Public Works Department Tender

Demolishing cement concrete including disposal of material within 50 metre lead 1:3:6 or richer mix .

Dismantling terrazzo or mosaic or glazed vitreous or patent cement or tiled flooring or dado skirting of any thickness without sub base

Taking out door shutters (steel or wood) including stacking within 50 metres lead.

Dismantling doors chowkhats with shutters (steel or wood) including
architrave, hold fast etc. complete and stacking within 50 metres lead.

Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in Cement Mortar 1:5 (1 cement : 5 coarse sand):

Repairs to plaster in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls with cement mortar 1:4 (1 cement : 4
fine sand) complete including disposal of rubbish to the dumping ground within 50metres lead : Thickness more than 15mm and upto 20mm

Providing and fixing in position wall panelling at all heights with integral sensified calcium silicate panels/tiles of size 595x595 mm having NRC (Noice reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum) Non combustible as per BS;476 (part-4), fire performance as perBS;476 (part-6 &7) humidity resistance of 100% thermal conductivity 0.048 to 0.050 W/m0 KC as per ASTM 518:1991 , weight 1.900 Kg to 2.100 Kg per tile, 15 mm edge Density Having450 Kg/cum & 10 MM Central portion of tile having 350 Kg/cum, compressing of a frame made from eapeciallufabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e. vertical studs of size 48x34x36mm are placed at 600mm center to center in a floor and ceiling channel section of size 50x32 m fixed to the floor and soffit at 600 mm centers using 12mm dia, 40mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots ans finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fibre joint tape roll 50 mm wide (90 meter) roll and two coats of primer suitable for panelling as per manufacture's specification as per direction of Engineer-in-Charge all complete.

Providing and fixing false ceiling at all heights with 15 mm thick intergral densified tegular edged light weight calcium silicate false ceiling tile reinforced with fibre and natural filler false ceiling tiles of Size 595x595 MM of approved texture, design and patterns (such as cosmos, spinton,quata,glob) having NRC (Noice reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% fire performance as per BS:476 (part 6&7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050, W/m0KC as per ASTM 518:1991,Weight 1.900 Kg to 2.100 Kg per tile , 15 MM central Portion of tile having 350 kg/cum. in true horizontal lecel suspended on interlocking metel T-Grid of got sipped galvanised iron section of 0.33mm thick (galvanized @120 grams per sqm including both sides) comprising of main T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm ans secondary intermediate ceoss - T of size 24x32 mm of length 600 mm to form geid module of size 600x600 mm, suspended from ceiling using glavanised mild steel items (galvanizing @ 80 geams per sqm) i.e. 40 mm ling, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fullu threaded hanger rod upto 1000 mm length & L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000 mm to be fixed om periphery wall / partition with the help o fplastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.Sscrews, The work shall br carried out as per specifications, drawing ans as per directions of the Engineer-in-chage. Ceiling height up 3.5 mt. from adjacent floor level. extra height to be paid separately.

Providing and fixing at all height false ceiling consisting of frame work

Extra for sunk or raised mouldings in the Gypsum board/ plaster of paris false ceiling.

Providing and fixing wall paneling frame made of commercial grade 12mm
thick water proof ply strips 100mm wide at 600mm apart center to center
vertically and horizontally with necessary screws, wooden plugs etc
complete as required.

Providing and fixing commercial grade water proof ply for wall paneling on
wooden frame with necessary nails complete as required. 19mm

Providing and fixing approved shade veneering on wood wall paneling complete as required.

Providing and fixing teak wood moulded beading to doors windows frames including necessary screws and primary coat on exposed surface. 50x19mm

Providing and fixing 200 mm wide teak wood moulding such as base moulding, chair rail, architrave, moulded posts moulding skirting including necessary screws and painting on unexposed surfaces with wood primer
etc complete for per cm thick.

Providing and laying PU polish on new wood work (two or more coats)
with spray machine after preparing surface by rubbing down smooth with
sand papers, preparation of surface, applying 5 to 10 coats of French sprit
polish, applying two coats of PU sealer and finally applying two coats of
PU clear as per manufacturers specifications complete:

Applying one coat of cement primer on wall surface (applied @ 0.80
litrs/10 sqm) complete.

Providing and applying 2mm thick ready mix exterior grade approved
make putty (like Birla wall care, Alltek Superfine W/R of (NCL), Asian, ICI,
Nerolac, J.K. wall putty) on walls to make the surface smooth and even.

Wall painting with acrylic luxury emulsion (plastic) paint of required shade to give an even shade. On new work (two or more coats)

S/s curtain rod with s/s finial & clamp of 25mm dia made of jindal steel with heavy quality steel & all its material including all its finish.

Plain curtain cloth of perfect in width the curtain is best in finishing and meet exact reuirement of patrons of ddecor or equivalent. The curtain having quality checked with stretch resistance & perfect finished. Width of ''54''

Stitching of curtain with eyelets i/c all its materials such as aluminium rings with polypropylene ring of 32mm dia fixed on machine cut imported tap also included all stitching and fitting charges stitching and fitting charges.

Aster cloth blackout quality uv rays protector with 100% blackout quality with blockage of light.

Providing and Fixing if required High Back Chair for Executives: Dimensions: Width: 76.3cm, Depth 76.3cm, Height: 85.5-97.5cm Seat height: 42.5-54.5cm. Seat and Back are made up of 1.2+0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric Uplholstery covers and mouided Polyurethene foam. Griha/Green Gaurd Certified Chair for following govt. initiative of reducing carbon footprint. The back foam is designed with Contoured lumber support. High Resilience Polyurethene foam is moulded with density 45+2kg/m3 and hardness load 16+2 kgf as per IS:7888 for 25% Compression. One piece armrests are injection moulded from black co-polymer polypropelene. The pneumatic Height adjustment has an adjustment stroke of 12.0+0.3cm. The bellow is 3 peice telescopic type and injection moulded in black polypropelene. injection moulded pedestal in black 33% glass filled nylon-66 and fitted with 5nos.Mid Back Chair has twin wheel castors with 66.3+0.5cm pedestal pitch dia.

a) High Back Chairs for Executives

Providing and Fixing if required Full HB Chair:
Full Back Size: 46.5cm(W) x 60.0cm (H), Seat 51.0cm (W) x 49.0cm(D) Cushioned Seat Assembly consists of seat outer material 30% glass fiber nylone and upholstered Seat (Poly Propylene) with moulded polyurethene foam and polyster fabric. The net back is made up of back outer (material glass fiber filled Nylon) & Back Inner (Material PP) and upholster using polyster mesh fabric with high tenacity yarn. High Resilience Polyurethene foam is moulded with density 45+2kg/m3 and hardness load 12+2 kgf as per IS:7888 for 25% Compression. The support spine is made of High pressured Die cast polished aluminium. Armrest has two adjustment Height and Depth of 6.0+0.5cm. Height adjkust ment is provided in aluminium structure of armrest which is connected Aluminium back spine and operated by button. Chair must be BIFMA level two certified for design and Griha certified for reducing the carbon footprint as per govt. green initiative. Armrest top is made of PU molded over plastic inner. Adjustable tilting mechanism with following features. 360 revolving type. 5 position tilt limiter giving option of variable tilt angle. seat back tilting ratio 1:2. The mechanism housing is made up of HPDC Aluminium and black powder coated. The pneumatic Height adjustment has an adjustment stroke of [10.0+0.3cm.

a) Mesh Back High Back Chair

Providing and Fixing Brass Antique finished Door Handle 24

Providing and Fising Brass Antique finished Tower Bolt 12

Providing and Fixing Brass Antique finished Hinges 6

Providing and Fixing Hettich Door Closer with EN1154 Certified Fire Rated 5,00,000 cycle tested with all accessories complete fitting as per the direction of Engineer-In- each Charge.

Providing and Fixing Mortise lock with Locking arrangement with heavy handle
complete make Hettich lock with all accessories complete fitting as per the direction of Engineer-In-Charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position. Teak wood

Providing 40x5mm iron hold fast 40cm long including fixing to frame with 10mm bolts nuts and wooden plug and embedding in Cement Concrete 1:2:4 in blocks of size 30x10x15cm.

Providing and fixing flush door shutters, conforming to IS : 2202 (Part-I), decorative type core of block board construction with frame of first class hard wood and well matched teak ply veneering with vertical grains or cross bands and face veneers on both faces of shutters excluding hinges. 35 mm. thick (single leaf)

Providing and fixing bright finished brass butt hinges with brass polished MS screws complete: 125x85x5.50 mm (Heavy Type)

Providing and fixing bright finished brass tower bolts (barrel type) with brass polished MS screws complete: 250x10mm

Providing and fixing bright finished brass door handles with brass polished MS screws complete: 125MM

Providing and fixing 150mm bright finished brass floor door stopper with
rubber cushion & brass polished MS screws etc complete to suit the
shutter thickness.

