Public Works Building And NH Department Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 2,69,316Document Cost
₹ 2,700Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_PWBNH_38679_3Bid Award Id
ViewTender No
CE/TB-III/28/2024/13 Dated, Guwahati the 20th August/2024Tender Authority
Public Works Building And NH Department ViewPurchaser Address
-Website
http://https://pwdbnh.assam.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Columns, Pillars, Piers, Abutments, Posts and Struts
330.24
-
-
Suspended floors, roofs, landings, balconies and access platform
805.56
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
147.78
-
-
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. (ii)Super Ductile (SD) TMT reinforcement bars
27265.5
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
Cement mortar 1:6 (1 cement : 6 coarse sand)
113.68
-
-
12 mm cement plaster of mix :
1:4 (1 cement: 4 coarse sand)
657.07
-
-
15 mm cement plaster on rough side of single or half brick wall of mix:
1:4 (1 cement: 4 coarse sand)
657.07
-
-
6 mm cement plaster of mix :
1:3 (1 cement: 3 coarse sand)
741.48
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
2055.62
-
-
Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.
Two or more coats on new work
741.48
-
-
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :
Water thinnable cement primer
741.48
-
-
Finishing walls with water proofing cement paint of required shade :
New work (Two or more coats applied @ 3.84 kg/10 sqm)
2055.62
-
-
Finishing walls with textured exterior paint of required shade :
New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm
657.07
-
-
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
2055.62
-
-
Providing and fixing M.S. grills of required pattern in frames of windows
etc. with M.S. flats, square or round bars etc. including priming coat
with approved steel primer all complete.
Fixed to steel windows by welding
2294.58
-
-
Fixed to openings /wooden frames with rawl plugs screws etc
668.7
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
Hot finished welded type tubes(60mm O.D.)
350.88
-
-
Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces),excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
0.63 mm thick
30
-
-
Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.
0.63 mm thick with zinc coating not less than 275 gm/ m²
6
-
-
Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters:
68.04
-
-
Providing and fixing bright finished brass butt hinges with necessar screws etc. complete :
125x85x5.5 mm (heavy type)
10
-
-
100x85x5.5 mm (heavy type)
10
-
-
75x65x4 mm (heavy type)
100
-
-
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :
200x10 mm
10
-
-
150x10 mm
10
-
-
100x10 mm
100
-
-
Providing and fixing bright finished brass door latch with necessary screws etc. complete :
300x16x5 mm
10
-
-
250x16x5 mm
40
-
-
Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
10
-
-
Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.
40 mm
30
-
-
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
50
-
-
Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
4
-
-
Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :
138.96
-
-
Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
425.89
-
-
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
119.7
-
-
Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be lessthan 10 cm. (c) third layer of 1.5 mm thickness consisting of slurry of cement@ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.
(d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.For the purpose of measurement the entire treated surface will be measured.
718.95
-
-
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
21.1.1:For fixed portion
21.1.1.1:Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
312.89
-
-
For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provisionfor fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
21.1.2.1: Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
400.17
-
-
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):
With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
10.5
-
-
Providing wood work in frames of doors ,windows,clerestory windows and other frames,wroght framed and fixed in position with hold fast leg etc.
Kiln seasoned and chemically treated hollock wood
3.32
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with
clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.
Internal work - Exposed on wall
15 mm nominal dia Pipes
30.21
-
-
20 mm nominal dia Pipes
6
-
-
25 mm nominal dia Pipes
10
-
-
32 mm nominal dia Pipes
5
-
-
40 mm nominal dia Pipes
6
-
-
50 mm nominal dia Pipes
6
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making
good the same including testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making
good the walls etc.
15 mm nominal dia Pipes
25
-
-
20 mm nominal dia Pipes
15
-
-
25 mm nominal dia Pipes
25
-
-
32 mm nominal dia Pipes
35
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.
External work
15 mm nominal dia Pipes
10
-
-
20 mm nominal dia Pipes
5
-
-
25 mm nominal dia Pipes
15
-
-
32 mm nominal dia Pipes
2
-
-
40 mm nominal dia Pipes
3
-
-
50 mm nominal dia Pipes
5
-
-
65 mm nominal dia Pipes
3
-
-
80 mm nominal dia Pipes
2
-
-
100 mm nominal dia Pipes
3
-
-
150 mm nominal dia Pipes
4
-
-
Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :
15 mm nominal dia Pipes
35
-
-
20 mm nominal dia Pipes
25
-
-
Providing and fixing G.I. pipes complete with G.I. fittings
including trenching and refilling etc.
External work
15 mm nominal dia Pipes
15
-
-
20 mm nominal dia Pipes
25
-
-
25 mm nominal dia Pipes
25
-
-
32 mm nominal dia Pipes
15
-
-
40 mm nominal dia Pipes
15
-
-
50 mm nominal dia Pipes
10
-
-
65 mm nominal dia Pipes
5
-
-
80 mm nominal dia Pipes
15
-
-
Providing and fixing gun metal gate valve with C.I. wheel
of approved quality (screwed end) :
25 mm nominal bore
10
-
-
20 mm nominal bore
15
-
-
32 mm nominal bore.
5
-
-
40 mm nominal bore
3
-
-
50 mm nominal bore
3
-
-
65 mm nominal bore
3
-
-
80 mm nominal bore
15
-
-
Providing and fixing ball valve (brass) of approved
quality, High or low pressure, with plastic floats complete :
15 mm nominal bore
5
-
-
20 mm nominal bore
5
-
-
25 mm nominal bore
6
-
-
Providing and fixing gun metal non- return valve of approved quality (screwed end) :
25 mm nominal bore
Horizontal
10
-
-
Vertical
10
-
-
32 mm nominal bore
Horizontal
4
-
-
Vertical
5
-
-
40 mm nominal bore
Horizontal
6
-
-
Vertical
5
-
-
Providing and fixing uplasticised PVC connection pipe
with brass unions :
30 cm length
15 mm nominal bore
10
-
-
20 mm nominal bore
25
-
-
45 cm length
15 mm nominal bore
6
-
-
20 mm nominal bore
20
-
-
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :
100 mm diameter
30
-
-
Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump / tube well is lowered and tested :
Beyond 12 m and up to 18 m depth
1
-
-
Providing and placing in position hand pump of approved quality for 40 mm diameter G.I. pipe complete with all accessories.
1
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
3000
-
-
Providing and fixing C.P. brass bib cock of approved quality conforming
15 mm nominal bore
36
-
-
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and
weighing not less than 810 gms.
15 mm nominal bore
10
-
-
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and
weighing not less than 690 gms.
15 mm nominal bore
36
-
-
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.
15 mm nominal bore
30
-
-
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming
to IS:8931
15mm nominal bore
35
-
-
Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per
direction of Engineer-in-charge.
15
-
-
Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than
106 gms.
36
-
-
Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.
10
-
-
Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after
housing G.I. pipe etc.
55
-
-
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:
White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.
10
-
-
Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required
W.C. pan with ISI marked white solid plastic seat and lid.
3
-
-
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and
C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :
One urinal basin with 5 litre white P.V.C. automatic
flushing cistern
3
-
-
Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C.
automatic flushing cistern, with fittings, standard size
G.I. / PVC flush pipe for back and front flush with standard spreader pipes with
fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors
etc. wherever required :
Single squatting plate with 5 litre P.V.C. automatic flushing cistern
6
-
-
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including
painting of fittings and brackets, cutting and making good the walls wherever require:
White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap.
12
-
-
White Vitreous China Angle back wash basin size 600 x 480 mm with single 15mm C.P. brass pillar tap.
12
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,
including painting of fittings and brackets, cutting and making good the walls wherever required :
Kitchen sink with drain board
510x1040 mm bowl depth 250 mm
5
-
-
Providing and fixing white vitreous china water closet
squatting pan (Indian type) :
Orissa pattern W.C. pan of size 580x440 mm
5
-
-
Providing and fixing P.V.C. waste pipe for sink or wash
basin including P.V.C. waste fittings complete.
Semi rigid pipe
32 mm dia
5
-
-
40 mm dia
3
-
-
Flexible pipe
32 mm dia
2
-
-
40 mm dia
2
-
-
Providing and fixing 100 mm sand cast Iron grating for
gully trap.
10
-
-
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :
Rectangular shape 453x357 mm
30
-
-
Providing and fixing soil, waste and vent pipes :
100 mm dia
Sand cast iron S&S pipe as per IS: 1729
10
-
-
Centrifugally cast (spun) iron socket &
spigot (S&S) pipe as per IS: 3989
15
-
-
Hubless centrifugally cast (spun) iron
pipes epoxy coated inside & outside IS:15905
20
-
-
75 mm diameter :
Sand cast iron S&S pipe as per IS: 1729
5
-
-
Centrifugally cast (spun) iron socketed pipe
as per IS: 3989
10
-
-
Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside
IS:15905
10
-
-
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.
100 mm dia
Sand cast iron S&S as per IS - 1729
10
-
-
Sand cast iron S&S as per IS - 3989
20
-
-
Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905
10
-
-
75 mm dia
Sand cast iron S&S as per IS - 1729
15
-
-
Sand cast iron S&S as per IS - 3989
15
-
-
Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per
IS:15905
8
-
-
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with
bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105
gms.
30
-
-
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality
and colour.
450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not
less than 170 gms
29
-
-
Providing and fixing PTMT urinal cock of approved
quality and colour.
15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less
than 48 gms
100
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as
required.
Group B
150
-
-
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with
1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
10
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
150
-
-
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
1400
-
-
2 X 4 sq. mm + 1 X 4 sq. mm earth wire
70
-
-
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
350
-
-
4 X 10 sq. mm + 2 X 6 sq. mm earth wire
100
-
-
4 X 16 sq. mm + 2 X 6 sq. mm earth wire
50
-
-
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required
50
-
-
Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.
100mmx100mmx60mm deep
3
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required
5/6 A switch
300
-
-
2 way 5/6 A switch
12
-
-
15/16 A switch
4
-
-
3 pin 5/6 A socket
80
-
-
6 pin15/16 A socket
4
-
-
TV antenna socket outlet
2
-
-
Bell push
2
-
-
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required
40
-
-
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required
50
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required
3 Module (100mmX75mm)
4
-
-
4 Module (125mmX75mm)
4
-
-
6 Module (200mmX75mm)
12
-
-
12 Module (200mmX150mm
36
-
-
Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.
3 Module
4
-
-
4 Module
4
-
-
6 Module
12
-
-
12 Module
36
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required
4
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
4
-
-
Supplying and fixing brass batten/ angle holder including
connection etc. as required.
36
-
-
Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
2
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
12 way , Double door
12
-
-
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)
4 way (4 + 12), Double door
3
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Single pole
110
-
-
Double pole
12
-
-
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
40A
12
-
-
Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
63A
6
-
-
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
2
-
-
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
50
-
-
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
2
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
Above 35 sq. mm and upto 95 sq. mm
50
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3½ X95 sq. mm (45mm)
8
-
-
Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3½ X 95 sq. mm
8
-
-
Providing and fixing lighting conductor finial made of 25mm dia.300mm long GI tube having single prong at the top with 85mm dia. 6mm thick GI base plate including making hole etc as required complete.
2
-
-
Installation,testing and commissioning of prewired fluorescent fitting compact fluorescent fitting of all types complete with all accesssories and tube/lamp etc. directly on ceiling/wall, including connection with 1.5sqmm FRLS PVC insulated,copper conductor, single core cable and earthing etc as required.
100
-
-
Installation,testing and commissioning of ceiling fan, including wiring the down rods of standard length(upto 30cm) with 1.5sqmm FRLS PVC insulated,copper conductor, single core cable and earthing including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
70
-
-
Numbering of ceiling fan/exhaust fan/fluorescent fitting as required.
300
-
-
Installation of exhaust fan in the existing opening, including making good the damages,connection,testing and commissining etc. as required.
Upto 450mm sweep.
25
-
-
Supply, installation, testing and commissioning of wall/ceiling mounting 20W LED polycarbonate tube with inbuilt driver metal heat sink with double sided connection. Crompton or equivalent make.(LT8-20 865(2).
148
-
-
Supply of energy efficient Ceiling fan 1200 mm sweep
(Make- USHA : Model Name :Energia 32 5 star in the existing arrangement.
40
-
-
Supply of 250mm sweep, 900rpm non metalic exhaust fan in the existing hole of the buildintg, Ventil air DX/DX-HS whitef(Havels make,Considering 10% discount and 18%GST)
25
-
-
Supply of power cables,solid Aluminium conductor upto10sqmm balance stranded conductor,XLPE insulated, core laid up, PVC tape/Extruded innersheathed for multicore cables, Armoured(Aluminium wire for single core upto 70sqmm balance Aluminium strip, Galvanised wire for cables upto 2x10sqmm, 4X6 sqmm balanced all galvanised steel strip),extruded PVC type ST2 sheathed, 650/1100V grade as per IS 7098(Part-I) 1988.
3&1/2 core ,95sqmm cable.
60
-
-
Supplying including installation, commissioning of vermin and dust proof totally enclosed, Phosphatised Powder Painted cubical indoor type floor/wall mounting compartmentalize panel board of size 0.90M(B)X 1.25M(H) X 0.40M(D) made of 16 SWG (1.66 mm) thick C.R. sheet and 35mm X 35mm X 5mm size angle having 4 nos legs at the bottom. The panel board is to be errected in 1 : 3 : 6 PCC foundation including brick soling / grouting etc. complete neatly wiring done with provision for one no 125A 4pole MCCB or Switch Fuse Unit as incomer and provision for 6nos DP or TPN out going as specified and directed by the deptt. confirming to IP 43 protection comprising of the following electrical items:
1. i) 30mm X 5mm 4 strip copper Bus - Bar 1.20 M length
each
ii) 20mm X 3mm 4 strip copper Bus-Bar 0.5M each 4 sets
2. Poilt Lamp with integral ckt LED 110- 230 V (Red,Yellow,&
Blue) - 3 nos
3. Voltmeter & Ammeter Selector Switch - 2 nos
4. 2 A Slide fuse unit - 3nos
(Incoming & Outgoing Switch Gear of reqd. rating along with Meters will be measured and paid separately)
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements