Public Works Building And NH Department Tender

Providing, fitting and fixing of Pillar Cock (Jaquar make. Catalogue No.:- CON-011KN) (Refer. Page No.:- 35)

250 mm X 300 mm X 100 mm deep 10'X12'

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe : 40 mm dia

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Supplying with fitting fixing of surface & wall mounted LED luminaries complete with all accessories including driver directly on wall / ceiling including connection with 1.5 sq mm P.V.C. insulated S.C.copper conductor as required and as directed by the department. (Crompton/PHILIPS/ BAJAJ/ Havells or equivalent considering the mother items rate and specification)_18W 4ft LED Batten

6 pin 15/16 amp socket outlet

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing, fitting and fixing of Rag. Bolt for Wash Basin (Jaquar make. Catalogue No.:- ZPS-MST-RB03) (Refer. Page No.:- 37)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete: 250x10 mm

3 pin 5/6 amp socket outlet

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

200 mm X 150 mm X 60 mm deep 8'X6'

Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length :20 mm nominal bore

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Construction of RCC foundation work of size 0.30M(L) X 0.30M(B) x 1.20M(H) for 6 / 7 mtr length Octagonel G.I. Steel Pole as specified and directed by the deptt.

16.0Sqmm 4core

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete : White solid plastic seat with lid

Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical Outdoor type floor mounting compartmentalize Timer Controll panel board of size 0.80M(B)X 0.90M(H) X0.40M(D) made of 16 SWG (1.66 mm) thick C.R. sheet and 35mm X 35mm X 5mm size angle having 4 nos legs at the bottom complete neatly wiring done with provision for one no 40A 4pole MCCB as incomer and out going as specified and directed by the deptt. confirming to IP 43 protection comprising of the following electrical items: 1. 25kA 40 Amp 4 pole 415 Volt 50 Hz MCCB as incomer - 1 no 2. 32 A DP MCB- 3 Nos 3. 25 mm × 5 mm size 4 strip copper Bus-Bar- 2 set. 4. 40 Amp 4 pole ON-OFF poser contactor - 1 No. 5. 20 Amp 2 pole ON-OFF poser contactor - 2 No. 6. Surface mounting Astronomical timer switch - 1 No. 7. Surface mounting Analog timer switch - 2 No. 8. 63 Amp bakelite HBC fuse kit-kat - 3 Nos

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required_5/6 amps switch

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall: 20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 24-12-2024: 65 mm nominal dia Pipes

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required_Single pole

Providing, fitting, fixing and testing of 2 way bib cock (Jaquar make. Catalogue No.:- FLR-5041N) (Refer. Page No.:- 31)

b) 7.0 Mtr Hight Galvenised Octagonal Pole

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement : 20 mm cement plaster

6.0Sqmm 4core

Providing, fitting, fixing and testing of Angle stop cock (Jaquar make. Catalogue No.:- CON-059KN) (Refer. Page No.:- 30)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Supply of following size PVC/XLPE insulated and PVC sheathed 1.1KV gd Solid Aluminum conductor up to 10 sqmm, balance stranded conductor, XLPE Insulated, cores laid up, PVC tape innersheathed, Armour (Aluminium wire for single core up to 70 sqmm, balance Aluminium strip, Glavanised wire for cables upto 2x10 sqmm,, 3x10 sqmm,,4x6 sqmm, & balance all galvanised steel strip), extruded PVC Type ST2 sheathed, 650/1100V grade as per IS 7908(Part 1) 1988 armoured U.G. cable as specified and directed by the deptt. ( Havells or equivelent make)_4.0Sqmm 4core

Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately. For the purpose of measurement the entire treated surface will be measured.

200 mm X 250 mm X 60 mm deep 8'X10'

Supplting amd errection of G.I. Octagonal of following length as per following specification : Conforming to grade S355JO Conforming to grade S355JO , Base Plate, Foundation Bolts, Pole Sections :- The Octagonal Poles shall be in single piece with single longitudinal welding join, Smart pack Junction box with 6 MCB & Terminals for mounting inside base compartment of Pole. Pole Foundation (Measured sepearatly):- The octagonal poles shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. Foundation work measured separately. (a) 6.0 Mtr Hight Galvenised Octagonal Pole

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as reqd_100 mm X 100 mm X 60 mm deep 4'X4'

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall: 25 mm nominal dia Pipes

Providing, fitting and fixing of Soap Dish (Jaquar make. Catalogue No.:- ACN-1131N) (Refer. Page No.:- 34)

Supplying including fitting fixing of following A.C. Ceiling fan (ISI Marked) complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. (USHA or Equivelent make)_1200mm Sweep

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 25 mm and up to 40 mm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Supplying with fitting and fixing of following LED Street Light fittings, testing and commissioning street light on existing pole / Structure including driver as required complete as directed and specified by the deptt. (Crompton, Wipro, Bajaj or equivalent considering the mother items rate and specification) (a) 70W, LED Street Light fittings (Surya or Equivelent make)

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Supplying including fitting and fixing of Hot Dip galvanised arm bracket for installation of luminaries.Header with top cap 300 mm long pipe of thickness 3 with arrangement to fix on pole top with 3 Nos. of bolts. i Armed of required length size 48.3mm out side dia x 3.25mm thick (Bajaj/ Philips/ Valmont/ Paruthi Engr/ Nezone Make) tiffener plate from arm of the following types : (a) Single arm bracket 1000mm long for 3m to 10 metre. Poles.

15/16 amp switch

150 mm X 75 mm X 60 mm deep 6'X4'

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

b) Double arm bracket 1000mm long for 3m to 10 metre. Poles.

Supplying fitting fixing offollowing 4P 240-440V 'C' Series 10ka MCB in the existing DB/panel as specified and directed by the department. (Havells or equivelent make)_63A 4P 240-440V 'C' Series 10ka MCB

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. (USHA or equivelent make)_300mm Sweep High speed Heavy duty

Applying priming coat: With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm

Providing, fitting and fixing of Towel Rail (Jaquar make. Catalogue No.:- ACN-1111SM) (Refer. Page No.:- 36)

Providing, fitting, fixing and testing of Health Faucet (Jaquar make. Catalogue No.:- ALD-573) (Refer. Page No.:- 32)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area beyond 3 sq. metres

Providing, fitting and fixing of Towel ring (Jaquar make. Catalogue No.:- ACN-1121BN) (Refer. Page No.:- 33)

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete. 10 litre (full flush) capacity-white

Supplying with fitting fixing of Reessed mounted LED luminaries complete with all accessories including driver directly on false ceiling including cutting ceiling & connection with 1.5 sq mm P.V.C. insulated S.C.copper conductor as required and as directed by the department. (Philips or equivalent considering the mother items rate and specification)_22W 300mmX300mm LED Recessed fitting

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work