Ministry Of Road Transport And Highways Tender

8.04 Retro- reflectorised Traffic signs (Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of retro-reflective type sheeting and vide clause 801.3, 2mm thick aluminium sheeting, 3mm/4mm thick Aluminum composite material sheet depending on the size of the sign fixed over back support frame of min 40 x 40 x 5mm Angle mounted on a mild steel circular pipe 65 NB ,3.2 mm thicknness firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing and painting all components of the signs and supports as per clause 7.2 of IRC:67 ) A) Made of Class-C Micro Prismatic Grade Sheeting of Type-XI (for National Highways and State Highways) a) With Aluminum Sheeting of 2 mm thickness (ii) 90 cm equilateral triangle

a) With Aluminum Sheeting of 2 mm thickness (xv) 90 cm High Octagonal

(a) Stop Sign Board (vi) 90 cm circular

8.05 Direction and Place Identification signs upto 0.9 sqm size board. (Providing and erecting direction and place identification retro-reflectorised sign as per IRC :67 made of retro reflective type sheeting and vide clause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminum composite material sheet with overall thickness of 4mm with area not exceeding 0.9 sqm and fixed over back support frame of min 35 x 35 x 3mm Angle mounted on a mild steel circular pipe 65 NB, firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing) A) Made of Class-C Micro Prismatic Grade Sheeting of Type-XI (for National Highways and State Highways)

C) Made of Class-A High Intensity Micro Prismatic Grade Sheeting of Type I (for ODR & Village Roads)

8.31 Rumble Strips (Provision of numbers of rumble strips covered with premix bituminous carpet, 15-20 mm high at center, 250 mm wide placed at 1 m center to center at approved locations to control speed, marked with white strips of road marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface)

8.13 Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)

8.55 Providing and fixing Raised Pavement Markers made of polycarbonate ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 Kg tested in accordance to ASTM D 4280 type H and complying to specifications of category A of MORT&H (RW/NH-33023/10/97-DO III Dtd. 11.06.1997). The pavement markers will be auto moulded by dual polymer shanks and must comply with all the MoRT&H specifications. The height, width and length shall not exceed 50 mm, 100 mm and 100 mm respectively and with minimum reflective area of 13 Sq.cm. on each side and slope to the base shall be 35 +/-5 degree. The strength of detachment of the integrated cylindrical shanks (of diameter not less than 19 +/- 2 mm and height not less than 30 +/- 2 mm) from the body is to be a minimum value of 500 kgf. Fixing will be by drilling holes on road for the shanks to go inside, without nails and using epoxy resin based adhesive and complete as directed by the Engineer-in-charge.

8.61 Providing and fixing Solar Blinker Light 300 mm dia, LED Aspect made of FRP/Poly arbonate with battery backup fitted on 150 mm dia MS pipe - 3.0 metre long from the ground level, firmly fixed to the ground by mean of properly designed foundation with M-15 grade cement concrete 60cm x 60cm x 60cm, below ground level.

Sub total

Add GST@18%