Chandigarh Administration Tender

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm( single charge) (As per N.S.)

Providing and laying anti skid ceramic floor tiles of size 300x300mm (thickness to be specified by the manufacturer) of Ist quality conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 mm (As per N.S.)

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (As per DSR 8.31)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm ( single charge) (As per N.S.)

Providing and fixing of kitchen cabinet below working shelves consisting of chowkhats frame of hard wood of 2" x 2"section with one additional member with suitable rebate of 1" x 1/2" on outer side for shutter. The shutters are to be provided with 18mm thick both side pre-laminated particle board with one side decorative, flat pressed 3 layer and graded (medium density), grade I, type II, conforming to IS 12823 (exterior grade) with hard wood lipping of size 19 mm x 6 mm all around and fixed with chowkhat frame with piano hinges and screws etc. and provide with handle and magentic catcher. The complete frame is to be fixed with fastnerst, etc. complete fixed in position to the entire satisfaction of Engineer-in-Charge. (As per N.S.)

Providing and fixing wooden cabinet of 13½” deep and 2’-0" height with open able shutter at wall above 4’-9" height consisting of 18mm thick both side pre-laminated particle board with one side decorative, flat pressed 3 layer and graded (medium density), grade I, type II, conforming to IS 12823 (exterior grade) lipped with hard wood lipping of size 18mm on exposed edges include cost of piano hinges and handle, magnetic cathcer, nail, screws, synthetic adhesive etc. and fixed in position with help of wooden gutties at wall complete in all respect to the entire satisfaction of Engineer-in-charge (As per N.S.)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab over 0.50 sqm (As per DSR 8.2.1.2)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). (As per DSR 5.3)

Centering and shuttering including strutting, propping etc. and removal of form for : Shelves (Cast in situ) (As per DSR 5.9.4)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. (As per DSR 5.22A.6)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade Old work (one or more coats) (As per N.S.)

Painting one or more coats with synthetic enamel paint in all shades on old wood work or metallic or plastered surfaces to give an even shade complete in all respects and to the entire satisfaction of the Engineer in charge. (As per N.S.)

Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface (As per DSR 13.111.1)

Preparation of plastered or concrete surfaces for oil bound distemper or emulsion or apex paint including sand papering the surface or scrapping by patti, applying filling with cement based putty (Birla, Jk or equivalent) to the required finish complete in all respect and to the entire satisfaction of Engineer-in-charge. (As per N.S.)

Extra for making hole for LPG Gas pipe in kitchen work top (baroda green top with RCC slab) with punching machine complete in all respect. Making hole for LPG Gas pipe (As per N.S.)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) (As per DSR 13.1.1)

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick plain PVC door shutters (As per DSR 9.120.1)

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge. (As per DSR 9.119)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (As per DSR 15.56)

Providing and fixing cupboard shutter consisting of 19mm thick commercial board (Archid, Novapan, Kitply, National make) phenol bonded with chowkhat fixed including cost of necessary fitting,( 2 no alum handle ,1 nos hasp and staple and billie ,2 no alum tower bolt screws, nails, fevicol and two coats of special quality paint over one coat of primer after preparation of ply wood surface complete in all respect to the entire satisfaction of Engineer-in-Charge. (As per N.S.)

Providing and fixing of cupboard shelves consisting of 19mm thick commercial board (ISI marked) phenol bonded fixed with hard wood battens and gutties including the cost of necessary lipping screws nails fevicol and two coats of special quality paint over one coat of primer after preparation of surface complete in all respect and to the entire satisfaction of the Engineer in charge. (As per N.S.)

Providing and fixing 35mm thick phenol bounded factory manufactured solid flush door shutter ISI marked with both side commercial face in the existing chowkhat. The rate includes the cost of iron hinges, all necessary Aluminium fittings and painting two coats over one coat of primer after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge. (As per N.S.)

Providing and Fixing 35mm thick golden champ wood (kiln seasoned) wire gauge door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” golden champ wood (kiln seasoned) beading, with two vertical members in each panel to hold wire mesh, with necessary 4 Nos. of hinges 4", 2 Aluminium Tower bolts 8", 2 Aluminium Handles 5” and Aluminium door stopper and single acting door spring and complete fixed in position including two coats of paint and one coat of primer after preparation of surface (special quality) Complete in all respect to the entire satisfaction of Engineer-in-Charge. (As per N.S.)

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineering-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb (As per DSR 10.14.1.1)

Profile E Fixing with adjustable lugs with split end tail to each jamb (As per DSR 10.14.3.1)

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. (As per DSR 15.60)