Chandigarh Administration Tender

3 x 1.5 sq. mm

3 x 2.5 sq. mm

DSR 1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

25 mm

DSR 1.24 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Telephone socket outlet

DSR 1.55 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

DSR 1.32 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

DSR 1.31 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

DSR 1.27 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

DSR 1.18 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

4 pair

S/E of fresh air fan high speed motor with copper would 10” sweep with louver and plastic body complete with speed motor, blades, epoxy powder coated of Havells make Ventil Air DX HS/ Orient make ventilator/ Crompton make Brisk Air Neo/ Usha Crisp air/ Bajaj Supreme maxima DXI only. The cost includes the connection with adjacent light points and installed on wall with suitable arrangement by providing frame of required size made out 6mm thick water proof plywood to be installed with suitable size rag bolts, nuts after making suitable size hole in the wall if required at site to the entire satisfaction of Engineer-in-charge.

Supply & erection of Cabin/ wall Fan 16” sweep oscillating type complete with blades & regulator. The fan should have 2 Nos. of pull cord switches, one for oscillation and one for speed regulation. The fan should be of Havells make Swing Gyro/ Orient make Industrial heavy duty/ Usha make Turbo HDEF/ Bajaj make Esteem only. The cost includes the connection with adjacent light points and installed on wall with suitable size rag bolts, nuts and other material required to complete the job to the entire satisfaction of Engineer-in-Charge.

Supply, Installation, Testing and Commissioning of 1400 mm sweep (maximum wattage upto 35W), BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 7.42, Air delivery minimum 245 CMM, 300 RPM (tolerance as per IS : 374-2019), THD less than 10%, OEM designed electronic regulator unit for speed control in various steps as per BIS (proof shall be submitted alongwith fan before installation at site) and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. The fan should be of Havells/ Atomberg/ Bajaj/ Crompton make only.

Supply and erection of M.S. box for Computer Point of size 10”x8”x3”deep made out of 16 G.M.S. sheet erected in existing wall and covered with 3mm thick white glazed bakelite sheet with provision for 4 Nos. 5 Amp. Socket with control switch of each socket. The job includes the cost of making interconnections with suitable copper wires painting of box with approved paint and other petty material required to complete the job as per satisfaction of Engineer-in-Charge at site. The switch & socket should be of ISI marked Anchor/ Havells/ Gold Medal make only.

Supply, erection, testing & commissioning of brass antic pictorial LED light of 10-15 watt on existing wall surface with the help of rawl plugs, screws etc. The fitting shall be arranged as approved by the client department. The job includes all labour & petty material required to complete the job to the entire satisfaction of EIC of work. The fitting should be of Philips/ Mayfair/ Bajaj/ Wipro or its equivalent make only.

Supply & Erection of 2’x2’ approx. long recess Type LED Luminaries complete in all respect to be at site with suitable arrangement and the cost includes of 4 nos. MS chain of suitable size and length for support of fittings. The fitting should be Philips/ Wipro/ Bajaj/ Havells/ Surya/ Jaquar/ Crompton/ Trilux make only. The job includes the cost of testing, commissioning and making connection with 3x1.5 sq. mm copper wire from adjacent light point, other petty material and labour etc. as required to complete the same to the entire satisfaction of Engineer in Charge as per DNIT Item No.15.