Municipal Corporation Tender

Supply & Laying of DWC pipe 51/63mm with hand bockey:- Supply and Laying of pipe (OD-63 mm & ID-51 mm nominal) Double Wall Corrugated (DWC) With Hand Bockey High Density Polyethylene pipe ISI marked (HDPE Density 240 to 958 KG/Cm3) having corrugation on the outer wall and plain surface inner wall with average wall thickness for outer layer as 1.1+0.1mm and for inside layer 1.2+0.1mm maintenance free, ‘C’ value over 150 with lowest frictional losses, good weathering resistance, with all accessories like socket, bend, couplers etc. conforming to IS 14930,/ IS-16205 part ii complete with fitting and cutting, jointing etc.direct in ground (depth as per the directions of Engineer in charge or upto 75cm below ground level) including excavation and refilling the trench but including sand cushioning and protective covering etc., complete as required and PSEN-50086 (P-I & II) Make Gemini, Rex, Duraline The entire satisfaction of Engineer-in-Charge of work.

Supply & Laying of DWC pipe 51/63mm without hand bockey:- Supply and Laying of pipe (OD-63 mm & ID-51 mm nominal) Double Wall Corrugated (DWC) Without Hand Bockey High Density Polyethylene pipe ISI marked (HDPE Density 240 to 958 KG/Cm3) having corrugation on the outer wall and plain surface inner wall with average wall thickness for outer layer as 1.1+0.1mm and for inside layer 1.2+0.1mm maintenance free, ‘C’ value over 150 with lowest frictional losses, good weathering resistance, with all accessories like socket, bend, couplers etc. conforming to IS 14930, /IS-16205complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling of digging including sand cushioning and protective covering etc., complete as required and PSEN-50086 (P-I & II) of Make Gemini, Rex, Duraline. The entire satisfaction of Engineer-in-Charge of work.

G.I. Earth pipe electrode with salt/ Charcoal: Supply and laying of earth electrode made out of ISI marked 'B' class earthing with G.I. earth pipe 4.5 mtr long, 40mm dia including accessories, G.I. pipe electrode shall be cut tapered at the bottom, and provided with holes of 12mm dia, drilled not less than 7.5 cm from each other upto 2 Mtr. of length from bottom (with charcoal or coke and salt). The earth electode shall be laid in ground after boring as per CPWD specifications complete in all respect and to the entire satisfaction of the engineer-in-charge.

P/F 6 SWG GI earth wire in pipe: Providing & laying earth connection from earth electrode with 6 SWG dia G.I. wire in 15 mm dia G.I. pipe from earth electrode, as required.

Supply & Erection of PVC Insulated sheathed) Copper Conductor Cable ISI marked size 3 core 2.5 mm2. Supply & Erection of ISI Marked PVC insulated 3 core 2.5mm2 cable of Copper Conductor (Sheathed) make Universal/ Finolex/ Lapp/ Polycab/ Havell's/ left bare/ Sunhome in pipe of suitable size excluding cost and erection of pipe/pole etc. (i) Cable size 3 core 2.5 mm2 Copper Conductor 1100 Volts Grade. The work shall be executed to the entire satisfaction of Engineer-in-charge.

Supply & Erection of PVC Insulated sheathed) Copper Conductor Cable ISI marked size 3 core 1.5 mm2. Supply & Erection of ISI Marked PVC insulated 3 core 1.5mm2 cable of Copper Conductor (Sheathed) make Universal/ Finolex/ Lapp/ Polycab/ Havell's/ left bare/ sunhome in pipe of suitable size excluding cost and erection of pipe/pole etc. (i) Cable size 3 core 1.5 mm2 Copper Conductor 1100 Volts Grade. The work shall be executed to the entire satisfaction of Engineer-in-charge.

PAINTING & NUMBERING OF POLES 4.5/6 Mtr. LONG: - Painting of poles above ground level with two coats of black paint of Nerolec/Asian/ICI duly approved by the Engineer-in-charge. The pole surface should be cleaned well by removing dust/rust & other depositions & smoothened with the sand paper/Iron brush & proper filling be made before painting. For numbering of poles the base should be painted with yellow and the number should be written in black letters of 3” in length. The job includes all type of petty material require to complete the job to the entire satisfaction of Engineer-in-charge.

PAINTING & NUMBERING OF POLES 7.5/9 MTR. LONG: - Painting of poles above ground level with two coats of black paint of Nerolec/ Asian/ ICI duly approved by the Engineer-in-charge. The pole surface should be cleaned well by removing dust/ rust & other depositions & smoothened with the sand paper/Iron brush & proper filling be made before painting. For numbering of poles the base should be painted with yellow and the number should be written in black letters of 3” in length. The job includes all petty material require to complete the job to the entire satisfaction of Engineer-in-charge.

S&E of Outdoor type one side openable M.S. Cubical Pedestal of size 1200mmx 900mm x350mm fabricated from 16 G.M.S. sheet welded on M.S. angle iron frame of size 50mmx 50mm x6mm with 4 Nos. legs of angle iron of same size each of length 600mm with M.S. sheet of size 100mm x 100mm x 6mm thick at the bottom of the legs. The front side of the pedestal should be openable with hiunged door provided with Godrej type handle and L-key locking arrangements (with 2 sets of L-key). A 'U' type support made from M.S. sheet of 16 G having width 75mmx 6mm be welded vertically in the inner side of the door to avoid entry of water. The door of the pedestal should be provided with rubber gasket to avoid entry of other insects etc. The top of the pedestal shall be covered with canopy made out of 16 G M.S. sheet projected outside to avoid entry of water. Four No. supporting members each of size 50mm x 6mm thick according to cubical size shall be welded for mounting switcher gear i.e. ICTPN, BBC, Timer and energy meter etc. The Pedestal shall be painted with two coats of P.O. red paint after applying one coat of red oxide. One No. The legs of the pedestal shall be embedded in the 1:2:4 C.C. mixture by digging 1' deep pit of 1' dia.The letter 'M.C.C.' in 4" size shall be written on the front door of the Pedestal. The job also included supply and erection one no. wooden plank/ board of size 1’-6’’ x 1’-6’’ and 25mm thick suitable for fixing energy mater including cost of screw, nuts and bolts in cubical pedestal complete in all respect. The pedestal will be housed on RCC foundation platform of size 900mm deep (450mm underground and 450 mm above ground x 960 mm long x 410 mm wide including sufficient number of DWC pipe size of 51/63mm pieces to facility to entire the main cable and the circuit cable. The work shall be executed to the entire satisfaction of Engineer-in-Charge.

S&E of Sheet metal/iron clad Triple pole switch with neutral link 63 Amp.415 Volts. (with side handle) Supply & erection of 63 A/415 Volts ISI marked sheet metal iron clad switch of make Havells/ Standard/ L&T/ ABB/ Panasonic on existing surface with G.I. Bolts & Nuts/rag bolts and nuts etc., according to the size of holes in the body of the switch including bonding to the existing earth. The work shall be executed to the entire satisfaction of Engineer-in-Charge.

Supply & Erection of Three Phase Aluminum Bus Bar Supply & Erection of Three Phase Aluminum Bus Bar of size 300mmx25mmx5mm with L type fuse unit to be fixed on Porcelein insulators in the existing pedestal with required nuts, bolts & M.S. sheet. The fuse links should be equal to the number of out going circuits. The work shall be executed to the entire satisfaction of Engineer-in-Charge.

Supply & Erection of Three Phase Sensor based Timer and Contactor assembled in 22 gauge CRCA sheet enclosure duly powder coated with the following accessories (Three Phase) of Make Amsons/ L&T/ Scheinder or equivalent as approved by the Engineer-in-Charge. It shall conform to latest relevant IS Code:- 1. It shall have 3 contactors of capacity 40 Amp. Each of made BCH, Legrand, L&T or Siemons. The contractor should be of AC-3 duty 2 pole, 220/240 V coil Voltage. 2. It shall have Auto/Manual switch, light activated switching system with allied accessories as required. 3. It shall have kit-kat fuse unit of 40 Amp capacity. The fuse unit shall conform to latest relevant IS code for protection of timers, bakelite sheet & other components as per requirement as site. 4. It shall be housed in a powder coated 22 gauge M.S sheet cabinet fo its protection. 5.The device shall be provided/fixed in the existing pedestal box in such a way so that it operates at correct time i.e. at rising/setting of Sun. The Sensor shall be included time watch to operate as required. The work shall be executed to the entire satisfaction of Engineer-in-charge. Warranty:- IT SHOULD STAND WARRANTY FOR ONE YEAR TOWARDS ANY MANUFACTURING DEFECTS.

Supply and Erection of steel tubular pole 410 SP-6 conforming to IS-2713-1980, (Part 1 & II) having over all length of 7.5 Mtr and welded in 3 steps and having approximate Wt.92 Kgs with the followings:- a) The poll shall have cross-sectional length of 4.50,1.5,1.5 Mtrs., b) The out side dia and thickness shall be 114.3x5.40mm, 88.9x4.85mm and 76.1x3.25mm. c) The pole shall be erected 1.25mtrs. below the ground level in 8” internal ready made RCC muff. The gap between the pole and the muff shall be filled with the cement concrete 1:2:4. d) The cost includes all labour and material including carriage to the site of work. e) The bottom portion of the pole shall be painted with two coats of black paint after removing the dust/rust. The work shall be executed to the entire satisfaction of Engineer-in-Charge.

Wall Bracket:-S/E of 32mm dia x 1m long G.I. Pipe (Medium Class) Pole Arm/ Bracket for mounting LED Street Lighting/Fitting on pole including bending the pipe of the required shape (90 to 105 deg), 2 nos. required size (suitable for cemented and circular pole) Flat Iron Clamps with Nut, Bolts and Washer. GI Coatring/ Painting the flat iron with primer and finish paint as per relevant tender specifications.The bracket is to be fixed on wall with the help of MS clampsinculding welding and drilling of holes and complete in all respect incuding labour and other petty items required to complete in all job into the entire satisfaction of the Engineer-in -charge. Make the G.I. pipe should be of Tata/ Jindal/ Hissar or Ravindra.

Supply and Erection of Angle Iron of bracket of 3' long made out of Angle Iron of Size 35x35x6 & fixed on top of G.I. pipe (0.5) long 4'' dia angle to support the bracket complete in all respect with suitable clump and nuts/ bolts to the entire satisfaction of Engineer-in-charge.

Erection of 45 Watt Post tops Garden LED light on 4.5 mtr pole. The work shall be executed to the entire satisfaction of Engineer-in-Charge.

Erection of high power 25 Watt (Max) LED Street light on cemented pole/ wall baracket .The work shall be executed to the entire satisfaction of Engineer-in-Charge.

Erection of high power 200 Watt (Max) LED Flood Light luminaries on 7.5/9 /16/16 mtr high mast / High electric pole.The work shall be executed to the entire satisfaction of Engineer-in-Charge.