Assam Police Housing Corporation Limited Tender
BidAssist is a very user-friendly website which helps in finding the specific Assam e-tender that one is looking for. For getting any information or detail about any e-tender the Assam government must have posted, BidAssist is designed in such a manner so as to provide information on all government tenders in one place without any inconvenience.
Costs
EMD
₹ 2,71,326Document Cost
₹ 10,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2020_APHC_18571_1Bid Award Id
ViewTender No
APHC/CS/09/2020-21_D_MajuliQtrTender Authority
Assam Police Housing Corporation Limited ViewPurchaser Address
-Website
http://https://police.assam.gov.in/portlet-innerpage/assam-police-housing-corporation-ltd
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Supplying, fitting and fixing in position reinforcement bars confirming to relevant IS code, for reinforced cement concreteworks in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcement as per specified IS codes of practice. (Inclusive of lap length, hook, chair, bend, anchor etc.) : (A) TMT bar made of Primary producer (From Primary producer)
100.08
-
-
Demolishing R.C.C./ P.C.C. pile head of different diameters carefully without disturbing the remaining portion of the pile including opening out of the pile head to be demolished by excavating the earth upto required depth and clearing the debris as directed.
12.8
-
-
Routine test for test loading to 1.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)
401
-
-
Initial test for test loading to 2 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)
100
-
-
Surface dressing of ground including removing vegitation and/ or undulation of ground not exceeding 150mm deep and disposal of rubbish outside the periphery and lift up to 1800mm in all kinds of soil.
850.03
-
-
Jungle clearence including uprooting of vegitation, grass, brush-wood, sapling and trees not exceeding 300mm girth and disposal of the same outside the periphery and lift upto 1500mm
854
-
-
Earth work in Excavation for foundation trenches of walls , Retaining walls, footing of column , steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work , breaking clods in return filling , dressing Watering and ramming etc.and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Upto a depth of 2 mts. below the existing Ground Level (a) In ordinary Soil
149.48
-
-
Supplying and filling sand gravel in foundation trenches of column footings over slushy soil including local carriage of materials within 8 km pumping out of water, ramming etc. complete for strengthening the bearing capacity of the soil as directed and specified including payment of Forest Royalty and Sales Tax and other duties and taxes as may be necessary.
10
-
-
Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary.(c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.
243.72
-
-
Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. (b) Other than Guwahati city
760
-
-
Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling.
670.65
-
-
Plain cement concrete floor base in prop1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. b) 50mm thick
60
-
-
Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (a) In prop 1cement: 3 sand :6 coarse aggregate by volume
43.17
-
-
Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine(A) In substructure up to plinth levelFoundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level.N) Without using admixture, plasticiser b) M20 grade concrete or Prop. 1:1.5:3
105.69
-
-
(B) In super structure from plinth level up to 1st floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing.N) Without using admixture, plasticiser b) M20 grade concrete or Prop. 1:1.5:3
99.93
-
-
Providing formwork of ordinary timber planking so as to give a rough finish including centering, shuttering , strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0 m and removal of the same for cast - in - situ reinforced concrete and plain concrete work: In Substructure upto Plinth Level : Foundation, footings, base of columns, pile cap, raft and mass concrete works etc. (ii) Using 25mm thick plank
359.04
-
-
Sides of tie beams, plinth beams, grade beams etc. at or below plinth level Using 25mm thick plank
243.56
-
-
Columns, Pillars, Posts & Strut (a) Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face (ii) Using 25mm thick plank
43.5
-
-
Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M.(ii) Using 25mm thick plank
80
-
-
Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness. (ii) Using 25mm thick plank
120.84
-
-
Vertical surface such as walls (any thickness), parapet walls, partitions, walls of septic tank, inspection pit and the like including attached pilasters, butresses, plinth and string courses and the like.(ii) Using 25mm thick plank
50.2
-
-
Providing form work of 12mm thick Plywood Board so as to give a rough finish including centering, shattering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in : Columns, Pillars, Posts & Strut of square/ rectangular/ polygonal in plan or any shape like Tee/L etc. having plane vertical face
159.1
-
-
Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal ties. (a) For depth not exceeding 1.0M.
417.86
-
-
Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness.
933.04
-
-
Staircase with sloping or stepped soffits including risers and stringers but excluding Landing.
