Public Works Building And NH Department Tender
... More
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 55,331Document Cost
₹ 560Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_PWBNH_43651_1Tender No
DDTBDD/C/S/S-8/2024-25/2780Tender Authority
Public Works Building And NH Department ViewPurchaser Address
-Website
http://assamtenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
21.10 Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.
17.76
4013
-
... More
9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).
9.1.3 Kiln seasoned and chemically treated hollock wood
0.18
74199
-
... More
Civil Works
-
-
-
... More
2.27 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
107.25
2161
-
... More
Installation of Sign Board
-
-
-
... More
9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.
9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc.
319.68
197
-
... More
Sign Board
1
7000
-
... More
6.12 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in :
6.12.2 cement mortar 1:4 (1 cement : 4 coarse sand)
123.11
837
-
... More
5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts
61.2
804
-
... More
5.9 Centering and shuttering including strutting, propping etc. and removal
of form for
5.9.1 Foundations, footings, bases of columns, etc. for mass
concrete
38.08
307
-
... More
6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand)
12.48
6882
-
... More
12.4 Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.
12.4.2 0.63 mm thick with zinc coating not less than 275 gm/m²
24.5
750
-
... More
13.41 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :
13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer
244.9
162
-
... More
13.2 15 mm cement plaster on the rough side of single or half brick wall of mix
13.2.2 1:6 (1 cement: 6 fine sand)
246.21
324
-
... More
5.1 Providing and laying in position specified grade of reinforced cementconcrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de
rived from natural sources)
14.05
8364
-
... More
10.16 Steel work in built up tubular (round, square or rectangular hollow tubesetc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
10.16.1 Hot finished welded type tubes
50 x 50 x 5mm and 40 x 40 x 5mm
3581.03
154
-
... More
11.2 Dry brick on edge flooring in required pattern with bricks of class
designation 7.5 on a bed of 12 mm mud mortar, including filling joints
with Jamuna sand, with common burnt clay non modular bricks.
270.08
733
-
... More
4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
7.24
6833
-
... More
5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers
128.8
608
-
... More
5.2 Reinforced cement concrete work in walls (any thickness), including
attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size
derived from natural sources)
9.51
10185
-
... More
9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.
9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
6.62
3086
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements