Public Works Building And NH Department Tender

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Providing and laying in position ready mixed or site batched design mix concrete for plain cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge for the following grade of concrete. Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Note : (1) Excess/less cement used than specified in this item is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement is to be ensured in accordance with clauses 5.2 and 5.2.1 of IS: 456 -2000 in the items of BMC and RMC." All works upto plinth level : Concrete of M10 grade with minimum cement content of 220 kg/cum

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position ready mixed or site batched design mix concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering , finishing and reinforcement as per direction of the engineer-in-charge for the following grade of concrete. Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg/cum

Providing and laying in position ready mixed or site batched design mix concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland / Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/ retard setting of concrete, to improve durability and workability without impairing strength;' including pumping of concrete to site of laying, curing, carriage for all leads, but excluding the cost of centering, shuttering , finishing and reinforcement as per direction of the engineer-in-charge for the following grade of concrete. Note : Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content , the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg/cum

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement Mortar 1:6 (1 cement : 6 coarse sand).

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry with 150mm/230mm/300 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing and laying Autoclaved Aerated concrete (AAC) blocks masonry 100 mm/ 125 mm thick with Grade-I AAC blocks of density 551 to 650 kg/ cum conforming to IS: 2185 (Part 3) in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of Slab over 0.50sqm

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick.

Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture Stainless Steel 304 grade CYLINDRICAL LOCKS - CLASSIC LOCK. Complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 300 mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Tower bolt 250mm long with 10mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade wall mounted door buffer fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Door Stopper - door mounted hanging type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m²

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand)

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) and a top layer 6 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) finished rough with sponge.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Painting with synthetic enamel paint, having VOC (Volatile Organic Compound) content less than 150 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats.

Providing & fixing 150mm wide Chicken wire mesh on joints of RCC & Brick work before plastering complete in the direction of Engineer-in-charge.

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : For fixed portion Powder coated aluminum (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminum (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Filling the gap in between aluminum frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing hand shower (Health faucet) with 1.2mtr long with 8mm dia Easy Flex Tube with wall hook and flow restrictor with flow rate 6 litre per minute at 3 bar in chrome finish and wall hook.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing & fixing toilet paper holder C.P. brass

Providing and fixing soil waste vent & rain water pipes 100 mm dia. Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron/ centrifugally cast iron(spun) pipes embedded in and including cement concrete blocks 10x 10 x 10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls, etc. For 100mm dia pipe

Providing and fixing bend of required degree with access door insertion rubber washer 3mm thick, bolts and nuts complete 100 mm dia Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing plain bend of required degree: 100 mm dia Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent, arm complete, including cost of cutting and making good the walls and floors. 100mm inlet and 100mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia .Pipes.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External Work 25mm nominal nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External Work 32mm nominal nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixture and geyser points of approved quality confirming to IS: 8931.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S (non modular) bricks of class designation 7.5

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete: 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design: 150 mm diameter S.W. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610mm internal dimensiions total weight of cover and frame to be not less than 38 Kg. ( weight of cover 23 Kg. and weight of frame 15 Kg.), with FPS bricks with class designation 7.5 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2x1.5 sq mm + 1x1.5 sq mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2x6 sq mm + 1x6 sq mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 4x6 sq mm + 2x6 sq mm earth wire

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone Socket Outlet

Supplying and fixing following size/ modules, GI box along with modular base and cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)

Supplying and fixing of following sizes of STEEL conduit alonwith the accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 20mm dia

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way Double Door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 Way (4+24), Double Door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole and neutral

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Double pole

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 Amps

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of Outdoor type cubicle type totally enclosed free standing type moisture, dust and vermin proof made out of 2.0 mm thick & front cover 2.0 mm thick CRCA sheet complete with following equipments including internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. All the incomming and outgoing MCCB shall have 25 KA Ics=Icu. All the MCCB up to 250 Amp shall have thermal release with adustable overload and short circuit protection and above shall have microprocessor release with adjustable overload, short circuit protection. Feeder pillae mounting MS Stand made out of 50mmx50mmx6mm Angle and all the civil work related to installation of Feeder piller shall be part of items. FEEDER PILLAR-1 INCOMING 1 No 400 Amp TP+N Moulded Case Circuit Breaker 1 Set of phase indicating lamps with Single Pole MCB. 1 Set of ON / OFF indicating lamps with Single Pole MCB. BUS BAR 500 Amp TPN aluminium bus bar. OUTGOING 04 Nos 160 Amp TP+N Moulded Case Circuit Breaker 1 Lot of control / power wiring. Feeder Pillar -1 described as above

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of Outdoor type cubicle type totally enclosed free standing type moisture, dust and vermin proof made out of 2.0 mm thick & front cover 2.0 mm thick CRCA sheet complete with following equipments including internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. All the incomming and outgoing MCCB shall have 25 KA Ics=Icu. All the MCCB up to 250 Amp shall have thermal release with adustable overload and short circuit protection and above shall have microprocessor release with adjustable overload, short circuit protection. Feeder pillae mounting MS Stand made out of 50mmx50mmx6mm Angle and all the civil work related to installation of Feeder piller shall be part of items. FEEDER PILLAR-2 INCOMING 1 No 630 Amp TP+N Moulded Case Circuit Breaker 1 Set of phase indicating lamps with Single Pole MCB. 1 Set of ON / OFF indicating lamps with Single Pole MCB. BUS BAR 800 Amp TPN aluminium bus bar. OUTGOING 06 Nos 160 Amp TP+N Moulded Case Circuit Breaker 1 Lot of control / power wiring. Feeder Pillar -2 described as above

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of Outdoor type cubicle type totally enclosed free standing type moisture, dust and vermin proof made out of 2.0 mm thick & front cover 2.0 mm thick CRCA sheet complete with following equipments including internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. All the incomming and outgoing MCCB shall have 25 KA Ics=Icu. All the MCCB up to 250 Amp shall have thermal release with adustable overload and short circuit protection and above shall have microprocessor release with adjustable overload, short circuit protection. Feeder pillae mounting MS Stand made out of 50mmx50mmx6mm Angle and all the civil work related to installation of Feeder piller shall be part of items. FEEDER PILLAR-3 INCOMING 1 No 400 Amp TP+N Moulded Case Circuit Breaker 1 Set of phase indicating lamps with Single Pole MCB. 1 Set of ON / OFF indicating lamps with Single Pole MCB. BUS BAR 500 Amp TPN aluminium bus bar. OUTGOING 05 Nos 160 Amp TP+N Moulded Case Circuit Breaker 1 Lot of control / power wiring. Feeder Pillar - 3 described as above

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of Outdoor type cubicle type totally enclosed free standing type moisture, dust and vermin proof made out of 2.0 mm thick & front cover 2.0 mm thick CRCA sheet complete with following equipments including internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. All the incomming and outgoing MCCB shall have 25 KA Ics=Icu. All the MCCB up to 250 Amp shall have thermal release with adustable overload and short circuit protection and above shall have microprocessor release with adjustable overload, short circuit protection. Feeder pillae mounting MS Stand made out of 50mmx50mmx6mm Angle and all the civil work related to installation of Feeder piller shall be part of items. FEEDER PILLAR-4 INCOMING 1 No 400 Amp TP+N Moulded Case Circuit Breaker 1 Set of phase indicating lamps with Single Pole MCB. 1 Set of ON / OFF indicating lamps with Single Pole MCB. BUS BAR 500 Amp TPN aluminium bus bar. OUTGOING 05 Nos 160 Amp TP+N Moulded Case Circuit Breaker 1 Lot of control / power wiring. Feeder Pillar - 4 described as above

Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of Outdoor type cubicle type totally enclosed free standing type moisture, dust and vermin proof made out of 2.0 mm thick & front cover 2.0 mm thick CRCA sheet complete with following equipments including internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. All the incomming and outgoing MCCB shall have 25 KA Ics=Icu. All the MCCB up to 250 Amp shall have thermal release with adustable overload and short circuit protection and above shall have microprocessor release with adjustable overload, short circuit protection. Feeder pillar mounting MS Stand made out of 50mmx50mmx6mm Angle and all the civil work related to installation of Feeder piller shall be part of items. FEEDER PILLAR-5 INCOMING 1 No 630 Amp TP+N Moulded Case Circuit Breaker 1 Set of phase indicating lamps with Single Pole MCB. 1 Set of ON / OFF indicating lamps with Single Pole MCB. BUS BAR 800 Amp TPN aluminium bus bar. 05 Nos 160 Amp TP+N Moulded Case Circuit Breaker 01 Nos 100 Amp TP+N Moulded Case Circuit Breaker 1 Lot of control / power wiring. Feeder Pillar - 5 described as above

EXTERNAL LIGHTING PANEL- INCOMING 1 No. 63 Amp FP ( 35 KA Ics) Moulded Case Circuit Breaker.1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch. 1 No. 63 Amp digital ammeter with inbuilt selector switch and CT's. 1 Set of phase indicating lamps with Single Pole MCB. 1 Set of ON / OFF indicating lamps with Single Pole MCB. 1 Set 24 Hrs TSQ Timer 1 Set 63 Amp, 4P Contactor & A/M switch and Push Button. BUS BARS 100 Amp TPN aluminium busbar. OUTGOING 16 No. 25 Amp DP MCB. 04 No. 40 Amp DP MCB. 02 No. 40 Amp FP MCB. Panel described as above

Supply and installation of 300 mm, 230 v A.C. exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required.

Supply and installation of 400 mm, 230 v A.C.wall/cabin fan including fixing the bracket, making connection, testing, commissioning etc as required.

Supply, Installation, Testing & Commissioning of surface mounted Linear Batten 40W luminaire with high performance extruded aluminium channel housing for efficient heat dissipation.High efficiency long life LED package in integral module with system lumen efficacy of 100 lm/W and viewing angle of 120° to ensure better uniformity. Powered by an independent Isolated, SELV Output electronic LED driver with Output Short-circuit protection, Surge protection & other reliability test. Lumen Output of 4550 lumens.CRI 80, Color temperature 6500K, THD 10% and PF 0.95 ,IP20, IK03. Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:3 KV;

Supplying and fixing single wall mounted 36 watt LED type batten fitting complete with electronic driver and LED tube etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.

Supplying and fixing Surface mounted 70 watt LED High bay vertical downlighter complete with all accessories and replaceable electronic driver, directly on false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 50 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required

11 KV HT VCB SIX BREAKER PANEL BOARD (INDOOR TYPE) (2 INCOMMING + 4 OUTGOING) Design, manufacturer, supply of panel board fabricated out of minimum 2 mm thick sheet steel as per specifications. The panel shall be complete with cable termination arrangement suitable for incoming and outgoing each 1 run x 3C x 240 Sqmm XLPE 11 KV cable and copper bus bar arrangement. The panel shall comprise of the following: Supply, Receiving, Unloading, Shifting, Installation Testing & Commissioning of 11 KV Four Breaker Vacuum Circuit Breaker Panel Board as 1 Incomming & 3 Outgoing shall be metal clad floor mounting complete as per specification and as described. 630 A Vacuum circuit breaker of 18.3 KA RMS for 1 second ruputuring capacity for at 11 KV rated, totally enclosed,air insulated metal clad housing, floor mounting, horizontal isolation, vermin proof, fully interlocked horizontal drawout type having isolation features and control devices complete with the following. Manually and motor operated, spring charged (release closing mechanism) trip free type,triple pole truck mounted draw out, vacuum circuit breaker, incorporating mechanical as well as electrical ON/OFF indication. Spring charge/discharge mechanical indication"OFF" push buttons for emergency trip (shrouded) test/service position limit switches with 6 NO/6 NC breaker auxilliary contacts in service position, 24 Volts DC shunt trip coil and strip heater to prevent moisture absorption. Six Panel Board ( 2 I/C + 4 O/G Each Incomer Panel shall have following:- 1 No. 11kV 630A 25kA drawout type VCB with motorised spring charge mechanism for 240V AC, closing & tripping coils suitable for 24V DC, Each incomer comprising with following accessaries. 1 No. Mechanical ON/OFF Indicator,1 No. Aux Switch 6NO + 6NC,Panel, Busbar, CT, PT, 600A color coded heat shrinkable sleeved TP Copper busbar of 18.3 KA fault rating. 1 No. Fully compartmentalised sheet steel enclosure floor mounting type with automatic safety shutters, independent pressure discharge flaps, PVC sleeved busbar, etc with provision for terminating PVC/PILC/XLPE Cable,3 Nos. Resin Cast CTs 150-75/1-1A with Core 1 : 7.5VA CL 1, Core 2 : 7.5VA CL 5P10 ,3 Nos. PT - 33kV/√3//110/√3V ,CL 1.0, 100VA ,Breaker Panel indication Lamps :6 Nos. ON/OFF/TRIP/TRIP Ckt Healthy/Spring Charged Switches and other Accessories, 8 nos.Fuses, 1 No. Heater, 1 No. Thermostat, 1 No. 6 Window Annunciator, 1 No. Plug & Socket, 1 No. Test Terminal Block, 1 No. T-N-C Switch1 No. Emergency Push Button, 1 No. Local/Remote Selector Switch, Meters, 1 No. Analog Ammeter + ASS, 1 No. Analog Voltmeter + VSS, 1 No. Digital Multifunction Meter - Quasar, Relays, 1 No. MC 61A (O/C + E/F - IDMT+Inst), 1 No. AVAJH13 Master trip relay (Ashida), 1 No. TCS Relay, Note: All spare contacts of breaker or any other equipment inside the breaker shall be wired upto the outgoing terminal strip with appropriate ferrules / coding. The terminal strip rating shall be suitable for connecting two wires of 2.5sqmm subjected to providing minimum size strip suitable for 4/6sqmm. 1 Set of Power Pack 220 Volt A.C. / 24 Volt D.C. complete as required. Each Outgoing Panel shall have following:- 1 No. 11kV 630A 18.3kA drawout type VCB with motorised spring charge mechanism for 240V AC, closing & tripping coils suitable for 24V DC Each Outgoing comprising with following accessaries. 1 No. Mechanical ON/OFF Indicator, 1 No. Aux Switch 6NO + 6NC, Panel, Busbar, CT, PT, 600A color coded heat shrinkable sleeved TP Copper busbar of 18.3 KA fault rating,1 No. Fully compartmentalised sheet steel enclosure floor mounting type with automatic safety shutters, independent pressure discharge flaps, PVC sleeved busbar, etc with provision for terminating PVC/PILC/XLPE Cable. 3 Nos. Resin Cast CTs 40-20/1-1A with Core 1 : 7.5VA CL 1, Core 2 : 7.5VA CL 5P10 Breaker Panel indication Lamps : 6 Nos. ON/OFF/TRIP/TRIP Ckt Healthy/Spring Charged Switches and other Accessories, 8 nos.Fuses, 1 No. Heater, 1 No. Thermostat, 1 No. 6 Window Annunciator, 1 No. Plug & Socket, 1 No. Test Terminal Block, 1 No. T-N-C Switch, 1 No. Emergency Push Button, 1 No. Local/Remote Selector Switch, Meters, 1 No. Analog Ammeter + ASS, 1 No. Digital Multifunction Meter - Quasar, Relays, 1 No. MC 61A (O/C + E/F - IDMT+Inst), 2 No. Auxiliary Relay for transformer fault1 No. TCS Relay 1 Set of Power Pack 220 Volt A.C. / 24 Volt D.C. complete as required. Note: All spare contacts of breaker or any other equipment inside the breaker shall be wired upto the outgoing terminal strip with appropriate ferrules / coding. The terminal strip rating shall be suitable for connecting two wires of 2.5sqmm subjected to providing minimum size strip suitable for 4/6sqmm.It shall also be with 1 No. Earthing Truck for cable & Busbar earthing. H.T. Panel described as above (Six Breaker Panel)

Design, Manufacture, Supply, Installation, Testing and Commissioning of Package Substation 500 KVA, 11 KV /0.415 KV, 3 phase, 50 Hz delta/star-11 connected, copper wound transformer, oil immersed ONAN cooled, RMU having 2 Load Break Switch + 1 Breaker on HT Side Busbar on LT Side only complete with all fittings such as oil conservator, silica gel breather, thermometer, explosion vent with On Load Tap changing (OLTC) arrangement on HV side with Tapping for variations of high voltage from (+) 5% to (-)15% in steps of 1.25% each with integrated microprocessor based RTCC Panel, bi-directional roller, diagrams & rating plate, Oil temperature indicator, & Winding temperature indicator, Buchholz relay, weather proof Marshalling Box, lifting lugs, first filling of oil, weather proof H.Tcable box & L.T Bus duct arrangement etc. complete as per specification. All relays, contacts & CT terminals to be wired upto marshalling box. Transformer losses shall be as per latest IS code 1180, Level-2.

DIESEL GENERATING SET: CPCB-2 Design, Manufacturing, Testing at works, Supply, Installation, Testing & Commissioning of diesel engine of following rating on common base frame alongwith ECP & other accessories like hospital silencer, antivibration pad, batteries with leads, day oil fuel tank, suitable space heater for alternator, suitable amended arrangement for bus duct termination etc. as per EPC Tender specification. The entire work shall confirm to Bureau of Indian Standards safety standards; British Standards, and CPWD specifications. DG Set shall have synchronizing facility. The D.G. Set shall be Air cooled with Radiator Working at ambient temperature between -5°C to 50°C and relative humidity upto 95%. Nominal output voltage of engine/alternator set shall be 415 volts 50 Hz AC Supply with manual adjustment at all conditions of load with coarse and fine controls with a range of ± 5%. The frequency shall be maintained at 50 Hz ± 2% for the set. The output wave-form shall be sinusoidal at all load conditions. The engine/alternator set shall be capable of taking 10% over-load for a period of one hour during any 12 hours period, while operating continuously at full rated load. The Engine shall be capable to minimum 60% bulk load of the rating during transfer of the load from NO Load position without tripping. The set may be idle for a long time except for periodical test whenever there is a electrical supply failure, the set may required to run continuously for period even exceeding 24 hours. Engine should have minimum lube oil change period 500 Hrs. The set shall have vibration limit less than 130 microns (as per BS:4999 Part – 142) & noise level shall be meet CPCB norms under all conditions of load. The efficient residential silencer shall be provided with or without catalytic converter on-line scrubber & the set shall meet EURO-II norms for D.G Sets, for the exhaust. Air inlet shall also be provided. The engine shall be stationary, compression ignition, totally enclosed, water cooled, 4 stroke direct injection, cold battery starting, turbo charged and low temperature with after cooled Radiator Cooled 1500 RPM in accordance to BS 5514 and IS: 10002 complete with all accessories. The DG engine shall be suitable for quick start & should be able to pick up 100% load within optimum time. The DG Engine & the batteries shall be designed to take up at least six starting attempts beyond which the system shall be protected by means of an over crank relay. The successful bidder will submit GFC drawings of the equipments/accessories selected for this work for the approval. The governor shall be Isochronous, electronic digital type with a steady state frequency variation of +/- .25%. The transient performance shall comply with ISO 8528-5, Class G3 requirements. The engine shall be water cooled heat exchanger type or radiator cooled depending on its capacity. DG Set shall be adequately designed for continuous operation on ambient conditions at 50 deg C. The alternator shall be brushless synchronous and suitable for 3 phase 415 Volts, 4 wire, 50 Hz, 0.8 PF, 1500 RPM. The alternator shall be suitable for coupling directly to the diesel engine It shall be Drip proof, screen protected as per IP-23. The alternator shall be single bearing type & self ventilating. The alternators shall be continuously rated and shall have class ‗H‘ insulation with a temperature rise restricted to that of class F designed and built to withstand tropical conditions. It shall generally conform to BS: 5000 (Part - 99) / standards listed above. The alternator shall be suitable for sustaining a 10% overload for 1 hour in any 12 hour period without injury. The terminal arrangement for alternator shall be suitable for Bus Duct connections of adequate size to deliver the full load of the alternator. The alternator shall also have a solid state type digital voltage regulator (D.V.R.) suitable for single running with control limits of 1% from no load to full load under normal load changes. It shall be of static type and complete with cross current compensation. The regulator shall be provided with voltage adjusting potentiometer, and shall be complete with all alarm contacts, internal wiring, etc. Self excited, self regulated and providing alternator output regulation at plus or minus 0.25%. The alternator shall be provided with a pilot-excited, permanent magnet-excited generator (PMG) for superior short circuit capabilities. Bidders to specify sustained short circuit current capabilities for up to 10 seconds. The alternator shall be provided with sealed Barings to give minimum service life of 40,000 Hours. The Bidders to specify the maximum rating of the motor that can be started direct on line without any base load, with 50% base load, restricting the Voltage depth to 20%. Day service fuel tank shall be made of 3 mm thick MS sheet of 990 litres capacity including HSD fuel handling piping with M.S. heavy class ERW piping (Class-C) conforming to IS : l239 with necessary clamps, supports, anti vibration mountings, hangers and fittings such as bends, tees, reducers etc. painted Note: a) First filling of the HSD shall be under the scope of contractor b) Ambient temperature for DG Sets operation is 40°C. c) DG Manufacturer/OEM shall coordinate with Main L.T. Panel supplier for synchronising of DG Set & auto start / auto stop functioning including testing & commissioning. d) The DG Set Manufacture/OEM to guarantee that DG Set shall generate minimum 4 units of Electric power per litre at loading ranging from 40% to 85% under site conditions. e) If Manufacturer does not have the Power command controller of Cumins PC 3.3 or equivalent then the supplier shall submit the synchronizing panel PLC based DG Sets and scope of integration of synchronization system with the proposed Main L.T. Panel. f) The liasioning for inspection & approval of the layout drawing, installation license from electricity supply authority, electrical inspector, permission for operation of DG Set, approval from Pollution Control Board etc. as required. 500 KVA DG set with suitable capacity of DO Tank describe as above

Supply, Installation & Testing of following sizes MS exhaust piping conforming to IS:3589 complete with all accessories such as bends, flanges, 2 coat primer / painting etc. 250 mm dia MS pipe. (6.0 mm thick)

Supply & Fixing of Insulation of above pipe with 50 mm thick Loosely bound resin (LBR) mattress/ mineral wool/ Rockwool, density not less than 120 kg/m3 and aluminium cladding of 0.63 mm thick on exhaust pipe complete as per technical specification. 250 mm dia MS pipe.

Fabrication, supply & erection of MS structure for supporting of DG emission, exhaust piping with RCC foundation and in cable trench for cable support etc. complete in all respect.

Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652-2006.

Main LT Panel-1, 2, 3 with Interconnected Buscoupler Supply, Receiving, Unloading, Shifting, Erection, Testing & Commissioning of Main LT Panel. This will be floor mounted, free standing, compartmentalized, indoor duty, dust proof, vermin proof, front operated, electrical panel fabricated, painted and manufactured exactly as per specifications laid in this document and will be complete with the main and auxiliary bus bars, interconnection, earth terminals, earth bus and will be powdered coated finished. All the busbar joint shall be protected by clip on type sleeve. The DG control panel shall use all draw out 3 position withdrawn type breakers suitable for 415 V AC, 3 phase, 50 Hz, 4 wire supply system and will have fault level of 50 KA or as required as per consultant approval. The panel will be made as per detailed specifications and drawings forming part of this document. (Under no case temperature of LT Panel shall be more at any point of the panel, otherwise necessary exhaust fan shall be have to provided) Bus bar calculations considering temperature derating, enclosure derating, sleeving derating must be done and submitted for checking. Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. All the MCCB up to 250 Amp shall have thermal release with adustable overload, short circuit & earth fault protection and above shall have microprocessor release with adjustable overload, short circuit & earthfault protection. The panel shall be manufactured as per BOQ, tech specification and drawing. Fault level of panel shall be 25 KA. One set of PLC with required accessories for AMF, Load Management, Interlocking and synchronizing through synchronizing relay. PLC shall be with PC, Monitor, required software to monitoring the all parameters for Synchronizing Panel & Main L.T. Panel. Incomer: 3 No. Incomer and Each incomer breaker feeder shall have following: (For 500 KVA D.G. Set)- 800 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker microprocessor based releases for O/C, S/C & earth fault protection with instantaneous. (50 KA)One set of Generator control relay for Each D.G. Set with accessories for AMF. 3 No. indicating lamps to show the incoming power along with HRC fuses. 1 No. digital ammeter, ammeter selector switch, digital voltmeter, Voltmeter selector switch. 1 No. Load Manager EM 6400 with RS 485 port Announciation window to cover LLOP, HWT, OIL Pressure, U/V, O/V, U/F, O/F, O/C, E/F, REF relay faults shall be provided. 2 nos phase reversal relay shall be provided. Engine should trip on LLOP, HWT, oil temp, O/V, O/F and breaker should trip on other faults. Initially U/V & U/F will be bye passed till oil pressure is picked up. Indicating lights for ACB ON / OFF, ACB trip, neutral contactor ON, D.G. on mains, D.G. fails to start. Generator start /stop facility through push button from panel, necessary cranking relay shall be provided. Suitable battery charger for 24V 360 AH with d.c voltmeter & d.c ammeter. D.C voltmeter and ammeter will be analouge type. Whenever D.G. stop through PB, load shall be disconnected first. 3 No. Incomer and Each incomer breaker feeder shall have following: (For 500 KVA CSS)- 800 Amp FP Electrically operated hor 1 Nos. Digital Multifunction Meter with inbuilt Selector Switch & Protective SP MCB (96mm square) (one for each Incoming Breaker).izontal drawout type Air Circuit Breaker microprocessor based releases for O/C, S/C & earth fault protection with instantaneous. (50 KA) 1 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker). 1 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker). 1 Sets trip circuit healthy indicating lamp (one set for each incoming breaker). 1 Sets auto trip indicating lamp (one set for each incoming breaker). 1 Set of CT's one of 800/ 5Amp ratio for APFC relay. 1 Nos. master trip relay (one for each Incoming Breaker).1 Nos of Undervoltage & Overvoltage Protection. 1 Nos Phase reversal relay. 1 Nos 6 window announciator with complete accessories. 1 Nos TVSS with required accessories & protection. 3 No. Incomer and Each incomer breaker feeder shall have following: (From Standby Panel)- 800 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker microprocessor based releases for O/C, S/C & earth fault protection with instantaneous. (50 KA) 1 Nos. Digital Multifunction Meter with inbuilt Selector Switch & Protective SP MCB (96mm square) (one for each Incoming Breaker). 1 Sets of phase indicating lights (RYB) with protection fuses (one set for each incoming breaker). 1 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker). 1 Sets trip circuit healthy indicating lamp (one set for each incoming breaker). 1 Sets auto trip indicating lamp (one set for each incoming breaker). 1 Set of CT's one of 800/ 5Amp ratio for APFC relay. 1 Nos. master trip relay (one for each Incoming Breaker). 1 Nos of Undervoltage & Overvoltage Protection. 1 Nos Phase reversal relay. 1 Nos 6 window announciator with complete accessories. BUSCOUPLER 3 Sets of indicating lamps for ON & OFF for bus coupler. BUSBARS 1000 Amp TPN busbars of aluminium alloy as per SLD. OUTGOING EACH OUTGOING FEEDER SHALL HAVE DIGITAL ENERGY METER 02 Nos. 800 Amp FP EDO Air Circuit Breaker.02 Nos. 630 Amp TP+N Moulded Case Circuit Breaker. 11 Nos. 400 Amp FP Moulded Case Circuit Breaker. 03 Nos. 250 Amp FP Moulded Case Circuit Breaker. 02 Nos. 100 Amp FP Moulded Case Circuit Breaker. 02 Nos. 63 Amp FP Moulded Case Circuit Breaker. Notes: All outgoing feeders shall have suitable range Digital ammeter with selector switch, CTs and phase indicating light protected by 2 amps MCBs except capacitor feeders. All breakers shall be electrically/ mechanically interlocked as per schematic diagram. All outgoing shall be suitable for provision of shunt trip coil in future. All outgoing/incoming feeder shall have the provision for internal lighting. CT’s on R/Y phase for PFCR for each I/C feeder. Digital electronic KWH meter (modbus output protocol to BAS for energy management (Potential free contacts or remote indication).shall be provided all incoming as well as outgoing feeder All incoming as well as outgoing air circuit breaker shall be compatible with BAS system. All incoming / outgoing ACB/MCCB shall be suitable for minimum 50 KA (ICS) breaking capacity and as per the detailed specification Space heater with thermostate shall be provided in the above panel. BATTERY & BATTERY CHARGER 1 No. UPS for Interlocking Scheme. 3 SET, 150 KVAR CAPACITOR PANEL AND EACH SET CAPACITOR PANEL SHALL HAVE FOLLOWING- INCOMING 400 Amp TP+N Moulded Case Circuit Breaker. (Already considered in Main L.T. Panel Outgoing) 1 Nos. 0 to 500 Volt digital voltmeter with Voltmeter Selector Switch & Protective SP MCB (96mm square). 1 No. 0 to 400 Amp digital ammeter (96mm square) with CT's. 1 Sets of phase indicating lights (RYB) with protection fuses. 1 Sets breaker 'ON' & 'OFF' indicating lamp. 10 Step Automatic Power Factor Correction relay (APFC relay). BUSBARS 500 Amp TPN busbars of aluminium alloy as per SLD. OUTGOING 5 Nos. 63 Amp TP MCCB. 3 Nos. 32 Amp TP MCCB. 5 Nos. capacitor duty contactor (one for each 25KVAR capacitor unit).3 Nos. capacitor duty contactor (one for each 10/5KVAR capacitor unit). 5 Nos. 25 KVAR Capacitor Bank. 2 Nos. 10 KVAR Capacitor Bank. 1 Nos. 5 KVAR Capacitor Bank. 8 sets of push button stations Red and Green for manual operation of capacitor units with auto/manual selector switches. 1 No. Indicating lamp for each 25/10/5 KVAR capacitor unit to indicate that the unit is 'ON'. 1 No. Toggle switch for changing automatic to manual operation of capacitor units. Power factor meter. Main L.T. Panel Cum Capacitor Panel described as above

Standby Panel- (1x500 KVA DG Set) Supply, Receiving, Unloading, Shifting, Erection, Testing & Commissioning of Main LT Panel. This will be floor mounted, free standing, compartmentalized, indoor duty, dust proof, vermin proof, front operated, electrical panel fabricated, painted and manufactured exactly as per specifications laid in this document and will be complete with the main and auxiliary bus bars, interconnection, earth terminals, earth bus and will be powdered coated finished. All the busbar joint shall be protected by clip on type sleeve. The DG control panel shall use all draw out 3 position withdrawn type breakers suitable for 415 V AC, 3 phase, 50 Hz, 4 wire supply system and will have fault level of 50 KA or as required as per consultant approval. The panel will be made as per detailed specifications and drawings forming part of this document. (Under no case temperature of LT Panel shall be more at any point of the panel, otherwise necessary exhaust fan shall be have to provided) Bus bar calculations considering temperature derating, enclosure derating, sleeving derating must be done and submitted for checking. Each incoming / outgoing breaker shall have microprocessor release with adjustable over current, short circuit & earth fault protection with instantaneous as mentioned in specification. The Panel will be made as per detailed specifications & drawings forming part of this document. Fault level of panel shall be 50 KA. All the MCCB up to 250 Amp shall have thermal release with adustable overload, short circuit & earth fault protection and above shall have microprocessor release with adjustable overload, short circuit & earthfault protection. The panel shall be manufactured as per BOQ, tech specification and drawing. Fault level of panel shall be 25 KA. One set of PLC with required accessories for AMF, Load Management, Interlocking and synchronizing through synchronizing relay. PLC shall be with PC, Monitor, required software to monitoring the all parameters for Synchronizing Panel & Main L.T. Panel. Incomer: 1 No. Incomer and Each incomer breaker feeder shall have following: (For 500 KVA D.G. Set)- 800 Amp FP Electrically operated horizontal drawout type Air Circuit Breaker microprocessor based releases for O/C, S/C & earth fault protection with instantaneous. (50 KA) One set of Generator control relay for Each D.G. Set with accessories for AMF. 3 No. indicating lamps to show the incoming power along with HRC fuses. 1 No. digital ammeter, ammeter selector switch, digital voltmeter, Voltmeter selector switch. 1 No. Load Manager EM 6400 with RS 485 port Announciation window to cover LLOP, HWT, OIL Pressure, U/V, O/V, U/F, O/F, O/C, E/F, REF relay faults shall be provided. 2 nos phase reversal relay shall be provided. Engine should trip on LLOP, HWT, oil temp, O/V, O/F and breaker should trip on other faults. BUSBARS 1000 Amp TPN busbars of aluminium alloy as per SLD. Whenever D.G. stop through PB, load shall be disconnected first. Suitable battery charger for 24V 360 AH with d.c voltmeter & d.c ammeter. D.C voltmeter and ammeter will be analouge type. Generator start /stop facility through push button from panel, necessary cranking relay shall be provided. Indicating lights for ACB ON / OFF, ACB trip, neutral contactor ON, D.G. on mains, D.G. fails to start. Initially U/V & U/F will be bye passed till oil pressure is picked up. OUTGOING EACH OUTGOING FEEDER SHALL HAVE DIGITAL ENERGY METER 03 Nos. 800 Amp FP EDO Air Circuit Breaker. Notes: All outgoing feeders shall have suitable range Digital ammeter with selector switch, CTs and phase indicating light protected by 2 amps MCBs except capacitor feeders. All breakers shall be electrically/ mechanically interlocked as per schematic diagram. All outgoing shall be suitable for provision of shunt trip coil in future. All outgoing/incoming feeder shall have the provision for internal lighting. CT’s on R/Y phase for PFCR for each I/C feeder. Digital electronic KWH meter (modbus output protocol to BAS for energy management (Potential free contacts or remote indication).shall be provided all incoming as well as outgoing feederAll incoming as well as outgoing air circuit breaker shall be compatible with BAS system. All incoming / outgoing ACB/MCCB shall be suitable for minimum 50 KA (ICS) breaking capacity and as per the detailed specification Space heater with thermostate shall be provided in the above panel. BATTERY & BATTERY CHARGER 1 No. UPS for Interlocking Scheme. Main L.T. Panel Cum Capacitor Panel described as above

Supply & Laying of following sizes of 1.1KV grade multicore copper conductor PVC insulated and PVC sheathed armoured control cable conforming to IS:7098 (Part-I) 1988, including end termination with brass compression gland and copper lugs. 4 core, 1.5 sq.mm

Supply & Laying of following sizes of 1.1KV grade multicore copper conductor PVC insulated and PVC sheathed armoured control cable conforming to IS:7098 (Part-I) 1988, including end termination with brass compression gland and copper lugs. 8 core, 1.5 sq.mm

Supply & Laying of following sizes of 1.1KV grade multicore copper conductor PVC insulated and PVC sheathed armoured control cable conforming to IS:7098 (Part-I) 1988, including end termination with brass compression gland and copper lugs. 12 core, 1.5 sq.mm

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant). 3.5C x 25 Sq.mm

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant). 3.5C x 35 Sq.mm

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant).3.5C x 50 Sq.mm.

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant). 3.5C x 70 Sq.mm

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant). 3.5C x 95 Sq.mm.

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant). 3.5C x 120 Sq.mm.

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant). 3.5C x 150 Sq.mm.

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant). 3.5C x 185 Sq.mm.

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant). 3.5C x 240 Sq.mm.

Supply of following sizes of 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. (Cable shall be purchased only after approval of cable schedule by architect / consultant). 3.5C x 300 Sq.mm.

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3.5 X 25 sq. mm (28mm) For aluminium armoured cable

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3.5 X 35 sq.mm (32 mm) For aluminium armoured cable

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3.5 X 50 sq.mm (35 mm) For aluminium armoured cable

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3½ X 70 sq. mm (38mm) For aluminium armoured cable

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3½ X 95 sq. mm (45mm) For aluminium armoured cable

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3½ X 120 sq. mm (45mm) For aluminium armoured cable

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3.5 X 150 sq.mm (50 mm) For aluminium armoured cable

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3½ X 185 sq. mm (57mm) For aluminium armoured cable

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3½ X 240 sq. mm (63mm) For aluminium armoured cable

Supply & making end termination with brass compression gland & aluminium lugs for following size of FRLS insulated and FRLS sheathed aluminium conductor cable of 1.1KV grade as required. 3½ X 300 sq. mm (70mm) For aluminium armoured cable

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 95 sq. mm and upto 185 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/METAL pipe as required. Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonary duct as required. Above 185 sq. mm and upto 400 sq. mm

11 KV H.T. CABLE: Supplying of 11 KV grade aluminium conductor, cross linked polyethylene (XLPE) insulated individual core screened, flat steel/strip armoured PVC sheathed cable complete as required. 3C x 120 Sqmm, 11 KV XLPE

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required. 120 sq. mm

HT CABLE LAYING: Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required. Above 120 sq. mm and upto 400 sq. mm

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel at least 2 mm thick, vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x 610 mm and 45 cm deep for pipe line with three or more inlets. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber For 455x610 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber For 500x700 mm size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.200 mm dia (OD-200 mm & ID-175 mm nominal)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required.160 mm dia (OD-160 mm & ID-135 mm nominal)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 90 mm dia (OD-90 mm & ID-76 mm nominal)

Supply and erection of 7 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 155 mm, made of 3mm thick sheet along with base plate of size 260 X 260 X 16 mm , small door opening for junction box mounting with MCB & connector,cement,concrete of 1:3:6 including excavation, refilling and suitable size foundation bolts with template and all complete job as required. Single arm, 1500mm

Supplying and fixing 40/45 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supply of following sizes of 2/3/3.5 / 4 Core, 1.1KV grade aluminium conductor XLPE insulated PVC sheathed (Heavy duty) armoured cable conforming to relevant IS. 2.0Cx6 Sq.mm

Supply & making end termination with brass compression gland & bimettallic lugs for following size of FRLS insulated and sheathed aluminium conductor cable of 1.1KV grade as required. 2 X 6 sq. mm (25mm)

Shifting of existing equipments into new substation (Approximate Amount of Rs. 8,83,750.00)