Chandigarh Industrial And Tourism Development Corporation Limited Tender

Two Burner Chinese Range:- Size :- 1650x1350x900mm • Working Top 16 G at 650mm with 16” high back splash in S.S Sheet 304 Grade with 3” wide flue riser & water channel complete with inverted type S.S drain cover connected to drain pipe. With stop cock arrangement . • Front sides & back Panelling made of 20/22 gauge S.S. sheet 304 Grade. • Frame Top and body secured to 38mm x 38mm x 3mm thick welded SS angle frame work. • 02 Nos Swivel type bib cocks with long handle. i/c making holes in the splash. • Heavy M.S Fire drums with Chinese Pan Supports. • High Pressure LPG T-35 burners , 70000 BTU / Hr. at 4.5 PSIG input pressure with individual control valve. • Each Burner with Pilot Burner & Control Valve. • 4 nos. 38mm dia S.S pipe legs with ss adjustable bullet feet. • 25mm Dia S.S. pipe under shelf.

Four Burner Continental Gas Range with under Counter Rack:- Size:- 900x900x850mm • #16Ga. S.S. Top. With front side turned down 50mm & in 12mm , rear & both sides turned down 50mm raw. • Top and body secured to 38mm x 38mm x 3mm thick welded ss angle frame work. • Exterior # 18 Ga. S.S. cladding. • 20 gauge 1 No. under shelf with openable door & handle arrangement below the range. • four (4) no. 350mm x 350mm Cast iron grate (Removable). • one (1) no. H.P. burner with separately pilot lamp., • three (3) no. L.P. burner with separately pilot lamp • two(2) no. # 18 Ga. S.S. drip tray with Integral handle. • Built in pressure Controller regulator. • Auto Ignition. •4 nos. 38mm diass pipe legs with ss adjustable bullet feet. •Gas connection of ½” 200000 BTU.

Continental Style grill Top:- ( For continental Kitchen) Size 450mmx750mmx 850+150mm

DISH LANDING TABLE WITH GARBAGE CHUTE:- Size 1800x675x850mm • #16 Ga. S.S. Top with part front & left side turned up 12mm @45deg turned down 62mm & in 12mm, • Remaining part front turned down 50mm raw. With field joint bolted at site.Rear & right side turned up 150mm returned 25mm & down 12mm Underside of the top shall be sound deadened. • Top and body secured to 12/25mm x 100mm x25/12mm # 1.6 mm Thick S.S. hat type welded channel frame work. • 4 no. 38mm Dia S.S. legs. With s.s. adjustable bullet feet. • 25mm Dia S.S. pipe cross bracing welded to ss legs rear & both sides , front side open. • One (1) no. 150mm dia x 100mm high garbage chute location as per plan.

STAINLESS STEEL SINK UNIT:- SIZE:- 600X750X850+150 • # 16 Ga. S.S Top W/ front & both sides turned down 50mm in 12mm. • 150 mm High Rear Side Splash. • Top & body Secured 38mmx 38mmx3mm Thick S.S welded angle frame work. • Unit with 1 No. 450mmx 450 mmx 300mm deep # 16 Ga. S.S sink, Sink complete with 50mm dia lever handle operated waste outlet & rear connected over flow 25mm dia. • 25mm dia SS pipe cross bracing rear & both sides front side open. • 4 Nos. 32mm dia S.S legs position 3” away from tables ends. with adjustable S.S bullet feet

THREE SINK UNIT:- Size 2250x 750x850+150mm • #16 Ga. S.S. Top with front side turned up 12mm @45deg turned down 62mm & in 12mm, • Rear side turned up 150mm returned 25mm & down 12mm. • Left side turned down 50mm raw. , right side extends 25mm & down 12mm raw. • Underside of the top shall be sound deadened. Top and body secured to 12/25mm x 100mm x25/12mm # 1.6 mm Thick S.S. hat type welded channel frame work. • 4no. 38mm Dia S.S. legs. With s.s. adjustable bullet feet. • 25mm Dia S.S. pipe cross bracing welded to ss legs rear & both sides , front side open. • Three (3) nos. 600mm x600mm x 300mm # 16 Ga. S.S. wash sink. • Sink Complete with 50mm dia lever handle operated waste outlet of 1 ½” dia. & water connector for Hot & Cold Water & rear connected overflow. 20 ga. SS apron on both sides . • Punch hole as required

S.S POT RACK:- Size:-1500x600x1650mm) • Four (4) no. S.S. pipe shelves. • First shelf 300 A.F.F.,Second 900 A.F.F. Third shelf 1375mm A.F.F. & Fourth shelf at 1850mm A.F.F. • Shelf outer tube 32mm dia S.S. pipe with 25mm dia S.S pipe welded to outer tube at75 c/c. • Four (4) no. 38mm dia S.S. pipe upright on castor. • Four (4) no. 150mm dia Non marking rubberized castors wheel, two with brakes.

OVER HEAD SHELFS:- • Construction of 1’-0” deep over head shelves in various sizes in 18 Gauge S.S sheet 1” raw splash against wall, front turned down 1 ½” in ½” mounted at 5’-7” AFF 1” away from wall with 10” high with heavy S.S cantilevered brackets as per site requirements complete in all respects.

TROLLEY / STORAGE RACK. Size:- 900x600x1850mm # 18 ga pre-polished s/s 5 Shelves all sides turned out 1/2" @ 45 deg marine edges turned down 1 1/2" in 1/2", underside of shelves reinforced with # 16 ga 1" x 4" x 1" inverted s/s hat type channel four nos. 14 ga s/s 1 1/2" x 1 1/2" vertical square pipe uprights shelves welded to uprights at all four corners first shelf located at 1800mm AFF, second at 375mm above first shelf third shelf at 375mm above second shelf and remaining two equally spaced Four 5" diameter swivel castors of Rexello or equal make, two with brakes.

HAND WASH SINK UNIT:- Size 425x475x250+150mm Wall mounted hand wash sink unit. • S.S 304 constructions. • 150mm high rear splash back. • Round pressed bowl. • Depth of wash bowl: 150mm. • With hot & cold water mixer. Front & both sides 20 ga. SS apron. SPECIAL NOTE:- All Sheet/Pipe S.S. 304 Grade Pre-polished Plastic Coated.

WORK TABLE WITH TWO UNDER SHELVES:- • 16 Ga. Rear Splash 150mm thick.( As per drawings & requirements of kitchen layout coved ¾” radius with top turned out 1” down ½”) • All shelves reinforced with S.S inverted Hat type channel sound deadend& aluminum painted . • # 16 Ga. S.S Top. W/ front & both sides turned down 50mm & in 12mm • Rear side turned up 150mm, returned 25mm & down 12mm. • Top & body secured 38mmx 38mmx3mm thick S.S welded angle frame work. • Full width # 18 Ga. S.S Bottom & intermediate shelves W/ reinforcement hat type channel . • 4 Nos. 38mm dia S.S legs position 3” away from tables ends. with adjustable S.S bullet feet. • All sheet/ Pipe S.S 304 Grade Pre-Polished Plastic Coated complete in all respects & complete as per specifications

Size :- 1050x750x850mm

Size:- 1200x750x850mm

Size:- 1500x600x850mm

WORK TABLE WITH SINK:- Size 1200X600X850mm • # 16 Ga. S.S Top W/ front & both sides turned down 50mmx in 12mm. • All shelves reinforced with S.S inverted Hat type channel sound deadened & aluminum painted • 150 mm High Rear Side Splash. ( As per drawings & requirements of kitchen layout coved ¾” radiush with top turned out 1” down ½”) • Top & body Secured 38mmx 38mmx3mm Thick S.S welded angle frame work. • Left of unit with 1 No. 450mmx 450 mm x 350mm deep # 16 Ga. S.S sink, Sink complete with 50mm dia lever handle operated waste outlet & rear connected over flow. • 25mm dia SS pipe cross bracing rear & both sides front side open. • 4 Nos. 38mm dia S.S legs position 3” away from tables ends. with adjustable S.S bullet feet

LOCAL EQUIPMENTS :- Manufacturing & or Supplying, Placing in position, Commissioning & Testing of Local Kitchen Equipment in proper & smooth working condition i/c handing over the same to the concerned authorities as follows:-

TANDOOR:- Commercial grade heavy duty tandoor of size 30”x30” x36” high 16g. S.S top secured to fully welded M.S angle frame work of required sizes reinforced of all sides and bottom and intermediate position exterior of base reinforced with inverted M.S channel heavy gazed frame work on all of four sides complete with 4 Nos 3” thick heavy duty nylon cast castors . The tandoors shall be insulated with tightly packed glass wool on sides and top and insulated with 2” thick commercial tandoor clay slab insulation at base. Exterior sides of 20 G S.S duly polished complete with top led to suit opening at top complete with top ring having provision for S.S shutter for removal of ash and S.S rods of size ½”x6” high welded to the frame work. Complete in all respects. (Clay Tandoor of Munni Lal/ Nand Lal / Prashadi Lal).

(FOUR DOOR REFRIGERATOR):- Dimension 52” X31"X79" high approx . Supply,Installation,Testing & Commissioning of reputed make Four Door Refrigerator s/s body with four doors both side imported door hinged at top and bottom pin hinges s/s rod handles, built in imported locking arrangement and magnetic gaskets top mounting compressor with louvered access panels forced draft air static cooling system 230V-50C-1 ph complete with independent control, digital thermometer and electric cord, built in voltage stabilizer with time delay auto start "- 2° C to +8° C temperature 0.5 HP comp. five pair removable S/S welded wire, adjustable height on s/s clips and s/s channels 2 1/4" thick PUF insulation castors provision front two with brakes switch activated lights for each compartment, wired common with housing panel bottom of internal storage pitched with 1" dia waste outlet and removable # 18 ga s/s perforated false bottom w/all sides turned down 1 1/2" and in 1/16" and slid out drip tray below waste outlet. Manufacturer :CELFROST / WILLIAM / ELANPRO

UNDER COUNTER REFRIGERATOR:- Dimension :70"X27"X33" high approx Supply,Installation,Testing & Commissioning of reputed make Under Counter Refrigerator 3 opening doors # 16 ga s/s pre-polished top all sides turned down 2" in 1/2" s/s body with three doors both side hinges with s/s handles, built in imported locking arrangement and magnetic gaskets, imported door hinged at top and bottom pin hinges right / left side compressor with louvered access panels forced draft air static cooling system 230V-50C-1 ph complete with independent control, digital thermometer and electric cord, built in voltage stabilizer with time relay auto start button of internal storage pitched with 1" dia brass waste on right side "-2 deg. C to +8 deg. C temperature 0.5 HP comp. #20 GA s/s cladding on all sides 2 1/4" thick PUF insulation all around 11/2" dia s/s counter type legs with s/s adj. bullet feet switch activated lights for each compartment, wired common with housing panel to operate on 230-50-1 ph electrical . The Unit further consist of 1 no. overhead S.S shelfs in 18 gauge duly insulated with Glass wool insulation supported over 4 Nos. 1” dia S.S pipes fixed to table top complete with 1 KW electric heating elements with Temp. Control, on – of Switch , Red light & control box operatable on A.C 230/50/1 supply. Manufacturer : CELFROST / WILLIAM VESTFROST/ ELANPRO

WATER COOLER WITH STABILIZERS:- Size :- 725x545x1150mm • Cooling Capacity 60 Ltrs./ Hr. • Storage Capacity 120 Ltrs. • Faucets 02 Nos • Refrigerant R-22 • Air Cooled Compressor • Operating on 230/50 Hz./1PH A.C Supply. • Voltage Stabilizers 2KW. • Body Stainless Steel . Plastic Legs . Make :- Celfrost/Blue Star/ Voltas

WET MASALA GRINDER:- (TILTING TYPE) #14 ga s/s grinding tank and overall s/s const. s/s stand with s/s adj. bullet feet s/s lever handle with complete tilting arrangement automatic water fill connection with float valve shut off all s/s const. suitably insulated and reinforced to be operate on AC 220/50/1 phase/ motor to be of reputed brand such as CROMPTON / KIRLOSKAR / SIEMENS etc. Make : RANS / LL EQUIPMENT/ CONTINENTAL/PRIDE.

SALAMANDER (WALL MOUNTED) Top:- With all standard details like counter balance lifting system, s/s removable tray #20 ga s/s body type frame with legs with heating elements of 3.0 KW mounted on bottom of top shelf with thermostate, indicating light, on-off switch mounted on right side of unit. Unit to have FRANKE type Salamander lifting system to operate on 230/50/1 ph supply. MAKE :- TOASTMASTER / CONTINENTAL

ICE CREAM CABINET ( Chest Type):- Size :60"x30"x34" high approx as per Manufacturers. Ice Cream Cabinet high efficiency refrigeration system with environmentally safe coolant -17º to -24º C, 3/8" dia copper refrigerant coils to operate on AC 230/50/1 supply Repute Makes : CELFROST / WILLIAM / BLUE STAR /VOLTAS /

IMPORTED EQUIPMENTS :- Manufacturing & or Supplying, Placing in position, Commissioning & Testing of Imported Kitchen Equipment in proper & smooth working condition i/c handing over the same to the concerned authorities as follows( Complete as per Manufacturer’s Specifications)

COMBINATION OVEN ( WITHOUT REMOTE) Size :- ( W 900x D830x H1800mm Temp control for all fuctions, steaming hot air and combined heating , fan speed control, auto clean functions, fast cool down function, intrigral maintenance free Greece extraction system, accommodate 6 baking trays , SS, Voltage 400 V or 50 Mhz to 60 Mhz, 10-12 KW three phase, warranty at least 4 years comprehensive on site, auto dosing , system, standard duel stage door opening System, Externally mounted probe, Hybrid steam system ( injection and Boiler) both ability to hold cooking trays at 90% loading position,local service support, Onlie steam technology without use of an internal boiler easily accessible hand shower, Nine step fan speed, ten levels of humidification , no propriety chemicals required for cleaning to reduce recurring cost. MAKE :- RATIONAL/ HAUNO/ ELECTROLUX.

MEAT SLICER:- • Approximate Size 390x470x380mm • Power :- 320 Watt • Blade Dia:- 250mm • Electrical:- 220V/50HZ/1PH. • Weight :- 15.5 Kg. Make:- Celfrost Model 250 ES-10/ Equivalent Model of Sirman Topaz-195/ Equivalent Model of Rewebo.

Meat Mincer:- Size :- As per Manufacturer • Made from diecasted polished aluminum ventilated motor. • Oil Bath Gear Box . • Cast Iron Head & Feeding wall. • S.S plates & knifes. • 24 Volt control & NVR Device. • Net Gross 21 Kg/ 23 Kg. Motor 1 HP/220 V/50Hz Single Phase capacity 35 Kg./Hr. Body made of stainless steel. Feed pan made of S.S removable Motor control by ON/Off indicator switch Mincer end with cylinder of spiral fluted design chrominum plated steel. Heat treated stainless steel knives and plate and feed stromper. Make :- Sirman Model TC-22E/ Equivalent Model of Rewebo.