Chandigarh Administration Tender

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (As per DSR 9.21.1)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works (As per DSR 10.25.2)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate (As per DSR 11.3.1)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm (As per DSR 11.41.2)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm (As per DSR 11.46.2)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick (As per DSR 11.26.1)

12 mm cement plaster: 1:4 (1 cement : 4 fine sand) (As per DSR 13.1.1)

15 mm cement plaster: 1:4 (1 cement : 4 fine sand) (As per DSR 13.2.1)

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. (As per DSR 15.60)

Providing water proofing treatment by laying one coat of cement adhesive Tapecrete mixed with cement in ratio 1:3 (One part of tapecrete : 2 part of cement) complete in all respect and to the entire satisfaction of Engineer-in-charge. (N.S.)

Providing and fixing cup board shutter consisting of 19mm thick commercial board (Archid, Novapan, Kitply, National make) phenol bonded fixed including cost of necessary fitting, screws, nails, fevicol and two coats of special quality paint over one coat of primer after preparation of ply wood surface complete in all respect to the entire satisfaction of Engineer-in-Charge. (N.S.)

P/F 100mm internal dia PVC pipe as rain water pipe on walls of 6 kg. /sqm. pressure with Bend, Elbow and Clamps complete in all respect to the entire satisfaction of Engineer--in-Charge (N.S.)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (As per DSR 15.56)

Dashing Cement Concrete 1:11/2 :3 in R.C.C. beams, Stairs, Facias etc. of average thickness 1" excluding steel reinforcement, centering and shuttering but including curing of the concrete complete in all respect and to entire statisfaction of the Engineer-in-charge. (N.S.)

Chipping of unsound/ weak concrete material from slabs, beams, columns, etc. upto the height of 15 m with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge. (25mm average thickness) (N.S.)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Powder coated aluminium (minimum thickness of powder coating 50 micron) (As per DSR 21.1.1.2)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) (As per DSR 21.1.2.2)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge.Pre-laminated particle board with decorative lamination on both sides (As per DSR 21.2.2)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) (As per DSR 21.3.2)

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16 mm (As per DSR 9.96.1)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :200x10 mm (As per DSR 9.97.3)

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not les s than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper (As per DSR 9.101.1)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm (As per DSR 9.100.1)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 100 mm (As per DSR 9.100.2)