Tourism Department Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 43,38,765Document Cost
₹ 3,000Tender Fee
Refer Documents
Summary
Construction Of Jongal Balahu Khetra At Jongal Balahu Archaeological Site
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_DOT_40457_1Tender No
ATDC/CS/670/2024/2673 dt. 14.11.2024Tender Authority
Tourism Department ViewPurchaser Address
-Website
http://http://tourism.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)
809.41
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concretework, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level
5234
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concretework, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). All works above plinth level upto floor V level
3135.16
-
-
Centering and shuttering including strutting, propping etc. and removal of form for all heights :Foundations, footings, bases of columns, etc. for mass concrete
1453.46
-
-
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
16809.6
-
-
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick
3738.85
-
-
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Columns, Pillars, Piers, Abutments, Posts and Struts
4605.1
-
-
Centering and shuttering including strutting, propping etc. and removal
of form for all heights : Suspended floors, roofs, landings, balconies and access platform
828.62
-
-
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Stairs, (excluding landings) except spiral-staircases
11.83
-
-
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)
1335.34
-
-
Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with sand, with common burnt clay non modular bricks.
7479.07
-
-
Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)
414
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V levelCement mortar 1:3 (1 cement :3 coarse sand)
5114.46
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)
5.63
-
-
Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement Concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like.Cement mortar 1:6 (1 cement : 6 coarse sand)
1440.07
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto all level.Thermo-Mechanically Treated bars of grade Fe-500D
217149.49
-
-
12 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)
7242.11
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)
9762.22
-
-
6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)
502.47
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to
prepare the surface even and smooth complete.
928.25
-
-
Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
6268.97
-
-
New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
692.77
-
-
With ready mixed red oxide zinc chromate primer ofapproved brand and manufacture on steel galvanised iron/steel works
793.89
-
-
Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture
744.6
-
-
25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class teak wood
20
-
-
52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.
563.12
-
-
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour Two coats
143
-
-
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre
143
-
-
Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
6.53
-
-
Painting wood work with Deluxe Multi Surface Paint of required shade. Two ormore coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture
4.51
-
-
Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used.With G.I. barbed wire
17413.79
-
-
Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.
14952.05
-
-
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
14635.33
-
-
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and
applying a priming coat of approved steel primer all complete.
3360.46
-
-
Providing, driving with hydraulic piling rigs with power units and installing driven cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of shoe and the length of pile to be embedded in the pile cap etc. all complete. (Length of pile for payment shall be measured from top of shoe to the bottom of pile :400 mm dia piles
6668
-
-
Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing.Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge.Single pile upto 50 tonne Safe capacity Initial test (Test Load 2.5 times the Safe capacity)
3
-
-
Providing and fixing of cultural art work for Dekachang as per direction of Engineer-in-charge.
1
-
-
Providing and fixing of cultural art work for Borghar as per direction of Engineer-in-charge.
1
-
-
Providing and fixing of cultural art work for Tongi ghar as per direction of Engineer-in-charge.
3
-
-
Providing wood work in frames of doors, windows, clerestory windows and otherframes, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).(a) With sal wood
0.17
-
-
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard woodand well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
2.26
-
-
Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Kiln seasoned and chemically treated hollock wood 30 mm thick
3.6
-
-
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
150
-
-
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
22.5
-
-
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.M.S. tube
2488.14
-
-
Providing, fitting and fixing of Children Play Equipments of the following categories as per direction of Engineer in Charge :Single Slides small (Size: L-9 x W-2.3 x H-6ft)
3
-
-
Single Slides Medium (Size: L-12 x W-2.3 x H-8ft)
1
-
-
Single Slides Big (Size: L-14 x W-2.3 x H-10ft)
2
-
-
Curve Crawling Tube (Size: L-10.11 x W-4.3 x H-5.10ft)
1
-
-
Ring Climbers (Size: L-8 x W-2.7 x H-6.5ft)
1
-
-
Straight Climbers (Size: L-6 x H-6ft)
1
-
-
Tiger Rocker (Size: L-2.16 x W-0.83 x H-2.66ft)
2
-
-
Horse Rocker (Size: L-2.66 x W-2 x H-2.66ft)
2
-
-
Whale Rocker (Size: L-3.11 x W-1.53 x H-2.73ft)
2
-
-
Double Swing (Size: L-8 x W-4 x H-7.5ft)
2
-
-
Circle Swing (Size: L-7 x W-5.5 x H-7ft)
1
-
-
Triple Swing (Size: L-11 x W-5 x H-7.5ft)
1
-
-
Horse See-Saw (Size: L-6.66 x W-1.66 x H-2.33ft)
1
-
-
4 Seater See-Saw (Size: L-8 x W-8 x H-2.2ft)
2
-
-
Joining Spiral Slides (Size: L-14 x W-4.5 x H-5ft)
1
-
-
Horse Merry Go Round (Size: L-5Ft Dia)
1
-
-
Horse Merry Go Round (Size: L-5Ft Dia)
1
-
-
2 Seater See-Saw (Size: L-8 x W-1.7 x H-2.2ft)
1
-
-
2 Seater Junior See-Saw (Size: L-7 x W-1.33 x H-1.6ft)
2
-
-
Triple Slide (Size: L-25 x W-7 x H-10ft)
1
-
-
Park Bench (Size: L-4 x W-1.4 x H-3.3ft)
15
-
-
Walking Barrel (Size: L-8Ft x H-3ft)
1
-
-
Multiplay Station (Size: L-29.1 x W-16.7 x H-12.13ft)
1
-
-
Multiplay Station (Size: L-27.5 x W-21.9 x H-9.88ft)
1
-
-
Installation & Transportation Charges
1
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B
70
-
-
Supping and drawing following size of FRLS PVC insulated copper conductor, single core cable in the existing suface recessed steel/ PVC conduit as requrired: 3C X 1.5 sqm
150.02
-
-
Supping and drawing following size of FRLS PVC insulated copper conductor, single core cable in the existing suface recessed steel/ PVC conduit as requrired: 3C X 4 sqm
45
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switch
17
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 A socket outlet
6
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10kA, "C" curve, miniature circuit breaker suitable for inductive load of follwing poles in the existing MCB DB complete with connections, testing and commissioning etc. as required :single pole
2
-
-
Supplying and fixing following rating, four pole, 415, isolator in the existing MCB DB complete with connections, testing and commissioning as required
40A
2
-
-
Supplying and fixing cable End Box ( Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts on surface / recess, complete with testing and commissioning etc, as required.
For 6 way, Double Door SPN MCBDB
4
-
-
Supplying and fixing cable End Box ( Loose Wire Box) suitable for follwing triple pole and neutral, sheet steel, MCB distribution board, 415 Volts on surface / recess, complete with testing and commissioning etc. as required.For 4 way, Double Door SPN MCBDB
1
-
-
Sypply installation testing commissioning Surface mounted Batten light 22W LED of Phillips make cat no BN021C LED20S PSU CW GR S2or equivalent make including connection complete.
4
-
-
Supplying including fitting fixing of Energy saving ( 5 Star)1200mm sweep A.C. Ceiling fan (Havells make) model 'ES Neo' or equivalent ,complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator].
2
-
-
Supply , installation testing commisioning of 100W Solar land scape LED Street light of Havells make with model name 'Alpha' or equivalent make with programmed dimming option including PCC base foundation and 6mtr pole complete with connection as required.
8
-
-
Supply , installation testing commisioning of 120W LED Flood light of Havells make with model name "JETA IRIS '' or equivalent make with including PCC base foundation complete with connection as required.
3
-
-
Providing fitting fixing and installation of Tiwa Jadughar Exhibit Items and art display as per Engineer -in-charge.
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%