32
-
-
Brick work in cement mortar with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-structure upto plinth level including dewatering if necessary (C) In proportion 1:5
24.18
-
-
1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In cement mortar in proportion 1:4 (1 cement:4 sand)
761.18
-
-
Extra for brick walling for each subsequent floor or part thereof above the 1st floor level. (a) 112mm thick brick/ R.B wall
761.2
-
-
Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete.
(No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL(ii)Super Ductile (SD) TMT reinforcement bars
196
-
-
Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor.(a) 15 mm thick
240.26
-
-
Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm) (I) Thickness = 1.5 mm
2616
-
-
Applying one coat of alkali resistance primer of approved brand and manufacture on wall surface after throughly brushing the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.
2616
-
-
Wall painting (two coats) with Plastic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a).Plastic Emulsion Paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac)
2616
-
-
Applying one self-priming coat of acrylic emulsion coating of Unicem "Rakshak" brand by thinning 1ltrs of paints with 1ltrs of water over freshly plastered wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth as specified and directed by the department.
601
-
-
Finishing wall with two coats of acrylic emulsion exterior coatings of of required shade by thinning by adding water as per the specification of the manufacturer after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specified and directed by the department. ) Asian paint/Berger paint/Nerolac
400.07
-
-
Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department) a) Normal range Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make ii) Of size 600mmx600mm and above
440.93
-
-
Providing Antiskid Tiles of approved quality size, shape not less than 8mm on floor, skirting over a cement mortar bed 15mm thick of 1:3 (1 cement: 3 coarse sand) approved make fix with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/ white cement complete at all level as specified and directed. (B) VITRIFIED TILES i)Normal range (Sizes 300 mm x 300mm and above) (Premium)
22
-
-
Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). b) Executive range Somany/ Orient/Nitco/Asian Make ii) Of size 250mmx350mm and above
81.6
-
-
Providing 18mm thick Granite slab on vertical face of pedestal laid over 10 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed with approved quality of shade.
11
-
-
Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately). (b) 1.60mm thick sheet (iii) Size 125mm x 60mm (Single rebate)
186
-
-
Providing and fixing Flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panel conforming to relevent to IS Code including oxidised iron butt hinges (100 mm X 75 mm X 3.5 mm) 6 nos. with necessary wood screws. (b) Decorative type face panel and block board core. (i) 35 mm thick
68.67
-
-
Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements, screws etc as required complete as specified and directed for all levels. (b)3 Track sliding window (iv) 5 mm clear glass
131.81
-
-
Providing, fitting and fixing coloured anodised aluminium windows and ventilators of standard sections of approved brand without horizontal glazing bars joints mitred and welded (manufactured to relevant IS specifications) fitted with 6mm x 3.15mm lugs 100mm long embedded in CC blocks 150mm x 100mm x 100mm in 1:3:6 mix including providing and fixing handles, frictions stays, joining cleat, bolting device, locking arrangement, spring catch as required complete as specified and directed for all levels.(Cement concrete to be measured and paid separately). (b)Fixed windows and ventilators (iii)6mm coloured glass
1.46
-
-
Providing Pre Painted Galvanized Iron Sheet Roofing (PPGI) at all levels including fitting and fixing with self drilling, self tapping screws complete. (Roof trusses, purlins etc. to be measured and paid separately.) TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (v) 0.60 mm thick
65
-
-
Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges / Valley / Gutter /Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete complete.
TATA Blue scope/ Dyna roof / Durakolor /Wonder Roof or equivalent as directed by the Departement (v) 0.60 mm thick
31.65
-
-
Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S. circular hlollow section of Grade 210 including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997
4.57
-
-
Pre construction anti - termite treatment at the bottom of foundation pits and walls on either side up to a height of 300mm from bottom of the excavation made for column plinth beam, wall, trenches etc. by applying the emulsion @ 5 (five) litres per square meter of the surface area before starting construction work (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete. b) with aqueous emulsion having concentration 1:499 with Premise 350 SC (Imidachloprid 30.5% SC) and water, i.e. 0.07% solution.
1134.25
-
-
Pre construction anti - termite treatment in the back fill in immediate contact with the foundation structure after completion, column, wall etc. to a depth of 450mm and width 300mm (when required refill in 200mm thick layers) applying the emulsion @ 5 (five) litres per square meter towards the concrete and masonry walls so as to ensure earth in contact with the structure well treated - with chemical (supplying of necessary tools and accessories by the contractor) as per the direction of the Department complete.b) with aqueous emulsion having concentration 1:499 with Premise 350 SC (Imidachloprid 30.5% SC) and water, i.e. 0.07% solution.
406.3
-
-
Providing plinth protection 50mm thick to cement concrete 1 : 3 : 6 with coarse agg.of 20mm nominal size including finishing the surface with 10mm thick cement plaster in proportion 1:3 with a floting coat of neat cement finished.
90.75
-
-
Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. i). 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm.
160.8
-
-
Providing precast R.C.C slab over drain ,septic tank etc. in prop. 1:2:4 reinforced with 10mm M.S. bar @ 150mm centre both ways tying with 20 gauge black annealed wire with necessary shuttering , curing etc. complete including fixing in position as directed. b) 75mm thick slab
10.05
-
-
Providing and fixing Stainless steel (Grade 304) railing made of Hollow tubes, channels, plates, etc. including welding , grinding buffing, polishing and making curvature, (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete , i.e. fixing the railing with necessary accesories & stainless steelm dash fasteners , stainless steel bolts etc. of required size, on top of the floor or the side of waist slab with suitable arrangement as per the approval of Engineer in-charge .(For payment, only weight of stainless steel member is to be considered . No extra payment for fixing accessories such as nuts, bolts, fasteners etc. will be considered. (a) SS Railing Steel with Wire Locator.
316
-
-
15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side b) In cement mortar 1:4
413.83
-
-
B) On fair side b) In cement mortar 1:4
1108.52
-
-
15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side a) In cement mortar 1:3
1094.13
-
-
Extra over item no 6.2.1 to 6.2.3 for plastering on celling and soffits of stairs up to 1st floor level (instead of plastering on walls) including curing complete as directed.
1094.13
-
-
Applying primary coat over new steel and other metal surface over 100 mm in with or girth after preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes, fine steel, would scrapers and sand paper. (a) With ready mixed "Red-Lead"/red oxide primer
1964
-
-
Painting two coats (Excluding priming coats) on new steel and other metal surface with enamel paint of approved brand and manufacture to give an even shade including cleaning the surfaces of dirt, dust and other forein matters. (i) Surfaces over 100mm in width or girth b). High gloss (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).
1964
-
-
Supplying, fitting and fixing anodized aluminium fittings of approved make, reasonably smooth, free from sharp edges flaws and other defects and with counter sunk holes for screws including necessary screws etc. complete ( anodized to bright natural matt or satin finish) (a) Sliding door bolts (i) 300 mm x 16 mm
34
-
-
(b) Tower Bolt (ii) 250 mm x 12 mm
34
-
-
(c) Door Handle (ii) 100 mm
58
-
-
(d) Butt Hinges vi) 100mm x 63mm x 3.2 mm
58
-
-
(m) Mortise lock v) pin cylinder Mortise Lock Oliver/Matiz/Victoria -Godrej make
20
-
-
m) Mortice lock vertical type iv) Aldrop with In built Lock-6 lever kadi tala(Godrej Make)
500
-
-
(r) Curtain rod ii) 25mm x 2mm thick
36
-
-
Providing, fitting and fixing M.S. grill of required pattern for windows/ clerestory windows/ openingwith M.S. flats at required spacing in frame all round, squre or round M.S. bars with round headed bolts and nuts or screws. I . Plain grill (c) Fixed to Brickwork/P.C.C/R.C.C.
659.03
-
-
WATER PROOFING Providing and applying over roof/ raft slab, two coats of waterproofing slurry prepared with cement, fine sand in prop 1:1 admixed with modified acrylic polymer like Cemflex of Sika India Ltd./Dr. Sealkit Sealcrete (Asian Chemicals),/ RHEOMIX 131 OF BASF by brush @ 0.25% of cement-sand mixture (by weight) after proper surface preparation (surface preparation including thorough cleaning of surface to be measured and paid separately) as specified & directed by the Department complete.
47.47
-
-
Providing Grouting in R.C.C. walls & slabs by drilling holes @ 300mm c/c upto half of the wall depth in zigzag manner or as per drawings using a drill machine and fixing a nozzle of 20mm dia. for injecting a grout/ grout slurry till the refusal of injected grout material from adjacent nozzle (grouting operation pressure shall be in between 2 to 4kg per sq.cm.). Followed by cutting the exposed nozzle so as to make the wall free from the grouting pipes and to seal the gap with polymer modified mortar as specified and directed by the Department complete at all levels. (a) Grout slurry of cement, water and grout admixture Cebex 100 of Fosroc Chemicals /Flowcable 50 of BASF/Dr. Sealkit NSPG (Asian Chemicals) @ 225gms per bag of cement
30
-
-
DISMANTLING WORKS:-
Demolishing RCC work including stacking of steel bars and disposal of unserviceable material as directed for all levels
9
-
-
Extra for scraping, cleaning and straightening reinforcement from RCC or RB work at all levels
2197
-
-
Demolishing plain cement concrete including disposal of debris as directed for all levels(i) Prop (1 : 4 : 8) or leaner mix
20
-
-
Demolishing plain cement concrete including disposal of debris as directed for all levels (ii) Prop (1 : 3 : 6) or richer mix
5.9
-
-
Dismantling of existing steel windows/ steel ventilators/ steel windows and steel ventilators without damaging the walls, removing to a safe place and necessary repairs to the edges of walls.
42
-
-
Demolishing RB work including stacking of steel bars and disposal of unserviceable material as directed for all levels
65
-
-
Demolishing brickwork including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels
18
-
-
Extra for cutting reinforcement in RCC or RB work at all levels (Payment to be made on cross sectional area of RCC or RB work obtained by multiplying the length of the cut reinforcement and thickness of the member).
55
-
-
Dismantling wood work in frames, trusses, purlins and rafters including stacking the materials as directed by the department for all levels.
12.67
-
-
Dismantling steel work in built up sections in joists, angles, channels, tees, flats etc. including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking the materials as directed by the Department for all levels
200
-
-
Dismantling and removing the existing door and window frame (chowkath) both wooden and steel of different sizes without damaging the walls and removing the frame and necessary repairs to the edges of the walls as directed for all levels. (i) Area of door/window up to 3.00 m2
12
-
-
(ii) Area of door/window above 3.00 m2
22
-
-
Dismantling all types of corrugated/ trapezoidal sheet roofing including ridges, hips, valleys and gutters etc. and stacking the materials as directed by the department for all levels
211.25
-
-
Demolishing the plastering from walls/ R.C.C. and P.C.C. members without causing any damage to the wall/ member upto any height including disposal of debris as directed for all levels.
1.2
-
-
Demolishing CC floors of various thickness including top layer and base course and disposal of debris as directed for all levels.
124
-
-
Dismantling steel work in single sections (R.S.Joists, channels, angles, tees and flats etc.) including dismembering and stacking the materials as directed by the Department for all levels.
2247.2
-
-
Dismantling all types of ceiling, partition and wall lining and stacking the materials as directed by the department for all levels
169
-
-
Structural steel work in single sections including cutting, hoisting, fixing in position and applying a priming coat of red lead paint (up to 4.6m height) from plinth level including drilling holes, supplying, fitting and fixing with bolts and nuts or welding, if necessary as directed. c) In M.S. angles, channels, Tees etc.
0.26
-
-
Providing plinth protection with bricks flat laid in cement mortar 1: 4 and finished with 15mm thick cement plaster in prop. 1:2 with a floating coat of neat cement finish.
20.79
-
-
INTERNAL ROAD: Construction of Sub-grade and earthen shoulders with approved materials obtained from borrow pits, with all lifts & leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 (including compensation of earth ). (Including cost of testing of materials at site and laboratory as directed by the deptt.) b) from Government land
132
-
-
Construction of Granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per Clause 401 of MoRTH specifications (with an initial lead of 5 km) (including cost of testing of materials at site and laboratory as directed by the deptt.) (a)Using Grading I material
22
-
-
Providing and laying of inter locking concrete block pavement (ICBP) with cement concrete paver blocks as per IS 15658-2006 of thickness 80mm and 28 days compressive strength not less than 30 N/m over a layer of bedding sand of compacted thickness 30mm, laid either in stretcher/ running/ herringbone pattern of bonds as directed by the engineer and in proper level and grade and compacted with appropriate equipment such as plat vibrator along with spreading of a thin layer of joint filling sand to fill up the gaps between blocks including construction of edge restraint wherever required complete as per drawings and Technical specification clause 1504 of MORD.
540
-
-
SANITARY & WATER SUPPLY WORKS : Providing fitting and fixing vitreous china pedestal type water closet (European type W.C pan 400mm high ) with seat and lead ,CP brass hinges and rubber buffers , CI/MS brackets , 40 mm dia flush band with fittings including painting of fittings and brackets, required. (Flushing Cistern to be paid separately) B) Hindware make a) White (i) Water closet Green (Cat No.20079) (inclusive of seat cover)
6
-
-
Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately) ii) Hindware make a) White (i) Sleek+ PVC cistern
6
-
-
Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15mm dia. of Sona make with wall flange as directed and specified.(pipes will be measured and paid separately) (b)Apex/Kiran/Priya/Star/RimZim/Bugle shower with arm
6
-
-
Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) Basin (without pedestal) (B) Hindware Make (a) White (i) Alto 510 x 400 (Cat. No.10091)
6
-
-
Providing fitting & fixing stainless steel kitchen sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately (A) Parryware Make (i) Single Bowl with Veg Bowl & Drain Board (400 x 200) Flat Edge- Glossy (Cat.No.C8545)
6
-
-
Providing, fitting and fixing CP soap tray / soap dish complete as directed and specified. (i) Jaquar Make (a) Continental (Cat.No.ACN-1331N)
6
-
-
Providing, fitting and fixing Decorative Mirror of Agmeco make colour CP frame complete as directed and specified. (A) Parryware Make (b) Size 600mm x 450mm
6
-
-
Providing, fitting and fixing CP towel rail complete as directed and specified. (a) Jaquar make (iii) Queen's (600mm long) (Cat.No.AQN-7711)
6
-
-
Providing, fitting and fixing CP towel ring of Jaquar make complete as specified and directed (a) Jaquar make (i) Continental towel ring square (Cat.No. ACN-1121)
6
-
-
Providing, fitting and fixing Chrome Plated waste coupling complete as directed and specified.(b) Sona (iii) Rupa 50mm (HT/ FT) (Cat.No.WS-0801)
6
-
-
Providing, fitting and fixing Chrome Plated bottle trap complete as directed and specified. ii) Bottle trap Indian 40 mm (Cat. No. BT- 0752)
6
-
-
Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (ii) Jaquare make (a)Continental /Clarion (i)Standard
12
-
-
Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified.(G.I. & C.P pipes will be measured and paid separately) I) Jaquar (b) Queen's collection (ii) concealed stop cock with adjustable wall flange
12
-
-
Supplying fitting and fixing Chrome Plated (C.P.) sink cock of approved brand as directed and specified. (G.I. & C.P pipes will be measured and paid separately) (V) Jaquar brand a) Continental / Clarioni) Sink cock with swinging casted spout
6
-
-
Supplying and fitting fixing C.P. pillar cock of 15mm dia of approved brand as specified and directed. (ii) Jaguar make (b)Long neck with areator
6
-
-
Supplying Fitting and fixing C.P. basin mixer complete as directed (III) Jaquar make b) Queen's Collection (i) Central hole basin mixer with regular spout without popup waste system with 450 mm long copper pipes and brass nuts Cat No. 7167
6
-
-
Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcoal covered with earth over a layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table.
6
-
-
Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.
6
-
-
Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. (Soil + Waste + Rain Water) a) In exposed surfaces or in trenches. (ii) 110mm dia.
40
-
-
(iv) 75mm dia.
40
-
-
b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. (ii) 110mm dia.
125
-
-
(iv) 75mm dia
125
-
-
Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.
10
-
-
(v) 50mm dia
10
-
-
Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. b) Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.(ii) 110mm dia.
10
-
-
(v) 50mm dia
10
-
-
Supplying fiting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.
40
-
-
Supply fitting and fixing PVC single 'Y' of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. (B) Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. ii) 110mm dia.
10
-
-
(v) 50mm dia
10
-
-
Supply fitting and fixing PVC coupler of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. (B) Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. i) 110mm dia.
10
-
-
ii) 75mm dia.
10
-
-
Supply fitting and fixing PVC reducer of (Supreme/ prince) or other ISI approved including joining, fitting and fixing with long screw fitting, H.W. clamps etc. completed at all levels including bellow G.L. as directed and specified. (B) Concealed by chiselling or breaking brick wall/ c.c./ R.c.c. and making good to the damages. iv) 110mm x 75mm
12
-
-
Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified.(a) 110 mm
12
-
-
Providing fitting and fixing PVC cowel of ISI make complete as directed and specified.(ii) 110mm dia. PVC cowel of ISI make
12
-
-
Providing fiting & fixing C.I. Grating to the floors complete as directed and specified.(a) 110mm dia
10
-
-
(b) 75mm dia
2
-
-
Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and specified.
(Note: Ball valve and union will be charged extra and does not comes under Accessories)(i) exposed on wall (a) 15 mm OD
5
-
-
(b) 20 mm OD
10
-
-
(c) 25 mm OD
20
-
-
(d) 32 mm OD
10
-
-
(e) 40 mm OD (Terrace Header)
10
-
-
(f) 50 mm OD (Terrace Header)
10
-
-
(ii) Concealed by chiselling or breaking brick wall/C.C/R.C.C and making good to damages (a) 15 mm OD
20
-
-
(b) 20 mm OD
35
-
-
(c) 25 mm OD
25
-
-
Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed C) CPVC pipe with CPVC fittings FOR EXTERNAL USE
(Using SUPREME/ PRINCE/ SFMC/ FUSION brand pipe)
ii)20mm (OD) diameter
2
-
-
iii) 25mm (OD) diameter
2
-
-
iv) 32 mm (OD) diameter
2
-
-
v) 40 mm (OD) diameter
2
-
-
vi) 50mm (OD) diameter
20
-
-
Supplying, fitting and fixing Chrome Plated (C.P.) wall mixer complete as directed. (III) Essco make e) Wall mixer with 115mm long bend pipe for connection to overhead shower (with bush and piston divertor fitting)Cat No.517B
4
-
-
Supplying and fitting gun metal country pit valve (full way valve) I.S.I. Make as specified and directed.a) 50mm dia
2
-
-
b) 40 mm dia.
24
-
-
c) 25 mm dia.
2
-
-
Supplying and fitting ball valve as specified and directed..a) 25 mm dia. (gun metal)
2
-
-
Supplying fitting and fixing G.I. Foot valve with strainer including cutting necessary threads to pipes. a) 50 mm dia (Heavy type)
2
-
-
Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department .iv) Bore hole of 150 mm diameter
30
-
-
Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department.(ii) P.V.C.pipe SUPREME /PRINCE / FUSION /SFMC Brand v) 110mm diameter
85
-
-
Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed. A) G.I. pipe a) TATA / SAIL (Medium)socket should be welded to the pipes. ii) 32mm diameter
110
-
-
Supplying fitting and fixing ISI approved PVC filter 3.00 metre long.
1
-
-
Supplying fitting and fixing check valve (non return valve) including thread to pipes.vii) 100mm diameter
1
-
-
Development of the tube well with compressor or by over pumping unit for 48 hours till sand free discharge is obtained
1
-
-
Flushing, clearing, washing and watering of the tube well
1
-
-
Supplying fitting and fixing iron removal filter filling with treated sand, pebbles, manganishdioxide and other required materials of various filtration rate per hour of DOLPHIN make with all necessary fittings such as valve,bib cock,pipe connection etc.with a free maintanance period of six months. (A) With Zoloto fittings. (II) 2000 liters capacity (a) 4 mm thick Vessel
2
-
-
Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon / Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes (I) 2000 Lt capacity (a) Sintex make
2
-
-
Labour for erecting and placing PCVCTank over the stagging of 5.00m up to 8.00m complete as directed. (a) 2000 litre capacity
2
-
-
Supplying and Installation of 1.5 H.P. Crompton Greaves Single phase Pump Submersible Pump Set including necessary Cable for underground and overground. Panel Board as directed by the Department.
2
-
-
Supply & fitting inner PVC kit at Bio S/ Tank (I)
13.15
-
-
Anaerobic Microbial Bacteria (AMI) for Bio Digerster @30% of the tank capacity
2100
-
-
Maintenance Legacy 2nd Year Area : RCC Portion 3.15 M height
Ground Floor
1260.63
-
-
Maintenance Legacy 3rd Year Area : RCC Portion 3.15 M depth
Ground Floor
1260.63
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements