Public Works Building And NH Department Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 21,97,589Document Cost
₹ 20,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2022_PWBNH_25261_6Bid Award Id
ViewTender No
CS/T/TB-I/17/2022/5 Dated Guwahati 25th April 2022Tender Authority
Public Works Building And NH Department ViewPurchaser Address
-Website
http://https://pwdbnh.assam.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
EARTH WORK Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.
All kinds of soil
4434.32
-
-
LAND FILLING
Excavating, Supplying and filling of local earth(inculding Royality) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete
16333.5
-
-
PLINTH FILLING
filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
2629.49
-
-
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
1284.25
-
-
ANTI_TERMITE AND DPC
Supplying chemical emulsion in sealed containers including delivery as specified.
Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
883.8
-
-
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :
Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall & rodding etc. complete:
With Chlorpyriphos/ Lindane E.C. 20% with 1%
concentration
491
-
-
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)
221.62
-
-
PCC & RCC
PCC Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
594.7
-
-
RCC Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.
Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content
in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
All works upto plinth level
Concrete of M25 grade with minimum cement content of 330 kg /cum
797.87
-
-
Concrete of M25 grade with minimum cement content of 330 kg /cum
479.08
-
-
Add for using extra cement in the items of design mix over and above the specified cement content therein.
364.84
-
-
REINFORCEMENT
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
82498.55
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
44652.78
-
-
CSHUTTERING
entering and shuttering including strutting, propping etc. and removal of form for
Foundations, footings, bases of columns, etc. for mass concrete
571.65
-
-
Columns, Pillars, Piers, Abutments, Posts and Struts
2689.88
-
-
Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick
1957.18
-
-
Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick
1906.23
-
-
BRICK WORK
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
Cement mortar 1:6 (1 cement : 6 coarse sand)
304.44
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
Cement mortar 1:4 (1 cement :4 coarse sand)
2786.15
-
-
WOODEN DOORS Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).
Salwood
1.23
-
-
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for
separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)
Second class teak wood
35 mm thick shutters
52.92
-
-
Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :
125x64x2.50 mm
120
-
-
Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :
300x16 mm
20
-
-
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :
250x10 mm
40
-
-
Providing and fixing chromium plated brass handles with necessary
screws etc. complete:
125mm
40
-
-
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
20
-
-
Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary
screws etc. complete.
33
-
-
Providing and fixing PVC Door Frame of size 50x47 mm with a wall thickness of 5 mm (± 0.2 mm), made out of single piece extruded PVC profile, with mitred cut joints and joint with 2 nos of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20 mm M.S. rectangular tube of 0.8 mm , including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The door frame to be fixed to the wall using 8 x100 mm long anchor fasteners complete, all as per manufacturer's specification and direction of Engineer -in- charge.
141.3
-
-
35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineerin- charge.
Decorative finish (wood grained finish)
49.77
-
-
ALUMINIUM DOOR & WINDOW
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately)
For fixed portion
Powder coated aluminium (minimum
thickness of powder coating 50 micron)
3209.37
-
-
For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
Powder coated aluminium (minimum thickness of powder coating 50 micron)
279.22
-
-
Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge.
Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side
43.14
-
-
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):
With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
59.38
-
-
Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-incharge
Powder coated minimum thickness 50 micron aluminium
44
-
-
Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).
220.59
-
-
FALSE CEILING
Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner
with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.
12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.
234.59
-
-
S.S RAILING
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with
necessary stainless steel nuts and bolts complete, i/c fixing the railing
with necessary accessories & stainless steel dash fasteners , stainless
steel bolts etc., of required size, on the top of the floor or the side of
waist slab with suitable arrangement as per approval of Engineer-incharge,
(for payment purpose only weight of stainless steel members
shall be considered excluding fixing accessories such as nuts, bolts,
fasteners etc.).
3644.1
-
-
FLOORING Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
Size of Tile 600x600 mm
688.56
-
-
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
Glazed Vitrified tiles Matt/Antiskid finish of size
Size of Tile 600 x 600 mm
157.28
-
-
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
298
-
-
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
Granite stone slab all colour and texture except black, Cherry/Ruby red
Area of slab over 0.50 sqm
282.6
-
-
Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :
Light shade pigment using white cement
102.4
-
-
62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.
515
-
-
Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.
18 mm thick
177.67
-
-
PLASTERING WORK
12 mm cement plaster of mix :
1:6 (1 cement: 6 fine sand)
8176.6
-
-
15 mm cement plaster on the rough side of single or half brick wall of mix :
1:4 (1 cement: 4 fine sand)
2241.12
-
-
12 mm cement plaster finished with a floating coat of neat cement of mix
1:4 (1 cement: 4 fine sand)
835.41
-
-
PAINTING WORK
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
12736.37
-
-
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :
New work (two or more coats) over and including water thinnable priming coat with cement primer
7583.08
-
-
Finishing walls with textured exterior paint of required shade :
New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
7136.41
-
-
Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and
manufacture, including applying additional coats wherever required, to achieve even shade and colour.
Two coats
5599.96
-
-
Applying priming coat:
With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works
1186.69
-
-
Polishing on wood work with ready mixed wax polish of approved brand and manufacture :
New work
32.76
-
-
PLINTH PROTECTION & WATERPROOFING
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed andconsolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
267.5
-
-
Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.
142
-
-
MS ROOF TRUSS
Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.
6.3
-
-
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:
Fixing with adjustable lugs with split end tail to
each jamb
32.4
-
-
Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.
80x1.20 mm M.S. laths with 1.20 mm thick top cover
18
-
-
Providing and fixing ball bearing for rolling shutters.
18
-
-
Extra for providing mechanical device chain and crank operation for
Exceeding 10.00 sqm and upto 16.80 sqm in the area
18
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and
applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
Hot finished welded type tubes
41638.3
-
-
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge)
0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
1165
-
-
Providing and fixing 50 mm thick extruded polystyrene rigid insulation board of required size underdeck on ceiling surface, complying with ISO 4898:2008 & ASTM C 578-08b - type VI, having thermal conductivity of 0.0289 W/m K as per ASTM C 578 (measured as per IS 3346), compressive strength of 350 kPa listed as per ASTM D 1621, density of 34-36 kg/cum as per ASTM D 1622, water absorptions ? 1% by volume as per ASTM D 2842, oxygen index of 24.1 to 28.1 listed as per ASTM D 2863, cell size 0.4 mm of dia (max) as per ASTM D 3576. Fire retardent property as per DIN 4102, Part 1 of class B2 and as per ASTM E84 class A, fixed with suitable water based adhesive and fastener, complete in all respect as per the direction of Engineer-in-Charge.
1165
-
-
FENCING
Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)
1060
-
-
Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.
4240
-
-
Welded steel wire fabric fencing with posts of specified material and of standard design placed and embedded in cement concrete blocks 45x45x 60 cm of mix 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size), every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and struts embedded in cement concrete blocks 70x45x50 cm of the same mix, provided with welded steel wire fabric fixed between the posts fitted and fixed with G.I. staples on wooden plugs or tied to 6 mm bar nibs with G.I. binding wire (cost of posts, welded steel wire fabric, painting, earth work in excavation and concrete to be paid for separately).
489.6
-
-
PAVER BLOCK
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.
60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.
3600
-
-
Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.
3900
-
-
Cutting road and making good the same including supply of extra quantities of materials i.e. aggregate, moorum screening, red bajri
and labour required. Water bound macadam
2215
-
-
Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :
Cement mortar 1:6 (1 cement : 6 coarse sand)
776.25
-
-
Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.
9182
-
-
FOLIAGE AND SHADE LOVING PLANTS
Providing and displaying of Aglaonema Butterfly having ht.30 cm 10 to 12 fresh, healthy and attractive colorful leaves, well developed in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge.
50
-
-
Providing and displaying of Aglaonema Dove variety having ht. 30 cm to 45 cm with 8 to 10 leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.
50
-
-
Providing and Displaying of Aglaonema Sam plant ht.30 cm well developed three in one, having 18 to 20 fresh, healthy and attractive colorful leaves in 35 cm size Earthen pot/Chali/Tray & as per direction of the officer-in-charge.
50
-
-
Providing and displaying of Aglaonema Silver Queen having 30 cm to 45 cm. ht. with 12 to 15 leaves, multi suckers, fresh and healthy leaves, well developed in 25 cm dia Earthen pot/Plastic pot & as per direction of the officer-in-charge.
50
-
-
Providing and displaying of Aglaonema nitida having ht. 30 cm to 45 cm with 8 to 10 leaves, well developed, fresh and healthy with attractive leaves
in 25 cm size of Earthen pot/Plastic pot.& as per direction of the officer-in-charge.
50
-
-
Providing and Displaying Allyssum white in full bloom well developed fresh & healthy Plant in 20 cm Earthen Pot/Plastic Pot and as per direction
of the officer-in-charge.
50
-
-
Providing and Displaying Anemone hybrid (3 in one) variety well developed with fresh & healthy Flower in full bloom in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
50
-
-
Providing and Displaying Asiatic lilly hybrid variety (3 in one) in each pot having in full bloom 3 to 5 flowers 30 to 45 cm ht. well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
50
-
-
Providing and Displaying Brachycome well developed with fresh & healthy foliage with 100 to 120 flowers stacking with green painted bamboo stick in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
50
-
-
Providing and Displaying Chrysanthemum single named variety in different colour well developed, having 45 to 60 cm ht., minimum 150 and above half bloom flowers well stacked with bamboo stick having three layer tiding by thread fresh and healthy foliage in 30 cm Earthen Pot and as per direction of the officer-in-charge.
50
-
-
Providing and Displaying Cyclamen hybrid variety fresh & healthy in full bloom well developed in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.
50
-
-
Providing and Displaying Helianthus different colour with full bloom (3 in one) fresh & healthy in 25 cm Earthen Pot/Plastic Pot well developed as per direction of the officer-in-charge.
50
-
-
Providing and Displaying Creeper Rose variety 3 to 4 healthy branch 60 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.
50
-
-
Providing and Displaying Bamboo Buddha vally variety with umbrella shape having 120 to 135 ht. with fresh & healthy foliage well developed in 40 cm Cement pot multy branch, bushy as per direction of the officer-in-charge.
10
-
-
Providing and Displaying Ficus Retusa topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180 to 210cm ht in 40 cm Cement Pot as per direction of the officer-in charge.
10
-
-
Providing and fixing solid sports flooring of high density dual colour sealed foam shock absorber with three layered closed cell foam of glass fiber layer then surface disposed layer (anti skid) to provied including all.
Make-Alptahls (Austria)
525.71
-
-
Supply and installation of FIFA approved goalposts including net
1
-
-
INTERNAL PLUMBING
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc
complete.
20
-
-
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white
P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and
fixtures complete, including cutting and making good the walls and floors wherever required:
Long pattWhite Vitreous china Orissa pattern W.C. pan of size
580x440 mm with integral type foot restsern W.C Pan of size 580x440 mm
1
-
-
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass
pillar taps, 32 mm C.P. brass waste of standard pattern, including
painting of fittings and brackets, cutting and making good the walls
wherever require:
White Vitreous China Flat back wash basin size 550x
400 mm with single 15 mm C.P. brass pillar tap
22
-
-
Providing and fixing white vitreous china pedestal for wash basin
completely recessed at the back for the reception of pipes and fittings.
22
-
-
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.
13
-
-
Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.
39
-
-
Providing and fixing stainless steel A ISI : 304 (18/8) kitchen sink as per IS : 13983 with CI brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required.
Kitchen sink without drain board
470x420 mm bowl depth 178 mm
4
-
-
Providing and fixing C.P. brass long nose bib cock of approved quality
conforming to IS standards and weighing not less than 810 gms.
4
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. [for Basin / Urinal / Sink waste]
40 mm dia
60
-
-
50 mm dia
25
-
-
Supplying, Fixing of C.P. brass twin coat hook.Make : Jaquar Cat no. CAN-1161N or Hindware & Kohler.
21
-
-
Supplying, Fixing C.P. hand spray with lever control (health faucet) and flexible hose 1 m long connection with C.P. holder for hand spray complete in all respects.
20
-
-
Health faucet -Make : Jaquar Cat no. ALD-565 or Hindware & Kohler. Supplying, Fixing C.P. 2 IN 1 Bib cock Jaquar Cat no. CON-041KN , Hindware & Kohler.
20
-
-
Providing and fixing PTMT soap Dish Holder having length of 138mm,
breadth 102mm, height of 75mm with concealed fitting arrangements,
weighing not less than 106 gms.
30
-
-
Providing and fixing C.P. brass angle valve for basin mixer and geyser
points of approved quality conforming to IS:8931
60
-
-
Providing and fixing soil, waste pipes : Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905
100 mm dia
180
-
-
75 mm diameter : vent pipes :
5
-
-
Providing and fixing M.S. holder-bat clamps of approved design to sand cast iron / cast iron (spun) pipes embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls, etc.
For 100mm diametre
45
-
-
For 75mm diametre
2
-
-
Providing and Fixing shielded coupling for Hubless centrifugally cast iron pipe. 100 mm
SS 304 grade coupling with EPDM Rubber gasket.
45
-
-
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905
100 mm dia
15
-
-
75 mm dia
2
-
-
Providing and fixing plain bend of required degree. 100 mm dia
20
-
-
75 mm dia
2
-
-
Providing and fixing double equal plain junction of required degree.
100x100x100x100 mm
15
-
-
75x75x75x75 mm
2
-
-
Providing and fixing single equal plain junction of required degree : 100x100x100 mm
10
-
-
75x75x75 mm
2
-
-
Providing and fixing double unequal plain junction of required degree :
100x100x75x75 mm
5
-
-
Providing and fixing single unequal plain junction of required degree :
100x100x75 mm
5
-
-
Providing and fixing double equal plain invert branch of required degree:
100x100x100x100 mm
5
-
-
Providing and fixing single equal plain invert branch of required degree :
100x100x100 mm
10
-
-
Providing and fixing single unequal plain invert branch of required degree :
100x100x75 mm
5
-
-
Providing and fixingHubless centrifugally cast (spun) iron terminal guard (slotted
cowl) -100 mm dia as per IS 15905
12
-
-
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
100 mm inlet and 100 mm outlet
Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905
25
-
-
Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing
drain pipe etc. and repairing the hole after insertion of drain pipe etc.
with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded
stone aggregate 20 mm nominal size), including finishing complete
so as to make it leak proof.
25
-
-
Cutting chases in brick masonry walls for following diameter sand cast iron / centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 12.50 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand).
100 mm
18
-
-
75 mm
2
-
-
Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and fittings with paint of any colour such as chocolate, grey or buff, etc., over a coat of primer (of approved quality) for new work.
100mm diametre pipe
180
-
-
75mm diametre pipe
5
-
-
WATER SUPPLY
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having
thermal stability for hot & cold water supply, including all CPVC plain &
brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.
This includes jointing of pipes & fittings with one step CPVC solvent
cement and the cost of cutting chases and making good the same
including testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls
etc.(Concealed Work)
15 mm nominal outer dia Pipes
25
-
-
20 mm nominal outer dia Pipes
125
-
-
25 mm nominal outer dia Pipes
75
-
-
32 mm nominal outer dia Pipes
52
-
-
40 mm nominal outer dia Pipes
10
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including
trenching and refilling etc.
15 mm nominal outer dia Pipes
2
-
-
20 mm nominal outer dia Pipes
30
-
-
25 mm nominal outer dia Pipes
30
-
-
32 mm nominal outer dia Pipes
100
-
-
40 mm nominal outer dia Pipes
50
-
-
50 mm nominal outer dia Pipes
30
-
-
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,
with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :
With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
2
-
-
Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :
40 mm diameter pipe
150
-
-
50 mm diameter pipe
50
-
-
Providing and fixing brass bib cock of approved quality.
15 mm nominal bore
20
-
-
20 mm nominal bore
2
-
-
Providing and fixing gun metal gate valve with C.I wheel of approved quality (screwed end).
32 mm nominal bore
12
-
-
40 mm nominal bore
12
-
-
50 mm nominal bore
10
-
-
65 mm nominal bore
2
-
-
Providing and fixing ball valves (brass) of approved quality, High or Low pressure with plastic floats complete.
20 mm nominal bore
6
-
-
25 mm nominal bore
6
-
-
Cutting holes up to 15 x 15 cm in R.C.C floors and roofs for passing pipes etc. and repairing the holes after insertion of pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggeragate 20 mm nominal size) including finishing complete so as to make it leak proof.
20
-
-
Making holes up to 20 x 20 cm and embedding pipes up to 150 mm dia in masonry and filling with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggeragate 20 mm nominal size) including dispoal of malba.
10
-
-
Providing and placing on terrace (at all floor levels) polyethylene water
storage tank, IS : 12701 marked, with cover and suitable locking
arrangement and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank.
20000
-
-
DRAINAGE
Providing, laying and jointing single wall corrougated PVC lateral drain pipe with perforation and synthetic filter confirming IS 9217-2004 including testing of joints etc. complete . (Astral Geo-Rex) for ground water dewatering.
100 mm
790
-
-
65 mm
1610
-
-
Providing, laying and jointing glazed stoneware pipes class SP-1
with stiff mixture of cement mortar in the proportion of 1:1 (1 cement
: 1 fine sand) including testing of joints etc. complete :
100 mm
15
-
-
160 mm
65
-
-
200 mm
10
-
-
250 mm
5
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W pipe including bed concrete as per standard design.
150 mm Diameter S.W Pipe
90
-
-
200 mm Diameter S.W Pipe
10
-
-
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:
100x100 mm size P type
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
10
-
-
Providing and laying non-pressure NP2 class (light duty) R.C.C.
pipes with collars jointed with stiff mixture of cement mortar in the
proportion of 1:2 (1 cement : 2 fine sand) including testing of joints
etc. complete :
150 mm dia. R.C.C. pipe
25
-
-
250 mm dia. R.C.C. pipe
50
-
-
300 mm dia. R.C.C. pipe
50
-
-
Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with R.C.C top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) and inside plasreting 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
With common burnt clay F.P.S (non-modular) bricks of class designation 7.5
25
-
-
Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal dimeter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) :
With common burnt clay F.P.S (non-modular) bricks of class designation 7.5
2
-
-
Extra for depth of manholes
Size 90x80 cm With common burnt clay F.P.S (non-modular) bricks of class designation 7.5
2
-
-
Size 120x90 cm With common burnt clay F.P.S (non-modular) bricks of class designation 7.5
2
-
-
Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete :
For pipes 100 to 250 mm diameter
2
-
-
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.
2
-
-
Providing and fixing in position pre-cast R.C.C. manhole cover and
frame of required shape and approved quality
M D - 10
Circular shape 500 mm internal diameter
6
-
-
DEEP TUBE WELL WORKS
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.
All types of soil
300 mm dia
100
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.
200 mm nominal size dia
75
-
-
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.
32
-
-
Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge
12
-
-
Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineerin- charge.
2
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed
and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with
outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges,
fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge.
150 mm nominal size dia having minimum wall thickness
5.00 mm
35
-
-
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc.,
all as per requirement and direction of Engineer-in-charge.
6
-
-
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:
200 mm dia
1
-
-
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.
200 mm clamp
20
-
-
Providing and fixing Bail plug/ Bottom plug of required dia to the
bottom of pipe assembly of tubewell as per IS:2800 (part I).
150 mm dia
10
-
-
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
40
-
-
Providing and fixing in position pre-cast R.C.C. manhole cover and
frame of required shape and approved quality
M D - 10
Circular shape 500 mm internal diameter
10
-
-
PUMP Hydropneumatic System for OHT Tank Filling
Supply, installation & commissioning of 2 Nos. Vertical Multi Stage Centrifugal Pump for Clear Water with 50Hz, 380-415V, 2 Pole IE3 efficiency class motor (As per IEC standard). Pump shall be CI with CED quoted- Suction & Discharge Casing, SS 316 -Shaft and all other components will be with SS 304, Mechanical Seal (SiC vs SiC face) . Pump should have minimum 70% efficiency.
Pump controller suitable for 2 Pumps (1W+1S) with LCD screen displays, phase loss protection (incoiming as well as for outgoing), Individual pump overload protection, individual pump under voltage protection, dryrunning protection without installing any float switch, memory function when power off and during recovery, visual and audio alarm for fault prompt, auto manual switch, and pump should operate based on the sump water level and both pump should run together for high level. Panel should come with 3 Nos Float switch to work as per the sump water level.
Flow Rate-15 m3/hr (1W+1S)
Head-15m
1
-
-
Submersible Borewell Pump
Supply installation & Commissioning of submersible borewell pump with SS 304-Casing/Impeller/Shaft & Mechanical seal coupled with a 380-415V, 50Hz 2 Pole, Insulation Class-F, IP 68 Protected Rewindable Electric Motor (Motor Make-.TESLA/FRANKLIN)
Pump controller suitable for 1 Pump with LCD screen displays, phase loss protection (incoiming as well as for outgoing), Individual pump overload protection, individual pump under voltage protection, dryrunning protection without installing any float switch, memory function when power off and during recovery, visual and audio alarm for fault prompt, auto manual switch, and pump should operate based on the UGT water level. Panel should come with 1 No. Float switch to work as per the sump water level.
Flow Rate Per Pump-11.5 m3/hr (1 No.)
Head-30m
1
-
-
SH:-I (WIRING)
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch,modular plate, suitable GI box and earthing the point with 1.5sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.
Group - C
310
-
-
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.
Group - C
130
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
110
-
-
4 X 6 sq. mm + 2 X 6 sq. mm earth wire
50
-
-
4 X 10 sq. mm + 2 X 6 sq. mm earth wire
50
-
-
WIRING IN STEEL AND PVC CONDUIT (Power Point)
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
1310
-
-
Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
1080
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing following modular switch & socket, connection etc. as required.(For Computer)
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A
modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).
115
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular
switch, connections etc. as required
40
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A
modular switch, connections etc. as required.
85
-
-
SH:-II (FITTING & FIXTURES)
Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
38
-
-
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc.as required.
35
-
-
SITC of Recess mounted Round LED Downlight with pressure die cast
Aluminium housing and high transmitive PS diffuser, 24W ,Minimum 2400 Lumen, 5700K, i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.. Wipro Make Mollis LED (LD06),CAT No. LD06-301-XXX-57-XX or equivalent approved make
135
-
-
SITC of Wall Surface mounted Square LED light with pressure die cast Aluminium housing and high transmitive PMMA diffuser, 9 W, Minimum 650 Lumen, 6000K,i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.Wipro Make Moon Square LED (LW02),CAT No. LW02-101-XXX-60-XX or equivalent approved make
95
-
-
SITC of pendant mounted fittings of all complete with all accessories, connection etc. as required.
SITC of Ceiling/Wall surface/Pendant mounted LED Linear profile ,extruded Aluminium housing and PC diffuser, 40 W, Minimum 4000 Lumen complete with all accessories, connectionsuitiable for operation on 240 Volt and 50 Hz power supply, . etc. as required. Wipro Make Optima LED (LL24),CAT No. LL24-541-XXX-57-CD or equivalent approved make
3
-
-
SITC of Integral, SMD LED, IP 65, 140W LED Surface/Suspend Mounted, Round Mid-Bay / High-Bay, 135 lm/W. ,Die Cast Aluminium Housing.i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. Wipro Make Uno LED (LH21), CAT No. LH21-222-060-57-XX or equivalent approved make
27
-
-
Mirror light, surface mounted 600mm LED, PC housing and PC diffuser,10 W , Minimum 900 Lumen..i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. Wipro Make Trim LED (LL20), CAT No. LL20-111- XXX-65NE3, Wipro Make or equivalent approved make
35
-
-
SH:-III (MCB DBs)
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
6 way (4 + 18), Double door
5
-
-
8 way (4 + 24), Double door
5
-
-
Supplying and fixing following rating, TP/ FP MCB/MCCB in the existing MCB DB complete with connection testing and commissioning etc as reqd. 63 A TP MCB
10
-
-
Supplying and fixing 5 amps to 32 amps rating, 240 / 415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Single pole
115
-
-
SH:-IV (EARTHING) Supply, installation, testing and commissioning of 50 x 6 mm GI Equipotential bar of 500 mm length with suitable. junction box to connect earthing conductor from building earthing to the equipment. With six knock outs for connecting the equipment earthing
2
-
-
SH-VI (CABLE AND CABLE TRAYS)
Cable Tray
MS perforated cable tray Hot Dipped Galvanized 150 X 50 X 1.6 mm
190
-
-
SH: IX (MV PANEL)
Supply, installation, assembly, connection, testing and commissioning of MAIN LT PANEL (OUTDOOR TYPE) as per Drawing ,Specification, Technical Data sheet & IS.
1
-
-
Supply, installation, assembly, connection, testing and commissioning of DG AMF PANEL (OUTDOOR TYPE) as per Drawing ,Specification, Technical Data sheet & IS.
1
-
-
Supply, installation, assembly, connection, testing and commissioning of EXTERNAL LIGHTING FEEDER PILLAR (OUTDOOR TYPE) as per Drawing ,Specification, Technical Data sheet & IS.
4
-
-
SH-XI (FIRE EXTINGUISHERS)
Supplying, installing, testing and commissioning of 4.5 Kg capacity stored pressure type carbon dioxide type fire extinguishers made from brand new seamless drawn steel cylinder as per IS 7285 with ISI mark, fitted with wheel valve as per IS 3224 with ISI mark, with discharge bend and horn and complete with initial charge as per IS 15683 with ISI mark and wall bracket complete as required.
1
-
-
Supplying, installation, testing and commissioning of ABC stored pressure type Fire extinguishers of 4 KG capacity fitted with discharge control valve and pressure gauge, filled with mono ammonium phosphate powder as per EN 3615 approved and supplied complete with initial charge as per IS: 15683 with ISI mark and wall bracket complete as required.
1
-
-
SH-XII (VENTILATION SYSTEM)
VENTILATION SYSTEM FOR TOILETS
Supply, installation, testing and commissioning of Propellar / In - Line Exhaust / Fresh air fan for Toilets ventilation system. The Motor shall run on the electrical power suitable for 1 Ph/3Ph 50Hz.
150 CFM Propellar Type 10" dia
45
-
-
EXTERNAL ELECTRICAL
EXTERNAL LIGHT
SITC of 35W, Post Top LED with aluminium housing, UV resistant powder coated black finish, lumen ≥ 3325 lumens ,.i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required..Wipro Make LED (LP07),CAT No. LP07-431-XXX-57-CL or equivalent approved make
80
-
-
SITC of 35W, Gate light, LED with aluminium housing,minimum 90 lm/W. CRI-80, IP66, i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.Wipro Make Post Top LED (LP06),CAT No. LP06-351-XXX-57-XX or equivalent approved make
4
-
-
SITC 7W,Bollard, LED, extruded Aluminium housing,6500K, lumen ≥ 402 lumens (57 lm/W).i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.Wipro Make Bollard LED (LB12),CAT No. LB12-880-XXX-65-08 or equivalent approved make
100
-
-
SITC of 18W LED Surface mounted outdoor type IP65 Down light fixture,die cast Aluminium housing. 6000 K ,i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.Wipro Outdoor Downlight (LD52),CAT No. LD52-301-040-060-XX or equivalent approved make
67
-
-
Supplying & Erection of hot dipped galvanized 16.0 Meter Octagonal GI Highmast suitable for 8 Nos. Floodlight luminaire. Bottom section thickness of 4mm and top section thickness of 3 mm. PCD of 445 mm along with 6 Nos. foundation bolts. Foundation bolt dimension of M30X850. Base plate dimension of 520mmX25mm ,Wipro Make or equivalent approved make
4
-
-
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.
