Public Works Roads Department Tender

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.(ii) For Grading II Material

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3-wheels steel/vibratory roller 8-10 tonnes in stages to proper grade & camber,applying & brooming,stone screening/binding materials to fill up the interstics of coarse aggregates,watering & compacting to the required density,Grading-II as per Technical Specification,Clause-405.A. By manual means

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3-wheels steel/vibratory roller 8-10 tonnes in stages to proper grade & camber,applying & brooming,stone screening/binding materials to fill up the interstics of coarse aggregates,watering & compacting to the required density,Grading-III as per Technical Specification,Clause-405.A. By manual means

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 i) Low porosity

Providing and applying Tack Coat with bitumen emulsion pressure distributor at the rate 0.20-0.25 Kg/Sqm on the prepared bituminous / granular surface cleaned with mechanical broom as per technical specification.Clause-503 (b) dry & hungry bituminous surface(Two coats)

Providing and laying Semi Dense bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 % of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.508. complete in all respect.(A) With hydrated lime/cement as filler ( refer table 500-9 of MoSRT&H specification),a)(I)'with 60/70 or VG-30 grade bitumen,(ii) for GradingII(10 mm nominal size)

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Providing & applying boulder apron laid in wire crates with 4mm dia. G.I.wire conforming to IS:280 & IS:4826 in 100mmx100m mesh (wooven diagonally) including 10% extra for laps & joints laid with stone boulders weighing not less than 40kg each)

Providing and laying pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302(I)Stone Boulder