Department Of Rural Development And Panchayats Tender

Construction of unlined surface drains of average cross-sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3m and lead of 50 m (average lead 25 m) as per Technical Specification Clause 307.

Excavation in Cutting in Soil by manual means with lead upto 50 mExcavation for roadway in soil for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3 Earth Work Summary Sheet (B)

Construction of Embankment with Material Obtained from Roadway CuttingConstruction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 Earth Work Summary Sheet (H)

Construction of embankment with approved material obtained from borrow pits, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 (Beyond 250m)with all leads as per Technical Specification Clause 301.5(Having CBR more than 5) Earth Work Summary Sheet (J)

Construction of Subgrade and Earthen Shoulders Construction of sub-grade and earthen shoulders with approved material (Granular material having CBR not less than 7) obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification

Construction of granular sub-base by providing well graded material having CBR 20 or more, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory rollers of 80 to 100KN static weight to achieve the desired density, complete as per Technical Specification Clause 401. For Grading mentioned in table 400.1 (Grading III)

WMM Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406.

Construction of subgrade and earthen shoulders Construction of sub-grade and earthen shoulders with approved material (Granular material having CBR not less than 10) obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1.(To be used for side shoulder WBM)

Construction of un-reinforced, jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including leveling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying, primer, sealant, using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703

5 km Stone

Ordinary Kilometer Stone (Precast)

200 m stone (precast)

Boundary Pillar Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704

Providing & Laying Cement Concrete Pipe NP3 on first class bedding of granular material including fixing collar with cement sand mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonary work in head wall and parapets as per clause 1106 .(A) 600 mm dia

Cement concrete blocks of size as per Table 1300.2 cast in cement concrete of grade M 15 (a) Concrete grade M 15

Providing concrete for plain/reinforced concrete in open foundation complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

A Typical design of PMGSY information sign Board is shown in fig .1700.1 .The specifition and installation details of typical sign board are given below. The board will be a composite unit consisting of three plates of Alumininm Composite Materials (ACM), material specifications are per Clause 1701.3.7 The top most plate will be in diamond shape of 600 mn x 600 mm sizr, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size on back on edges. The middle plate will be 1200 mm 150 mm size riveted over welded rvr.s. angle iron frame of 25 mm x 25 nm x 5 mm size on back on edges. The main Iower most plate wiII be 1500 mn x 600 mm size, riveted over welded M.S. angle iron frame of 25 mm x 25 mm x 5 mm size welding of all the sheets over angle iron frame will be done neatly to have plain surface on one side. The angle iron frames of the lower most plate and the middle plate will be welded to two nos. 75 mm x 75 mm (12 SWG ) sheet tubes posts placed at 1125 mm apart centre to centre. The top of the middle plate wilt be flushed with the top of 75 nm dia medium steel tube posts and these posts will be embedded in cement concrete M 15 grade blocks of 450 mm x 450 mm x 600 mm below ground level. The height of bottom of the lower nost plate will be 1200 mm from normal ground level and the bottom of middle plate will be 100 mm above the top level of the lower most plate. The diamond shaped plate mounted over angle iron frame will be connected to middle plate by square medium steel section of 47 mm x 47 mm thickness 12 SWG having a spacing of 100 mm between the diamond shaped plate and middle plate and this square section will be welded to the bottom point of the diamond shaped plate. (ii) The lettering and borders etc. of middle and bottom plate, pMGSy logo on top plates shall be as per clause 1701.4.6 messages/Borders. All the section of frame and posts will be painted with primer and two coats of Epoxy paint The steel tube below ground level will be painted with three coats of Epoxy paint The design, painting and lettering shall be done as per approved drawing. (iii) For warranty and durability the clause 1701.5 and for maintenance the clause 1911 shall be applicable. (iv) A reference number along with the month and year of installation should be placed on the back of a sing in a contrasting colour or by stamping in characters not exceeding 50 mm in height.

Kilometre Stones & Boundary Pillar Direction and place identification signs up to 0.9 Sqm. sisn board Providing and erecting direction and place identification of Retro reflective sheeting classs A/ class B sign boards type IV as per IRC-67 made of 2 mm thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm width and required message, letters, figures with reflective tape of engineering grade as per MORI) specifications ofrequired shade and colour. Supported and welded on two nos.47 mm x 47 mm of 12 SWG square tube of 3050 mm height duty strengthened by 25 mm x 5 mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mmr 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Excavation for Structure as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specification Clause 802,803,1202 & 1203 II. P.C.C grade M 15(Nominal mix (1:2.5:5)

Providing concrete for plain/reinforced concrete in substructure complete as per drawings and technical specification Clause 802,804,805,806,807,1202 & 1204, P.C.C. grade M15, (I) Nominal Mix 1:2.5:5

Providing and laying concrete for reinforced cement concrete in superstructure as per drawing and technical specification Clause 800,1205.4 & 1205.5 R.C.C. grade M 25 For Abutment Cap

Providing and laying concrete for reinforced cement concrete in superstructure as per drawing and technical specification Clause 800,1205.4 & 1205.5 R.C.C. grade M 25 For Slab

Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 ii)Sandy Material

Providing and fixing 20 mm thick compressible fibre board in expansion joint complete as per drawing and technical specifications

Providing weepholes in brick masonry/stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Drainage spouts complete as per drawing and technical specifications Clause 1209

Maintenance

1st Year Maintenance @ 30000 Rs/KM

2nd Year Maintenance @ 40000 Rs/KM

3rd Year Maintenance @ 70000 Rs/KM

4th Year Maintenance @ 110000 Rs/KM

5th Year Maintenance @ 150000 Rs/KM

Assistant Engineer PIU,CGRRDA NARAYANPUR

Flexible pavement

Rigid pavement

Protection Work

CD Works