Chandigarh Administration Tender

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: One or more coats on old work

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Preparation of plastered or concrete surfaces for oil bound distemper or emulsion or apex paint including sand papering the surface or scrapping by patti, applying filling with cement based putty (Birla, Jk or equivalent) to the required finish complete in all respect and to the entire satisfaction of Engineer-in-charge.

Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Providing and fixing 2-0” deep cupboard /cabinet consisting of 19mm thick commercial board and 6mm thick ply on back side, 4mm thick teak ply pasted on the exposed surface and making shelves in cabinet 0.8mm mica inside canbinet . The rate further includes the cost of lipping, piano hinges, cupboard lock, screws, nails, 2 nos. fancy s.s. handles, 2 nos. magnetic catchers, fevicol and painting two coats over one priming coat and preparation of surface on board and ply surface and spirit polishing on teak ply complete in position as per entire satisfaction of Engineer-in-charge.

Providing and fixing wooden cabinet of 13½” deep and 2’ height with openable shutter at wall above 4’-9" height of 19mm thick commercial board (ISI Marked) lipped with teak wood lipping of 19mm x 6mm on exposed edges include cost of nail, screws, Auto hinges, synthetic adhesive etc. The front shutter and sides are to be furnished with 1mm thick ISI marked superior quality mica of approved shade and inner side of the cabinet with 0.8mm thick mica of approved shade fixed in position with help of wooden gutties at wall complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing of kitchen cabinet below working shelves made out with 19mm thick commercial ISI marked ply and front portion of the cabinet furnished with 1mm thick superior quality sun mica of outer side and 0.8mm thick sun mica inner side of the cabinet for fixing the kitchen accessories and jack at bottom synthetic enamel paint over remaining portion. It is also include the cost of sprit polishing on the edge of the lipping cost of stainless steel handle, adhesive, nail, screws etc. complete fixed in position to the entire satisfaction of Engineer-in-Charge.

Providing and fixing heavy duty S.S. kitchen accessories fixing in the existing cabinet with help of best quality telescopic channel. The detail of size as under: Basket of size 21”, 20”, 4”

Basket of size 21”, 20”, 6”

Basket of size 21”, 20”, 8”

Cutlery basket 17”, 20”, 4”

Basket of size 17”, 20”, 4”

Basket of size 17”, 20”, 6”

Basket of size 17”, 20”, 8”

Grain trolley of size 21”, 20”

Vegetable basket 17”, 20”, 6”

Plate basket 17”, 20”, 8”

Cup Saucer basket 17”, 20”, 8”

Hydraulic auto hinges

Corner basket 21” deep

Masala Pull out 6"

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147.The laying of membrane shall be got done through theauthorised applicator of the manufacturer of membrane : 3 mm thick

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of size.Size of Tile 600 x 600 mm

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing and fixing golden champ jaffery on compound wall with frame of golden champ section 2” x 1.3/8” as horizontal member and vertical members fixed with golden champ and strips 4”x 3/8” @ 6” c/c on both faces sides faces of jaffery. The top of jaffery is to be covered with another strip of 2 x 1.3/8”. The complete panel is to fixed over existing wall and M.S. angle with iron nuts and bolts etc. The complete jaffery is to be painted with special quality over one coat of primer complete in all respect to the entire satisfaction of Engineer-in-charge.

Regrading terracing of mud phaska covered with tiles or brick, in cement by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per directions of Engineer-In-Charge.

Providing and fixing 1.5mm thick polycarbonate sheet to be fixed on the existing MS frame with self drilling machine screws complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing 6mm thick polycarbonate multi wall sheet to be fixed on existing M.S. frame with Aluminum rivets complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and Fixing 35mm thick 2nd class teak wood (kiln seasoned) wire gauge door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” teak wood (kiln seasoned) beading, including stainless steel fittings and French spirit polish complete in all respect to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 35mm thick second class teak wood (kiln seasoned) wire gauge window shutters consisting of vertical and horizontal styles 75x35mm size with wire mesh 22 x 12mm gauge fixed with 1/2" x 3/4" teak wood beading. The rate further includes the cost of 3" brass butt hinges brass tower bolts 4", 4"handle 2nos, stay 1no, brass handles 2 nos, screws, nails etc. I-hook, french spirit polishing two or more coats complete in all respect to the entire satisfaction of Engineer-in-charge

Providing and fixing 35mm thick second class teak wood (kiln seasoned) glazed window shutter with vertical style & rails 75mm thick & 4mm thick glass fixed with 1/2” x 3/4” beading and including 2 Nos. of 3” butt hinges stainless steel 4" tower bolts 2nos, stainless steel 4" handles 2nos, and stainless steel eye hook and finished with french spirit polish two coats complete in all respect and to entire satisfaction of Engineer-in-charge.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab over 0.50 sqm

French spirit polishing : One or more coats on old work