960
-
-
Supplying of following size AL conductor armoured XLPE insulated PVC sheathed power cable of 1.1 KV grade ISI marked IS:7098(Part 1) 1988 with ammendment upto date as per following manner etc as required
2Cx10 sq.mm AL XLPE Armoured Cable
5450
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required
2Cx10 sq.MM. AL XLPE Armoured
50
-
-
Supplying & Erection of hot dipped galvanized 4.0 Meter Octagonal GI pole with top dia of 70mm, bottom dia 130 mm, PCD of 225 mm and Sheet thickness of 3mm.base plate dimension of 200mmX200mmX12mm, GI base plate,Wipro Make or equivalent approved make
80
-
-
Supply of SMD 200W LED Floodlight fixture, 100 lm/W (20000 lumens), die cast Aluminium housing with PC lens and toughened glass diffuser.i/c electonic driver and all other accesories suitable for operation on 240 V and 50 Hz i/c connection with 1.5 sq. mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required. Wipro Make Alpha LED (LF20,) CAT No. LF20-272-060-57-G2 or equivalent approved make ( for 16Mtr. High mast)
4
-
-
SH:-IV (EARTHING) Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
12
-
-
s
4
-
-
Supplying and laying 25 mm X 5 mm G.I strip
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm), Double run
180
-
-
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
100
-
-
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I.pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
60
-
-
Supplying and laying 50 mm X 5 mm copper strip
Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.
60
-
-
SH:-V (LIGHTNING CONDUCTOR)
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.( provide 3 meter GI pipe
30
-
-
Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required
30
-
-
Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting / sweating and soldering etc as required.
30
-
-
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)
1650
-
-
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)
1200
-
-
Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.
30
-
-
SH-VI (CABLE AND CABLE TRAYS)
Supply of following sizes of XLPE insulated PVC sheathed aluminium/copper conductor armoured cable of 1.1 KV grade on existing cable tray / surface including saddle, clamps etc. complete as required. Conforming IS 7098(Part 1) 1988
3.5Cx70 sq.mm AL. XLPE ARMOURED CABLE
150
-
-
4Cx16 sq.mm AL. XLPE ARMOURED CABLE
2000
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required
3.5Cx70 sq.mm AL. XLPE ARMOURED CABLE
4
-
-
4C X16 SQ. MM. AL XLPE Armoured
12
-
-
Cable laying through pipe
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.
Upto 35 sq. mm
1500
-
-
Above 35 sq. mm and upto 95 sq. mm
650
-
-
SH-VII (DG SET)
Supply, installation, testing and commissioning of silent type water cooled DG set conforming to latest environment protection regulations for emission and noise level comprising of radiator (CPCB II compliant with latest amendments), power pack, electronic governor, vertical multi-cylinder diesel engine equipped with flywheel having Prime Power Rating of 62.5 KVA, 415 Volts at 1500 RPM, 0.8 lagging power factor at 415 volt suitable for 50 Hz, 3 phase system & for 0.8 Load Factor and consisting of the followings:
Diesel Engine:
Full electronic authority diesel engine 4 stroke radiator water cooled, electric start with electronic fuel injection system of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50%RH & at 218.23 m MSL and conforming to BS:5514, BS:649, IS:10000, capable of taking 80% block load at the start and 10% over loading for one hour after 12 hours of continuous operation. The engine shall be fitted complete with all the required accessories.
Engine mounted instrument Panel fitted with digital display for following:
Start-stop switch with key
Water temperature indication
Lubrication oil pressure indication
Lubrication oil temperature indication
Battery charging indication
RPM indication
Over speed indication
Low lub. Oil trip indication
Engine Hours indication
Alternator :
Synchronous alternator rated for 62.5 KVA, 415 Volts at 1500 RPM , 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 218.23 m MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty, self-excited and self-regulated through AVR conforming to IS:4722/ BS:2613 suitable for tropical conditions and with class F/ H insulation.
1
-
-
Supplying and making cement concrete foundation 1:2:4 (1 cement, 2 coarse sand, 4 graded stone aggregate of 40 mm nominal size) i/c excavation, sand cushioning at the bottom and on all sides in accordance with manufacturers design i/c providing angle iron of size 35 x 35 x 5 mm thick on all the corners of foundation or as reqd. (DG Foundation)
1
-
-
SITC of exhaust gas piping of suitable dia. Welded black MS B Class pipe conforming to IS:3589 cut to required lengths and installed with necessary bends, supports and clamps, anti-vibration mountings, insulation of exhaust system with mineral wool/Rockwool, 50 mm thick wiremesh & aluminium cladding etc. as required as per specification
10
-
-
SH-VIII (TRANSFORMER)
Supply,insallation, testing and commissioning of 1 no. 63KVA, DYN11, 11000/415V, 50HZ, 3ph, Star rated, IS1180 level-2, Indoor type oil filled transformer, Copper winding having continuous rating of 63 KVA,The transformer shall have bottom entry cable end box on HV side for 3 x 300 sq.mm. XLPE cable and suitable flange (for vertical takeoff). The LV Box of transformer shall be suitable for terminating aluminum, Armoured, cable with all fitting and accessories complete as required, as per Specification, Technical Data sheet & latest IS as per Specification, Technical Data sheet & latest IS : IS 2026 (Part 1 to Part 5): with latest revisions
Rating: 63 KVA
Service : OUTDOOR
Cooling: ONAN.
No load voltage ratio: 11KV/415V.
Frequency: 50Hz.
Vector group: Dy11.
Type: Oil type
Tapping: +5% to -15% @ 1.25%, 16 Steps / 17 Positions, Fittings & accessories
SITC of 63 KVA, 11/0.415 KV Oil Type Transformer as per above specification
1
-
-
Supply of 11 KV, 3C x 95sq.mm. XLPE (UE) armoured cable. Conforming IS 7098(Part II) 1988
25
-
-
PSC pole erection for HT OH supply line
Providing of 8 Mtrs. Long, 200 Kgs. PSC Pole. Detail Specification and Standards shall be as per technical sprcification.
20
-
-
Erection of PSC Pole of 8 Mtr. Length in brick ballast and ramming the foundation, finishing with 150 mm thick cement concrete (1:3:6) layer on top with including excavation and refilling etc. as required. Detail Specification and Standards shall be as per technical sprcification.
20
-
-
Providing & Erection of Stay set complete (Galvanized) with 19/20 mm dia x 1.8 Mtr. Long Stay Rod, Anchor Plate of size 45 Cm. X 45 Cm. X 7.5 mm thimble, stay clamps, turn buckle (20 mm x 60 mm), 7/3.15 mm dia G.I. Stay Wire and strain insulator etc. in cement concrete 1:3:6 foundation including excavation and refilling etc. as required. Detail Specification and Standards shall be as per technical sprcification.
20
-
-
Providing & Erection of metallic vitrified danger notice board, to be erected as per IS. Detail Specification and Standards shall be as per technical sprcification.
20
-
-
Providing and Erection of Barbed wire on PSC Pole. Detail Specification and Standards shall be as per technical sprcification.
20
-
-
Providing and Erection of 11 KV Pin Insulator with Hardware. Detail Specification and Standards shall be as per technical sprcification.
20
-
-
Providing & Erection of MS Channel 75 x 40 x 6mm, 4 feet long complete with 50 x 6 flat iron clamps, bolts, nuts and washers drilling holes for cut point. Detail Specification and Standards shall be as per technical sprcification.
20
-
-
Providing and Erection of coil type earthing with 6 SWG GI earth wire with charcoal and salt from top of pole as per IE rules. Detail Specification and Standards shall be as per technical sprcification.
20
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required. : Upto 120 sq. mm.
55
-
-
Supplying and making straight through cable jointing with heat shrinkable jointing kit complete with all accessories including ferrules suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 120 sq. mm
2
-
-
SH-X (SAFETY ACCESSORIES)
Supply and labour charges for fixing, testing and commissioning of following accessories complete with fixing brackets etc. which shall be supplied by the tenderers with all necessary accessories, tools etc.
Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
2
-
-
Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
3
-
-
Providing first aid box as approved by St. John Ambulence Brigade/ Indian Red Cross confirming to IS 2217:1963
3
-
-
Supply and fixing of First Aid Chart in 5 mm glassed wooden frame ( approx front area 1.20 sqmt)
2
-
-
Supplying Fire buckets with round bottom made of GI sheet,24 SWG ,9.5 liters capacity painted inside white and outside red with a word FIRE on the face of the bucket stand to hang buckets made out of MS Angle iron frame work of size 40 X 40 X 6 mm
4
-
-
Supply and fixing Rubber mats of AC Voltage proof upto 3.3 kV grade 1.0 Mtrs x 0.9 Mtrs X 12mm or required thickness as required by the Electrical Inspectorate and confirming to IS 5424
5
-
-
Supply and fixing of Electric Shock treatment chart mounted on 5mm Glass wooden frame , Size - 50 x 70 cm, Rectangle including fixing on wall ( approx front area 1.20 sqmt)
2
-
-
Supply and fixing of Safety Instruction chart mounted on 5mm Glass wooden frame, Size - 50 x 70 cm, Rectangle including fixing on wall ( approx front area 1.20 sqmt)
2
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements