Chandigarh Administration Tender

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area beyond 3 sq. metres

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): with 6mm thick Toughened glass.

Providing and fixing 6mm thick polycarbonate sheet fixed on existing angle iron frame structure with the help of using self drilling/self tapping screws of size 5.5 x55mm with EPDM seal complete in all respects as and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing bottom aluminium profile with rubber gasket to seal the joint of polycarbonate sheet with self drilling screws etc complete in all respects as and to the entire satisfaction of the Engineer-in-charge.

Providing and fixing Top aluminium profile with rubber gasket to seal the joint of polycarbonate sheet with self drilling screws etc complete in all respects as and to the entire satisfaction of the Engineer-in-charge.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 15 to 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent (Based On DSR No. 11.56)

Providing and placing of SS table counter of overall height 750(H) mm Table Height and 500 mm Seat Height 760mm Depth and 750mm Top Height with seat height of 500mm. supplied in knocked down condition, to be assembled at consignee site. table top plate made in 0.8 mm thick stanless steel. For top SS sheet is cladded on 25mm thick prelaminated partical board with 3mm thick acrylic spacer inserted arround the edges to avoid direct water contact with wooden core in case of spillover. The table Under structure including seat support is made in powder coated mild steel. All Vertical members are made in M.S. Square pipe 40X40X1.2mm thickness and Upper Connecting members and foot rest are made in M.S. Square pipe 25X25X1.2MM thick. Leg material for table and bench MS ERW tubes conforming to IS : 7138. All M.S. Members are epoxy powder coated followed with seven tank process of pre-treatment for anti-rusting and surface activation. Bottom opening covered with PVC shoe/cap.

Body –It is made up of 0.7 CRCA sheet confirming to IS 513: 2008 with powder coated finish up to 50 to 60 Micron. The construction shall be aesthetically appealing completely welded. Pedestal body shall be fitted to the ground with M6 levelers or Nylon caster 40mm Drawer- It is made up of 0.8mm CRCA sheet confirming to IS 513: 2008 with powder coated finish up to 50 to 60 Micron. Fascia made up of 2mm thick CRCA sheet confirming to IS 513: 2008 with powder coated finish up to 50 to 60 Micron Or 18mm thick Prelam (OSL) particle board confirming to IS 12823: 1990 with 2mm thick PVC lipping glued with Kliberit-779.6 glue . PVC flush handle to be mounted on fascia.Box drawers mounted on 27x400mm Telescopic slide with 3/4 extension and File Drawer mounted on 37x400mm Telescopic slide with full extension. Generally 2 types of standard drawer are offered Box drawer in 352x400x70mm and File drawer in 352x400x 245mm. Provision of centralize locking for all the drawers. Generally Hettich make multi drawer lock system is offered. The product must be from a Manufacturer having ISO 9001,ISO 14001,Latest BIFMA 5.1 certificates for few of its products.

Supplying and placing a Medium Back chair with headrest having overall dimensions 900mm to 1000mm Seat Rest Dimensions - 495Wx495D Back Rest Dimensions - 450WX620H Back rest should be made up of mesh having 100% Polyester. frame is made up of dia. 12 mm Bright Bar welded with 8mm thk MS plate. Powder coated in Black color & upholstered with Yuwa mesh. Back rest shoud have adjustable lumbar support. Back rest to be tested with 45 Kg, 120000 cycles @ 10-30 cycles / min Seat should be made of HR Foam fitted on 12 mm ply with fabric upholstery and plastic cover and should have waterfall edge for ergonomic seating. Seatrest should be tested with 55 kg on seat, 120000 cycles @ 10-30 cycles / min Mechanism - Mechanism should be synchro with 1:3 ratio. It should have Synchro 1 point mechanism. It should have upright locking position for backrest. It should be BIFMA Compliant and tested with 109 kg on seat for 3,00,000 Cycles. Armrest - Armrest should be adjustable. Fixed armrest in PP. It should be BIFMA compliant. Armrest should be tested with 41 kg on each arm, 60000 cycles Gaslift - Gaslift should have minimum 100 mm stroke length and should be BIFMA Compliant and tested with 122kg on seat, for 60,000 cycles rotation @ 5-10 rotation / min. Base - Base should be Nylon and should be BIFMA compliant and tested for 1150 kg of load. Castors- Castors should be twin wheel castors having 60 mm dia. It should be BIFMA Compliant and tested with 102 kg on seat for 1,00,000 Cycles. Fabric - 100% Polyester. Fabric should be fire retardant and should have passed Cigarette Bud test. Foam - HR Foam and