Tourism Department Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 1,98,014Document Cost
₹ 3,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_DOT_37801_1Bid Award Id
ViewTender No
ATDC/CS/654/2024/792 dtd. 26.06.2024Tender Authority
Tourism Department ViewPurchaser Address
-Website
http://http://tourism.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
-
-
-
All kinds of soil.
223.7
-
-
FILLING IN PLINTH
-
-
-
Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.
189.28
-
-
P.C.C. WORKS
-
-
-
1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources)
8.23
-
-
1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)
22.59
-
-
SOLING
-
-
-
Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud morter , including filling joints with jamuna sand , with common burnt clay non modular bricks.
374.88
-
-
REINFORECED CEMENT CONCRETE WORKS
-
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
-
-
-
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
58.73
-
-
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :
-
-
-
1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu-
ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
20.3
-
-
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
107.59
-
-
SHUTTERING
-
-
-
Centering and shuttering including strutting, propping etc. and removal of form for
-
-
-
Foundations, footings, bases of columns, etc. for mass
55.16
-
-
Suspended floors, roofs, landings, balconies and access platform
440.9
-
-
Lintels, beams, plinth beams, girders, bressumers and cantilevers
442.58
-
-
Columns, Pillars, Piers, Abutments, Posts and Struts
199
-
-
MASONARY WORK
-
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class
-
-
-
Cement mortar 1:4 (1 cement : 4 coarse sand)
12.98
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :
-
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
-
-
-
Cement mortar 1:3 (1 cement : 3 coarse sand)
601.85
-
-
VITRIFIED TILES
-
-
-
Providing and laying vitrified floor tiles in differnnt sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make , in all colour and shades, laid on 20 mm thick cement morter 1:4(1 cement : 4 course sand ), joining with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement and matching pigments etc., complete
-
-
-
Size of tiles 600x600
271.65
-
-
WALL TILES
-
-
-
Providing and laying vitrified floor tiles in differnnt sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to IS : 15622, of approved make , in all colour and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive ( water based) conforming to IS: 15477, in averge 6mm thickness , including grouting of joints ( Payment for grouting of joints to be made separtely)
-
-
-
Size of tiles 500x500
108.8
-
-
MARBLE FLOORING
-
-
-
Crazy marble stone flooring, including filling the gaps with light shade pigment with white cement marble powder mixture (3 parts of white cement : 1 part of marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 white, black or white and black marble chips of sizes from 1 mm to 4 mm nominal size by volume), with under
layer 25 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate 12.5 mm nominal size), including rubbing, polishing and cement slurry etc. complete :
-
-
-
18 mm thick crazy marble stone white, black or as specified
37.74
-
-
CEMENT PLASTERING
-
-
-
15 mm cement plaster on rough side of single or half brick wall of mix:
-
-
-
1:4 (1 cement: 4 coarse sand)
548.2
-
-
WOOD WORKS
-
-
-
CHOWKATHS
-
-
-
Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S. hold fast (40mmx3mmx250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified.
-
-
-
(a) With sal wood
0.51
-
-
PANELLED DOOR
-
-
-
Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerstory window, fixing with but hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer -in-charge. ( Note:- Butt hinges and necessary screws shall be paid separately)
-
-
-
Second class teak wood
-
-
-
35 mm thick shutters
12.6
-
-
WINDOWS & VENTILATORS
-
-
-
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make
conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/
neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including
cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
-
-
-
For fixed portion
-
-
-
Powder coated aluminium (minimum thickness of powder coating 50 micron)
97.46
-
-
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)
182.6
-
-
PAINTING
-
-
-
PLASTER OF PARIS & WALL PUTTY
-
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
548.2
-
-
Applying one coat of water thinnable cement primer of approver brand and manufacture on wall surface
-
-
-
Water thinnable cement primer
548.2
-
-
Finishing walls with water proofing cement paint of required shade :
-
-
-
New work (Two or more coats applied @ 3.84 kg/10 sqm)
164.46
-
-
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :
-
-
-
Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm
383.74
-
-
POLISHING IN WOOD WORK
-
-
-
Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 lit / 10 sqm over an under coat of primer applied @ 0.75 lit / 10 sqm of approved brande and manufacture.
17.01
-
-
PRIMER IN WOOD
-
-
-
With ready mixed pink or grey primer of approved brand and manufacture on wood work ( hard and soft wood)
17.01
-
-
REINFORCEMENT
-
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
-
-
-
Thermo-Mechanically Treated bars of grade Fe-500D or more.
7504.34
-
-
Steel reinforcement for R.C.C. work including strsightening , cutting, bending, placing in position and binding all complete above plinth level
-
-
-
Thermo - Mechanically Treated bars of grade FE - 500D or more
11993.03
-
-
CIVIL WORKS (SEPTIC TANK)
-
-
-
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
-
-
-
All kinds of soil.
23.25
-
-
Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km, also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc., complete.
10.32
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
-
-
-
1:2:4 (1 Cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources).
0.85
-
-
1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources).
0.92
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
-
-
-
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
0.02
-
-
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :
-
-
-
1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources)
0.46
-
-
Centering and shuttering including strutting, propping etc. and removal of form for :
-
-
-
Foundations, footings, bases of columns, etc. for mass concrete
1.74
-
-
Suspended floors, roofs, landings, balconies and access platform
4.39
-
-
Lintels, beams, plinth beams, girders, bressumers and cantilevers
0.53
-
-
Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks:
-
-
-
1:4 (1 cement : 4 coarse sand)
11.07
-
-
Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:
-
-
-
Cement mortar 1:4 (1 cement : 4 coarse sand)
4.77
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
-
-
-
Cement mortar 1:3 (1 cement :3 coarse sand)
2.32
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix :
-
-
-
1:4 (1 cement: 4 fine sand)
23.11
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
-
-
-
Thermo-Mechanically Treated bars of grade Fe-500D or more.
42.43
-
-
SANITARY WORKS
-
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
4000
-
-
Providing and fixing PTMT pillar cock of approved quality and colour.
-
-
-
15 mm nominal bore, 107 mm long, weighing not less than 110 gms
10
-
-
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :
-
-
-
W.C. pan with ISI marked white solid plastic seat and lid
6
-
-
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :
-
-
-
Rectangular shape 453x357 mm
8
-
-
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :
-
-
-
One urinal basin with 5 litre white P.V.C. automatic flushing cistern
3
-
-
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
-
-
-
White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
8
-
-
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.
-
-
-
Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms.
9
-
-
Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
7
-
-
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.
-
-
-
600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.
6
-
-
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
6
-
-
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.
6
-
-
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
-
-
-
Flexible pipe
-
-
-
32 mm dia
7
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work
-
-
-
32 mm nominal outer dia. Pipes.
65
-
-
40 mm nominal outer dia. Pipes.
81
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc.
-
-
-
20 mm nominal outer dia. Pipes
50
-
-
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.
-
-
-
15 mm nominal bore.
7
-
-
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.
-
-
-
15 mm nominal bore
6
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
-
-
-
40 mm nominal bore
4
-
-
Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed.
-
-
-
Jaquar make
-
-
-
(b) Long neck with areator
14
-
-
ELECTRICAL WORKS
-
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.
-
-
-
Group A
40
-
-
Group B
35
-
-
Group C
40
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
-
-
-
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
750
-
-
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
634
-
-
2 X 4 sq. mm + 1 X 4 sq. mm earth wire
355.99
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
-
-
-
5/6 A switch
30
-
-
15/16 A switch
20
-
-
3 pin 5/6 A socket outlet
15
-
-
Supplying and fitting fixing of Electric storage water heater [Geyser] of Bajaj/Crompton/Racold/V. Guard or equivalent make including necessary connection cable, as approved by the Deptt.)etc. as required complete and as directed by the Department.
-
-
-
25.00 litres. Capacity (5 Star Model) (Crompton/Racold/V.Guard or equivalent make)
2
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.
-
-
-
1 or 2 Module (75mmX75mm)
5
-
-
3 Module (100mmX75mm)
10
-
-
4 Module (125mmX75mm)
5
-
-
Supplying and fixing following way, single pole and neutral,sheet steel, MCB distribution board, 240 V.
-
-
-
6 way , Double door
4
-
-
Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.
-
-
-
40 A
3
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
-
-
-
Single pole
25
-
-
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories.
1
-
-
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
15
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
-
-
-
Upto 35 sq. mm
100
-
-
Supplying with installation testing and commissioning of Hi -- wall 3 STAR rating non ducted split type air conditioner of the following capacity with cordless remote complete with indoor and outdoor unit, copper pipe and electrical connection up to 5 m between the room unit and out door unit as approved by the Deptt.) and as directed by the department.
-
-
-
Daikin FT - M Series model COIL UNIT FT60MV16 & CONDENSEING UNIT R60MV16
6
-
-
Supplying with fitting and fixing Voltage stabilizer of the following specification complete including making necessary connection as approved, specified and directed by the deptt. (SKYLAND / Vee-Dee / V GUARD / VERTEX/ INDO/ VENUS make)
-
-
-
250 VA Auto Cut Input 90-280 V Out put 200-240 V
6
-
-
Supplying fitting, fixing, testing and commissioning of following capacity motor (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) complete with necessary connection as approved, specified and directed by the Department
-
-
-
1 HP single phase 1420 rpm
1
-
-
Supplying with fitting fixing of CFL/Fluorescent luminaries complete with all accessories such as ballast, starter etc. directly on wall / ceiling including connection as approved by the Deptt.)with 1.5 sq mm P.V.C. insulated S.C. copper conductor as required and as directed by the department.
-
-
-
Striplite luminaries complete with VPIT copper ballast/ Electronic ballast and decorative end cap and 1 X 36 / 40 watt Fluorescent tube.(Crompton Greaves make) Model- DSG1114LDB CROMGOLD / DSG1114LDBN CROM GOLD NEW/ DSG1214EB ENERGYGOLD/ DSG1314EB CG GOLD/ DSG 1414EB PLANET GOLD with Power Lux Lamp/ Super Saver / Super Brite Lamp or equivalent (Equivalent will be selected by the deptt considering the mother items rate) PHILIPS/ WIPRO/ BAJAJ/ Havells/ HPL/ SOLAR/ JAQUAR make.
15
-
-
Supplying and fixing of Jaquar or equivalent Philips/ Wipro LED spot light fittings complete with Shade, back plate including connection cable, as approved by the Deptt.s etc. as required.
-
-
-
LED Square front spot light,3W
8
-
-
Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including providing and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch ( Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.),GI/ MS switch board (I.S.I. marked) with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete.
-
-
-
Long point up to 10.00 metre. Length.
2
-
-
BOREWELL
-
-
-
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air
compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
48
-
-
Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in-Charge.
-
-
-
9 PN - 10 Pipe, 110 mm OD (SDR-11)
50
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all
CPVC plain & brass threaded fittings, including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings
with one step CPVC solvent cement and testing of joints complete
as per direction of Engineer in Charge.
-
-
-
32 mm nominal dia Pipes
60
-
-
40mm nominal dia Pipes
70
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
4
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all
CPVC plain & brass threaded fittings, including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of
-
-
-
40 mm nominal dia Pipes
100
-
-
25 mm nominal dia Pipes
127
-
-
Ground floor toilet
-
-
-
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
-
-
-
All kinds of soil.
10.13
-
-
FILLING
-
-
-
Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.
9.31
-
-
P.C.C. WORKS
-
-
-
1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)
6.75
-
-
Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud morter , including filling joints with jamuna sand , with common burnt clay non modular bricks.
6.75
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
-
-
-
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
1.96
-
-
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :
-
-
-
1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu-
ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
4.6
-
-
Centering and shuttering including strutting, propping etc. and removal of form for
-
-
-
Foundations, footings, bases of columns, etc. for mass
3.6
-
-
Suspended floors, roofs, landings, balconies and access platform
19.95
-
-
Lintels, beams, plinth beams, girders, bressumers and cantilevers
53.84
-
-
Columns, Pillars, Piers, Abutments, Posts and Struts
8.85
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class
-
-
-
Cement mortar 1:4 (1 cement : 4 coarse sand)
1.63
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
-
-
-
Cement mortar 1:3 (1 cement : 3 coarse sand)
39.02
-
-
15 mm cement plaster on rough side of single or half brick wall of mix:
-
-
-
1:4 (1 cement: 4 coarse sand)
81.38
-
-
Applying one coat of water thinnable cement primer of approver brand and manufacture on wall surface
-
-
-
Water thinnable cement primer
81.38
-
-
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
-
-
-
40 mm thick with 20 mm nominal size stone aggregate
29.3
-
-
Providing and laying vitrified floor tiles in differnnt sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to IS : 15622, of approved make , in all colour and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive ( water based) conforming to IS: 15477, in averge 6mm thickness , including grouting of joints ( Payment for grouting of joints to be made separtely)
-
-
-
Size of tiles 600x600
29.3
-
-
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
59.22
-
-
Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance
±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door
frame to be Jointed with galvanized brackets and stainless steel screws,
joints mitred and Plastic welded. The hinge side vertical of the frames
reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1
mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame
complete as per manufacturer’s specification and direction of Engineerin-
charge
9.9
-
-
23x10 mm are provided on both vertical edges to ensure the
overall thickness of 25 mm. M.S. tube having dimensions 19
mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the
hinge side of the door. Core of the door shutter should be filled
with High Density Polyurethane foam. The Top & Bottom edges
of the shutter are covered with an end-cap of the size 25 mm
X 11 mm. Door shutter shall be reinforced with special
polymeric reinforcements as per manufacturer’s specification
and direction of Engineer-in-charge to take up necessary
hardware and fixtures. Stickers indicating the locations of
hardware will be pasted at appropriate places25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X
25 mm or less as per requirement with an average wall
thickness of 1 mm (± 0.3 mm). PVC foam end cap of size
3.15
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
-
-
-
Thermo-Mechanically Treated bars of grade Fe-500D or more.
746.3
-
-
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.
-
-
-
35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
3.15
-
-
PARKING AREA
-
-
-
Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil
180
-
-
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge.
126
-
-
Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km, also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc., complete.
36
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.2A 1:1.5:3 (1 Cement: 1.5 coarse sand (zone-III) including manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 25% : 3 graded stone aggregate 20 mm nominal
size Recycled Concrete Aggregate (RCA) upto 25%).
6.92
-
-
Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: 6.2.1 Cement mortar 1:4 (1 cement : 4 coarse sand)
7.8
-
-
Brick work with common burnt clay modular bricks of class designation, 7.5 in foundation and plinth in: Cement Mortar 1:6 (1 cement : 6 coarse sand).
3.48
-
-
Centering and shuttering including strutting, propping etc. and removal Foundations, footings, bases of columns, etc. for mass
concrete
48.64
-
-
Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction , of approved size , design & shape , laid in required......etc. all complete as per the direction of Engineers - in - charge
180
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix : 13.2.1 1:4 (1 cement: 4 fine sand)
20.52
-
-
Pump House
-
-
-
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
-
-
-
All kinds of soil.
13.5
-
-
FILLING
-
-
-
Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.
12.22
-
-
P.C.C. WORKS
-
-
-
1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)
0.9
-
-
Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud morter , including filling joints with jamuna sand , with common burnt clay non modular bricks.
9
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
-
-
-
1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
3.97
-
-
Centering and shuttering including strutting, propping etc. and removal of form for
-
-
-
Foundations, footings, bases of columns, etc. for mass
6
-
-
Suspended floors, roofs, landings, balconies and access platform
7.54
-
-
Lintels, beams, plinth beams, girders, bressumers and cantilevers
8.98
-
-
Columns, Pillars, Piers, Abutments, Posts and Struts
6
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class
-
-
-
Cement mortar 1:4 (1 cement : 4 coarse sand)
1.35
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
-
-
-
Cement mortar 1:3 (1 cement : 3 coarse sand)
20.8
-
-
15 mm cement plaster on rough side of single or half brick wall of mix:
-
-
-
1:4 (1 cement: 4 coarse sand)
41.6
-
-
Applying one coat of water thinnable cement primer of approver brand and manufacture on wall surface
-
-
-
Water thinnable cement primer
41.6
-
-
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
-
-
-
40 mm thick with 20 mm nominal size stone aggregate
8.97
-
-
Providing and laying vitrified floor tiles in differnnt sizes ( thickness to be specified by the manufacturer ) with water absorption less than 0.08% and conforming to IS : 15622, of approved make , in all colour and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive ( water based) conforming to IS: 15477, in averge 6mm thickness , including grouting of joints ( Payment for grouting of joints to be made separtely)
-
-
-
Size of tiles 600x600
8.97
-
-
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
37.67
-
-
Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance
±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door
frame to be Jointed with galvanized brackets and stainless steel screws,
joints mitred and Plastic welded. The hinge side vertical of the frames
reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1
mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame
complete as per manufacturer’s specification and direction of Engineerin-
charge
5.2
-
-
25 mm or less as per requirement with an average wall
thickness of 1 mm (± 0.3 mm). PVC foam end cap of size
23x10 mm are provided on both vertical edges to ensure the
overall thickness of 25 mm. M.S. tube having dimensions 19
mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the
hinge side of the door. Core of the door shutter should be filled
with High Density Polyurethane foam. The Top & Bottom edges
of the shutter are covered with an end-cap of the size 25 mm
X 11 mm. Door shutter shall be reinforced with special
polymeric reinforcements as per manufacturer’s specification
and direction of Engineer-in-charge to take up necessary
hardware and fixtures. Stickers indicating the locations of
hardware will be pasted at appropriate places25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm X
2.1
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
-
-
-
Thermo-Mechanically Treated bars of grade Fe-500D or more.
375.96
-
-
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.
-
-
-
35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
1.58
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements