Department Of Rural Development And Panchayats Tender

Single Bed for Rooms Supply of Single Bed with Mattress and Pillow whose bed Overall Size : Length - 2060.0 mm,Width - 1131.0 ram Height - 930.0 mm. Material: Bed Structure consist of metal frames made of M.S. Channels in 1.0 mm Thickness. Horizontal plinths and bottom plinth are made of 25 mm Thick Prelaminated Particle Board. Head board is made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims fixed to it. Tail board is made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims fixed to it. Side rail is made of 18 mm thick Prelaminated Particle board with imported H.D.F. foil wrapped decorative trims fixed on to it. Mattress panels of Bed are made of 18 mm thick Prelaminated Particle Board with all the exposed edges are edge banded with 0.8 mm thick PVC edge banding. Construction : Knock Down construction. Finish : 18 mm thick Prelaminated Particle Board is in Walnut shade. Metal frames are powder coated in shade Mat Black to the thickness of 50 microns(+-10).The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Single sided Book rack Supplying of All Steel Periodical Display Rack whose Overall Dimensions shall be 900mm(W)x450mm(D)x1830mm(H). Rigid Knockdown construction ,Panels shall be made from CRCA 0.6 mm thick and front frame shall be made from CRCA 0.8 mm thick . CRCA D grade as per IS 513 . There shall be 5 level racks , Display tray shall be suitable for fullscape size magazines,periodicals, aesthetically appealing metal tray at an angle for easy viewing . Receding facility to access the storage behind . Sliding on plastic rollers . Behind storage shelving each of 5 level has a behind storage shelf . Uniformly Distributed Load capacity per each shelf is 40 kg . Leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns.The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Conference HB Chair Supplying of the conference High Back chair whose seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 76.0Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a fixed type M.S tubular armrest support chrome plated. The Arm support has static vertical adjustment of +/-1.5+/-0.05cm. The mechanism of the chair shall have following features : 360⁰ revolving type, Front pivot synchro mechanism, Tilt tension adjustment, Single point control, 4 position locking with anti shock feature, Seat/Back tilting ratio of 1:2. The backrest shall consist of a fixed type mechanism i.e no back up/down adjustment. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestial shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap. The size of the pedestal shall be 66.0+/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be made black nylon. Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0cm as measured from pedestal below. Height from ground - min 102.5 to max 111.5cm. Seat height - min 46.0 to max 55.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Conference MB Chair Supplying of the Conference Mid Back chair whose seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 64.5Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a fixed type M.S tubular armrest support chrome plated. The Arm support has static vertical adjustment of +/-1.5+/-0.05cm. The mechanism of the chair shall have following features : 360⁰ revolving type, Front pivot synchro mechanism, Tilt tension adjustment, Single point control, 4 position locking with anti shock feature, Seat/Back tilting ratio of 1:2. The backrest shall consist of a fixed type mechanism i.e no back up/down adjustment. The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestial shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap. The size of the pedestal shall be 66.0+/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be made black nylon. Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0cm as measured from pedestal below. Height from ground - min 91.0 to max 100.0cm. Seat height - min 46.0 to max 55.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. 46.0 to max 55.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Conference Visitor Chair The seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/-0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 64.5Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a fixed type M.S tubular armrest support chrome plated. The Arm support has static vertical adjustment of +/-1.5+/-0.05cm. The backrest shall consist of a fixed type mechanism i.e no back up/down adjustment. The leg frame welded assembly shall be chrome plated, made from 3.5+/-0.03cm x 1.5+/-0.02cm x 0.16+/-0.0128cm thick ellipitical MSERW tube and provided with a base plate for seat fixing. Overall dimensions of Chair shall be, Width of Chair - 66.5cm, Depth of Chair - 58.0cm as measured from pedestal below. Height from ground - 88.5cm. Seat height - 45.