Public Works Building And NH Department Tender

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 fine sand)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

upplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. Premium model 1200 mm Sweep

Supplying with installation testing and commissioning of 5 STAR rating Split type air conditioner of the following capacity complete with all accessories as directed by the department.

Supplying and erection of galvanised stay set for 11 KV over head lines complete with 19/ 20 mm dia X 1.8 metres long stay rod, anchor plate of size 45 cm X 45 cm X 7.5 mm thick, thimble, stay clamps, turn buckle ( 20 mm X 600 mm ), 7/ 4.00 mm dia G.I. stay wire and 11 KV strain insulator etc in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size ) foundation including excavation and refilling etc. as required.

Supplying and erection of 11 KV pin insulator complete with large steel head G.I. pin, nuts, washers etc. as required.

Supplying and erection of 11 KV disc insulator for 11 KV over head lines with galvanised insulator fittings, ball and socket type and complete with galvanised strain clamps, bolts, nuts, washers etc. as required.

Supplying and erection of three piece nonlinear resistor type lightning arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharge current rating of 5 KA and complete with galvanised clamping arrangement, G.I. bolts, nuts, washers etc. as required.

Supplying of two lengths of channel iron 75 mm X 40 mm X 6 mm (7.14 kg per metre) double pole cross arm for three wire 11KV over head line conductors complete with through bolts and nuts for clamping to the poles, 50 mm X 6 mm M.S. flats welded on one side to the channel iron and with bolts and nuts on the other side for tying the cross arms together, including drilling holes for insulator pins/ fittings, bolts, nuts and washers etc (as per drawing) and painting with primer and finish paint as required.

Supplying, Installation, testing and Commissioning of40 KVA 3 Phase Diesel Generator Set Model H4G4DE40, ALTERNATOR LEROYSOMAR/CGL, ( Leiland or equivallent make as directed by the department.

Providing and fixing at approved location approved make 125 Amp. Panel mountinng open execution Change Over Switch (Indoasian/Crompton/Havell's /HPL or equivallent make as directed.

Supplying with fitting and fixing of 11 KV D.O. Fuse set 200 Amp assembly as required and specified by the department.

Gang operated switch SL No. 519, Code: 107288, HSN Code: 8536, 11 KV DO Fuse, 400 AMP Assembly ( APDCL approved rate.)

Supplying, installation of 3 Phase 4 wire ICS, DLMS, 3 x 240 V , 40 - 200 Amp, Class 1.0 thread through energy meter for distribution transformer metering ( Category - A & C ), S.L. No. 511, Maaterial code - 200236, HSN Code - 9028 as approved by the deptt.

Supplying, installation DTR Fencing as per REC Standard specification complete with materials and labour as approved by the deptt.

Supplying Fitting & Fixing ACSR " Raccon " , Materials Code : 103057, HSN Code : 7604 ( Rate considered from APDCL approved rate sl. No. 447/21)

Supplying & Installation of GI Steel tubuler Pole (SP-56) of Length 11.00 Mtr. SL NO. 751, CODE 101083, HSN CODE 7308 as approved by the deptt.

Construction of RCC Diesel Generator PAD as per Specification & Design of this department complete as directed by the department (Transformer Pad for 2.5 MVA complete as per specification) T/R rate

Construction of RCC Transformer Pad asper Specification & Design of this department complete as directed by the Department.T/R rate

Supplying with fitting and fixing Water Heater ( Geyser) of 15 Ltr. Capacity , Puro Ex Product Code : GHWAPPTWB 0 15 Colour White Blue, HSN Code- 8516 of Havells or equivallent make" as required and specified and directed by the department.

Supplying with fitting and fixing Sine Wave New Optimus 1250 Luminous inverter with Luminous Battery, Tall Tubular , Model ILTT25060, or equivallent make" as required and specified by the department.

Supplying with fitting and fixing Kitchen Chymney " KUTCHINA VISTA'', auto clean or equivallent make" as required and specified and directed by the department.

Supplying with fitting and fixing Water Filter ( Aqua Guard Neo RO+UV or equivallent make" as required and specified and directed by the department.

Supplying with installation & testing and commissioning of Voltage Stabilizer for one inverter AC upto 1.5 Ton or 18000 BTU/Hour, Time delay 3 minutes +- 20 Sec. ITDS, working range 160 VAC to 280 VAC, 12 Amp Capacity, Model VI 4160, Warrenty 3 years, Make V- GUARD or Equivallent make as required and directed by the Department.

Supplying with fitting & fixing of Motor Starter Switch 240V - 50 Hz complete with necessary electrical connection etc. as required and as directed by the department ( Havell's/Bajaj or equivallent make ) 25 AMPS . ( 4 Nos. for A/C & 4 Nos. for Geyser )

Supplying , Installation & Commiissioning of Submerssible Motor Pump Set Single Phase, 2HP (1.5 KW) Pipe size 50 MM, Stage 10,Head Range 61m-32m , Discharge range 60L-175L/ Min, Capacitor start/Capacitor run Havells product Code: MHPLDJ 1002 & Model: HC4010D20S OR Equivallent make as required & Directed by the Department. Rs,

Supplying , Installation & Comm. of Control Panel for Submerssible Motor Pump Set Single Phase, 2HP (1.50 KW) , Capacitor start 72MF /Capacitor run 150/200MF Havells product Code: MHPZYS2 X00 & Model: 2.0 HP-1PH-V4 W/F CP SUB PUMP HAVELLS OR Equivallent make as required & Directed by the Department.

Supplying with fitting and fixing 2.5 SQ MM Flat Three Core PVC insulated & PVC Sheathed Industrial Cable for Submersible Pump Motors 1100 Volts , conforming to IS 694 " ( Make Havells/Finolex/ATC/RR or Equivallent) as required and specified by the department.

Providing and fixing Mechanical foam type fire extinguisher consisting of welded MS cylinderical body squeeze lever discharge valve , 30 cm long high pressure discharge hose, discharge nozzle, suspension bracket etc. complete. Capacity 9kg for pump room& DG set

Providing and fixing stored prussure ABC fire extinguiser consisting of welded MS cylindrical body squeeze lever discharge valve, 30cm long high pressure discharge hose, discharge nozzle,suspension bracket etc complete. Capacity 6 kg

Providing and fixing carbon-di-oxide fire eextinguiser consisting of welded MS cylindrical body squeeze lever discharge valve, 30cm long high pressure discharge hose, discharge nozzle,suspension bracket etc complete. Capacity 4.5 kg

Providing and fixing at approved location approved make 4 nos fire buckets of 24 gauge galvanised steel, painted white inside and red outside and black on the bottom, inscribed with letters FIRE in black and gold including stand etc complete

Pole type BOP or equivallent 8030 Height, 8.50 Mtr. ( Rate as per O. estimate )

Analysys of Rate for Supplying fitting & fixing Double Arm Bracket of Length 1500 mm ( Make : NEZONE/ CROMPTON/ BAJAJ/PHILIPS or Equivallent as approved by the APWD/CPWD )

45 Watt LED Street Light : ( Crompton /Havells /Philips or equivallent Make) ( Rate as per o. Estimate )

Supplying of following sizes XLPE insulated and PVC sheathed aluminium conductor armoured power cable of 1.1 KV grade conforming to IS 7098 (Part - I) / 1988 with amendment up to date etc as required. : Twin Core,2 x 6 SQ MM armoured UG Cable : ( For Street Light )