Skill Employment And Entrepreneurship Department Tender

22.23A Providing and applying polymer modified, flexible cementatious negativeside waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg/10sqm. One coat of self priming of cementatious waterproofing polymer (dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge

17.2 Providing and fixing white vitreous china pedestal type water closet( European type W.C pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device(handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting making good the walls and floors wherever required:

17.7 Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15mm C.P. brass pillar tap

17.8 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

17.73 Providing and fixing PTMP towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangment of approved quality and colour. 17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.

18.65 Providing and fixing PTMT SOAP Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fiting arrangements, weighing not less thann 106gms

17.32 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing (17.32.4 Rectangular Shape)

18.54 Providing and fixing PTMT bib cock of approved quality and colour.

18.55 Providing and fixing PTMP stop cock of approved quality and colour. 18.55.2.20 mm nominal bore, 89 mm long, weighing not less than 88 gms

17.38 Providing and fixing bend of required degree with actress door, insertion rubber washer 3 mm thick, bolts and nuts complete. 17.38.2 75 mm dia 17.38.2.1 Sand cast iron S&S as per IS

18.92 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M- profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. For 15.88 mm outer dia pipe Equal Tee

9.20 Providing and fixing ISI marked flush door shutters conforming to IS:2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 9.20.2. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Ana 1 Providing and fixing at all height wall panelling (2m x 2m) with 19 mm thick Plywood including providing and fixing to framework made of 50 mm x 50mm Plywood complete with necessary laminate, nails, adhesive etc as per direction of Engineer-in Charge.

Ana 2 Supplying, fitting and fixing UPVC PIPE(4 Kg/cm2) pipes, 110 mm dia approved including joining, fitting and fixing etc. in exposed surface or in trenches, as necessary complete at all levels including beloww G.L as directed and specified.

Ana 3 Supplying, fitting and fixing UPVC PIPE(4 Kg/cm2) pipes, 75 mm dia approved including joining, fitting and fixing etc. in exposed surface or in trenches, as necessary complete at all levels including beloww G.L as directed and specified.

Ana 4 Supplying, fitting and fixing UPVC PIPE(4 Kg/cm2) pipes, 110 mm dia approved including joining, fitting and fixing etc. cocealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages, as necessary complete at all levels including below G.L as directed and specified

Wiring for light/fan/call bell point with 3x1.5 sq mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 withy flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel/Nicco/Anchor or Equivalent Make as approved by the Deptt.) with flat 19mm ISI marked casing 'n' capping (AKG/Precision/Presto plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/bell push(Anchor penta/Gold medal/Kolor kany.Kom/Havells or equivalent make as approved by theDeptt.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover, ceiling rose etc. complete as directed and specified by the Deptt. : Medium point up to 6.00 metre. Length

Long point up to 10.00 metre. Length

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic coppe4r conductor for voltage grade up to 1100 volt ( Finolex/RR Kabel/Nicco/Anchor or Equivalent Make as approved by the Deptt.) in surface with flat ISI marked casing 'n' capping (AKG/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) system including earth continuity. : With 3 x 2.5 sq mm. + earth continuity with 2 x 1.5 sq. mm. cable in flat 19mm ISI marked casing 'n' capping system

Wiring to 5 a pin 6 Amps plug point with 1.5 sq. mm P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper for voltage grade up to 1100 volts ( Finolex/RR Kabel/Nicco/Anchor or Equivalent Make as approved by the Deptt.) with flat 19mm ISImarked casing 'n' capping (AKG/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface system, including 5 pin 6 Amps flush type plug socket and 6 Amps F/T switch (Anchor penta/Gold medal/Kolor kany.Kom/Havells or equivalent make as approved by theDeptt.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete, when placed elsewhere. : Medium point up to 6.00 metre. Length

Supplying with fitting and fixing single Pole 10 KA 240/415V 50 Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. : C Series ( Schneider MG, legrand, Hager Make) 6 to 32A

Supplying with fitting and fixing TPN 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the Deptt. : C Series ( Schneider MG, legrand, Hager Make) 63A

Supplying with fitting and fixing sheet steel, phosphatised, powder painted Single door surface mounting TPN MCB DB incorporated with bas-bar, Neutral Link, Earth bar and bin rail etc fitted on wall with grouting nuts & bolts are reqd. complete with makling necessary connection as approved, specified and directed by the deptt. : ABB, Schneider MG, Legrand, Hager Make 4 way TPN (4 + 12) Single Door

Supply and laying of following size Solid Aluminium conductor up to 10 sq mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Armour ( Aliminium for single core up to 70 sq mm balance Aluminium strip, Galvanised for cables up to 2 x 10 sq mm 3 x 10 sq mm, 4 x 6 sq mm balance all galvanised steel strip), extruded PVC Type ST2 Sheathed, 650/1100V grade as per IS 7908 (Part 1) 1988, LT armoured U.G. cable laid in pucca flooring, road crossing, drain crossing as per site requirement and partially in air to connection as approved by the Depts. the control switch, through medium duty G.I. pipe ( Tata/Nezone make oe equivalent as approved by the Deptt) bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the deptt. (Nicco/Havells/RPG/CCI/Polycab/Gloster/Finolex make): Core - 4 A2XWY A2XFY 35.00 Sq. mm 4 Core U.G. cable in 50mm dia medium duty hot dip galvanised pipe (AKG or equivalent as approved by the Deptt.)

Supplying and fixing of bulk head fitting suitable for CFL lamp complete with all accessories including 20 watts CFL lamp and connection as approved by the Deptt.) as required.

Supply, installation & testing of G.I. earth station with perforated 40 mm dia and 4.50 metre long heady duty G.I. pipe with necessary 40 mm dia. G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx 40 mm G.I. reducing socket for funnekl including locking arrangement 300 mm x 300 mm x 6 mm hinged cover C.I. earth plate complete with diggingof earth pit, construction of brick chamber and plastering of both inner & outer surface of wallas specified and directed by the deptt.

Extra for using salt (5 K and Charcoal (64 K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the Deptt.

Supplying & laying of 25 X 4 mm size Copper strips drawn on surface from earth electrode to Electrical switch gears, machineries etc complete with supply of Brass nuts & bolts, screws etc including riveting, soldering & making connection as approved, specified and directed by the deptt.

Supplying fitting and fixing of LED batten tubes high quality alluminium extruded withy decorative end caps connection with 1.5 mm2 1core PVC insulated round copper conductor as required and as directed by the department. : d. LGL 1X020 X C/LGLZo1X020XCN//LGLZO X 020 XCW(20W)

Supplying , installation, testing and Commission of the following indoor Decorative Recess mounted LED down lighter luminaries of model no-LESPO1R009XC/ LESPO1R009XN/ LESP01R009XW/ L00957R00/ L00940R000/L00930R000/LD90-111-XXX-65-XX complete with all accessories such as ballest, starter, etc. In the false ceiling type Armstrong/ Gypsum or similar ceiling mounting with necessary support with 1.5 sq. mm. P.V.C. insulated S.C. copper conductor as required and as directed by the department (Jaquar/LT/ Wipro make).

Licensing Board Expendituire

Supplying installation, testing and commissioning of Passenger Elevator (Kone make for 4-stop (408 kg. 6 person gearless motor having contract speed of 1.00 metre/Sec (approx.) serving different floor in the existing lift shaft