the joints withwhite cement mixed with matching pigment etc., complete.
12.9.2 Size above 300x300mm

Providing and fixing ceramic glazed wall tiles conforming to IS : 15622
of approved make, colours, shades and size on wall and dados over 12
mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and
jointing with grey cement slurry @ 3.3kg per sqm including pointing in
white cement mixed with matching pigment complete.
12.7.1 Size upto 200x300mm

Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to
IS:12894-2002 of class designation 4.0 in foundation and plinth in:Cement Mortar 1:5 (1 cement : 5 coarse sand)

16.53 Removing following vitreous china sanitorywares carefully for re-use
including stacking within 50 metres lead.
16.53.1 Wash basin of all sizes and shapes

16.53 Removing following vitreous china sanitorywares carefully for re-use
including stacking within 50 metres lead.16.53.3 European/ Anglo Indian WC pan of all sizes

16.53.5 PVC Cistern

Providing and replacing broken/ damaged false ceiling tiles with new
ceiling tiles on existing frame work.
17.25.1 12mm thick unveneered Nova teak or equivalent super plain tiles

Supply and fixing of precoated galvanized iron profile sheets (size, shape
and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm +/-
5% total coated thickness (TCT), Zinc coating 120gsm as per IS: 277 in
240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet
and polyester top coat 15-18 microns. Sheet should have protective guard
film of 25 microns minimum to avoid scratches while transportation and
should be supplied in single length upto 12 metre or as desired by
Engineer-in-charge. The sheet shall be fixed using self drilling /self
tapping screws of size (5.5x 55mm) with EPDM seal or with polymer
coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I.
limpet washers or with G.I. limpet washers filled with white lead complete
upto any pitch in horizontal/ vertical or curved surfaces excluding the cost
of purlins, rafters and trusses and including cutting to size and shape
wherever required.

Cement concrete flooring with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm) finished with a floating coat of neat cement.
12.3.1 40 mm thick

14.14 Finishing walls with water proofing cement paint of required shade to give
an even shade.
14.14.1 On new work (Two or more coats applied @ 3.84 kg/10 sqm)

19.14 Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required:
19.14.20 CP brass water jet to be fixed in seat cover of WC with flexible connection pipe

Providing and fixing stainless steel drain jali of approved make/quality

10.64 Providing and fixing of aluminium panel false ceiling of approved colour consisting of panels 300mm wide x 30 mm deep x 0.7mm thick with bevel edge and length up to 6.0 metre. The panels are made from corrosion resistance aluminium alloy AA 3005 (Al. Mg) (for higher strength and good roll forming characteristics) sheet chromatised for maximum bond between metal and paint, enamel painted twice under high temperature, one side with a full primer and finish coat and the other side (inner side) with a primer coating and Skin Coat on a Continuous Paint Line.
Panel shall be fixed by clipping to panel carrier of size 41.5mm wide x 62mm deep x 0.95mm thick in standard length of upto 5 metre made of doubled baked black enamelled aluminium alloy AA 5050 (Al. Mg) with cut outs to hold the 300mm wide panels fixed at a distance of 0.3 m from wall and 2.4 m from centre to center. Panel carrier shall be suspended by means of G.I. suspension rod 4mm dia and a Galvanised suspension spring clip at a distance of 1.7 m centre to center.
Wall trim box of size 15x30x15mm made from 0.4mm thick aluminium alloy sheet to be provided all along the wall to hold panels
(only surface area of false ceiling is to be measured and no deductions for lights, diffusers, columns etc shall be made)
10.64.1 With long Plain panels

9.61 Providing and fixing aluminium composite panels in approved panel sizes, thickness and shape on aluminium frame work on face of building. (Frame to be paid separately)
9.61.2 4mm thick

Designing, providing and fixing aluminium frame work made of special aluminium section on building face with M.S. angle iron brackets fixed on RCC structure with S.S. hold fasteners, including providing and fixing two sided structural adhesive tape of appropriate grade (NORTON or equivalent), on aluminium sections for fixing aluminium/ glass panel,
sealing on periphery of frame work, by providing EPDM gasket, silicon weather sealant between aluminium frame and building structure including hire charges of double scaffolding complete.