Chandigarh Administration Tender

3 x 1.5 sq. mm

3 x 2.5 sq. mm

3x 4 sq. mm.

3 x 6 sq. mm.

DSR Item No.1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20 mm

25 mm

DSR Item No.1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

DSR Item No.1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

DSR Item No.1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required

5/6 amps switch

3 pin 5/6 A socket outlet

DSR Item No.1.27 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

4 Module (125mmX75mm)

12 Module (200mmX150mm)

DSR Item no. 2.2 Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.

100 A,30KA, FPMCCB

DSR Item no. 2.4 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

8 way (4 + 24), Double door

DSR Item no. 2.10 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Triple pole and neutral

DSR ITEM No.2.16 Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required.

DSR item no. 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

DSR item no. 1.33 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supply, Installation, Testing and Commissioning of 1400 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 7.42, Air delivery minimum 245 CMM, 300 RPM (tolerance as per IS : 374-2019), THD less than 10%, OEM designed electronic regulator unit for speed control in various steps as per BIS (proof shall be submitted alongwith fan before installation at site) and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. The fan should be of Havells/ Atomberg/ Bajaj/ Crompton/ Usha/ Orient make only.

Supply and fixing of 12 modules (200 mm x 150 mm) G.I box suitable for accommodate the following accessories along with modular base and cover plate for modular switches in recess / surface etc as required for Computer Point with 4 Nos. 5/6 Amp. modular switch and 4 Nos. 3 pin 5/6 Amp. modular socket outlet. The job includes the cost of making interconnections with suitable copper wire, painting of box with approved paint and other petty material required to complete the job to the entire satisfaction of Engineer-in-Charge at site.

S/E of 2’x2’ LED fitting in Recess type with integral/ non integral driver to be installed in the existing false ceiling with 4 Nos. steel chain. The fittings should be installed at site with suitable arrangement and the cost includes of 4 nos. MS chain of suitable size and length for support of fittings. The fitting should be Philips/ Wipro/ Bajaj/ Havells/ Surya/ Jaquar/ Crompton/ Triluxmake only. The job includes the cost of cutting of existing false ceiling of suitable size for erection of fitting with suitable arrangement etc. as required at site. The job includes the cost of testing, commissioning and making connection with 3x1.5 sq. mm. copper wire from adjacent light point, other petty material and labour etc. as required to complete the same to the entire satisfaction of Engineer In Charge. The LED fittings should be as per following design criteria as per DNIT Item No.16.

Supply and erection of Copper thimbles of following sizes. The thimble should be of ISI make. The job includes cost of making connection with suitable arrangement required to complete the job to the entire satisfaction of Engineer in charge of the work.

16 mm