Public Works Roads Department Tender

Embankment Construction with Material Obtained from Borrow Pits (Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 (I) Private Land.

Construction of Sub grade and Earthen shoulders (Construction of Sub grade and Earthen shoulder with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300.2 with a lead upto 1000 m as per Technical Specification clause 303.1 (i) Private Land.

A) By Mix in Place Method. Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (A) By Mix in Place Method ii) For Grading II Material G.S.B. Gr-II (150 mm)

Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 KN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. (A) By Mannual Means II) Grading III b) Using Screening Type-A (13.2mm Agg.) W.B.M - III (75 mm)

Providing and laying interlocking concrete block pavement (M 40) having thickness 80mm as per technical specification clause 1504 including carraige a) Including Edge block/ Edge restraints. I.C.B.P. (80 mm)

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Retro-reflectorised Traffic sign (Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. (ii) 60 cm equilateral tringle

Retro-reflectorised Traffic sign (Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. (iii) 60 cm circular

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. Rate as per SOR Rural roads- 2020-21. (v) 60 cmx 60 cm Square

Kilo Metre Stone (Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 ii) Ordinary Kilometer Stone (Precast).

Kilo Metre Stone (Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 iv) 200 m stone (precast)

Planting of Trees and their Maintenance for one Year (Planting of Trees and their Maintenance for three Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for three year.

RCC Guard Post: Supplying, fitting and fixing RCC guard post 150cm long erected 75cm above the ground and 75cm below the ground with M-15 grade (nominal mix 1:2:4 with broken stone aggregate up to 20mm size) of cement concrete and required reinforcement tied in position with annealed black wire including centering, moulding the top, curing including painting concrete surfaces in 23cm strips upto 0.75m from the top alternately in black and white and having 2 nos. reflective band of desired shade etc. complete as per design and as directed. a) 15 cm dia. RCC guard post with reinforcement of 4nos. 12mm dia TMT main steel bars and 6mm TMT/ MS stirrups at 15cm c/c.

(RCC Box Cell Culvert)Earth work in excavation of foundation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal up to a lead of 50m, dressing of sides and bottom and backfilling in tranches with excavated suitable material. i) Ordinary Soil (i) upto 3.00 m depth

Sand Filling in foundation trenches as per drawing and Technical Specification 305.3.9

PCC 1:3:6 in foundation. Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203. A. With Crushed Stone : i) PCC Grade M10 (i) Nominal Mix 1:3:6

PCC 1:2:4 in foundation. Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203. A. With Crushed Stone : iii) PCC Grade M20 (i) Nominal Mix 1:2:4

Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications Clauses 802, 804, 805, 806, 807, 1202 &1204. A. WithCrushed stone iv) RCC GRADE M25 (i) Height up to 5m

Providing & Laying Reinforced Cement Concrete in Superstructure complete as per drawing and technical specifications Clauses 800, 1205.4 & 1205.5. A. WithCrushed stone iv) RCC GRADE M25 (i) Height up to 5m

Supplying, fitting and placing TMT reinforcement(Fe 415) in sub structure complete as per drawings and technical specifications Clauses 1002, 1005, 1010 & 1202.

Supplying, fitting and placing TMT reinforcement in super structure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202.

Providing and laying cement concrete wearing course M30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 A. With Crushed stone :

Providing weepholes in brick masonry/ stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of structures with slope of 1(V) : 20(H) towards drawing force complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Back filling behind abutment, wing wall and return wall complete as per drawings and technical specification Clause 1204.3.8 A. Sandy Materials

Providing and laying curtain walls complete as per drawing and Technical Specifications Clause 1304. iii) Cement concrete grade M10

Construction of flexible apron 1m thick comprising of loose stone boulders weighing not less than 25 kg beyond curtain wall.

Painting two coats including primer coat after filling the surface with synthetic enamal paint I all shades on new, plastered/ concretes surfaces as per drawing and technical specification clause 1701.