Chandigarh Administration Tender

Providing and fixing aluminium sliding door bolts, ISI marked anodised anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

250x16 mm (DSR 9.96.2)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

200x10 mm (DSR 9.97.3)

150x10 mm (DSR 9.97.4)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

125mm (DSR 9.100.1)

Providing and fixing aluminium hanging floor door stopper, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Twin rubber stopper (DSR 9.101.2)

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. DSR: 10.29

Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides (DSR 10.29.1)

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase (DSR 12.21.1)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum moisture resistant board (DSR 12.45.3)

12 mm cement plaster

1:4 (1 cement: 4 coarse sand) (DSR 13.4.1)

Pointing on tile brick work with cement mortar 1:3 (1 cement : 3 fine sand):

Flush/ Ruled/ Struck or weathered pointing (DSR 13.32.1)

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) (DSR 14.5.1)

Renewing glass panes, with wooden fillets wherever necessary:

Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) (DSR 14.6.1)

Regrading terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per direction of Engineer-in-Charge. (DSR 14.13)

Dismantling of Door and windows and clerestory windows ( steel & wood ) shuttter including chowkhats, architrave, hold fasts etc complete & staking within 50m lead.

Area 3 sqm or below (DSR 15.12.1)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. (DSR 15.56)

Disposal of building rubbish /malba/similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. (DSR 15.60)

Chipping of unsound/weak concrete material from slabs, beams, columns etc. up to the height of 15m with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge. 25 mm average thickness. (NS)

Dashing cement concrete with 1:1.5:3 (1cement:1.5 coarse sand :3 graded stone aggregates 10mm nominal size) in RCC beams, walls, columns, slabs, chajjas, facia etc. of average thickness 50mm of upto 10m height including the cost of curing and scaffolding etc. complete in all respect and to the entire satisfaction of engineer in charge.( excluding the cost of centering, shuttering, reinforcement) (NS)

Removing rust from exposed reinforcement bars upto 10m height in RCC walls, columns, beams, shelves etc to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles afer 24hrs of its application with wire brush and thouroughly washing witgh water and allowing it to dry all complete as per directions of engineer in charge. (NS)

Providing and Fixing chicken mesh of size ½"x½" and 26 gauge up to 15m height on RCC beams, facias, brick work etc. wherever required with wooden gutties, nails and screws including drilling holes etc complete as per directions of the Engineer-in-charge. (NS)

Providing and laying water proofing treatment in roof slabs etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (B) Laying of Fibre glass cloth with a coat of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/ sqm when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (C) Third layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. (Based on 22.5) (NS)

Supply of Mineral fibre Tiles beveled tegular edged ceiling tiles 595 x595 mm, 16 mm thick complete in all respect to the satisfaction of Engineer in charge. (NS)

Providing and fixing of PVC pipe (4" dia) 110mm @ 4kg / sqm of approved make including all the accessories i.e. Bend, Tee, reducer etc. and jointing with cement solvent to the entire satisfaction of Engineer-in-charge. (NS)

Cleaning the Concrete surface and removing dirt, dust, bird dropping, grease, oil, algae, fungus, monkey beats, vegetable growth etc., with the help of nano fluids Beechem of karcher RM 269 or easy clean or it's equivalent or other chemical cleaning agent as approved by Engineer-in-charge, of approved brand and manufacturer, with the help of required scrubbers, brushes and also cleaning with high pressure jet cleaner, hot steam or hot water as per site requirement and adding the required amount of chemical as per manufacturer specifications, without causing any scratching/ damage to the concrete surface and finally washing the surface with clean water with the help of pressure jet machine, complete in all respect, including taking all precautions to safeguard ventilators, windows, doors etc. by suitable covering so as to avoid any damage to the building/structure, all as per direction of Engineer-in-charge. The work further includes application of water repallent additives in two coats (The rate is inclusive of all materials, labours & scaffolding). (NS)

Providing and fixing of openable shutters in cupboards of 18-19 mm thick, make Century Sainik /green ply/duro ply board, water proof, termite proof with teak wood liping of size 19 X 4mm on all exposed edges fitted having Nickel hinges superior quality with the help of screws and also having splayed tounged joint if 2no's shutter meet in center including the cost of nails, screws, stops, fevicol and applying two coats of suprior quality paint over one coat of primer on inside & outside of shutter complete in all respect and to the entire satisfaction of enginner in charge. (NS)

Providing and fixing of in position cupboard shelves of 19 mm thick commercial board (ISI marked ) with lipping of soft wood 19mm x10mm on exposed edge supported on brackets of 2 nos hard wood battens 1''x1'' fixed in all with hard wood gutties and screws finished with preparation of ply wood surface and twp coats of special quality paint of approved shade over one coat of primer complete in all respects and to the entire satisfaction of engineer in charge. (NS)

Providing and fixing 35mm thick phenol bounded factory manufactured solid flush door shutter ISI marked with both side commercial face in the existing chowkhat. The rate includes the cost of aluminium hinges 4'', SS handles 5'', Aluminium Tower bolts 8'' & 6''all necessary Alumn fitting and painting two coats over one coat of primer after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge. (NS)

Providing and fixing 35mm thick golden champ wood (kiln seasoned) glazed window shutters consisting of vertical and horizontal styles 75x35mm size with 4mm thick floated glass pane fixed with 1/2"x3/4" golden champ wood (kiln seasoned) beading. The rate further includes the cost of 2 nos. 3" butt hinges, 2nos Aluminium tower bolts 4", Aluminium handles 1 no. I-hook and two coats of special quality enamel paint over coat of primer after preparation of surface (special quality) and removal of old shutter complete in all respect to the entire satisfaction of Engineer-in-charge. (NS)

Providing and fixing 35mm thick golden champ wood (kiln seasoned) wire gauge window shutter with vertical style & rails 75mm thick and 22 x 12 gauge wire mesh fixed with 1/2” x 3/4” beading and including 2 Nos. of 3” iron hinges , 2 nos tower bolts 4'' And 1 no Aluminium handle 4'' and complete fixed in position including two coats of paint and one coat of primer after preparation of surface (special quality) Complete in all respect to the entire satisfaction of Engineer-in-Charge. (NS)

Providing and Fixing 35mm thick golden champ wood (kiln seasoned) wire gauge door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” golden champ wood (kiln seasoned) beading, with two vertical members in each panel to hold wire mesh, with necessary 4 Nos. of hinges, Aluminium Tower bolts, Aluminium Handles 5” and Aluminium. door stopper and door closer and complete fixed in position including two coats of paint and one coat of primer after preparation of surface (special quality) Complete in all respect to the entire satisfaction of Engineer-in-Charge. (NS)

Providing and laying water proofing coating having three coats of rain jackets @ 15sqft/Kg over a priming coat of water proofing paint @ 10 sft/ Kg including fiber mesh of size 800 microns with total thickness of 900 to 1000 microns forming high elstic and resilient coating with resistant to UV rays and non toxic in nature with life of minimum 10 years complete in all respect and entire satisfaction of Engineer-In-Charge. (NS)

Providing and fixing Golden Champ wood Chowkhats (Kiln seasoned ) including cost of corner straps, iron hold fasts, screws, nails fevicol etc. The rate includes the cost of dismanteling of the damages chowkhats and making good the damage to the walls plaster and floors as required including disposal of rubbish to the dumping ground. The rate further includes the cost of special quality paint over one coat of primer etc complete in all respect and to the entire satisfaction of Engineer-in-charge. (NS)

Credit

old bricks @ Rs. 5.5/ each

old brick tiles @ 7.50/each

Brick /Brick bats @ Rs. 650 / cum

mud phaska @ Rs. 150 / cum

Recovery of old dismantled fuel wood @ Rs. 12.0 / kg

Note: No extra Rates for cleaning, stacking, carriage on any dismantled material i.e. Brick, Brick tiles, Brick/Tiles bats etc. will be given