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Chiar for Superintending engineer Supplying of High Back chair whose seat & back is made up of 1.2 ± 0.1cm thk. Hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18; upholstered with synthetic leather over moulded High Resilience Polyurethane foam. HIGH BACK SIZE: 51.8 cm. (W) x 75.2 cm. (H) SEAT SIZE: 49.0 cm. (W) x 51.4 cm. (D). The HR polyurethane foam is moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS: 7888 for 25% compression. The adjustable armrest is designed with the following features: Up-Down adjustment– 8 steps (8.0±0.5cm range) . Height adjustable armrest structure which is chrome plated & fitted with an armrest top. Fixed Armrest Top is PU moulded over metal insert. The adjustable tilting mechanism is designed with the following features. 360° revolving type. Single point control. Front-pivot for tilt with feet resting on ground ensuring more comfort. Tilt tension adjustment. 4-position locking with anti-shock feature. Seat/back tilting ratio of 1:2. Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for for High back and mid back chair. The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. Pitch-center dia. (75.0 ± 1.0cm. With castors). The twin wheel castors are injection moulded in black PP. Seat can be slide horizontally as per user convenience. Stroke of seat slide is 5 cm. This option is available for revolving pedestal type of chair. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Visitor chair for Superintending engineer Visitor Supplying of Vistor chair whose seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood Measured as per QA method described in OCP-QLTA-PL14-18; upholstered with synthetic Leather over moulded High Resilience Polyurethane foam. WIDTH (W : 57.5 CM DEPTH (D): 58.2 CM HEIGHT (H): 100.8 CM. SEAT HEIGHT (SH): 47.0 CM. The tubular frame is powder coated (DFT 40-60 microns) cantilever structure & made of Dia. Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the frame assembly. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Chair for GIS Supplying of High Back Chair whose SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE 47.5 cm. (W) x 69.5 cm (H) SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO mechanism: The mechanism should be designed with the following features: 360° revolving type. Upright-position locking. Tilt tension adjustment. Seat/back tilting ratio of 1:3. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.TELESCOPIC BELLOW ASSEMBLYThe bellow should be 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY:The pedestal should be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). TWIN WHEEL CASTORS:The twin wheel castors should be injection moulded in Black Nylon. Overall Dimensions of Chair. Seat Height - min 42.5 to max 54.5cm. Height - min97.0 to max 109.0cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Chair for Supervisor Supplying of Mid Back Chair having SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal area. BACK SIZE 47.5 cm. (W) x58.0 cm (H) SEAT SIZE 47.0 cm. (W) x 48.0 cm. (D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS :The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. CENTER TILT SYNCHRO mechanism: The mechanism should be designed with the following features: • 360° revolving type. • Upright-position locking • Tilt tension adjustment • Seat/back tilting ratio of 1:3. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLYThe bellow should be 3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY:The pedestal should be injection moulded in black 33% glass-filled Nylon-66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). TWIN WHEEL CASTORS:The twin wheel castors should be injection moulded in Black Nylon. Overall Dimensions of Chair Seat Height - min 42.5 to max 54.5cm. Height - min85.5 to max 97.5cm. Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Visitor Chair for GIS/ Supervisor Supplying of Visitor chair having SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured lumbar support for extra comfort. The seat has extra thick foam on front edge to give comfort to popliteal should be a BACK SIZE 47.5 cm. (W) x58.0 cm (H), SEAT SIZE 47.0 cm. (W) x 48.0 cm (D). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. 3. 3.ARMRESTS :The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. TUBULAR FRAME: The powder coated ( DFT 40-60 microns ) tubular frame should be cantilever type & made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of Chair Seat Height - 46.5cm. Height - 89.5cm. Width & Depth of Chair as measured from pedestal - Width-61.4 cm and Depth-64.5 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Computer Table Supplying of Computer Table having (W)90*(D)59*(H)74.5m Wire Mesh Tray : MS Bright Bar Ø 8.0 & Ø 4.0 Vertical Cover MS CRCA sheet 0.8 thick CPU Stand: MS ERW Tube Ø 25.4 x 1.25 thick. Leg: MS ERW Tube 1.6 thick Foot Rest : MS CRCA Sheet 1.2 Raw Material : PLB top. PLB: 25 mm for table top with 2.0 mm thick PVC lipping Metal Parts: MS ERW Tube , MS CRCA sheets & MS Bright Bar. Hardware : Nut & Bolts , 5 Glide screws ,Self Tapping Screws & Articulated KBPT. Construction:Knock down fitting. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Chair for Computer Table Supplying of Chair whose SEAT/BACK ASSEMBLY: The seat and back should be made from 1.0±0.1cm. thk. hot pressed moshould be ture resistant tant.commercial plywood and upholstered with P.U. foam and fabric. BACK SIZE: 42.0cm. (W) X 26.5cm. (H) SEAT SIZE: 42.0cm. (W) X 42.0cm. (D). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR Polyurethane foam should be moulded with density =45+1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression. UNDERSTRUCTURE ASSEMBLY: The understructure assembly should be a cantilever type mainframe made of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated--( DFT 40-60 microns ). ARMREST ASSEMBLY: The armrests should be made in twin tube form using 0 1.58cm. (5/8") x 0.16 ±0.0128cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns ). Overall Dimensions of Chair: Seat Height - 46.0 cm. Height - 82.5cm. Width & Depth of Chair as measured from base - Width-54.0cm and Depth-59.5 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Cabin table with ERU Supplying of Cabin Table having 2350mm x2350mm x750mm Primary Work Surface Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Soft closing access flap with in-build power box are provided on work surface for wire management. Modesty Panel Made of 25mm thick MDF one side laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Under- structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal- Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Pedestal construction is BOX-BOX-FILE type which Uses powder coated. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Cabin Back Unit Supplying of Cabin Back unit having Top Panel: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Slide Door Unit: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. Display/Storage Unit. Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side,back and shelves. Doors are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Top panel of display unit Made of 25mm thick MDF one side pre-laminate board confirmin to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Chair for Reception/ Cabin Staff Supplying of mid back chair having SEAT/BACK ASSEMBLY: The seat and back should be made from 1.2 ±0.1 cm.. thk. hot pressed plywood method described in. and upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam should be designed with contoured lumbar support for extra comfort. SEAT SIZE: 45.0cm(W) x 42.0cm.(D). BACK SIZE: 40.0cm(W) x 47.0cm.(H). SEAT /BACK COVERS: The seat and back covers should be injection moulded in black Co-polymer Polypropylene. HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR polyurethane foam should be moulded with density 4+/ -21(g/neand_ hardness load 16_± 2 kgf for 25%_compression 4. ARMREST ASSEMBLY (FOR 7046R): The one-piece armrests should be injection moulded from black Nylon. The armrests should be fitted to the seat with armrest connecting brackets made of 0.5 ± 0.05 cm. thk. HR steel. PERMANENT CONTACT mechanism: The permanent contact mechanism should be designed with the following features• 360° revolving type.• 14° ±2°maximum-back-tilt-only.• Upright position locking.• Tilt tension adjustment. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm. TELESCOPIC BELLOW ASSEMBLY: The bellow should be .3 piece telescopic type and injection moulded in black Polypropylene. PEDESTAL ASSEMBLY: The pedestal should be injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal should be 62.0 ±0.5cm. pitch-centre dia. (72.0 ±1.0cm with castors). TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon. Overall Dimensions of Chair. Seat Height - min 43.0 to max 54.0cm. Height - min87.5 to max 98.5cm. Width & Depth of Chair as measured from pedestal - Width-71.0 cm and Depth-71.0 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Chair for Reading table Supplying of Chair for reading having SEAT/BACK ASSEMBLY: The seat made from 1.2 ±0.1cm. thk. hot pressed plywood measured and back should be injection moulded from black Co-polymer Polypropylene upholstered with fabric and moulded Polyurethane foam together with seat and back covers. The back foam should be designed with contoured lumbar support for extra comfort. SEAT SIZE: 45.0cm(W) x 42.0cm.(D) BACK SIZE: 39.0cm(W) x 38.0cm.(H) SEAT I BACK COVERS: The seat and back covers should be injection moulded in black Co-polymer Polypropylene. HIGH RESILIENCE (HR)POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45 +/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. 4. ARMREST ASSEMBLY (FOR 7044T): The armrests should be made of black integral skin Polyurethane wtih 50-70 Shore 'A' Hardness and reinforced with M.S. insert. The P.U. armrests should be then fixed to black powder-coated ( OFT 40-60 microns ) armrest brackets made of of 0.5 ± 0.05 cm. thk. HR steel and fitted with claddings made of injection moulded Polypropylene. FIXED TYPE mechanism: The fixed type mechanism should be without back tilt. TUBULAR FRAME: The tubular frame should be made up of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. tube and black powder coated ( DFT 40-60 microns) Overall Dimensions of Chair Seat Height -49.5cm. Height -88.5cm. Width & Depth of Chair as measured from pedestal - Width-56.0 cm and Depth-54.0 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Conference Table Supplying of Conference Table size shall be seats ( 1) 675 Width mm x 600 D epth mm x 750 Height mm , seats (2) 1350 Width mm x 600 Depth mm x 750 Height mm . Top shall be 25 mm PLB thick With PVC beading all over . In Understructure legs shall be made from 18 mm thick PLT having curved profile plus Modesty shall be made from PLT (pre - laminated twin ) boards 18 mm thick in two shades . Wire manager shall be running along the width of desk fitted on the modesty panel from inside. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Table for Supervisor/ Staff Supplying ofTable without CPU Hanger size shall be 1200 Width mm x 600 Depth mm x 728 Height mm. Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) . The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Single Bed for Hall Supplying of Single sided bed of MATERIALS & DIMENSION (+/- 5mm)Code Dimension (mm) Code Dimension (mm) Code Dimension (mm)A= 2080 B= 840 C= 925 D= 385 BED -METAL FRAME MATERIALS & DIMENSIONS:(gauge +/- 0.1mm). M.S. PIPE 25.4x 50.8 x 1.2 THK.;M.S. PIPE 19.05x 19.05 x 0.8 THK.;M.S.ANGLE 20x20x1.6 THK; M.S. PIPE DIA. 50.8 x 0.9 THK.;M.S. PIPE DIA. 15.875 x 0.8 THK.;DECORATION MATERIALS & SPECIFICATIONS: (DENSITY / TYPE) Color : Black RECOMMENDED MATRESS SIZE: 78" X 36" POWDER COATING COLOR & DFT IN MICRONS: Black DFT= 50-60 Microns PACKING SPECS : 1 Cartons Head , Foot & Bedstead Carton size: 1994mm X 933mm X 95mm Qty : 1 pieces per carton (1 of 1) 7ply. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Table for Superintending engineer Supplying of Table whose size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. ERU size shall be 1050 Width x 450 Depth x 705 Height. The top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Corner Table Supplying of Corner Table having (W)60*(D)60*(H)45 table legs meterials & size : oval metal tube thick-1.5 mm color : silver power coating table top materials & size : (density / type) l x w x t -1100 x 600 x 8 mm full black tempered glass table bottom materials & size : (density / type)l x w x t-1100 x 600 x 6 mm color : full black tempered glass. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Cabin corner table Supplying of Cabin Corner Table having (W)55*(D)55*(H)50. Table legs meterial : metal round tube-The helix coffee table Top is Made up of Toughened Glass and the leg is made up of Chrome Palted Undresturure color : partial black color: full black bottom finishing: black top and chrome frame and legs. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Main Cabin table with ERU Supplying of Main table which shall be of size 1800 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Main Cabin Back Unit Supplying of the Back unit which shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Supplying of 1800 W size which shall be 1800 Width mm x 900 Depth mm x 740 Height mm . The top shall be 25 mm thick PLB with 2 mm thick PVC Edge Beading plus the Understructure shall be having C - Frames 1.6 mm thick MS supporting the top . The Legs shall be of dia. 38.1 x 1.6 mm thick MS ERW tube. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Main Cabin High Back Chair Supplying of Premium high back Chair having SEAT ASSEMBLY : The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D) BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather.*HIGH BACK SIZE : 47.5 cm. (W) x 77 cm. (D) ARMRESTS : The armrest top is moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM (FU3201,FU3202): The adjustable ting mechanism is designed with the following features: • 360° revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position.• 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing is made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT (FU 3201/FU3202): Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm. Back Frame is connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.). 5 Nos. twin wheel castors are injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Visitor Chair for Main Cabin Supplying of Premium Visitor chair of SEAT ASSEMBLY : The Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D) BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather.The armrest top is moulded from polyurethane(PU), upholstered in pure leather and mounted on to tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish. VISITOR TUBULAR FRAME (FU3212) : The tubular frame is cantilever type & made of 02.54±0.03 cm x 0.2±0.016 cm thk S.S 202 tube.The back connected to frame through chrome plated high pressure die cast connector piece. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Cabin High Back Chair Supplying of High Back Chair of Cushioned seat is made of Injection molded Plastic outer & inner. Plastic Inner is upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression.*Seat SIZE: 47.0 cm. (W) x 48.0 cm. (D) BACK ASSEMBLY: The Cushioned back is made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. *HIGH BACK SIZE: 47.7 cm. (W) x 76.4 cm The armrest top is moulded from polyurethane (PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish. The armrest height adjustable up to 6.5±0.5cm in 5 steps. The adjustable tilting mechanism is designed with the following features: 360’ revolving type. Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. Tilt tension adjustment can be operated in seating position.5-position Tilt limiter giving option of variable tilt angle to the chair. Seat/back tilting ratio of 1: 2The mechanism housing is made up of HPDC Aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5 cm. Back Frame is connected to the Up/down mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. Pitch-center dia. (75.0 ± 1.0cm. With castors.) The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Visitor Chair for Cabin Supplying of the Visitor chair whose Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. BACK SIZE: 47.7 cm. (W) x 60.1 cm. (D) The tubular frame should be cantilever type and made of Ø2.54± 0.03 cm X 0.02 ± 0.016cm thick SS 202 tube. The back should be connected to frame through chrome plated high pressure die case connector piece. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Chair for workstation (Big Staff Room) Supplying of the Executive Mid back Chair:The chair seat shall be made up of 1.2 +/- 0 .1 cm. thick hot pressed plywood measured .. The back assembly shall be made up of powder coated (DFT 40-60 microns) tubular frame of ida 2.54 +/- 0.03 cm. X 0.2 +/- 0.016 cm thick. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. Seat size: 47.0 cm(W) X 48.0 cm(D). BACK SIZE: 46.5 cm(W) X 60.5 cm(H). HIGH RESILIENCE (HR) POLYURETHANE FOAM : The HR Polyurethane foam is moulded with 45 +/- 2 kg/m^3 and Hardness 16 +/- 2 kgf as per IS: 7888 for 25% compression. ARMRESTS: The armrests shall be one- piece armrests are injection moulded form black Co- Polymer Polypropylene.CENTRE TILT SYNCRO MECHANISM: The mechanism shall be designed with the following features: 360° revolving type, Upright position locking , Seat/back tilting ratio of 1:3 & Tilt tension adjustment (6 DEG SEAT TILT/18 DEG BACK TILT). PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment shall have an adjustment stroke of 11.0 +/- 0.3 cm. TELESCOPIC BELLOW ASSEMBLY: The bellow shall be 3-piece telescopic type and it is injection moulded in black Polypropylene. PEDESTAL ASSEMBLY: The pedestal is injected moulded in black 33% glass filled Nylon -66 and fitted with 5 twin wheel castors. The pedestal shall be 66.3cm. pitch-centre dia. (76.3 cm with castors). TWIN WHEEL CASTORS: The twin wheel castors are injection moulded in Black Nylon.Seat Size: 47.0 cm(W) x 48.0 cm(D) Back size 46.5 cm(W) x 60.5cm(H). The product must be either BIFMA Level or Greenguard certified. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Supplying of 2 seater sofa-134cm(w)*87cm(d)*78cm(h)*43cm(sh). STITCHING: THREAD : Poly Proplin, PVC. Thickness (mm) : 0.9. Weight (GSM) : 575. FRAME MATERIAL Moisture Content ( 10 – 12 %) : 16-20%. Thickness of Plywood used(mm) : 12mm & 18mm. SEAT FOAM: (DENSITY, TYPE)-Thickness (mm) : 69, 22 & 10 mm. Density (Kg/m3)- 32d. Type of Foam : Vergin Always / in some case Moulded - Dencity :- 48d. LEG MATERIAL: * Fixing of Leg : Woodscrew provided on frame in addition to M-8 / T-Nut * Material of leg - Plastic * Bush for Leg bottom : Pvc. Bush .BACK FOAM: (DENSITY, TYPE) -Thickness (mm) : 45 mm .Density (Kg/m3): 28 d .ARMREST FOAM: (DENSITY, TYPE) Thickness (mm) : 45 mm .Density (Kg/m3): 26 d . The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Two seater Sofa for Cabin Supplying of 2 seater sofa whose seat is made of PU ‎foam with Density ‎28‎± ‎2 ‎kg‎/‎cu‎.‎mtr having an ‎additional top layer of super soft ‎PU foam in Density ‎32 ‎± ‎2 ‎kg‎/‎cu‎. ‎upholstered with fabric ‎or leatherette‎. ‎ ‎The back is ‎made of PU foam with ‎Density ‎28 ‎± ‎2 ‎kg‎/‎cu‎. Mtr with two additional ‎top layer of super soft ‎ foam of density ‎32‎±‎2 ‎kg‎/‎cu‎. ‎mtr. ‎upholstered ‎ with fabric or leatherette .‎Under structure is made ‎up of ‎1‎.‎2‎±‎0‎.‎1 ‎cm‎. ‎thick ‎hot pressed plywood ‎( moisture resistance & termite proof as per IS: 303) & pinewood of cross section devoid of major knots & surface defects 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over under structure for cushioning purpose 6 nos. per seat & 3.8 mm Dia zigzag spring assembly is mounted over under structure for cushioning purpose. ‎It is ‎a welded assembly ‎made in Stainless steel ‎(‎grade SS ‎202‎) ‎tube ‎& ‎plate‎ with plastic endcap. (W) 146.0* (D) 90.5(H) 85.5 cm seat (H) 45.0 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

2 seater Visitor Sofa Supplying of 2 seater visitor Sofa of SIDE FRAME ASSEMBLY: The side frame assembly should be fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It should be made of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cmx0.16cnn and black powder coated ( DFT 40-60 microns ). The ends should be fitted with ABS moulded end caps. TIE MEMBER: It should be the connecting beam assy. which holds the two side frames to each other. 2 nos. tie members should be used to connect the side frames. The tie-member should be of 0 3.81 ±0.03cm. x 0.2 ±0.016cm. thick cm x 0.16cm and black powder coated ( DFT 40-60 microns ). The seat/back assemblies should be mounted on one of the tie-member which has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5 ±0.1cm. thk -- 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back. SEATREST ASSEMBLY:The seat rest assembly consshould be ts of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 25 ± 2 kgf for 25% compression of the foam. The complete moulded seat rest assembly should be covered with a replaceable fabric upholstery cover *SEAT SIZE: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T) BACKREST ASSEMBLY:The backrest assembly should be flexing type and consshould be ts of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 +1- 2 Kg/m3 with Hardness load 14 ± 2 kgf for 25% compression of the foam. The complete moulded backrest assembly should be covered with a replaceable fabric upholstery cover. *BACK SIZE: 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) ADJ. GLIDES: The adj. glide should be injection moulded in black Nylon & fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take cshould be or unleveled floor surface.Overall Dimensions of Chair.Seat Height - 43.5 cm. Height - 78.5cm. Width & Depth of Chair as - Width-113.0cm and Depth-70.0 cm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Table for Pantry Supplying of the table having worktop of Stainless steel brushed finish with PLB insert for durability. The side frames should be made from 30mm X 30mm X1.5mm thick M.S Powder coated. Tubes at base which are welded and are fixed to top with screws and MS Shade shall be S/G Mettalic Dark Grey (Nerocoat -9000626). The cross member should be Made from 30mm x 30mm x 1.5mm thick M.S Powder coated tube,Which is welded and bolted to side frames. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Steel Almirah Supplying of Almirah which shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). P. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Table for GIS Supplying of Main Desk size shall be 1500 Width x 750 Depth x 743 Height.Top shall be of 18 mm thickness made of PLT board with 2 mm Edge banding. Wenge and savannah Maple PLT board shall be used. The Understructure shall be in pre-laminated panels made with PLT boards . 2- Drawerand 3 - Drawer storage units with different combinations to support tops made with 18 mm PLT boards of different colours.Modesty and back panels made with 18 mm PLT boards. The pedestals / storages shall be fitted with necessary locks. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Chair for Pantry Supplying of canteen chair with Seat back is one piece injection moulded in polypropylene. The approximate Seat Size is 43.0cm (W) X 35.0cm (D) & approximate Back Size is 41.0cm (W) X 40.0cm (H). The Tubular understructure is fabricated from 19.0 X 1 mm thk SS 202 Grade tube welded together with SS connecting rod 8.0mm. The understructured is provided with black PP injection moulded ferrules. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Back Unit/ Storage for GIS Supplying of Vertical sliding Door Unit which shall be 900mm(W)x450mm(D)x1192.5mm(H) .The top shall be wooden top PLB(25 mm add in unit height ) . The Rigid Knock Down Construction , Back , Sides and Door shall be made from 0.7 mm high yield strength CRCA ,rest in 0.8 mm CRCA . CRCA - 'D' Grade as per IS-513 . Sliding door arrangement shall have sliding door wth top hanging arrangement to prevent derailment . Each door shall be provided with 2 plastic roller having steel ball bearing for smooth movement of door & less noise . Locking shall be 5 lever cam lock for safe locking . Handle shall be plastic flush & recessed handle . Shelving shall have Height wise adjustable shelf mounting . Uniformly Distributed Load Capacity of the shelf is 40 Kg maximum . VSDU shall have 2 no. of adjustable full shelves . Accessories optional shall be cradle with pipes for hanging godrej instadex files . Leveler shall be screw type leveler with hex plastic base and overall finish shall be epoxy polyester coated to the thickness of 50 microns . For VSDU A4 size box file can be stored vertically on two shelves and clear space above third shelf is 295 mm. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.

Workstation 4ft Supplying of modular Work station should be a panel based system of size 1200mm x 600mm that manages to look slim yet strong. It should be having a gapless partition system with linear panel for contemporary look. The workstation should be elevated from the ground for more air circulation with efficient wire management. The Thickness should be 52.4mm and this panel comprises of of 2 nos of vertical extrusions made of Aluminium. Horizontal extrusions made of Aluminum at every division of tile/blocks. Numbers of extrusions vary as per panel height. Blocks made of composite construction of MDf and paper honeycomb and it varies as per height. 1 number of fabricatedbottom frame as a welded structure of steel components. 2 nos of Bottom Tiles and 2 nos of top tiles.1 no. of top trim made of Aluminum extrusions. The panel leg used for supporting panels with height adjustability upto 50mm provided by leveler. Full Side Panel with Bracket would be in 25mm thk PLT mounted with full gable end braket made from 1.2 mm thk MS CRCA Grade D as per IS:513. Worktop should be of 25mm thk PPB with 2 mm thk machine pressed PVC Lipping with hot melt EVA glue.3 Drawer Pedestal It should have multi bend construction with welded body and “Over Closing” style. Body shell, Drawer front and trays, Front side stiffener to be made from 0.6 mm thick MS CRCA Grade D. Top and bottom stiffeners to be made from 1.2 mm thick CRCA sheet. Rear side stiffener to be made from 0.8 mm CRCA sheet. It should have 10 lever cam lock. . It should have anti tilt mechanism and anti rebound mechanism. All steel components should undergo eight tank anti rust treatment and oven baked epoxy polyester powder coated with 50-60 dry film thickness. The CRCA steel sheet used should be as per IS-513 1994. Scratch hardness of 3 Kgs as BS-3900 part E2 1970, IS-101. Salt spray test of 1000 hrs. as IS 101. The metal tray is made of 0.9mm thick MS CRCA ‘D’ grade as per IS:513.CPU trolley on castors wheel will be part of each workstation. The tray should be made of 1mm thk MS CRCA sheet and side supports are made of 0.8mm thk MS CRCA sheet. Castors should be injection moulded in black nylon. The OEM must have ISO, BIFMA, OHSAS. Aprroved Make: Godrej, Haworth, Herman Miller, Steelcase & Knoll.