Providing and fixing bright finished brass sliding door bolt with nuts and brass polished MS screws complete: 300x16mm

Providing and fixing brass door latch with brass polished MS screws complete: 300x16x5 mm

Providing and fixing brass door latch with brass polished MS screws complete: 250x16x5 mm

Providing and fixing of Convention hall table made of size width 650mm and meter height 80mm and height 80mm made with 18mm thick BWP as per I.S. 710 2010 marin grade ply (Green ply) table top front and side with 4mm thick premimum grade veneer of green or century and formica conforming to IS 2046: 1996 and I.S. 3513: 1966 laminate on all sides top & bottom all hiddne portion with necessary adhesive, teak wood beading (as per drawing). Table to have cable management: cable spines below the table top for vertical travel of cable or through legs as per details in such manner that no wire shall be visible individual race waly arrangement through power beam under table for data and power cable. Dimensions of the table should i.e. according to drawings and to the satisfaction of Engineer in charge.

Providing and Fixing if required Computer table: all wood desk. The desk Nos comprises of a Worktop, Side panels and Modesty panel and a freestanding pedestal. The entire desk mit is assembled with suitable KD fittings and hardware. Each side panel is provided with a cutout for laying cables for the monitor and other computer accessories. Worktop: Made from 25 mm Thick Pre laminated Particle board. All theedges are sealed with 2 mm thick PVC edge band all around. Side Panels: Made from 25 mm Thick Pre-laminated Particle board. All the edges are sealed with 2 mm thick PVC Edge band on the user side and 0.8 min on the Top and Bottom Side. The side panels have 2 glide screws each for leveling of the desk. Modesty Panel; Made from 18 mm Thick Pre- laminated Particle board. All the edges are sealed with 0.8 min thick PVC edge band all around. Freestanding Pedestal: The freestanding pedestal is made from 18 mm Pre-laminated Particle board with a combination of 2min and 0.8 mm. PVC Edge band on all the exposed surfaces as per requirement. The drawers are provided with suitable slides for smooth operation. All the pedestal drawers are centrally locked with a single key.

a) Computer Table (1200 x 600 x 740)

Providing and laying DOUBLE/ MULTI CHARGE (minimum 2.0 mm thick layer) VITRIFIED floor tiles with water absorption less than 0.05% and conforming to IS :15622-2017of 1st quality of approved make in all colours and size mentioned below(+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.

Extra for fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477 (Type 2) for interior/exterior applications, using 5kg. adhesive per sqm of tile area, in 3mm-6mm thickness in place of cement mortar.

Providing and fixing Plywood board partition including Door consisting of frame of first class hard wood and well matched teak ply veneering on both faces of partition, Melamine polish on wood work (two or more coats) with spray machine after preparing surface by rubbing down smooth with sand papers, preparation of surface including hinges, Glass etc.complete

Providing and Fixing if required Main Desk + Back Unit for Senior Executives: Main unit
Desk: Overall Footprint: 1804 mmx 750mm , Top thickness: 25mm, Top Dimensions:
1200mm x 750mm. Understructure Height: 725mm, Overall Height: 750mm. Trident Senior
Back unit Desk: Overall Footprint: 1804 x 450mm , Top thickness: 25mm, Top Dimensions:
1200 x 450mm. Understructure Height: 725mm, Overall Height: 750mm. Understructure:
The understructure is in prelam panels, made with PLT boards. 2Drawer and 3Drawer storage
units with different combinations to support Tops, made with 18mmPLT boards of different
colours.  Modesty and back panels, made with 18mm PLT boards.  The
Pedestals/Storages are fitted with necessary Locks. PLT Board Tops (Straight Edges): Tops
for Junior1, Junior2, and Middle desk with ERU are of 18mm thickness. Made of 18mm
thick PLT board with 2mm Edge banding. Wenge and Savannah Maple PLT board used for
making Tops. PVC membrane Tops (with profiles): Tops for senior main and back unit desk
are of PVC membrane pressed. Made of 25mm thick MDFone side laminate board with
0.4mm PVC membrane pressed on to tops.
The tophas Duck nose and half round profiles edges. The top is made in only one finish:
European Ash. A) Main table with back unit.

Providing and Fixing if required Visitor Chair: Scat Size: 65.5cm (W) x 58.2cm (D) 99.5cm
(H) x seat Height 48.5cm Seat and back are made of 1.2+0.1cm thick hot pressed plywood.
Measured as per QA method described in OCP-QLTA-PM-P14-18 and Upholstered with
fabric and moulded polyurethene foam with PVC lipping all around. The one piece armrest is
made of black integral skin polyurathene with 50-70 shore hardness and reinforced with M.S.
insert. The tubular frame is cantiviler type & made up of 02.54+0.03cm x 0.2+0.016cm thick
MSERW tube and black powder coated (DFT 40-60 microns.). Chair must be BIFMA level
two certified for design and 1Griha certified for reducing the carbon footprint as per govt.
green initiative. a) Mesh Back Visitor Chairs

Wooden Storage cabin made in teak wood teak veneer and MDF boardwith three nos telescopic channels fitted drawers and two cupboard with all brass fittings and top covered with 8 mm brown tempered glass of branded quality cabinet made by skilled laboirs with wood section of 1

wooden storage cabinet made in teak wood, teak veneer and MDF board with three nos telescopic channels fitted drawers and two cupboard with all brass fittings and top covered with 8 mm brown tempered glass of branded quality cabinet made by skilled labours with wood section of 1

Providing and Fixing if required Premium Synthetic Leatherette Sofa:
The under-structure should be made from tropical seasoned hard wood / particle board. The
webbing material should be nylon strips of width 2” / 3”. The foam at the back of the sofa
should be Polyurethane slab stock foam with 1” recron layer filling at back and arms. Foam
density to be 28 Kg / Cu. Mtr. The foam of the seat should be Polyurethane slab stock foam
with 1” recron layer filling. Foam density to be 28 Kg / Cu. Mtr. The sofa should be
upholstered with PU synthetic leather. The legs to be visible in front, made of MDF wooden
fascia with melamine coating.
Three Seater Overall size: 200.0 cm (W) x 88.0 cm (D) x 78.0 cm (H) x 45 Cms. (SH) (
Premium Sofa 3 Seater)

Providing and Fixing if required Premium Synthetic Leatherette Sofa:
The under-structure should be made from tropical seasoned hard wood / particle board. The
webbing material should be nylon strips of width 2” / 3”. The foam at the back of the sofa
should be Polyurethane slab stock foam with 1” recron layer filling at back and arms. Foam
density to be 28 Kg / Cu. Mtr. The foam of the seat should be Polyurethane slab stock foam
with 1” recron layer filling. Foam density to be 28 Kg / Cu. Mtr. The sofa should be
upholstered with PU synthetic leather. The legs to be visible in front, made of MDF wooden
fascia with melamine coating.
Three Seater Overall size: 200.0 cm (W) x 88.0 cm (D) x 78.0 cm (H) x 45 Cms. (SH)
(Premium Sofa 2 seater)

Center table wooden made in CP teak wood with best quality teak as per choice with
matching carving work as sofa set with 12mm thick branded (Modiguard make) float glass
top of best quality- polished on all edges, wood sections of 4*2inches, 4*4inches,3*2 inches,
1*1 inches and 2*2inches to provide best strength and design, polished completely in Hi-gloss
melamine matt polish of best quality done by skilled labors for long last & scratch resistant
polish. Size:- 54*30*18inches.

Side table wooden made in CP teak wood of best quality as per choice with matching carving
work as sofa set with 12mm thick top branded (Modiguard make) float glass of best quality
polished on all edges, wood sections of 4*2inches, 4*4inches and 2*2inches to provide best
strength and design , polished completely in Hi-gloss melamine polish of best quality done by
skilled labors. for long last & scratch resistant Polish. Size:-21*21*18inches

Providing and Fixing if required pure Leather Upholstered Premium Chair:SizeHB:
(W)75.0cm x (D)75.0cm x (H)117.0-126.5cm. X Seat height 44.5-54.0cm. MB: (W)75.0cm
x (D)75.0cm x (H)99.0-108.5cm. X Seat height 44.5-54.0cm. Visitor: (W)62.5cm x 56.5cm x
(H)97.5cm x seath height 41.5cm The seat is made up of 1.2+0.1cm. Thick hot pressed
plywood upholstered with pure leather, and polyurethane foam, the back of M.S. Fabricated
frame upholstered with pure leather. Polyutathene cut foam is of density 32+2 kg/m3 and
density for the back is 24+2kg/m3. The armrest top is soft touched upholstered with pure
leather mounted on to an injection moulded height adjustable type armrest. It is adjustable in
5 steps. (including the lower most position) The synchro mechanism is designed with the
features such as : 360 revolving type, Single point control, Tilt tension adjustment and 5
position locking with anti shock featires. spine bracket is made of M.S. plate connecting the
back with mechanism. The pneumatic height adjustment has an adjustmentstrock of 9.5+0.5
cm. Pedestal high pressured Die Cast Aluminium Fitted with 5 nos. twin wheel nylon castors.
For Visitor: Leg Frame welded assembly is made of 3.8+0.8cm. x 1.9+0.2cm. x

Providing and Fixing if required Vertical Sliding Door Units:
It should have Rigid Knock-down construction with press fit riveted design, made from 0.8
mm Prime Quality CRCA steel. Two sliding doors should be provided. It should have snap
on type aesthetically appealing die cast 5 lever cam lock and plastic flush ecessed handles.
Full height sliding doors with top hanging arrangement to prevent derailment and 2 plastic
rollers having steel ball bearings. The shelves should be height wise adjustable, with UDL
capacity of 80 Kgs. for full length and 40 Kgs. for half shelf. The top should be made of 25
mm thick PLB with 2 mm thick PVC edge banding. .All steel components should undergo
eight tank anti rust treatment and oven baked epoxy polyester powder coated with 50 microns
dry film thickness. The CRCA steel sheet used should be 0.6 mm thick as per IS-513
1994. It should have scratch hardness of 3 Kgs as BS-3900 part E2 1970, IS-101. It should
sustain salt spray test of 1000 hrs. as IS 101.
Vertical Sliding Door Unit
(1192.5*1200*450)

Providing and fixing approved make & color Floor carpet on 3mm foam base (local) using
company based adhesive. The carpet is nylon based with looped pile construction type. The
pile composition of the carpet is 100% polymer with tuft gauge of 1/10. The pile height of the
carpet is 10mm and pile weight of 1.65kg/m2 (+/-15%). The Total height of carpet is 15mm
with 3mm foam base. as specification

Providing and fixing Soap dish Holder of Jaquar makemodel No. AKP- 35731P including all necessary screws fittings ect complete.
Soap dish Holder

Providing and fixing Toilet Roll Holder with Stainless Steel flap of Jaquar make model No. ACN-CHR-1153S including all necessary screws fittings ect complete.
Toilet Roll Holder

Providing and fixing S.S. Towel Rack 600 mm long with lower Hangers,of Jaquar make model No. AKP-35781 PS including all necessary screws fittings ect complete.
S.S. Towel Rack 600 mm long with lower Hangers

Providing and fixing 15mm nominal bore single lever basin mixer with popup waste AND 450mm long braided hoses of Jaquar make model no. LYR-38001B including all necessary connections.
Single lever basin mixer with popup waste

Providing and fixing white vitreous Counter Top china wash basin with Fixing Acessories of Jaquar make model no. FLS-WHT-5931 including making all connections but excluding the cost of fittings :
Counter Top Vitreous china wash basin 515X365X120 mm

Providing and fixing Two Way Bib Cock with Wall Flange of Jaquar make model no. LYR-38041 including all necessary connections.
Two Way Bib Cock with Wall Flange

Providing and fixing angular stop cock with wall flange of jaquar make model no LYR-38053 including all necessary connection.
Angular stop cock with wall flange

Engineered Wooden floor 9mm thickness made of engineered wood win upper layer or random size with 2mm thickness of veneer high quality pu polish win underlay & fitting & installation inches.

Office table Executive office table alder make or equivalent, make complete in MDF board in 18mm and 12mm thickness board (ISI graded ) as per IS 710: 2010 melamine polish on all sides best quality fitting and telescopic channels fitted drawers with knob /handle and locks at branded company polished on all surfaces in dark walnut polish in matt finish with separate computer trolly fitted with wheels and drawer rack fitted with telescopic channel and lock size (72x30x30 inches) 1800x750x750 mm

Revolving chair with heavy with high back and neck rest cusioned seat and back and handle arms all adjustable with hydrolic fitting for height adjustment and back tilt and heavy 5 wheel base on bottom of royal koos make or equiralent.

visitor chair is 5 types metal chromed hollow pipe frame with arms, with cushioned seat and back coverd with high quality leather in back cover, heavy structue of elder make or equivalent, size 450x500 mm

Duplex blind with born sheer & opaque function double coated fabric blinds with all its track & cower with curtain ball mechanism with weight drop at bottom of 'd' décor brand.