Public Works Building And NH Department Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 20,42,528Document Cost
₹ 20,000Tender Fee
Refer Documents
Summary
Development Of Mahapurush Srimanta Sankardeva And Damodardeva Than At Pat
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_PWBNH_39835_1Bid Award Id
ViewTender No
CE/TB-VII/68/2024/5 Dated Guwahati the 7th Oct 2024Tender Authority
Public Works Building And NH Department ViewPurchaser Address
-Website
http://https://pwdbnh.assam.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upt`o 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
All kinds of soil
2004.51
-
-
Grassing with selection No. 1 Doob grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if
needed (the grass and good earth shall be paid for separately).
In rows 5 cm apart in both directions
4862
-
-
Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume
of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)
Holes 1.2 m dia and 1.2 m deep
200
-
-
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
877.23
-
-
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
1950.5
-
-
Supplying chemical emulsion in sealed containers including delivery as specified.
Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
219.65
-
-
Diluting and injecting chemical emulsion for pre-constructional anti-termite treatment (excluding the cost of chemical emulsion) :
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :
With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.
1098.25
-
-
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water)
SHRUBS PLANT
1000
-
-
Hedge Plant /Ground cover
2000
-
-
Pruning, trimming, shaping of trees /shrubs (ht 15 feet and above) i/c removal of cut materials upto 50mt. Lead, as per direction of officer in charge. T&P
shall be arranged by the contractor.
200
-
-
Providing and displaying of Araucaria cookie having ht. 75 cm to 90 cm, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 25 cm size of Earthen pot/Plastic pot & as per direction
of the officer-in-charge.
100
-
-
Providing and displaying of Areca Palm having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the
officer-in-charge.
200
-
-
Providing and displaying of Raphis palm having ht. 75 cm to 90 cm with 12 to 15 equal suckers, well developed, full of fresh & healthy leaves from bottom to top in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge.
200
-
-
Providing and Displaying Dahlia single in different colour with fresh & healthy foliage well developed with 6 to 8 half blooming buds in 20 cm Earthen Pot/
Plastic Pot and as per direction of the officer-in-charge.
200
-
-
Providing and Displaying Daisy well developed with fresh & healthy foliage in full bloom in 20 cm EarthenPot/Plastic Pot and as per direction of the officer-in-charge.
200
-
-
Providing and Displaying Marigold jaffri dwarf in differentcolour well developed with fresh & healthy foliagewith 12 to 15 flowers in full bloom specimen plant 23 to 30 cm ht. in 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
200
-
-
Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
200
-
-
Providing and Displaying Salvia ht. 45 to 60 cm multi branches stacking with bamboo stick specimen type with full bloom well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
200
-
-
Providing and Displaying Celosia well developed fresh & healthy 20 to 25 cm ht. (attractive) multi branching at blooming stage in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.
200
-
-
Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the
officer-in-charge.
200
-
-
Providing and Displaying Cyprus Golden Conical Shape 150 to 165 cm ht., with fresh and healthy Golden colour foliage in 35cm Cement Pot as per direction of the officer-in-charge.
40
-
-
Providing and Displaying Foxtail palm well developed with fresh & healthy foliage of ht. 210 to 240 cm in big 40 cm Cement Pot as per direction of the officer-in-charge.
40
-
-
Providing and Displaying Topiary of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht., in 35 cm Cement Tray /Cement Pot as per direction of the
officer-in-charge.
40
-
-
Providing and stacking of Clerodendrum inerme of ht. 20 cm to 30 cm multi branched in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the
officer-in-charge.
200
-
-
Providing and stacking of Chandni dwarf of height 15-20 cm., well branched in earthen pots of size 20 cm as per direction of the officer-in-charge. s per
direction of the officer-in-charge.
200
-
-
Providing and stacking of Hamelia patens of height 60-75 cm. with 6-8 branches in poly bags of size 25 cm as per direction of the officer-in-charge.
200
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from naturalsources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)
271.41
-
-
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)
373
-
-
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
743.98
-
-
Centring and shuttering including strutting,propping etc. and removal of form for
Foundations, footings, bases of columns etc. for mass concrete.
1009.14
-
-
Suspended floors, roots, landings, balcnies and access platform.
278.64
-
-
Lintels, beams, plinth bams, griders, bressumers and contilevers.
1817.49
-
-
Columns,Pillars, Piers, Abutments, Posts and Struts
944.67
-
-
Stairs,(excluding landings) except spiral-staircaces.
57.99
-
-
Extra for shuttering in circular work (20% of respective
centering and shuttering items)
423.77
-
-
Weather shade,Chajjas, corbels etc. including edges
2.51
-
-
Thermo-Mechanically Treated bars of grade Fe-500D or more.
68656.26
-
-
Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
All works upto plinth level
Concrete of M25 grade with minimum cement
content of 330 kg /cum
454.71
-
-
All works above plinth level upto floor V level
Concrete of M25 grade with minimum cement
content of 330 kg /cum
249.63
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
Cement mortar 1:6 (1 cement : 6 coarse sand)
251.9
-
-
ABOVE PLINTH BRICKWORK - HALF
2193.22
-
-
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade
complete.
121.76
-
-
Stone tile work for wall lining upto 10 M height with special adhesive over 12 mm thk. Bed of cement mortar 1:3 (1cement:3coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade.
8 mm thick (mirror polished and machine cut edge)
Granite stone of any colour & shade
824.16
-
-
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for seperately).
Sal wood
8.87
-
-
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:
35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
65.14
-
-
Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):
Rectangular or square.
7.22
-
-
Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edge
63.26
-
-
Providing & fixing M.S. Grills of required pattern in frames of winows etc. With MS flats, square or roun bers etc. Including priming coat with approved steel primer all complete. Fixed to steel windows by welding
4250.55
-
-
Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
14
-
-
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :250x10 mm
77
-
-
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
21
-
-
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary
accessories and screws etc. complete.
36
-
-
Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete.
14
-
-
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
100 mm
75
-
-
Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap betwen frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-charge. (Single/double glass panes, ire mesh and silicon sealent shall be paid saperately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.
Note : For uPVC frame & sash extruded profiles minus 5% tolerance in dimension i.e. In depth & width o profile shall be acceptable. Two track two panels sliding window made of (big series) frame 67x50 mm & sash 46x62 mm both having wall thickness o 2.30 ± 0.2 mm and single glazed bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm)
32.71
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
11752.15
-
-
Hot finished welded type tubes
48872.15
-
-
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing
with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge,
(for payment purpose only weight of stainless steel members
shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
2835
-
-
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade
complete.
177.02
-
-
Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks.
1635.76
-
-
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
40 mm thick with 20 mm nominal size stone aggregate
1199.36
-
-
40 mm thick marble chips flooring rubbed and polished to granolithic finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top layer 6mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 1 mm to 4 mm nominal size, laid in cement
marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume, including cement slurry etc. complete :
Light shade pigment with white cement
224.77
-
-
40 mm thick marble chips flooring, rubbed and polished to granolithic finish, under layer 31 mm thick cement concrete 1:2:4 (1cement:2coarse sand:4 graded stone aggregate 12.5 mm nominal size) and top layer 12 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 7 mm to 10mm nominal size, laid in cement marble powder mix 3:1 (3 cement:1 marble powder) by weight in proportion 2:3 (2 cement marble powder mix 3 marble chips) by volume, including cement slurry etc. complete.
Light shade pigment with white cement
2494
-
-
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.
98.84
-
-
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement:4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including
grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
Double charge vitrified tile polished finish of size
Size of Tile 600 x 600 mm
990.26
-
-
Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigments etc. complete.
88.89
-
-
Grouting the joints of flooring tiles having joints of 3 mm width, using
epoxy grout mix of 0.70 kg of organic coated filler of desired shade
(0.10 kg of hardener and 0.20 kg of resin per kg), including filling /
grouting and finishing complete as per direction of Engineer-in-charge.
Size of Tile 600x600 mm
836.84
-
-
Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :
Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
1407.34
-
-
Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting
to size and shape wherever required.
0.63 mm thick with zinc coating not less than 275 gm/ m²
1576.14
-
-
Extra for straight cutting in C.G.S. sheet roofing for making opening of area exceeding 40 sq. decimeter for chimney stacks, sky light etc.:
0.63 mm thick
480
-
-
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power press ed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval,
including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
12.5 mm thick tapered edge gypsum moisture resistant board
547.26
-
-
12mm cement plaster of mix :
1:6 (1 cement: 6 fine sand)
2175.81
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix :
1:6 (1 cement: 6 fine sand)
2376.97
-
-
12 mm cement plaster finished with a floating coat of neat cement of
mix : 1:3 (1 cement: 3 fine sand)
330.32
-
-
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :
Two or more coats applied on walls @ 1.25 ltr/10 sqm
over and including one coat of Special primer applied @
0.75 ltr /10 sqm
6295.81
-
-
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :
Two or more coats on new work over an under coat of
suitable shade with ordinary paint of approved brand and
manufacture
6206.77
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
6206.77
-
-
Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.
Two or more coats on new work
6206.77
-
-
With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)
408.33
-
-
With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat)
1334.09
-
-
Painting on G.S. Sheet with synthetic enamel paint of approved brand and manufactuer of required colour to give an even shade:
New work(two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.
1752.47
-
-
Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. Metres and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-charge. With cement mortar 1:4 (1cement:4coarse sand)
1708.54
-
-
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller
including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.
2305
-
-
Laying water bound macadam sub-base with brick aggregate and binding material, earth etc. including screening, sorting and spreading to template and consolidation with light power road-roller etc. complete.(payment for brick aggregate and moorum etc. to be made separately)
Over burnt (Jhama) brick aggregate 120 mm to 40 mm
345.75
-
-
Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved
by Engineer-in-charge).
78.66
-
-
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge
With material conforming to Grade-III (size range 26.5 mm to 0.075 mm ) having CBR Value-20
345.75
-
-
Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diametre and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but incluing the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap). 300 mm dia piles
734
-
-
Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.
Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing.
Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge.
Single pile above 50 tonne and upto 100 tonne Safe capacity
Initial test (Test Load 2.5 times the Safe capacity)
2
-
-
Routine test (Test Load 1.5 times the Safe capacity)
2
-
-
Epoxy injection grout in concrete/RCC work of approved make
1025
-
-
MURAL MOLDING
771.52
-
-
NSR2: Supply and installation of outdoor bench with planter, sitting capacity 2 seater material wooden bench type without back size 5 ft design modern usage/application outdoor Arm rest without arm rest appearance modern brand eazy Fab shape rectangular colour brown features water resistance (20 nos. quantity)
307740
-
-
Demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineerin-charge.
50
-
-
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.
Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
20
-
-
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
15
-
-
Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineerin-charge.
15
-
-
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.
In cement mortar
20
-
-
Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured):
From brick work in cement mortar
1
-
-
Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :
Of area 3 sq. metres and below
40
-
-
Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead :
Of sectional area 40 square centimetres and above
25
-
-
Extra for dismantling trusses, rafters, purlins etc. of wood work for every additional span of one metre or part thereof beyond 10 metres :
Of sectional area 40 square centimetres and above
50
-
-
Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in:
Channels, angles, tees and flat
100
-
-
Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious
water proofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge.
1000
-
-
Providing and applying crystalline mortar by mixing in the ratio of 4.5 : 1 (4.5 parts crystalline mortar : 1 part water) for the treatment of faulty construction joints, cracks, tie rod holes and spalled & honeycombed surface of RCC underground structures like basement, water tanks, bridge deck etc. to ensure water tightness. The crystallie mortar shall conform to the EN 1504-3 having compressive strength Class R4 ?45 MPa and adhesive bond strength Class R3 ?1.5 MPa. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.
For sealing cracks and faulty construction joints, routed out/making U-shape groove size 25x25mm and then primed the area with integral crystalline slurry @0.05kg/ running metre and while the surface is tacky filled the groove upto surface with crystalline mortar @1.50kg/ running metre. Once crystalline mortar is touch dry then finally applied two coats of integral crystalline slurry @0.05kg/running metre per coat.
100
-
-
Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.
200
-
-
Applying breathable, non-reactive, antifungal, and water repellant Silane/Siloxane chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-In-charge (The rate is inclusive of all materials & labours involved except scaffolding).
200
-
-
Providing and applying antifungal wash treatment using 3% solution of sodium pentachlorophenate, of reputed brand and manufacturer, on cleaned sand stone surface at desired locations as per direction of Engineer-in-charge (The rate is inclusive of all materials & labours involved except scaffolding).
200
-
-
Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured.
200
-
-
Grading roof for water proofing treatment with
Cement mortar 1:4 (1cement : 4 coarse sand)
20
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
26.28.1 75mm average thickness
100
-
-
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge
Bars above 12 mm diameter
196.8
-
-
Drilling suitable holes in reinforced or plain cement concrete with power driven drill machine to a minimum depth of 100mm upto 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-In-Charge.Upto and including 12mm dia
40
-
-
Grouting the joints of flooring tiles having joints of 3 mm width, using
epoxy grout mix of 0.70 kg of organic coated filler of desired shade
(0.10 kg of hardener and 0.20 kg of resin per kg), including filling /
grouting and finishing complete as per direction of Engineer-in-charge.
Size of Tile 600x600 mm
1005.6
-
-
Grouting the joints of flooring tiles having joints of 3 mm width, using
epoxy grout mix of 0.70 kg of organic coated filler of desired shade
(0.10 kg of hardener and 0.20 kg of resin per kg), including filling /
grouting and finishing complete as per direction of Engineer-in-charge.
Size of Tile 600x600 mm
10
-
-
Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastomeric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :
127
-
-
Supply,installation,testing and commissioning of UPVC drain piping complete with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell expanded polythene.
75
-
-
Supplying, installing, testing and commissioning of control cum transmission wiring of 2 core x 1.5 sqmm copper FRLSH, XLPE insulated cable in suitable GI conduits accessories between indoor and outdoor units. Necessary securing of conduit shall be made by contractor. After completion of work wall and floor shall be repaired and brought to its original finish. The rate will also include cost of laying of GI conduit between indoor and outdoor units.
50
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.
25 mm nominal dia Pipes
50
-
-
32 mm nominal dia Pipes
40
-
-
80 mm nominal dia Pipes
40
-
-
100 mm nominal dia Pipes
30
-
-
Providing and filling sand of grading zone V or coarser grade alround the GI pipes in external work.
32mm dia nominal bore
50
-
-
32mm dia nominal bore
40
-
-
80mm dia nominal bore
40
-
-
100mm dia nominal bore
30
-
-
Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :
with common burnt clay F.P.S.(non module) brick of class designation 7.5
4
-
-
Constructing masonary chamber 90x90x100cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. Surface box 100mm top diameter , 160 mm bottom diameter and 180 mm deep ( inside ) with chained lid and RCC top slab 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement:5 fine sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design with F.P.S. bricks.
2
-
-
Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement
: 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :
With common burnt clay F.P.S.(non modular) bricks of
class designation 7.5
2
-
-
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :
80mm dia
4
-
-
100mm dia
2
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
25mm dia
4
-
-
32mm dia
8
-
-
Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts,nuts, rubber insertions etc. (The tail pieces if required will be paid separately) :
80mm nominal bore
2
-
-
32mm nominal bore
8
-
-
32mm nominal bore
4
-
-
Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc. And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil.
All kind of soil
Pipes, cables etc, exceeding 80mm dia but not exeeding 300 mm dia
60
-
-
Extra for Excavation trenches for pipes, cables etc. in all kind of soil for depth exceeding 1.5m but not exceding 3m (Rate is over corresponding basic item for depth up to 1.5m)
30
-
-
Earthwork in excavation by mechanical means ( Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50m.
All kind of soil
149.73
-
-
Supplying and laying of following size DWC SN8 pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 16098, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.
150 mm dia
40
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :
150 mm diameter
40
-
-
200 mm diameter
50
-
-
Constructing brick masonry manhole with 75 class designation bricks in cement mortar 1:4 (1 cement: 4 coarse sand) R.C.C. top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand: 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.
Inside size 90x80 cm and 45 cm deep including CI Cover with frame (light duty as per IS:12592) 455x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg and weight of frame 15 kg)
with common burnt clay F.P.S.(non module) brick of class designation 7.5
18
-
-
Extra for depth for manholes Size 90 x 80 cm with common burnt clay F.P.S.(non module) brick of class designation 7.5
1.2
-
-
Constructing Brick Masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top with FPS bricks class designation 75 in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of of neat cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design.
0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S:12592, total weight of cover and frame to be not less than 182Kg. fixed in cement concrete 1:2:4 mix (1cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete.(Excavation foot rests and 12mm thick cement plaster at the external surface shall be paid for separately)
with common burnt clay F.P.S.(non module) brick of class designation 7.5
8
-
-
Extra depth for circuler type manholes 0.91 m internal dia ( at bottom ) beyond 0.91m to 1.67 m . with common burnt clay F.P.S.(non module) brick of class designation 7.5
3.2
-
-
Constructing Brick Masonry circular type manhole 1.22 m internal dia at bottom and 0.56m dia at top with FPS bricks class designation 75 in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of of neat cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design.
1.68m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S:12592, total weight of cover and frame to be not less than 182Kg. fixed in cement concrete 1:2:4 mix (1cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete.(Excavation foot rests and 12mm thick cement plaster at the external surface shall be paid for separately)
with common burnt clay F.P.S.(non module) brick of class designation 7.5
4
-
-
Extra depth for circuler type manholes 1.22 m internal dia ( at bottom ) beyond 1.68m to 2.29 m . with common burnt clay F.P.S.(non module) brick of class designation 7.5
1.5
-
-
Constructing Brick Masonry circular type manhole 1.52 m internal dia at bottom and 0.56m dia at top with FPS bricks class designation 75 in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of of neat cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design.
2.30m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S:12592, total weight of cover and frame to be not less than 182Kg. fixed in cement concrete 1:2:4 mix (1cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete.(Excavation foot rests and 12mm thick cement plaster at the external surface shall be paid for separately)
with common burnt clay F.P.S.(non module) brick of class designation 7.5
1
-
-
Extra depth for circuler type manholes 1.52 m internal dia ( at bottom ) beyond 2.30m . with common burnt clay F.P.S.(non module) brick of class designation 7.5
0.6
-
-
12 mm cement plaster finished with a floating coat of neat cement of mix :
1:3 (1 cement: 3 fine sand)
173.03
-
-
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
10
-
-
Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on12mm dia steel bar conforming to IS :1786 having minimum cross section as 23mm x 25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protrude legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with dtand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification make to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) complete as per design.
60
-
-
Excavating trenches of required width for pipes, cables etc. Including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5M including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering, etc. And disposing of surplus excavated soil as directed within a lead of 50 m Hard/dense soil. All kind of soil
Pipes, cables etc, exceeding 80mm dia but not exeeding 300 mm dia
80
-
-
Extra for Excavation trenches for pipes, cables etc. in all kind of soil for depth exceeding 1.5m but not exceding 3m (Rate is over corresponding basic item for depth up to 1.5m)
50
-
-
Earthwork in excavation by mechanical means ( Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50m.
All kind of soil
143.22
-
-
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
250 mm dia
80
-
-
300 mm dia
55
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up haunches of RCC. pipes including bed concrete as per standard design :
250mm dia RCC Pipe
80
-
-
300mm dia RCC Pipe
55
-
-
Constructing Brick Masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top with FPS bricks class designation 75 in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of of neat cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design.
0.91m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S:12592, total weight of cover and frame to be not less than 182Kg. fixed in cement concrete 1:2:4 mix (1cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete.(Excavation foot rests and 12mm thick cement plaster at the external surface shall be paid for separately)
with common burnt clay F.P.S.(non module) brick of class designation 7.5
10
-
-
Extra depth for circuler type manholes 0.91 m internal dia ( at bottom ) beyond 0.91m to 1.67 m . with common burnt clay F.P.S.(non module) brick of class designation 7.5
15
-
-
Constructing Brick Masonry circular type manhole 1.22 m internal dia at bottom and 0.56m dia at top with FPS bricks class designation 75 in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of of neat cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design.
1.68m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S:12592, total weight of cover and frame to be not less than 182Kg. fixed in cement concrete 1:2:4 mix (1cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete.(Excavation foot rests and 12mm thick cement plaster at the external surface shall be paid for separately)
with common burnt clay F.P.S.(non module) brick of class designation 7.5
6
-
-
Extra depth for circuler type manholes 1.22 m internal dia ( at bottom ) beyond 1.68m to 2.29 m . with common burnt clay F.P.S.(non module) brick of class designation 7.5
1.2
-
-
Constructing Brick Masonry circular type manhole 1.52 m internal dia at bottom and 0.56m dia at top with FPS bricks class designation 75 in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of of neat cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design.
2.30m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S:12592, total weight of cover and frame to be not less than 182Kg. fixed in cement concrete 1:2:4 mix (1cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete.(Excavation foot rests and 12mm thick cement plaster at the external surface shall be paid for separately)
with common burnt clay F.P.S.(non module) brick of class designation 7.5
1
-
-
Extra depth for circuler type manholes 1.52 m internal dia ( at bottom ) beyond 2.30m . with common burnt clay F.P.S.(non module) brick of class designation 7.5
0.6
-
-
Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design :
with common burnt clay F.P.S.(non module) brick of class designation 7.5
25
-
-
12 mm cement plaster finished with a floating coat of neat cement of mix :
1:3 (1 cement: 3 fine sand)
186.15
-
-
Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on 12 mm dia steel bar conforming to IS :1786 having minimum cross section as 23mm x 25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protrude legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with dtand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification make to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) complete as per design.
60
-
-
Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :
For pipes 250 to 300 mm diameter
2
-
-
Providing, fixing, commissioing, testing and of open well submersible pump for each pump IP 58 protected electric enclosure comprising of 2 Nos. Electrical Driven Horizontal pumps with all accessories coupled to motor suitable for operation on 200-240 volts, 1 phase 2900 RPM. motor with SS 304 body all accessories such as NRVs, valves, common delivery header complete in all repsects.
Pumps shall be suitable for 200-240volts 1 phase 50 Hz A.C supply & shall be having the following specifications. Moc of pump -Impeller- CI, csing - CI , shaft- SS 410.
Delivery header including all GI pipes, CI valves, CI NRV, bourden type Pressure gauge & accessories complete. All accessories for running two pumps with dry running protection etc.
FOR DOMESTIC TRANSFER PUMP No. of Pumps: 2 (1 Working + 1 Stand by )
Capacity : 120 LPM
Head : 30m
2
-
-
FOR GARDEN IRRIGATION PUMP No. of Pumps: 2 (1 Working + 1 Stand by )
Capacity : 140 LPM
Head : 30m
2
-
-
Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersible motor for 415 volts, 3 phase, 50 cycles including MCC panel with level controllers, auto control, sequential change over facility with one proper working at low level & two proper working at high level with an audible alarm including all interconnectivity cables, with both pumps connected to common outlet header including valves, non return valves, lifting chains etc. complete in all respect SUBMERSIBLE UNDER GROUND FOR BOREWELL
No. of Pumps: 1 (1 Working )
Capacity : 160 LPM
Head : 60 m
2
-
-
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, up to 90 metre depth below ground level.
All Types of Soil
300mm dia
60
-
-
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.
All Types of Soil
300mm dia
15
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia
60
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia
60
-
-
Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.
20
-
-
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.
100
-
-
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:
200 mm dia
2
-
-
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.
200 mm clamp.
2
-
-
Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).
200 mm dia
2
-
-
Design, Installation testing & commisioning of Sewerage treatment plant in MBBR (MOOVING BED BIO REACTOR TECHNOLOGY) process electro Mech. work only, Tertiary treatment completely for Domestic Sewege capciaty 20 cum/day. Outlet Parameter should be match for using the water for Gardening & Flushing purpose. Bidder should include following items as specified below suitable for 20 cum/day STP. (Bidder Must visit the site before quote) Depth of Incomming sewer 3.5m to be consider.
Sewerage treatment plant 20 cum/day complete following above items.
2
-
-
Providing and fixing white vitreous china pedestal type water closet
(European type) with seat and lid, 10 litre low level white vitreous
china flushing cistern & C.P. flush bend with fittings & C.I. brackets,
40 mm flush bend, overflow arrangement with specials of standard
make and mosquito proof coupling of approved municipal design
complete, including painting of fittings and brackets, cutting and
making good the walls and floors wherever required :
W.C. pan with ISI marked white solid plastic seat and lid
16
-
-
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass
pillar taps, 32 mm C.P. brass waste of standard pattern, including
painting of fittings and brackets, cutting and making good the walls
wherever require:
White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
20
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as
per IS:13983 with C.I. brackets and stainless steel plug 40 mm,
including painting of fittings and brackets, cutting and making good
the walls wherever required :
Kitchen sink without drain board
470x420 mm bowl depth 178 mm
2
-
-
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
20
-
-
Providing and fixing P.V.C. flexible waste pipe for sink including P.V.C. waste fittings complete. Flexible pipe
40 mm dia
2
-
-
Providing and fixing mirror of superior glass (of approved quality) and
of required shape and size with plastic moulded frame of approved
make and shade with 6 mm thick hard board backing :
Rectangular shape 453x357 mm
20
-
-
Providing and fixing C.P. brass angle valve for wash basin and geyser points of approved quality conforming to IS:8931.
48
-
-
Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length
15 mm nominal bore
48
-
-
Providing and fixing toilet paper holder :
C.P. brass
20
-
-
Providing and fixing PTMT liquid soap container 109 mm wide, 125
mm high and 112 mm distance from wall of standard shape with
bracket of the same materials with snap fittings of approved quality
and colour, weighing not less than 105 gms.
18
-
-
Providing and fixing C.P. brass long body bib cock of approved quality
conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore
16
-
-
Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
2
-
-
Providing and Fixing chrome plated Sink Faucet with swinging casted spout wall mounting model with connecting legs and wall flanges for flow rate 2.5lps @ 45PSI complete in all respect.
2
-
-
Supply installation, testing and commissioning of water cooler with Inbuilt Aquagaurd RO purification + UV(50LPH) .Cooling capacity shall be 60 liter & 80 liter shall be storage capacity.Its should have 7 stages purification process,fully automatic,rectangular tank with Forced fin and tube condenser,Non-corrosive SS-304 outer body,Food-grade SS-304 stainless steel inner tank (18/8 or 18/10),PUF insulation,Reciprocating compressor with R22 Refrigerant.Water outlet temp is aprrox 17 deg c ,Operating power supply 230 + 10% V AC,50 Hz,1 PH,No of Cold water Faucet-2.Dimension (660W x 480DX1355H) .
2
-
-
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge
10
-
-
Providing and fixing 75 mm high, 50 mm deep and 18 mm thick stone slab table rubbed, edges rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.
White Agaria Marble Stone
11
-
-
Providing and Fixing of ABS health spary which can tolerate water pressure up to 6 bar flow pressure with metal hose and holder in Polished Chrome.
16
-
-
Providing and Fixing of SS Double coat Hook including cutting and making good the walls where required complete with all respect.
12
-
-
Providing and Fixing chrome plated 2 way bib cock with flow rate of 1.3 Lps @ 45 PSI complete in all respect.
20
-
-
Providing and Fixing straight /offset type Macfit single body push fit type WC pan connector with factory supplied spring loaded seal guard of McAlpine, UK with integral single mould sealing fins made of flexible EVA body, including bush/adaptor for use with C.I. Pipe as supplied with the pan connector (if required).
20
-
-
Providing and Fixing of SS 32mm dia & 600mm long Grab Bar complete, including cutting and making good the walls where required.
8
-
-
Providing, fixing & testing uPVC SWR pipes confirming to IS 13592 (Type B) alongwith all required fittings like tees, bends, crosses with or without access doors jointed with approved solvent cement as per manufacturer's recommendations, fixed to walls and ceilings with clamps complete including cutting and making good the floors and walls where required complete of outer diameter.
110 mm O.D.
114
-
-
Providing, fixing, jointing and testing in position the following uPVC pipes conforming to IS 4985 of 6 kg/sqcm pressure rating including all fittings, solvent weld joints, testing complete for drainage system cut to required length to be laid under floor including covering all around with cement concrete and making good the same complete as required.
For waste pipes 40mm OD (6 kg pressure)
61
-
-
50mm OD (6 kg pressure)
19
-
-
63mm OD (6 kg pressure)
40
-
-
Providing and Fixing 110x110 mm uPVC 'P' trap with Height riser/Saddle as required size ftting with seal 50 mm of self cleansing design floor/urinal trap without vent suspended with supporting clamp or in sunken portion including cutting and making good the walls and floors wherever required complete in all respects.
110 mm inlet & 110 mm outlet
25
-
-
Providing and Fixing uPVC floor drain of following size inlet and outlet including cutting and making good the walls and floors wherever required complete in all respects.
110 x63mm outlet
5
-
-
Providing and fixing 125 mm dia, 3 mm thick Stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete.
125mm dia.
28
-
-
Providing & fixing PVC clean out plug with suitable insert keys for opening in: brass cap, male threaded joint with threaded uPVC socket fixed to uPVC pipe joints as required complete in all respects.
110mm dia.
11
-
-
Providing and fixing uPVC rain water pipes of 6kg/cm2 conforming to IS: 4985 including all fittings with or without access i.e bends, junctions, cowls, offsets, etc., and jointing with solvent cement including cutting holes in walls and floors ,wherever required and making good the same, complete as directed by the Engineer-in-Charge.
110mm outer dia.
43
-
-
Making khurras 45x45 cm with average minimum thickness of 5 cm
cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone
aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400
micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse
sand) and a coat of neat cement, rounding the edges and making
and finishing the outlet complete.
12
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply, including all
CPVC plain & brass threaded fittings, including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings
with one step CPVC solvent cement and testing of joints complete
as per direction of Engineer in Charge.
Internal work-Exposed on wall
'20mm dia
45
-
-
25mm dia
90
-
-
32mm dia
69
-
-
40mm dia
68
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply, including all
CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps
at 1.00 m spacing. This includes jointing of pipes & fittings with one
step CPVC solvent cement and the cost of cutting chases and making
good the same including testing of joints complete as per direction
of Engineer in Charge.
Concealed work including cutting chases and making the walls etc
'15mm dia
134
-
-
20mm dia
152
-
-
25mm dia
80
-
-
32mm dia
25
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved
quality (screwed end) :
'20mm dia
4
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved
quality (screwed end) :
'32mm dia
6
-
-
40mm dia
24
-
-
Providing and placing on terrace (at all floor levels) polyethylene water
storage tank, IS : 12701 marked, with cover and suitable locking
arrangement and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank. For Per lit. capacity
3500
-
-
Excavating trenches of required width for pipes, cables etc including excavation for socket and dressing of sides ramming of bottoms depth upto 1.50 m including timbering, shuttering, centering etc. as required getting out the excavated soil and then returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil outside the site premises. a) All kind of soil
Pipes cables etc exceeding 80 mm dia but not exceeding 300 mm dia.
26.5
-
-
Providing, laying and jointing DWC HDPE Black pipes (SN-8) confirming to IS 16098 including testing of joints etc. complete as required.
150 mm dia
26.5
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse
sand : 10 graded stone aggregate 40 mm nominal size) all-round
S.W. pipes including bed concrete as per standard design :
150 mm OD (For DWC HDPE Pipe)
26.5
-
-
Constructing brick masonry manhole in cement mortar 1:4 ( 1
cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1
cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20
mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4
coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal
size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement
: 3 coarse sand) finished with floating coat of neat cement and
making channels in cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 20 mm nominal size) finished with
a floating coat of neat cement complete as per standard design :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
8
-
-
Extra for depth for manholes Size 90x80 cm
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
0.4
-
-
Providing and fixing square-mouth S.W. gully trap class SP-1
complete with C.I. grating brick masonry chamber with water tight
C.I. cover with frame of 300 x300 mm size (inside) the weight of
cover to be not less than 4.50 kg and frame to be not less than 2.70
kg as per standard design:
180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
8
-
-
Making connection of drain or sewer line with existing manhole
including breaking into and making good the walls, floors with cement
concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) cement plastered on both sides
with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a
floating coat of neat cement and making necessary channels for
the drain etc. complete :
For pipes 100 to 250 mm diameter
8
-
-
Excavating trenches of required width for pipes, cables etc including excavation for socket and dressing of sides ramming of bottoms depth upto 1.50 m including timbering, shuttering, centering etc. as required getting out the excavated soil and then returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil outside the site premises. a) All kind of soil
Pipes cables etc exceeding 80 mm dia but not exceeding 300 mm dia.
26.5
-
-
Providing, laying and jointing DWC HDPE Black pipes (SN-4) confirming to IS 16098 including testing of joints etc. complete as required.
150 mm dia
26.5
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse
sand : 10 graded stone aggregate 40 mm nominal size) all-round
S.W. pipes including bed concrete as per standard design :
150 mm OD (For DWC HDPE Pipe)
26.5
-
-
Constructing brick masonry road gully chamber with bricks of class designation 75 in cement mortar 1:5 (1cement : 5 coarse sand), inside cement plastering 12mm thick with cement mortar1:3 (1 cement: 3 coarse-sand) finished with a floating coat of neat cement, outside plaster 12 mm thick in cement mortar 1:3(1 cement : 3 coarse sand) I00mm thick PCC in foundation M-10 grade,foundation rcc grade M-25 including rainforcement 60Kg/cum. with rcc perforated horizontal grating wilh frame fixed in150mm thick cement concrete grade M-25 including excavation, backfilling and disposal of surplus earth as directed by engineer in charge as per standard design complete with all respect incuding shuttering.
600 x 600 x 660 Av Depth
8
-
-
Making connection of drain or sewer line with existing manhole
including breaking into and making good the walls, floors with cement
concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) cement plastered on both sides
with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a
floating coat of neat cement and making necessary channels for
the drain etc. complete :
For pipes 100 to 250 mm diameter
8
-
-
Providing and fixing ball valve (brass) of approved quality, High or low
pressure, with plastic floats complete :
20 mm dia
2
-
-
9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold water supply including all CPVC
plain & brass threaded fittings This includes jointing of pipes & fittings
with one step CPVC solvent cement, trenching, refilling & testing of
joints complete as per direction of Engineer in Charge.
25 mm dia nominal bore
6
-
-
32 mm dia nominal bore
47.31
-
-
Supply, Insttalation, Testing & commisioning of water float valve for OHT as per requirment / Drawing.
32 mm dia
7
-
-
Making connection of water supply distribution branch with External water supply main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :
20 to 50 mm nominal bore
9
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit with modular switch modular plate suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.as required.
Group C
122
-
-
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.
Group C
182
-
-
Wiring for power plug points with 2 x 4 sq.mm. FRLS PVC insulated, Cu. Conductor, single core cable in surface/ recessed steel conduit along with 1 No. 4 sq.mm. FRLS PVC insulated copper conductor single core cable for loop earthing as required.
860
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed Steel conduit as required
2 x 1.5 sq.mm. + 1 x 1.5 sq.mm. earth wire.
1790
-
-
2 x 2.5 sq.mm. + 1 x 2.5 sq.mm. earth wire.
170
-
-
4 x 2.5 sq.mm. + 2 x 2.5 sq.mm. earth wire.
570
-
-
2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire
620
-
-
2x10 sq. mm + 1x6 sq. mm earth wire
300
-
-
2x16 sq. mm + 1x6 sq. mm earth wire
70
-
-
4 X 6 sq. mm + 2 X 6 sq. mm earth wire
20
-
-
4 X 10 sq. mm + 2 X 6 sq. mm earth wire
75
-
-
4 X 16 sq. mm + 2 X 6 sq. mm earth wire
80
-
-
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
45
-
-
Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
5
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
49
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
13
-
-
Supplying and fixing brass batten/ angle holder including connection etc. as required.
40
-
-
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
40
-
-
Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
45
-
-
Supply, installation, testing & commissioning of 10W surface mounted LED downlighter fitting complete, as required.
8
-
-
Supply, installation, testing & commissioning of 20W Track light. complete, as required.
49
-
-
Supply, installation, testing & commissioning of Recess mounted LED downlighter fitting, complete as required.
20
-
-
Supply, installation, testing & commissioning of 20W surface / wall mounted LED batten light-4ft. complete, as required.
6
-
-
Supply, installation, testing & commissioning of 20W Hanging Light. complete, as required.
57
-
-
Supply, installation, testing & commissioning of LED Bulb 10W 800lm E27 6500K A67 ,colour temperature 5700 K having efficacy not less than 80 lm/W, CRI ≥ 70 ,THD ≤ 10%, complete as required or approved Equivalent.
103
-
-
Supplying and fixing of 225 mm sweep plastic body Fresh air fan with all accessories suitable for operation single phase 230 volt 50 cycle per second per sec. AC supply etc. as required. in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning earthing etc. as required.
16
-
-
Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
45
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door
6
-
-
8 way, Double door
8
-
-
12 way, Double door
3
-
-
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
4 Way (4+12), Double Door
6 Way (4+18), Double Door
1
-
-
8 Way (4+24), Double Door
3
-
-
Supplying and fixing Cable End Box (Loose Wire Box) suitable for following single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required.
For 6 way, Double door SPN MCBDB
2
-
-
For 8 way, Double door SPN MCBDB
8
-
-
For 14 way, Double door SPN MCBDB
3
-
-
Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface / recess, complete with testing and commissioning etc.as required.
For 4 way, Double door TPN MCBDB
For 6 way, Double door TPN MCBDB
1
-
-
For 8 way, Double door TPN MCBDB
3
-
-
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Single pole
192
-
-
Supplying and fixing following rating, double pole, 240 volts, MCB complete with connections, testing and commissioning etc. as required.
25 Amp DP MCB
24
-
-
Supplying and fixing of following rating, 240/415 volts, "C" curve, four pole miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
25 Amp FP MCB
7
-
-
40 Amp FP MCB
2
-
-
Supplying and fixing of following rating double pole (Single phase and neutral) 240 volts, residual current circuit breaker (RCCB), having a current sensivity current 100 miliampere in the existing MCB DB complete with connections, testing & commissioning etc. as required.
25 Amps
23
-
-
Supplying and fixing of following rating, 240/415 volts, "C" curve, three pole miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
25 Amp TP MCB
2
-
-
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
20
-
-
Design, Manufacturing, Supply, Installation, Testing & Commissioning of cubicle type totally enclosed free standing / Wall mounted type moisture, dust and vermin proof compartmentlized Floor Distribution Panel made out of 2.0 mm thick of Main members & front cover 1.6 mm thick CRCA sheet complete with internal wiring with suitable size wires / cable, interconnection, painting complete as per specification & drawing. All the Multi Function Meter / KWH Meter shall be with RS 485 port / SCADA or BMS Connectivity. The MCCB rating up to 250A shall have thermal megnatic based adjustable over current, short circuit protection and above 250A MCCB shall have microprocessor based adjustable over current, short circuit, earth fault protection.
All Main Distribution board / Sub Distribution board / Meter boards which are located inside various blocks shall be partially Type Tested assemblies (PTTA) as per conforming to IEC-61439-1
The Moulded Case Circuit Breaker shall have a minimum fault breaking capacity (Ics) of not less than 35 KA & 25KA RMS for one second at 415 volts for MDB / SDB respectively. MCCB‘s above 63A should be provided with Copper & procader terminals. Incomer of Meter Board shall have a minimum short circuit breaking capacity (Ics) of 25KA for one second at 415volt.
BUILDING FEEDER PILLAR-1 (OUTDOOR TYPE)
INCOMING
1 No. 100 Amp FP Moulded Case Circuit Breaker.
1 Set of phase indicating lamps with MCB.
1 Set of ON/OFF indicating lamps with MCB.
1 No. Digital MFM with CT's.
BUSBAR
150 Amp TPN aluminium busbar with coloured heat shrinkable sleeve. OUTGOING
6 Nos. 40 / 63 Amp TPN Miniature Circuit Breaker.
6 Nos. 25 / 40 Amp DP Miniature Circuit Breaker.
Panel described as above
2
-
-
BUILDING FEEDER PILLAR-2 (OUTDOOR TYPE)
INCOMING
1 No. 100 Amp FP Moulded Case Circuit Breaker.
1 Set of phase indicating lamps with MCB.
1 Set of ON/OFF indicating lamps with MCB.
1 No. Digital MFM with CT's.
BUSBAR
150 Amp TPN aluminium busbar with coloured heat shrinkable sleeve. OUTGOING
9 Nos. 40 / 63 Amp TPN Miniature Circuit Breaker.
6 Nos. 25 / 40 Amp DP Miniature Circuit Breaker.
Panel described as above
2
-
-
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
20
-
-
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
8
-
-
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
120
-
-
Providing and fixing 32 mm X 6 mm copper strip on surface or in recess for connections etc. as required.
75
-
-
Providing and fixing 32 mm X 6 mm G.I. strip on surface or in recess for connections etc. as required.
70
-
-
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
425
-
-
Supplying following 1.1kV grade, heavy duty XLPE insulated PVC Sheathed Aluminum Conductor FRLS type armoured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete etc. as required.
3.5 core, 185 sq.mm.
50
-
-
3.5 core, 95 sq.mm.
300
-
-
3.5 core, 70 sq.mm.
150
-
-
3.5 core, 35 sq.mm.
60
-
-
4 core, 25 sq.mm.
300
-
-
4 core, 16 sq.mm.
375
-
-
4 core, 6 sq.mm.
375
-
-
4 core, 4 sq.mm.
650
-
-
3 core, 10 sq.mm.
60
-
-
2 core, 10 sq.mm.
800
-
-
2 core, 6 sq.mm.
530
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
Upto 35 sq. mm
1980
-
-
Above 35 sq. mm and upto 95 sq. mm
292.5
-
-
Above 95 sq. mm and upto 185 sq. mm
32.5
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.
Upto 35 sq. mm
720
-
-
Above 35 sq. mm and upto 95 sq. mm
101.25
-
-
Above 95 sq. mm and upto 185 sq. mm
11.25
-
-
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.
Upto 35 sq. mm (clamped with cable tie)
1600
-
-
Above 95 sq. mm and upto 185 sq. mm (clamped with cable tie)
225
-
-
Above 185 sq. mm and upto 400 sq. mm (clamped with cable tie)
305
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.
3½ X 185 sq. mm (57mm)
8
-
-
3½ X 95 sq. mm (45mm)
10
-
-
3½ X 70 sq. mm (38mm)
6
-
-
3½ X 35 sq. mm (32mm)
4
-
-
4 X 25 sq. mm (28mm)
10
-
-
4 X 16 sq. mm (28mm)
12
-
-
3 X 10 / 6 sq. mm
15
-
-
2 X 10 / 6 sq. mm
48
-
-
Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 63 mm dia
145
-
-
120 mm dia
125
-
-
200 mm dia
20
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.
300 mm width x 50 mm depth x 1.6 mm thickness
25
-
-
600 mm width X 50 mm depth X 2.0 mm thickness
25
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness
6
-
-
600 mm width X 50 mm depth X 2.0 mm thickness
6
-
-
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm width x 50 mm depth x 1.6 mm thickness
2
-
-
600 mm width X 50 mm depth X 2.0 mm thickness
2
-
-
Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line :
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
6
-
-
Inside dimensions 600x 850 mm and 45 cm deep for pipe line with three or more inlets :
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
7
-
-
Extra for depth beyond 45 cm of brick masonry chamber For 455x610 mm size
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
6
-
-
Extra for depth beyond 45 cm of brick masonry chamber For 600x850 mm size
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
7
-
-
Supply, Installation, Testing and Commissioning of on grid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:-
a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years.
b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency.
c) Data Monitoring System complete with accessories.
d) Fixing of Array junction box & Main junction box with IP 65 protection and
termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required.
e) Lightning and surge voltage protection.
f) Connections & Interconnections by supplying & fixing required size XLPE
insulated copper conductor 1.1 kV grade armoured power and control cables
between solar modules, main power cable to grid supply PCU unit along with
supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.
20
-
-
Supply, Installation, Testing and Commissioning of Battery Bank for the above mentioned system for minimum 30 min backup time.
20
-
-
Supply, installation, testing and commissioning of 5 MP Dome camera ,ONVIF profile S,G & T. UL , CE , FCC Certified ,1/2.7” Progressive Scan CMOS , 3.6 mm fixed lens , Quad stream Each stram support H.265 compression simultaneously ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : 1 / 5s ~ 1 / 100,000 s , WDR , Compression : H.265/H.265+/H.264/H.264+ .SD card support upto 256GB , frame rate : Main stream should support 25 fps@5MP ,Edge analytics : Customer Flow staistics, Cross Count,Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection Regional population statistics, SOD-Stationaary Object Detection , In built IR LED , IR Distance upto 30 meters , IP 66 ,POE.
4
-
-
Supply, installation, testing and commissioning of 5 MP Bullet camera , ONVIF profile S ,G & T . UL , CE , FCC Certified ,1/2.7” Progressive Scan CMOS , 3.6 mm fixed lens , Quad stream support ,min illumination : Color 0.05lux @ F1.2(AGC ON) ; B/W 0 lux @ IR ON , Shutter speed : Shutter speed : 1 / 5s ~ 1 / 100,000 s ,WDR , Compression : H.265/H.265+/H.264/H.264+ .SD card support up to 256GB , frame rate : Main stream should support 25 fps@5MP , Edge analytics : Customer Flow staistics,Cross Count Heat Map, Human & Vehicle Detection, Pedestrian Intrusion Detection & Line cross Detection. Queue length detection, Regional population statistics, SOD-Stationaary Object Detection. , In built IR LED , IR Distance upto 30 meters , IP 66 , POE.
12
-
-
Supply, installation, testing and commissioning of 16 channel NVR , ONVIF compliant , recording bandwidth 640 Mbps , output interface 1 HDMI (up to 4K), 1 VGA , Alarm in/out : 16ch in / 4ch out , 1 X RJ45 ethernet , iOS smartphone support , 8 HDD support , each HDD slot support upto 8 TB HDD , 1x3.0 USB for backup /upgrade , 2x 2.0 USB for mouse .Edge analytics of poposed cameras must be integrated with NVR . Artificial Intelligence Support having face recognition with compatible deep learning supported cameras, AI-Face registered quantity upto 10,000 ,A.I maximum captured quantity 200,000. UL,CE,FCC certified.
2
-
-
Supply, Installation, Testing & Commissioning of 8TB Surviellance Hard Disk.
6
-
-
Supply, Installation, Testing and Commissiong of Workstation PC: Intel(R) Core(TM) 8th gen i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 16GB (2x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest.
2
-
-
Supply, Installation, Testing and Commissioning of Full HD 55" LED Professional Display Panel.
2
-
-
Supply, Installation, Testing & Commissioning of Armoured 06 Core Singlemode (OS2) 9/125 Fiber Cable, ITU G.652.D, G.657A1, Outdoor ECCS Armored Fiber Cable with PBT Loose Tube Filled With Thixotropic Jelly, Uni-Tube, Glass Yarn, Water Swellable Tape Under Armor, UV-HDPE Jacket.
570
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed Steel conduit as required
2 x 1.5 sq.mm. + 1 x 1.5 sq.mm. earth wire.
175
-
-
Supply, Installation, Testing & Commissioning of CAT 6 UTP Universal (both tool & toolless) information outlet (I/O) in accordance with ANSI TIA 568 C.2, IEC 60603-7-4 2nd Edition, ISO/IEC TR 11801-9901-2014, ROHS Compliant. The I/O should have minimu 750 mating cycle and 200 insertion cycle and UL approved,for Data, Voice, Wifi & CCTV at user end.
16
-
-
Supply, Installation, Testing & Commissioning of loaded 24 port CAT 6 UTP, Transparent shutter jack panel, 1U height, UL-94V-0, Black with cable support bar, clear label marks and earthing plug for CAT6 cable termination at rack end.
2
-
-
Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 1 Mtr for rack side switch to jack panel connectivity.
16
-
-
Supply, Installation, Testing & Commissioning of CAT 6 UTP, LSZH Patch Cord as per ANSI/TIA/EIA 568C.2 and UL 94-V-0, ROHS Compliant, patch cord 2 Mtr for rack side switch to end user connectivity.
16
-
-
Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate, British Style with Shutter, 2 Plate system clear finish with transparent labelling, ABS-UL94-V2, ROHS Compliant, in accorandce with standards like ANSI/TIA-568-C.2, ISO/IEC 11801:2002 AMMD.2:2010, YD/T 926.3-2009 & ISO/IEC 60603-7 white for I/O fixing at user side.
16
-
-
Supply, Installation, Testing & Commissioning of 9 U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.
2
-
-
Supply, Installation, Testing & Commissioning of 6U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.
2
-
-
Supply, Installation, Testing & Commissioning of of 22 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with 2 x 10G SFP+ uplink ports. Should support for Stacking/VC with stacking cable with stacking bandwidth of maximum 40 Gbps as and when required. Should support min 2GB internal DRAM, 2GB internal Flash memory, 16K MAC address. Should have Static Routing , Neighbor discovery, system logging, Telnet, SSH, SNMP, Network Time Protocol (NTP), Domain Name System (DNS) and IPv6 features from day 1 and should support OSPF, VRRP, OSPFv3 and PIM.
2
-
-
Supply, Installation, Testing & Commissioning of Pure IP at core server Based voice solution with 04 Port Voicemail ,04 Port FXS ,04 Port FXO ,1 PRI Trunk lines (30 Ch) Circuit with CLIP Facility ,35 IP users License ,01 Nos. IP Operator Console, 75 Party Conference ,Speed Dial, Music on Hold , Internal/ External ring difference ,Call Barring, Call Pickup, TEC should be with GR Number, - Should Support Redundant server in active-Active mode.
2
-
-
Supply, Installation, Testing & Commissioning of Type 2 IP Phone with 4 Voip accounts, 4 line keys, 3.5-inch (480x320) Colour Screen display with backlight, GigE, colour displays for 6 DSS keys, IPV6, 2 x Gigabit Ethernet , PoE.
4
-
-
Supply ,Installation ,Testing & Commissioning of Electromagnetic Lock 600 lbs, Single leaf, LED Status Display, Approved Makes : Assa Abloy / Ablesco / Impulse / BEL
2
-
-
Supply and erection of 3 Mtr height MS Decorative pole with openable door/window & the following size made with 3mm thick hot dip galvanised sheet with 220mm x 220mm x12mm thick base plate welded at bottom & making cement concrete ( 1 Cement : 2 coarse sand : 4 stone) CC foundation of size 500mm x 500mm x 750mm (LxWxD) with suitable reinforcement cement including supplying fixing of 4 Nos 16mm dia 700mm long J type foundation bolt with anchor plates & nuts HDPE/HARD 65mm dia pipe for cable entry and supplying and fixing of 1.00 Mtr long single arm suitable bracket for installation of fitting & supplying and fixing 1 Nos 16 Amp C serice MCB i/c suitable size 3 Nos aluminium bus bar strip, 6mm thick bakelite sheet, din bar with accessories etc. complete as required.
35
-
-
Supply, Installation, Testing & commissioning of IP65 8W LED Bollard with dark grey polyester coated rust proof Die cast Aluminium housing, with symmetrical dual optics and PC diffuser The luminaire shall have initial system lumen of 400lm with System efficacy of 50Lumen/W. The LED shall have a CCT of 3000K with LEDs shall be LM80 Compliant with TM21 report for life of 25000 hrs at 35 Deg C. and CRI 80 with beam angle of 360°.The Fixture shall have IP65 potted driver with THD25%, PF0.9, with operating volatge range of 180-270V. The fixture shall comply with IS 10322 part 5/Sec 1 1987 and LM79 LM80 reports are tested and certified by NABL accredited Lab. (for landscaped area)
72
-
-
Supply, Receiving, Unloading, Shifting, Installation, Testing & commissioning of 35W LED Post top luminaire consisting of a high-pressure powder coated die-cast aluminium housing, a canopy made of plastamid and a UV resistant high impact polycarbonate protector. The luminaire emits a pleasant, glare-free light due to the highly efficient white reflector (symmetrical light distribution). The complete luminaire is sealed to IP 66 & Impact resistance of IK08. Electronic temperature monitoring prevents overheating of LEDs and power supply within the LED compartment (ThermiX®). It is designed for LED light sources of 25W having a neutral white light. Surge protection of 10kV.
100
-
-
Supply, Installation, Testing & Commissioning of Environmental friendly, new generation, energy saving, 20 watt decorative flood light mini LED as light source. The fixture shall comply with IS 10322 part 5/Sec 1 1987 and LM79 LM80 reports are tested and certified by NABL accredited Lab. (for landscaped area)
45
-
-
Supply, Installation, Testing & Commissioning of Natural white (3000/4000K/6500K Luminaire) Hard 10W/Mtr. LED Strip having light output min 1000 Lumens per mtr and system efficiancy better than 100 LPW, Low Voltage 12V DC system, with Thermo-conductive adhesive 3M base for safe installation on almost any flat surface for IP-67 protection, CE & ROHS complaince with indoor/ Outdoor driver fixed on Surface of wall complete etc. as required. (for building outer wall façade & steps)
25
-
-
Supply, installation, testing & commissioning of Solar Light. complete, as required.
19
-
-
Design, Manufacturing, Supply, Receiving, Unloading, Shifting, installation, testing & commissioning of cubicle type totally enclosed free standing type moisture, dust, vermin & weather proof Floor Distribution Panel made out of 2.0 mm thick & front cover 1.6 mm thick CRCA sheet complete with following equipments, including digital ammeter with inbuilt ammeter selector switch, digital voltmeter with inbuilt voltmeter selector switch, indicating lamps, CT's, internal wiring with suitable size wires / cable, MS Angle stand for installation, RCC foundation, interconnection, painting complete as per specification & drawing. INCOMING
1 No. 40 Amp FP Moulded Case Circuit Breaker.
1 No. 0 to 500 Volt digital voltmeter with inbuilt selector switch.
1 No. 40 Amp digital ammeter with inbuilt selector switch and CT's.
1 Set of phase indicating lamps with Single Pole MCB.
1 Set of ON / OFF indicating lamps with Single Pole MCB.
BUS BARS
100 Amp TPN aluminium busbar. OUTGOING
3 Nos. 25 Amp FP MCB, 10 KA breaking capacity.
1 Set 24 Hrs TSQ Timer
1 Set 32 Amp, TP Contactor & A/M switch and Push Button.
12 Nos. 16 Amp TP MCB, 10 KA breaking capacity.
Panel described as above
2
-
-
Supplying, Installation, Testing & Commissioning of indoor type floor mounted metal clad, 11 KV VCB panel with single VCB, totally inclosed & fully interlocked, horizontal drawout, horizontal isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, manually charged and manually closing breaker suitable for use on 11 KV, 3 phase, 50 Hz A.C. supply with short circuit fault level of 350 MVA, complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated but encapsulated copper bus bars of 600 Amp capacity, breaker featured with mechanical ON/OFF indicator with hand trip device.
Spring release coil, shunt trip coil and auxiliary switch of 4 NO + 4 NC and equipped with following switchgears and accessories i/c connections for 3 x 185 sq.mm. XLPE 11 KV cable (cable entry from bottom), end termination with heat shrinkable jointing material etc. as required. (Note - Cost of end termination not included in this item).
a) Incoming cum Outgoing - 1 No, 630 Amp, VCB
b) 1 No.- 11 KV / 110 Volt PT class 0.5 accuracy and 100 VA burden with 1 No. voltmeter (0-12 KV), digital type, selector switch for voltmeter and protection MCB for HT Metering up to 12 KV on incommer.
c) 1 No.- (0 - 60 A) dual scale Ammeter, digital type, selector switch for ammeters.
d) 1 No - Microprocessor based numericak relay with O/C, E/F and S/C protection.
e) 1 No - set of dual core dual ratio 3 CTs 60/5A of 15 VA burden and accuracy class 0.5 for metering and class 5P10 for protection.
f) 1 No. electronic type digital energy analyser having 30 days memory and parameters of KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories.
g) 1 No. hooter with hooter acceptance and reset push button.
h) 1 No - Red, Yellow & Blue for phase indication.
i) 1 No - Amber for Trip indication.
j) 1 No - Red `ON' Green `OFF'indication.
k) 1 No - Spring charge indication.
l) 1 No - Auto trip indication.
m) 1 No. master trip relay. (Electromechanical Type ) n) 1 No.Trip ckt supervision relay. (Electromechanical Type ) H.T. Panel described as above
2
-
-
Supplying, Installation, Testing and Commissioning of oil immersed ONAN cooled 100 KVA, 11 KV /0.433 KV, 3 phase, 50 Hz delta/star-11 connected, outdoor type, copper wound transformer, complete with all fittings such as oil conservator, silica gel breather, thermometer, explosion vent with off Load arrangement on HV side with Tapping for variations of high voltage from (+) 5% to (-) 15% in steps of 2.5% each with integrated microprocessor based, bi-directional roller, diagrams & rating plate, Oil temperature indicator, & Winding temperature indicator, Buchholz relay, weather proof Marshalling Box, lifting lugs, first filling of oil, weather proof H.Tcable box & 150 sqmm Aluminium Cable connection etc. complete as per specification. All relays, contacts & CT terminals to be wired upto marshalling box. The transformer losses shall be as per IS 1180 part-1 (2014) level-2 or ECBC-2017 and BEE Star rating -1.
2
-
-
Design, Manufacturing, Supply, Installation, Testing & commissioning of Main LT Panel Cum capacitor panel. The panel will be totally enclosed type with, free standing, floor mounted, outdoor duty, dust & vermin proof, , front operated, electrical panel fabricated from 2 mm thick CRCA Sheet as per specifications & drawing laid in this document and will be complete with the main and auxiliary bus bars, ammeter, ammeter selector switch, voltmeter, voltmeter selector switch, indication lamps, CT's, protection MCB, interconnection wiring, earth bus and will be powder coated finish with 50 micron thickness. The Main LT Panel shall use all draw out type breakers suitable for 415 V AC, 3 phase, 50 Hz, 3 phase 4 wire supply system. The panel shall have Load Management, AMF facility & interlocking through PLC to achieve electrical interlocking, buscoupler switching, auto operation of incommer and bus coupler, auto start of D.G. Sets, auto D.G. running by pre set timing, auto changeover etc and having following incomming and outgoing Moulded case Circuit Breakers, MCB's as per the drawing and specification.
INCOMINGS
1 No. 200 Amp FP Moulded Case Circuit Breaker.
1 No. 160 Amp FP Moulded Case Circuit Breaker.
1 No. 200 Amp FP Contactor.
1 No. 160 Amp FP Contactor.
BUSBARS
250 Amp Amp TPN busbars of aluminium alloy as per SLD.
OUTGOINGS
5 Nos. 100 Amp TP+N Moulded Case Circuit Breaker.
3 Nos. 40 Amp TPN Miniature Circuit Breaker.
3 Nos. 32 Amp TPN Miniature Circuit Breaker.
3 Nos. 25 Amp TPN Miniature Circuit Breaker.
INSTRUMENTS
INSTRUMENTS
1 Nos. digital AVF Meter (96mm square).
2 Sets of phase indicating lights (RYB) with protection SP MCB.
2 Sets breaker 'ON' & 'OFF' indicating lamp.
1 Sets of 3 Phase O/V and U/V relay with time delay (O/V - 110% to 140% U/V - 40% to 80%).
1 Nos. master trip relay (one for each Incoming Breaker).
CAPACITOR BANK PANEL (35 KVAR - 1 SET) (PART OF MAIN L.T. PANEL) AS PER SLD
INCOMING
1 Nos. digital AVF Meter (96mm square).
1 Sets of phase indicating lights (RYB) with protection fuses .
1 Sets breaker 'ON' & 'OFF' indicating lamp (one set for each incoming breaker).
4 Step Automatic Power Factor Correction relay (APFC relay).
BUSBARS
150 Amp TPN busbars of aluminium alloy as per SLD.
OUTGOING
2 Nos. 63 Amp TPN MCCB.
2 Nos. 20 Amp TPN MCCB.
2 Nos. capacitor duty contactor (one for each 10 KVAR capacitor unit).
2 Nos. capacitor duty contactor (one for each 5 KVAR capacitor unit).
2 Nos. 10 KVAR heavy duty Capacitor Bank (440 Volt).
2 Nos. 5 KVAR heavy duty Capacitor Bank (440 Volt).
4 sets of push button stations Red and Green for operation of capacitor units with auto/manual selector switches.
1 No. Indicating lamp for each 10 / 5 KVAR capacitor unit to indicate that the unit is 'ON'.
1 No Power factor meter.
Panel describe as above
2
-
-
Supplying of 11 KV grade aluminium conductor, cross linked polyethylene (XLPE) insulated individual core screened, flat steel/strip armoured PVC sheathed cable (UE) complete as required.
3 core x 95 sq. mm
50
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.
Upto 120 sq. Mm
60
-
-
supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :
95 sq. Mm
2
-
-
First aid box as approved by St.John Ambulance Brigade /Indian Red Cross society conforming to IS : 2217 - 1963.
2
-
-
Shock treatment chart duly mounted on a wooden frame with glass on, as required in 2 languages (Hindi & English).
2
-
-
Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652 -2006.
15
-
-
Rubber mat 1000 mm. Wide to withstand 1.1 KV dielectric strength as per latest IS 15652-2006.
25
-
-
Supplying and installing at approved location approved make fire buckets (4 Nos.) of 24 gauge galvanized steel sheet conforming to IS: 2546, standard 9.5 litre capacity and of round bottom shape, painted white inside and red outside and black on the bottom, inscribed with letters “FIRE” in black and gold. Cost shall be inclusive of providing MS stand duly painted over a coat of primer.
2
-
-
Supply & Laying of following sizes of 1.1KV grade multicore copper conductor PVC insulated and PVC sheathed armoured control cable conforming to IS:7098 (Part-I) 1988, including end termination with brass compression gland and copper lugs.
4 core, 1.5 sq.mm
30
-
-
8 core, 1.5 sq.mm
125
-
-
12 core, 1.5 sq.mm
50
-
-
Providing, installation testing & commissioning of 'Silent Type' Diesel Generating Set along with having prime power rating 82.5 KVA, 415 Volts at 1500RPM, 0.8 lagging Factor at 415 V suitable for 50 Hz, 3 phase system and for 0.85 load factor and consisting of the following:-
Diesel Engine
Diesel Engine 4 stroke radiator cooled, electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 400C, 50% RH & at 1000 metre MSL and confirming to BS 5514, BS 649, is 10000, capable of taking 10% overloading for one hour after 12 hours of continuous operation. The engine will be fitted complete with all the required accessories. Engine Mounted Instrument Panel fitted with and having digital display for following:
Start- stop switch with key.
Water Temperature indication
Lubrication Oil pressure indication
Battery charging indication
RPM indication
Over Speed trip Indication
Low lubrication oil trip indication
Engine Hours Indication
Alternator:
Synchronous alternator rated at 82.5 KVA, 415 Volts at 1500 RPM, 3 phase 50 Hz, AC Supply with 0.8 lagging power factor at 400C, 50% RH & at 1000 metre MSL. The alternator shall be having SPDB enclosure, brushless, continuous duty, self-excited and self-regulated through AVR confirming to IS:4722/ BS 2613 suitable for tropical conditions and with class- F insulation. Alternator shall have provision of end termination of Aluminium Bus Duct.
Base Frame & Foundation
Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer.
Fuel Tank:
Daily service fuel tank of 150 litres capacity, fabricated out of 3mm thick M.S. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class 'C pipes of suitable dia. Complete with valves level indication & accessories as required as per specifications.
Exhaust System :
Dry exhaust mainfold with hospital grade exhaust silencer.
Starting System:
24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with 2 Nos. of batteries (25 plates, 160 AH lead Acid type) as required as per specifications.
Accoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air into the atmosphere as per specifications. The Acoustic Enclosure shall be factory fitted by the OEM.
Diesel Generating Set including Acoustic Enclosure. described as above.
2
-
-
Supply, Installation, Testing and Commissioning of following sizes MS exhaust piping heavy duty conforming to IS:3589 complete with all accessories such as bends, flanges, stainless steel flexible bellows etc. as required.
100 mm dia MS pipe. (5.0 mm thick)
10
-
-
Providing & Fixing of Insulation and aluminium cladding for exhaust piping using 75 mm thick rockool of density 150 Kg/ M3 & 24 SWG Aluminium Sheet.
10
-
-
Civil external service connections
1
-
-
Local Body approvals including tree cutting etc.
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements